Skip to the content
123456789

TPS2557DRB

Texas InstrumentsExtended

-40℃~+125℃ 1 2.5V~6.5V 22mΩ 5A Active High High Side Switch Overcurrent Protection(OCP)、Overtemperature protection (OTP) SON-8(3x3) Power Distribution Switches ROHS

Part id
ti/TPS2557DRB
Category
Power Distribution Switches
Package
SON-8(3x3)
Pins
9
In stock
6,867 at JLCPCB (C130056)
Used on
15 open-source boards

Overview

The TPS2557DRB is a power Distribution Switche made by Texas Instruments in a SON-8(3x3) package with 9 pins. -40℃~+125℃ 1 2.5V~6.5V 22mΩ 5A Active High High Side Switch Overcurrent Protection(OCP)、Overtemperature protection (OTP) SON-8(3x3) Power Distribution Switches ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TPS2556DRBR, from EasyEDA) and its footprint (Package_SON:VSON-8-1EP_3x3mm_P0.65mm_EP1.65x2.4mm, from KiCad's library), ready for a KiCad board. 6,867 are in stock at JLCPCB (part C130056). 15 open-source boards in 4 repositories on GitHub use it.

Symbol

1GND2IN3IN4EN5ILIM6OUT7OUT8FAULT#9EP
EasyEDA_Cloud:TPS2556DRBRFrom EasyEDA

Footprint

123456789
Package_SON:VSON-8-1EP_3x3mm_P0.65mm_EP1.65x2.4mmFrom KiCad's library

From the datasheet

14
Supply, least
2.5 V · IN, recommended operating min · p. 4
Supply, most
6.5 V · IN, recommended operating max · p. 4
Supply, absolute maximum
7 V · IN, absolute max · p. 4
Takes working
95 µA · IN, typical enabled no-load current, VIN = 6.5 V, RILIM = 24.9 kΩ · p. 5
Takes working
85 µA · IN, typical enabled no-load current, VIN = 6.5 V, RILIM = 100 kΩ · p. 5
Takes asleep
100 nA · IN, typical disabled no-load current, VIN = 6.5 V · p. 5
Gives
5 A · OUT, max continuous output current · p. 4
Current limit
4.45 A · typical current-limit threshold, RILIM = 24.9 kΩ · p. 5
Current limit
1.785 A · typical current-limit threshold, RILIM = 61.9 kΩ · p. 5
Current limit
1.1 A · typical current-limit threshold, RILIM = 100 kΩ · p. 5
A pin gives at most
25 mA · FAULT, absolute max continuous sink current · p. 4
Junction to air (DRB (VSON))
41.5 K/W · junction-to-ambient thermal resistance · p. 5
Junction to board (DRB (VSON))
16.4 K/W · junction-to-board thermal resistance · p. 5
Junction to case (DRB (VSON))
54.5 K/W · junction-to-case (top) thermal resistance · p. 5

What it is and has

11
USB current limiting
Meets USB current-limiting requirements · p. 1
Adjustable current limit
500 mA to 5 A typical · p. 1
Current-limit accuracy
±6.5% at 4.5 A · p. 1
Overcurrent response
3.5 µs typical · p. 1
Power switch
22-mΩ high-side MOSFET · p. 1
Soft start
Built-in · p. 1
System-level ESD
15-kV and 8-kV capable · p. 1
Package
8-pin VSON, 3.00 mm × 3.00 mm · p. 1
Enable polarity
Active high · p. 3
Current limit
Adjustable, 500 mA to 5 A typical · p. 1
High-side MOSFET
22 mΩ · p. 1

Around it

6
cap 0.1-µF or greater
between IN and GND; Ceramic bypass capacitor for all applications; place as close to the device as possible. · p. 13
res 20 kΩ ≤ RILIM ≤ 187 kΩ
between ILIM and GND; 1% resistor programs the current-limit threshold; keep routing short. · p. 14
res 100 kΩ
between FAULT and IN; FAULT pull-up in the typical current-limiting application. · p. 13
cap high-value
between OUT and GND; Electrolytic output capacitor recommended when large output transient currents are expected; output capacitance is not required. · p. 13
res 33.2 kΩ
between ILIM and GND; 1% resistor; example selection for a minimum current-limit threshold of 3000 mA. · p. 15
res 23.7 kΩ
between ILIM and GND; 1% resistor; example selection for a maximum current-limit threshold of 5000 mA. · p. 15

