Skip to the content
561111

TPS61089RNRR

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 1uA 2.2MHz 2.7V~12V 4.5V~12.6V 7A Adjustable Boost Boost Built-in Yes VQFN-11-HR-EP(2x2.5) DC-DC Converters ROHS

Part id
ti/TPS61089RNRR
Category
DC DC Converters
Package
VQFN-11-HR-EP(2x2.5)
Pins
11
In stock
1,489 at JLCPCB (C165129)
Used on
10 open-source boards

Overview

The TPS61089RNRR is a DC DC Converter made by Texas Instruments in a VQFN-11-HR-EP(2x2.5) package with 11 pins. -40℃~+125℃@(TJ) 1 1uA 2.2MHz 2.7V~12V 4.5V~12.6V 7A Adjustable Boost Boost Built-in Yes VQFN-11-HR-EP(2x2.5) DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:TPS61089, from KiCad's library) and its footprint (Package_DFN_QFN:Texas_VQFN-RNR0011A-11, from KiCad's library), ready for a KiCad board. 1,489 are in stock at JLCPCB (part C165129). 10 open-source boards in 8 repositories on GitHub use it.

Symbol

1FSW2VCC3FB4COMP5GND6VOUT7EN8ILIM9VIN10BOOT11SW
Regulator_Switching:TPS61089From KiCad's library

Footprint

561111
Package_DFN_QFN:Texas_VQFN-RNR0011A-11From KiCad's library

From the datasheet

16
Supply, least
2.7 V · VIN, recommended operating min · p. 5
Supply, most
12 V · VIN, recommended operating max · p. 5
Supply, absolute maximum
14.5 V · VIN, absolute max · p. 5
Junction, hottest
150 °C · junction temperature, absolute max · p. 5
Takes working
101 µA · sum of VIN and VOUT typical quiescent currents, enabled, no load · p. 6
Takes asleep
1 µA · VIN typical shutdown current, disabled, VIN = 2.7 V to 5.5 V, TJ ≤ 85°C · p. 6
Feedback reference
1.212 V · FB typical reference, PWM mode · p. 6
Feedback reference
1.224 V · FB typical reference, PFM mode · p. 6
Switches at
500 kHz · typical switching frequency, RFSW = 301 kΩ · p. 6
Switches at
2 MHz · typical switching frequency, RFSW = 46.4 kΩ · p. 6
Current limit
8.1 A · typical peak switch current limit, RILIM = 127 kΩ · p. 6
Current limit
10 A · typical peak switch current limit, RILIM = 100 kΩ · p. 6
Junction to air (RNR (VQFN))
53.4 K/W · junction-to-ambient thermal resistance · p. 5
Junction to case (RNR (VQFN))
59.2 K/W · junction-to-case top thermal resistance · p. 5
Junction to board (RNR (VQFN))
9.6 K/W · junction-to-board thermal resistance · p. 5
Junction to air (RNR (VQFN))
39.2 K/W · junction-to-ambient thermal resistance on EVM · p. 5

What it is and has

9
Input voltage range
2.7 V to 12 V · p. 1
Output voltage range
4.5 V to 12.6 V · p. 1
Soft start
4 ms built-in · p. 1
Light-load operation
PFM · p. 1
Protection
Internal output overvoltage protection at 13.2 V · p. 1
Protection
Cycle-by-cycle overcurrent protection · p. 1
Protection
Thermal shutdown · p. 1
Package
2.00-mm × 2.50-mm VQFN HotRod · p. 1
Continuous switch current
7 A · p. 1

Around it

7
cap >1.0 µF
between VCC and GND; Required ceramic capacitor at the internal regulator output. · p. 4
cap ≥10 µF
between VIN and GND; Minimum effective input capacitance in recommended operating conditions. · p. 5
cap 47 µF
between VOUT and GND; Nominal effective output capacitance; recommended range 10 to 1000 uF. · p. 5
ind 2.2 µH
between VIN and SW; Nominal effective inductance; recommended range 0.47 to 10 uH. · p. 5
res 127 kΩ
between ILIM and GND; Example resistor for a typical current limit of 8 A. · p. 10
res 301 kΩ
between FSW and SW; Switching-frequency setting resistor for a typical 500 kHz. · p. 6
res 46.4 kΩ
between FSW and SW; Switching-frequency setting resistor for a typical 2000 kHz. · p. 6

