TPS3840PL34DBV
Texas InstrumentsExtended
-40℃~+125℃@(TJ) 1 1.5V~10V 3.4V 300nA 619ms Active Low Push-pull Voltage Monitor Yes SOT-23-5 Supervisor and Reset ICs ROHS
- Part id
- ti/TPS3840PL34DBV
- Category
- Supervisor And Reset ICs
- Package
- SOT-23-5
- Pins
- 5
- In stock
- 130 at JLCPCB (C2871627)
Overview
The TPS3840PL34DBV is a supervisor And Reset IC made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+125℃@(TJ) 1 1.5V~10V 3.4V 300nA 619ms Active Low Push-pull Voltage Monitor Yes SOT-23-5 Supervisor and Reset ICs ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TPS3840PL33DBVR, from EasyEDA) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 130 are in stock at JLCPCB (part C2871627).
Symbol
Footprint
From the datasheet
12- Supply, least
- 1.5 V · VDD, recommended operating min · p. 5
- Supply, most
- 10 V · VDD, recommended operating max · p. 5
- Supply, absolute maximum
- 12 V · VDD, absolute max · p. 5
- Works from
- -40 °C · Free-air temperature min · p. 5
- Works up to
- 125 °C · Free-air temperature max · p. 5
- Junction, hottest
- 150 °C · Operating junction temperature absolute max · p. 5
- Takes working
- 300 nA · VDD supply current typical, VDD > VIT+ · p. 6
- Takes at most
- 700 nA · VDD supply current max, VDD > VIT+ · p. 6
- A pin gives at most
- 70 mA · RESET pin source or sink absolute max · p. 5
- Junction to air (DBV (SOT23-5))
- 187.5 K/W · Junction-to-ambient thermal resistance · p. 5
- Junction to case (DBV (SOT23-5))
- 109.2 K/W · Junction-to-case top thermal resistance · p. 5
- Junction to board (DBV (SOT23-5))
- 92.8 K/W · Junction-to-board thermal resistance · p. 5
What it is and has
6- Output topology
- Push-pull, active-low reset · p. 1
- Manual reset
- Active-low · p. 1
- Reset delay
- 50µs without capacitor to 6.2s with 10µF · p. 1
- Threshold accuracy
- 1% typical, 1.5% maximum · p. 1
- Package
- SOT23-5 (DBV) · p. 1
- Protection
- Hysteresis and glitch immunity · p. 17
Around it
2- cap 0.1uF to 1uF
- between VDD and GND; Bypass capacitor at VDD input for noisy applications. · p. 17
- cap no larger than 10µF
- between CT and GND; Programs reset delay; CT may be left floating for minimum delay. · p. 18
Specifications
33| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Voltage VDD | Over operating free-air temperature range | min -0.3 · max 12 V | 5 |
| Voltage RESET | TPS3840PL | min -0.3 V | 5 |
| Voltage MR | VMR must not be higher than VDD | min -0.3 · max 12 V | 5 |
| Voltage CT | min -0.3 · max 5.5 V | 5 | |
| Operating junction temperature TJ | TJ = TA assumed due to low dissipated power | min -40 · max 150 °C | 5 |
| Storage Tstg | min -65 · max 150 °C | 5 | |
| Input supply voltage VDD | Over operating free-air temperature range | min 1.5 · max 10 V | 5 |
| RESET pin and RESET pin voltage VRESET , VRESET | min 0 · max 10 V | 5 | |
| RESET pin and RESET pin current IRESET , IRESET | min 0 mA | 5 | |
| Junction temperature (free air temperature) TJ | min -40 · max 125 °C | 5 | |
| Manual reset pin voltage VMR | VMR must not be higher than VDD | min 0 V | 5 |
| Junction-to-ambient thermal resistance RθJA | TPS3840, DBV (SOT23-5), 5 PINS | typ 187.5 °C/W | 5 |
| Junction-to-case (top) thermal resistance RθJC(top) | TPS3840, DBV (SOT23-5), 5 PINS | typ 109.2 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | TPS3840, DBV (SOT23-5), 5 PINS | typ 92.8 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | TPS3840, DBV (SOT23-5), 5 PINS | typ 35.4 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | TPS3840, DBV (SOT23-5), 5 PINS | typ 92.5 °C/W | 5 |
| Input supply voltage VDD | Common parameters | min 1.5 · max 10 V | 6 |
| Negative-going input threshold accuracy VIT- | -40°C to 125°C | min -1.5 · typ 1 · max 1.5 % | 6 |
| Hysteresis on VIT- pin VHYS | VIT- = 3.1V to 4.9V | min 175 · typ 200 · max 225 mV | 6 |
| Supply current into VDD pin IDD | VDD = 1.5V < VDD < 10V; VDD > VIT+; TA = -40°C to 125°C; CT = MR = Open | typ 300 · max 700 nA | 6 |