Specifications

43
ParameterConditionsAs printedPage
VoltageIN, OUT, EN or EN, ILIM, and FAULT pinsmin -0.3 · max 7 V4
Voltage from IN to OUTmin -7 · max 7 V4
Continuous FAULT sink currentmax 25 mA4
Maximum junction temperatureMaximum is OTSD2min -40 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±500 Vmax 500 V4
Electrostatic discharge V(ESD)IEC 61000-4-2 contact discharge; ±8000 V; evaluation-module test levelmax 8000 V4
Electrostatic discharge V(ESD)IEC 61000-4-2 air discharge; ±15000 V; evaluation-module test levelmax 15000 V4
Input voltage, IN VINmin 2.5 · max 6.5 V4
Enable voltage VENTPS2557min 0 · max 6.5 V4
High-level input voltage on Enable pin VIHmin 1.1 V4
Low-level input voltage on Enable pin VILmax 0.66 V4
Continuous output current (OUT pin) IOUTmin 0 · max 5 A4
Continuous FAULT sink currentmin 0 · max 10 mA4
Recommended resistor limit RILIMmin 20 · max 187 kΩ4
Operating virtual junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJADRB (VSON), 8 PINStyp 41.5 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DRB (VSON), 8 PINStyp 54.5 °C/W5
Junction-to-board thermal resistance RθJBDRB (VSON), 8 PINStyp 16.4 °C/W5
Junction-to-top characterization parameter ψJTDRB (VSON), 8 PINStyp 0.7 °C/W5
Junction-to-board characterization parameter ψJBDRB (VSON), 8 PINStyp 16.6 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)DRB (VSON), 8 PINStyp 3.6 °C/W5
Static drain-source on-state resistance rDS(ON)TJ = 25°Ctyp 22 · max 25 mΩ5
Static drain-source on-state resistance rDS(ON)–40°C ≤TJ ≤ 125°Cmax 35 mΩ5
Enable pin turn on and off thresholdmin 0.66 · max 1.1 V5
Enable input hysteresisReference onlytyp 55 mV5
Input current IENVEN = 0 V or 6.5 V, VEN = 0 V or 6.5 Vmin -0.5 · max 0.5 uA5
Current-limit threshold (Maximum DC output current IOUT delivered to load) and short-circuit current, OUT connected to GND IOSRILIM = 24.9 kΩmin 4130 · typ 4450 · max 4695 mA5
Current-limit threshold (Maximum DC output current IOUT delivered to load) and short-circuit current, OUT connected to GND IOSRILIM = 61.9 kΩmin 1590 · typ 1785 · max 1960 mA5
Current-limit threshold (Maximum DC output current IOUT delivered to load) and short-circuit current, OUT connected to GND IOSRILIM = 100 kΩmin 935 · typ 1100 · max 1260 mA5
Supply current, low-level output IIN_OFFVIN = 6.5 V, No load on OUT, VEN = 6.5 V or VEN = 0 Vtyp 0.1 · max 2 uA5
Supply current, high-level output IIN_ONVIN = 6.5 V, No load on OUT, RILIM = 24.9 kΩtyp 95 · max 120 uA5
Supply current, high-level output IIN_ONVIN = 6.5 V, No load on OUT, RILIM = 100 kΩtyp 85 · max 110 uA5
Reverse leakage current IREVVOUT = 6.5 V, VIN = 0 V, TJ = 25 °Ctyp 0.01 · max 1 uA5
Low-level input voltage (IN pin) UVLOVIN risingtyp 2.35 · max 2.45 V5
UVLO hysteresis (IN pin)Reference onlytyp 35 mV5
Output low voltage (FAULT pin) VOLIFAULT = 1 mAmax 180 mV5
Off-state leakageVFAULT = 6.5 Vmax 1 uA5
FAULT deglitchFAULT assertion or deassertion due to overcurrent conditionmin 6 · typ 9 · max 13 ms5
Thermal shutdown threshold OTSD2min 155 °C5
Thermal shutdown threshold in current-limit OTSDmin 135 °C5
HysteresisThermal shutdown; reference onlytyp 20 °C5