Specifications

53
ParameterConditionsAs printedPage
Voltage at terminalsBOOT; maximum SW + 7 V; voltages relative to groundmin -0.3 V5
Voltage at terminalsVIN, SW, FSW, VOUT; voltages relative to groundmin -0.3 · max 14.5 V5
Voltage at terminalsEN, VCC, COMP; voltages relative to groundmin -0.3 · max 7 V5
Voltage at terminalsILIM, FB; voltages relative to groundmin -0.3 · max 3.6 V5
Operating junction temperature TJmin -40 · max 150 °C5
Storage temperature Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; rating ±2000 Vmax 2000 V5
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; rating ±500 Vmax 500 V5
Input voltage range VINmin 2.7 · max 12 V5
Output voltage range VOUTmin 4.5 · max 12.6 V5
Inductance, effective value L2.2 uH is NOMmin 0.47 · typ 2.2 · max 10 uH5
Input capacitance, effective value CINmin 10 uF5
Output capacitance, effective value CO47 uF is NOMmin 10 · typ 47 · max 1000 uF5
Operating junction temperature TJmin -40 · max 125 °C5
Junction-to-ambient thermal resistance RθJARNR (VQFN), 11 PINStyp 53.4 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)RNR (VQFN), 11 PINStyp 59.2 °C/W5
Junction-to-board thermal resistance RθJBRNR (VQFN), 11 PINStyp 9.6 °C/W5
Junction-to-top characterization parameter ψJTRNR (VQFN), 11 PINStyp 0.5 °C/W5
Junction-to-board characterization parameter ψJBRNR (VQFN), 11 PINStyp 9.5 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)RNR (VQFN), 11 PINStyp 0.7 °C/W5
Junction-to-ambient thermal resistance on EVM RθJA(EVM)RNR (VQFN), 11 PINS; 4-layer EVM PCB, 76-mm x 52-mm; outer copper 2 oz, inner copper 1 oztyp 39.2 °C/W5
Input voltage undervoltage lockout (UVLO) threshold VIN_UVLOVIN risingmax 2.7 V6
Input voltage undervoltage lockout (UVLO) threshold VIN_UVLOVIN fallingtyp 2.4 · max 2.5 V6
VIN UVLO hysteresis VIN_HYStyp 200 mV6
VCC regulation voltage VCCICC = 2 mA, VIN = 8 Vtyp 5.8 V6
VCC UVLO threshold VCC_UVLOVCC fallingtyp 2.1 V6
Quiescent current into VIN pin IQIC enabled, No load, VIN = 2.7 V to 5.5 V, VFB = 1.3 V, VOUT = 12 V, TJ ≤ 85°Ctyp 1 · max 3 uA6
Quiescent current into VOUT pin IQIC enabled, No load, VIN = 2.7 V to 5.5 V, VFB = 1.3 V, VOUT = 12 V, TJ ≤ 85°Ctyp 100 · max 180 uA6
Shutdown current into VIN pin ISDIC disabled, VIN = 2.7 V to 5.5 V, TJ ≤ 85°Ctyp 1 · max 3 uA6
Reference voltage at FB pin VREFPWM modemin 1.188 · typ 1.212 · max 1.236 V6
Reference voltage at FB pin VREFPFM modetyp 1.224 V6
Leakage current into FB pin IFB_LKGVFB = 1.2 Vmax 100 nA6
Output overvoltage protection threshold VOVPVOUT risingmin 12.7 · typ 13.2 · max 13.6 V6
Output overvoltage protection hysteresis VOVP_HYSVOUT falling below VOVPtyp 0.25 V6
Soft startup time tSSCOUT(effective) = 47 uF, IOUT = 0 Amin 2 · typ 4 · max 6 ms6
COMP pin sink current ISINKVFB = VREF + 200 mV, VCOMP = 1.9 Vtyp 20 uA6
COMP pin source current ISOURCEVFB = VREF – 200 mV, VCOMP = 1.9 Vtyp 20 uA6
High clamp voltage at the COMP pin VCCLP_HVFB = 1 V, RILIM = 127 kΩtyp 2.3 V6
Low clamp voltage at the COMP pin VCCLP_LVFB = 1.4 V, RILIM = 127 kΩtyp 1.4 V6
Error amplifier transconductance GEAVCOMP = 1.9 Vtyp 190 uS6
High-side MOSFET on-resistance RDS(on)VCC = 6 Vtyp 27 · max 44 mΩ6
Low-side MOSFET on-resistance RDS(on)VCC = 6 Vtyp 19 · max 31 mΩ6
Switching frequency fSWRFSW = 301 kΩtyp 500 kHz6
Switching frequency fSWRFSW = 46.4 kΩtyp 2000 kHz6
Minimum on time tON_minVCC = 6 Vtyp 90 · max 180 ns6
Peak switch current limit, TPS61089 ILIMTPS61089; RILIM = 127 kΩmin 7.3 · typ 8.1 · max 8.9 A6
Peak switch current limit, TPS61089 ILIMTPS61089; RILIM = 100 kΩmin 9 · typ 10 · max 11 A6
Internal reference voltage at ILIM pin VILIMtyp 1.212 V6
EN Logic high threshold VEN_Hmax 1.2 V6
EN Logic Low threshold VEN_Lmin 0.4 V6
EN pulldown resistor RENtyp 800 kΩ6
Thermal shutdown threshold TSDTJ risingtyp 150 °C6
Thermal shutdown hysteresis TSD_HYSTJ falling below TSDtyp 20 °C6