| Manual reset logic low input V MR_L | max 600 mV | 6 | |
| Manual reset internal pull-up resistance RMR | typ 100 kΩ | 6 | |
| CT pin internal resistance RCT | min 350 · typ 500 · max 650 kΩ | 6 | |
| Power on Reset Voltage VPOR | TPS3840PL (Push-Pull Active-Low); VOL(max) = 200mV; IOUT(Sink) = 200nA; VDD slew rate ≤ 100mV/us | max 300 mV | 6 |
| Low level output voltage VOL | TPS3840PL (Push-Pull Active-Low); 1.5V < VDD < 5V; VDD < VIT-; IOUT(Sink) = 2mA | max 200 mV | 6 |
| Startup Delay tSTRT | CT pin open | min 100 · typ 220 · max 350 us | 7 |
| Propagation detect delay for VDD falling below VIT- tP_HL | VDD = VIT+ to (VIT-) - 10% | typ 15 · max 30 us | 7 |
| Reset time delay tD | CT pin = open | max 50 us | 7 |
| Reset time delay tD | CT pin = 10nF | typ 6.2 ms | 7 |
| Reset time delay tD | CT pin = 1 uF | typ 619 ms | 7 |
| Glitch immunity VIT- tGI_VIT- | 5% VIT- overdrive | typ 10 us | 7 |
| MR pin pulse duration to initiate reset tMR_PW | typ 300 ns | 7 | |
| Propagation delay from MR low to reset tMR_RES | VDD = 4.5V, MR < V MR_L | typ 700 ns | 7 |
Pins, by the datasheet
5- 1 RESET
- Active-low push-pull reset output; asserts when MR is low or VDD falls below VIT-, and releases after the reset delay when MR is floating or high and VDD rises above VIT+. · p. 4
- 2 VDD
- Input supply voltage; TPS3840 monitors VDD voltage. · p. 4
- 3 GND
- Ground. · p. 4
- 4 MR / NC
- Active-low manual reset input; may be left floating when unused. · p. 4
- 5 CT
- Connect an external capacitor to adjust reset delay; leave floating for the smallest fixed reset delay. · p. 4
Parts like it
8TPS3828-33DBV
SOT-23-5-40℃~+85℃@(TA) 1 1.1V~5.5V 15uA 2.93V 200ms Active Low Open Drain Voltage monitor Watchdog timer、Manual reset input SOT-23-5 Supervisor and Reset ICs ROHSTexas InstrumentsSupervisor And Reset ICsAPX823-26W5G
SOT-25-5-40℃~+85℃@(TA) 1 1.1V~5.5V 2.63V 200ms 30uA Active Low Push-pull Voltage monitor Watchdog timer、Manual reset input SOT-25-5 Supervisor and Reset ICs ROHSDiodes IncorporatedSupervisor And Reset ICsTPS3820-33DBV
SOT-23-5-40℃~+85℃ 1 15uA 2.5V、3V、3.3V、5V 2.93V 25ms Active Low Push-pull Voltage Monitor Yes Yes SOT-23-5 Supervisor and Reset ICs ROHSTexas InstrumentsSupervisor And Reset ICsSTWD100NYWY3F
SOT-23-5-40℃~+125℃@(TA) 1 13uA 2.7V~5.5V 210ms Active Low Open-drain Watchdog timer、Manual reset input SOT-23-5 Supervisor and Reset ICs ROHSSTMicroelectronicsSupervisor And Reset ICsTLV840CADL29DBV
SOT-23-5-40℃~+125℃ 1 120nA 2.9V 29ms 700mV~6V Active Low No No Push-pull Voltage Monitor SOT-23-5 Supervisor and Reset ICs ROHSTexas InstrumentsSupervisor And Reset ICsSTWD100YNYWY3F
SOT-23-5-40℃~+125℃@(Ta) 13uA 2.7V~5.5V 3.4ms Active Low Open Drain、Push-pull Watchdog Timer Yes SOT-23-5 Supervisor and Reset ICs ROHSSTMicroelectronicsSupervisor And Reset ICsTPCAT823TTDI-GT3
SOT-23-5-40℃~+85℃ 1 1V~7V 200ms 4uA Active Low Power Supervisor Yes Yes SOT-23-5 Supervisor and Reset ICs ROHSTECH PUBLICSupervisor And Reset ICsTPS3820-50DBV
SOT-23-5-40℃~+85℃ 1 15uA 2.5V、3V、3.3V、5V 200ms 4.55V Active Low Push-pull Voltage Monitor Yes Yes SOT-23-5 Supervisor and Reset ICs ROHSTexas InstrumentsSupervisor And Reset ICs
Questions
Is there a KiCad symbol and footprint for the TPS3840PL34DBV?
Yes. The symbol is EasyEDA_Cloud:TPS3840PL33DBVR and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TPS3840PL34DBV?
SOT-23-5, with 5 pins. Its footprint is drawn on this page.
Where is the TPS3840PL34DBV datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TPS3840PL34DBV?
JLCPCB lists it as part C2871627, with 130 in stock; the sellers' links on this page open their listings.
What can replace the TPS3840PL34DBV?
Parts like it in the library: the TPS3828-33DBV by Texas Instruments, the APX823-26W5G by Diodes Incorporated, the TPS3820-33DBV by Texas Instruments and the STWD100NYWY3F by STMicroelectronics. Check their datasheets: a part that fits the footprint may still differ in its ratings.