Pins, by the datasheet

9
1 GND
Ground connection; connect externally to PowerPAD. · p. 3
2 IN
Input voltage; connect a 0.1-uF or greater ceramic capacitor to GND as close to the IC as possible. · p. 3
3 IN
Input voltage; connect a 0.1-uF or greater ceramic capacitor to GND as close to the IC as possible. · p. 3
4 EN
Enable input; logic high turns on the power switch. · p. 3
5 ILIM
External resistor sets the current-limit threshold; recommended RILIM is 20 kΩ to 187 kΩ. · p. 3
6 OUT
Power-switch output. · p. 3
7 OUT
Power-switch output. · p. 3
8 FAULT
Active-low open-drain output asserted during overcurrent or overtemperature conditions. · p. 3
PowerPAD PowerPAD™
Internally connected to GND; heat-sinks the part to circuit-board traces; connect externally to the GND pin. · p. 3

Ordering codes, by the datasheet

9
TPS2557DRBR
SON (DRB) | 8 · 3000 units, LARGE T&R · p. 22
TPS2557DRBR.A
SON (DRB) | 8 · 3000 units, LARGE T&R · p. 22
TPS2557DRBR.B
SON (DRB) | 8 · 3000 units, LARGE T&R · p. 22
TPS2557DRBRG4
SON (DRB) | 8 · 3000 units, LARGE T&R · p. 22
TPS2557DRBRG4.A
SON (DRB) | 8 · 3000 units, LARGE T&R · p. 22
TPS2557DRBRG4.B
SON (DRB) | 8 · 3000 units, LARGE T&R · p. 22
TPS2557DRBT
SON (DRB) | 8 · 250 units, SMALL T&R · p. 22
TPS2557DRBT.A
SON (DRB) | 8 · 250 units, SMALL T&R · p. 22
TPS2557DRBT.B
SON (DRB) | 8 · 250 units, SMALL T&R · p. 22

Open-source boards using it

15See all 15
  • 4 layers65 × 56 mmEWS, the printed circuit board in 3D

    EWS

    eiten/EWS

    Universal 3D-Printer HAT for SBC with CAN-Interface and USB Hub

    124 parts1
  • 2 layers99.1 × 78.7 mmPrototype 1, the printed circuit board in 3D

    Prototype 1

    22Limac/prototype_1

    41 parts
  • 4 layers150 × 120 mmPi usb port switch, the printed circuit board in 3D

    Pi usb port switch

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    197 parts3MIT
  • 4 layers130 × 90 mmRoute, the printed circuit board in 3D

    Route

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    83 parts3MIT
  • 4 layers130 × 90 mmUsb controlled debug hub, the printed circuit board in 3D

    Usb controlled debug hub

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    146 parts3MIT
  • 4 layers130 × 100 mmUsb controlled debug hub, the printed circuit board in 3D

    Usb controlled debug hub

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    172 parts3MIT
  • 4 layers150 × 115 mmUsb controlled debug hub 2a, the printed circuit board in 3D

    Usb controlled debug hub 2a

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    190 parts3MIT
  • 4 layers130 × 100 mmUsb controlled debug hub, the printed circuit board in 3D

    Usb controlled debug hub

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    175 parts3MIT

Questions

Is there a KiCad symbol and footprint for the TPS2557DRB?

Yes. The symbol is EasyEDA_Cloud:TPS2556DRBR and the footprint Package_SON:VSON-8-1EP_3x3mm_P0.65mm_EP1.65x2.4mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS2557DRB?

SON-8(3x3), with 9 pins. Its footprint is drawn on this page.

Where is the TPS2557DRB datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS2557DRB?

JLCPCB lists it as part C130056, with 6,867 in stock; the sellers' links on this page open their listings.

Which open-source boards use the TPS2557DRB?

15 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.