Pins, by the datasheet

11
1 FSW
Program switching frequency with a resistor between this pin and SW. · p. 4
2 VCC
Internal regulator output; requires a ceramic capacitor greater than 1.0 uF to ground. · p. 4
3 FB
Output voltage feedback. · p. 4
4 COMP
Internal error amplifier output; connect the loop compensation network to GND. · p. 4
5 GND
Ground. · p. 4
6 VOUT
Boost converter output. · p. 4
7 EN
Logic high enables the device; logic low disables it into shutdown mode. · p. 4
8 ILIM
Adjustable switching peak current limit; connect an external resistor to GND. · p. 4
9 VIN
IC power supply input. · p. 4
10 BOOT
High-side MOSFET gate-driver supply; connect a capacitor between BOOT and SW. · p. 4
11 SW
Switching node connected to the internal low-side MOSFET drain and high-side MOSFET source. · p. 4

Open-source boards using it

10See all 10
  • 6 layers68.8 × 74.6 mmFurbyBoard, the printed circuit board in 3D

    FurbyBoard

    Guilleloma/Furby-GPT

    This project transforms a 1998 Furby into an interactive and advanced desktop assistant using a Raspberry Pi W. It incorporates OpenAI and Whisper for natural language processing, primarily relying on Google Cloud Text…

    158 parts26
  • 4 layers90 × 50 mmCryobelt, the printed circuit board in 3D

    Cryobelt

    michael201110/cryobelt

    100 parts1
  • 4 layers74.9 × 81.3 mmWatersphere MOBO, the printed circuit board in 3D

    Watersphere MOBO

    blanchardp2ATWIT/Watersphere_MOBO

    Senior Capstone project motherboard.

    112 parts
  • 4 layers85 × 43 mmRicardo Kermit Mini, the printed circuit board in 3D

    Ricardo Kermit Mini

    icl-rocketry/Ricardo-Kermit

    Data Acquisition (DAQ) board

    210 partsMIT
  • 6 layers117 × 49 mmRicardo Stark, the printed circuit board in 3D

    Ricardo Stark

    icl-rocketry/Ricardo-Stark

    An integrated engine control unit designed to fire and control liquid bi-propellant rocket engines.

    321 parts
  • 4 layers100 × 100 mmM09A GroupG pcb, the printed circuit board in 3D

    M09A GroupG pcb

    Jackson-Andrews/Sound-Helmet-PCB

    193 parts
  • 4 layers68 × 60 mmRoboCore V2, the printed circuit board in 3D

    RoboCore V2

    Plastal-Bot-Builders/RoboCoreDocumentation

    RoboCore is a classroom robot kit and coding platform, designed and built in Zambia by Plastal-Bot Builders (Lusaka).

    146 partsMIT

Questions

Is there a KiCad symbol and footprint for the TPS61089RNRR?

Yes. The symbol is Regulator_Switching:TPS61089 and the footprint Package_DFN_QFN:Texas_VQFN-RNR0011A-11, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS61089RNRR?

VQFN-11-HR-EP(2x2.5), with 11 pins. Its footprint is drawn on this page.

Where is the TPS61089RNRR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS61089RNRR?

JLCPCB lists it as part C165129, with 1,489 in stock; the sellers' links on this page open their listings.

Which open-source boards use the TPS61089RNRR?

10 boards in 8 repositories on GitHub; the most starred are listed on this page, with their KiCad files.