TPS25200DRVR

Texas InstrumentsExtended

-40℃~+125℃ 2.5A 2.5V~6.5V 70mΩ Active High High Side Switch Overvoltage protection、Output discharge function、Soft-start、Under-voltage lockout、Overcurrent Protection、Over temperature protection、Short-Circuit Protection、Reverse current blocking WSON-6-EP(2x2) Power Distribution Switches ROHS

Datasheet JLCPCB LCSC

Part id: ti/TPS25200DRVR
Category: Supervisor And Reset ICs
Package: WSON-6-EP(2x2)
Pins: 6
In stock: 30 at JLCPCB (C128401)
Used on: 11 open-source boards

Overview

The TPS25200DRVR is a supervisor And Reset IC made by Texas Instruments in a WSON-6-EP(2x2) package with 7 pins. -40℃~+125℃ 2.5A 2.5V~6.5V 70mΩ Active High High Side Switch Overvoltage protection、Output discharge function、Soft-start、Under-voltage lockout、Overcurrent Protection、Over temperature protection、Short-Circuit Protection、Reverse current blocking WSON-6-EP(2x2) Power Distribution Switches ROHS.

PCBKit's library has its KiCad symbol (TPS25200DRVR:TPS25200DRVR, from Antmicro) and its footprint (wson-6-1ep-2x2mm-p0-65mm:WSON-6-1EP_2x2mm_P0.65mm, from Antmicro), ready for a KiCad board. 30 are in stock at JLCPCB (part C128401). 11 open-source boards in 8 repositories on GitHub use it.

Symbol

TPS25200DRVR:TPS25200DRVRFrom Antmicro

Footprint

wson-6-1ep-2x2mm-p0-65mm:WSON-6-1EP_2x2mm_P0.65mmFrom Antmicro

From the datasheet

Supply, least: 2.5 V · IN, recommended operating min · p. 4
Supply, most: 6.5 V · IN, recommended operating max · p. 4
Supply, absolute maximum: 20 V · IN, absolute maximum · p. 3
Junction, hottest: 125 °C · Recommended operating junction temperature max · p. 4
Gives: 2.6 A · OUT, continuous output current max · p. 4
Takes working: 143 µA · IN, typical enabled current, VIN = 5V, no load, RILIM = 33kΩ · p. 5
Takes at most: 200 µA · IN, max enabled current, VIN = 5V, no load, RILIM = 33kΩ · p. 5
Takes asleep: 800 nA · IN, typical disabled current, VEN = 0V, VIN = 5V · p. 5
Current limit: 2.952 A · Typical current limit, RILIM = 33kΩ · p. 5
A pin gives at most: 25 mA · FAULT, absolute maximum continuous sink current · p. 3
A pin gives at most: 150 µA · ILIM, absolute maximum continuous source current · p. 3
Junction to air (DRV (WSON)): 66.5 K/W · Junction to ambient thermal resistance · p. 4
Junction to board (DRV (WSON)): 36.1 K/W · Junction to board thermal resistance · p. 4
Junction to case (DRV (WSON)): 83.4 K/W · Junction to case top thermal resistance · p. 4

What it is and has

Device type: 5V eFuse with precision adjustable current limit and overvoltage clamp · p. 1
Input voltage tolerance: 20V · p. 1
Overvoltage shutdown: 7.6V · p. 1
Overvoltage clamp: 5.25V to 5.55V · p. 1
Overvoltage lockout response: 0.6μs · p. 1
Short-circuit response: 3.5μs · p. 1
Integrated power switch: 60mΩ high-side MOSFET · p. 1
Current-limit accuracy: ±6% at 2.9A · p. 1
Protection: Reverse-current blocking when disabled · p. 1
Soft start: Built in · p. 1
Pin compatibility: TPS2553 · p. 1
Approval: UL 2367 · p. 1
Package: DRV, WSON-6, 2mm × 2mm · p. 1

Around it

cap 0.1µF 或更大: between IN and GND; 陶瓷电容器，尽可能靠近 IC。 · p. 3
res 33kΩ ≤ RILIM ≤ 1100kΩ: between ILIM and GND; 接地电阻用于设定电流限制阈值。 · p. 3
res 42.2kΩ: between ILIM and GND; 1% 电阻设计示例，将最小电流限制阈值设定为 2130mA。 · p. 16

Specifications

Parameter	Conditions	As printed	Page
IN 电压	电压以 GND 为基准	min -0.3 · max 20 V	3
OUT、EN、ILIM、FAULT 上的电压	电压以 GND 为基准	min -0.3 · max 7 V	3
电压范围为 IN 至 OUT		min -7 · max 20 V	3
连续 FAULT 输出灌电流		max 25 mA	3
连续 ILIM 输出拉电流		max 150 uA	3
贮存温度 Tstg		min -65 · max 150 °C	3
静电放电 V(ESD)	人体放电模型 (HBM)，符合 ANSI/ESDA/JEDEC JS-001 标准	min -2000 · max 2000 V	3
静电放电 V(ESD)	充电器件模型 (CDM)，符合 JEDEC 规范 JESD22-C101	min -500 · max 500 V	3
输入电压 IN VIN		min 2.5 · max 6.5 V	4
启用端子电压 VEN		min 0 · max 6.5 V	4
连续 FAULT 灌电流 IFAULT		min 0 · max 10 mA	4
持续输出电流 OUT IOUT		max 2.6 A	4
电流限制设置电阻器 RILIM		min 33 · max 1100 kΩ	4
工作结温 TJ		min -40 · max 125 °C	4
结至环境热阻 θJA	TPS25200, DRV (WSON), 6 引脚	typ 66.5 °C/W	4
结至外壳（顶部）热阻 θJCtop	TPS25200, DRV (WSON), 6 引脚	typ 83.4 °C/W	4
结至电路板热阻 θJB	TPS25200, DRV (WSON), 6 引脚	typ 36.1 °C/W	4
结至顶部特征参数 ψJT	TPS25200, DRV (WSON), 6 引脚	typ 1.6 °C/W	4
结至电路板特征参数 ψJB	TPS25200, DRV (WSON), 6 引脚	typ 36.5 °C/W	4
结至外壳（底部）热阻 θJCbot	TPS25200, DRV (WSON), 6 引脚	typ 7.6 °C/W	4
IN–OUT 电阻(1) rDS(on)	2.5V ≤ VIN ≤ 5V，IOUT = 2.5A，TJ = 25°C	typ 60 · max 70 mΩ	4
IN–OUT 电阻(1) rDS(on)	2.5V ≤ VIN ≤ 5V，IOUT = 2.5A，–40°C ≤ TJ ≤ +85°C	typ 60 · max 90 mΩ	4
IN–OUT 电阻(1) rDS(on)	2.5V ≤ VIN ≤ 5V，IOUT = 2.5A，–40°C ≤ TJ ≤ +125°C	typ 60 · max 99 mΩ	4
EN 端子导通阈值	输入上升	max 1.9 V	4
EN 端子关断阈值	输入下降	min 0.6 V	4
迟滞	使能输入 EN；仅供参考	typ 330 mV	4
漏电流 IEN	VEN = 0V 或 5.5V	min -2 · max 2 uA	4
OUT 放电电阻 RDCHG	VOUT = 5V，VEN = 0V	typ 480 · max 625 Ω	4
电流限制，请参阅图 6-4 IOS	RILIM = 33kΩ	min 2773 · typ 2952 · max 3127 mA	5
电流限制，请参阅图 6-4 IOS	RILIM = 40.2kΩ	min 2270 · typ 2423 · max 2570 mA	5
电流限制，请参阅图 6-4 IOS	RILIM = 56kΩ	min 1620 · typ 1740 · max 1860 mA	5
电流限制，请参阅图 6-4 IOS	RILIM = 80.6kΩ	min 1110 · typ 1206 · max 1300 mA	5
电流限制，请参阅图 6-4 IOS	RILIM = 150kΩ	min 590 · typ 647 · max 710 mA	5
电流限制，请参阅图 6-4 IOS	RILIM = 1100kΩ	min 40 · typ 83 · max 130 mA	5
IN 上升 OVLO 阈值电压 V(OVLO)	IN 上升	min 6.8 · typ 7.6 · max 8.45 V	5
迟滞	过压锁定，IN；仅供参考	typ 70 mV	5
OUT 钳位电压阈值 V(OVC)	CL = 1uF、RL = 100Ω、VIN = 6.5V	min 5.25 · typ 5.4 · max 5.55 V	5
电源电流、低电平输出 IIN(off)	VEN = 0V，VIN = 5V	typ 0.8 · max 5 uA	5
电源电流、低电平输出 IIN(off)	VEN = 0V 或 5V、VIN = 20V	typ 1000 · max 1700 uA	5
电源电流、高电平输出 IIN(on)	VIN = 5V，OUT 上无负载，RILIM = 33kΩ	typ 143 · max 200 uA	5
电源电流、高电平输出 IIN(on)	VIN = 5V，OUT 上无负载，RILIM = 150kΩ	typ 134 · max 190 uA	5
反向漏电流 IREV	VOUT = 6.5V，VIN = VEN = 0V，TJ = 25°C，测量 IOUT	typ 3 · max 5 uA	5
IN 上升 UVLO 阈值电压 VUVLO	IN 上升	typ 2.35 · max 2.45 V	5
迟滞	欠压锁定，IN；仅供参考	typ 30 mV	5
输出低电压，FAULT VOL	IFAULT = 1mA	typ 50 · max 180 mV	5
关断状态泄漏	VFAULT = 6.5V	max 1 uA	5
热关断阈值温度，OTSD2		min 155 °C	5
仅电流限制时的热关断阈值，OTSD1	仅电流限制时	min 135 °C	5
迟滞	热关断；仅供参考	typ 20 °C	5

Pins, by the datasheet

1 OUT: 受保护的电源开关 VOUT。 · p. 3
2 ILIM: 连接设定电流限制阈值的外部电阻器；建议 33kΩ ≤ RILIM ≤ 1100kΩ。 · p. 3
3 FAULT: 低电平有效故障输出，在过流、过压或过热时置位；连接上拉电阻器至逻辑 I/O 电压。 · p. 3
4 EN: 高电平启用、低电平关闭；不能悬空，连接 VIN 时必须限制在绝对最大额定值以下。 · p. 3
5 GND: 接地连接；从外部连接至 PowerPAD。 · p. 3
6 IN: 输入电压；在 IN 与 GND 之间靠近 IC 连接 0.1uF 或更大的陶瓷电容器。 · p. 3
PAD PowerPAD™: 内部连接至 GND，用于向电路板散热；从外部连接到 GND 端子。 · p. 3

Ordering codes, by the datasheet

TPS25200DRVR: WSON (DRV) | 6 · 3000 | LARGE T&R; -40 to 125°C · p. 23
TPS25200DRVR.A: WSON (DRV) | 6 · 3000 | LARGE T&R; -40 to 125°C · p. 23
TPS25200DRVRG4: WSON (DRV) | 6 · 3000 | LARGE T&R; -40 to 125°C · p. 23
TPS25200DRVRG4.A: WSON (DRV) | 6 · 3000 | LARGE T&R; -40 to 125°C · p. 23
TPS25200DRVT: WSON (DRV) | 6 · 250 | SMALL T&R; -40 to 125°C · p. 23
TPS25200DRVT.A: WSON (DRV) | 6 · 250 | SMALL T&R; -40 to 125°C · p. 23

Parameters

Control Input Logic: Active High
Current - Supply(Max): 200uA
Current Limit: 2.952A
Features: Short-Circuit Protection
Junction Temperature(Max): 125℃
Maximum Continuous Current: 2.5A
Operating Temperature -: -40℃~+125℃
Output Current: 2.6A
Output Current per Pin(Max): 25mA
Quiescent Current: 143uA
RDS(on): 70mΩ
Standby Current: 800nA
Thermal Resistance(Junction to Ambient): 66.5℃/W
Thermal Resistance(Junction to Board): 36.1℃/W
Thermal Resistance(Junction to Case): 83.4℃/W
Type: High Side Switch
Voltage - Supply: 2.5V~6.5V
Voltage - Supply(Absolute Max): 20V

Order codes

TPS25200DRVRLCSC C128401

Pinout

The pins of the TPS25200DRVR
Pin	Name	Type
1	OUT	Power out
2	ILIM	Output
3	FAULT	Output
4	EN	Input
5	GND	Power in
6	IN	Power in
7	EP	Passive

Show this part on your page

<iframe src="https://pcbkit.io/embed/parts/ti/TPS25200DRVR" title="TPS25200DRVR in PCBKit" width="100%" height="480" style="border:0;border-radius:12px" allow="fullscreen" loading="lazy"></iframe>

For any web page: the part itself, turned and zoomed by the reader.

Open-source boards using it

11See all 11

2 layers92 × 92 mm
Sanket 4.0
Student-Satellite-IITB/Communication-Subsystem
Communication Subsystem for IITBSSP CubeSat Mission
52 parts3
2 layers40 × 43 mm
SlimeVR pcb
H3wastooshort/slimeinator

71 parts2AGPL-3.0
8 layers74 × 128 mm
Limejig
taskx6004/limejig
Open-source LimeJig fixture firmware, host tools, KiCad source, and synthetic test examples
92 parts1MIT
4 layers78.5 × 59 mm
Syncro mainboard
deadbandlabs/syncro-mainboard
Hardware Design for Syncro FFB Interceptor
158 partsCERN-OHL-W-2.0
4 layers64.8 × 62.7 mm
Timer 555
fstp/computer_clock_module
The clock module for my PCB computer
47 parts
2 layers46.9 × 34.3 mm
Mcu board backup20260115
fstp/mcu_board
Just a project for me to learn some PCB design
34 partsMIT
2 layers98.1 × 30.4 mm
3v3-regulator
icarofcb/3.3V-Car-Voltage-Regulator-Grade-board
3.3V Car Voltage Regulator Grade board hardware
41 parts
4 layers128 × 68 mm
EENLD main
light655/EENight_light_dance
Don't try this at home.
136 parts

Questions

Is there a KiCad symbol and footprint for the TPS25200DRVR?

Yes. The symbol is TPS25200DRVR:TPS25200DRVR and the footprint wson-6-1ep-2x2mm-p0-65mm:WSON-6-1EP_2x2mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS25200DRVR?

WSON-6-EP(2x2), with 7 pins. Its footprint is drawn on this page.

Where is the TPS25200DRVR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS25200DRVR?

JLCPCB lists it as part C128401, with 30 in stock; the sellers' links on this page open their listings.

Which open-source boards use the TPS25200DRVR?

11 boards in 8 repositories on GitHub; the most starred are listed on this page, with their KiCad files.