
TPA3118D2DAPR
Texas InstrumentsExtended
-40℃~+85℃ -70dB 0.1% 102dB 2-Channel 30Wx2@8Ω 4.5V~26V 50mA 90% Class D Enable/shutdown function、Filterless architecture、ESD protection、Overvoltage protection、Analog voltage gain、Integrated PLL HTSSOP-32-EP-6.1mm Audio Amplifiers ROHS
- Part id
- ti/TPA3118D2DAPR
- Category
- Audio Amplifiers
- Package
- HTSSOP-32-EP-6.1mm
- Pins
- 33
- In stock
- 32,394 at JLCPCB (C46497)
- Used on
- 7 open-source boards
Overview
The TPA3118D2DAPR is an audio Amplifier made by Texas Instruments in a HTSSOP-32-EP-6.1mm package with 33 pins. -40℃~+85℃ -70dB 0.1% 102dB 2-Channel 30Wx2@8Ω 4.5V~26V 50mA 90% Class D Enable/shutdown function、Filterless architecture、ESD protection、Overvoltage protection、Analog voltage gain、Integrated PLL HTSSOP-32-EP-6.1mm Audio Amplifiers ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:AW83118TSR, from EasyEDA) and its footprint (EasyEDA_Cloud:HTSSOP-32_L11.0-W6.1-P0.65-LS8.1-BL-EP, from EasyEDA), ready for a KiCad board. 32,394 are in stock at JLCPCB (part C46497). 7 open-source boards in 6 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
17- Supply, least
- 4.5 V · PVCC, AVCC, recommended operating min · p. 5
- Supply, most
- 26 V · PVCC, AVCC, recommended operating max · p. 5
- Supply, absolute maximum
- 30 V · PVCC, AVCC, absolute max · p. 5
- Works from
- -40 °C · Operating free-air temperature min · p. 5
- Works up to
- 85 °C · Operating free-air temperature max · p. 5
- Junction, hottest
- 150 °C · Operating junction temperature max · p. 5
- Takes working
- 20 mA · Quiescent supply current typical, PVCC = 12 V, outputs enabled, no load or filter · p. 6
- Takes working
- 32 mA · Quiescent supply current typical, PVCC = 24 V, outputs enabled, no load or filter · p. 6
- Takes asleep
- 50 µA · Shutdown supply current typical, PVCC = 24 V · p. 6
- Current limit
- 7.5 A · Over current trip point typical · p. 7
- Junction to air (DAP)
- 22 K/W · Junction-to-ambient thermal resistance · p. 6
- Junction to board (DAP)
- 4.7 K/W · Junction-to-board characterization parameter ψJB · p. 6
- Switches at
- 400 kHz · Oscillator frequency typical, AM2=0, AM1=0, AM0=0 · p. 7
- Switches at
- 500 kHz · Oscillator frequency typical, AM2=0, AM1=0, AM0=1 · p. 7
- Switches at
- 600 kHz · Oscillator frequency typical, AM2=0, AM1=1, AM0=0 · p. 7
- Switches at
- 1 MHz · Oscillator frequency typical, AM2=0, AM1=1, AM0=1 · p. 7
- Switches at
- 1.2 MHz · Oscillator frequency typical, AM2=1, AM1=0, AM0=0 · p. 7
What it is and has
6- Amplifier architecture
- Class-D · p. 1
- Supply voltage range
- 4.5 V to 26 V · p. 1
- Power limit
- Programmable · p. 1
- Audio inputs
- Differential and single-ended · p. 1
- Synchronization
- Master and Slave · p. 1
- Package
- DAP, 32-pin HTSSOP Pad Down · p. 1
Around it
35- cap 1 µF
- between GVDD and GND; X5R ceramic decoupling capacitor; GVDD is not an external supply. · p. 16
- cap 220 nF
- between BSNL and OUTNL; X5R or better ceramic bootstrap capacitor, rated at least 16 V. · p. 4
- cap 220 nF
- between BSPL and OUTPL; X5R or better ceramic bootstrap capacitor, rated at least 16 V. · p. 4
- cap 220 nF
- between BSNR and OUTNR; X5R or better ceramic bootstrap capacitor, rated at least 16 V. · p. 4
- cap 220 nF
- between BSPR and OUTPR; X5R or better ceramic bootstrap capacitor, rated at least 16 V. · p. 4
- cap 1 µF
- between PLIMIT and GND; Ensures stability of the power limit circuit. · p. 15
- cap 1.5 µF
- between Audio source and Audio input; Recommended input AC coupling at 20 dB gain; 60 kΩ input impedance, 1.8 Hz high-pass filter. Use low-leakage capacitors; polarized positive terminal faces the input. · p. 14
- cap 3.3 µF
- between Audio source and Audio input; Recommended input AC coupling at 26 dB gain; 30 kΩ input impedance, 1.6 Hz high-pass filter. · p. 14
- cap 5.6 µF
- between Audio source and Audio input; Recommended input AC coupling at 32 dB gain; 15 kΩ input impedance, 1.9 Hz high-pass filter. · p. 14
- cap 10 µF
- between Audio source and Audio input; Recommended input AC coupling at 36 dB gain; 9 kΩ input impedance, 1.8 Hz high-pass filter. · p. 14
- res 5.6 kΩ
- between GAIN/SLV and GND; Master, 20 dB gain; R2 to GVDD open. Resistor tolerance 5% or better. · p. 14
- res 20 kΩ
- between GAIN/SLV and GND; Master, 26 dB gain; resistor tolerance 5% or better. · p. 14
- res 100 kΩ
- between GAIN/SLV and GVDD; Master, 26 dB gain; resistor tolerance 5% or better. · p. 14
- res 39 kΩ
- between GAIN/SLV and GND; Master, 32 dB gain; resistor tolerance 5% or better. · p. 14
- res 100 kΩ
- between GAIN/SLV and GVDD; Master, 32 dB gain; resistor tolerance 5% or better. · p. 14
- res 47 kΩ
- between GAIN/SLV and GND; Master, 36 dB gain; resistor tolerance 5% or better. · p. 14
- res 75 kΩ
- between GAIN/SLV and GVDD; Master, 36 dB gain; resistor tolerance 5% or better. · p. 14
- res 51 kΩ
- between GAIN/SLV and GND; Slave, 20 dB gain; resistor tolerance 5% or better. · p. 14
- res 75 kΩ
- between GAIN/SLV and GND; Slave, 26 dB gain; resistor tolerance 5% or better. · p. 14
- res 47 kΩ
- between GAIN/SLV and GVDD; Slave, 26 dB gain; resistor tolerance 5% or better. · p. 14
- res 100 kΩ
- between GAIN/SLV and GND; Slave, 32 dB gain; resistor tolerance 5% or better. · p. 14
- res 39 kΩ
- between GAIN/SLV and GVDD; Slave, 32 dB gain; resistor tolerance 5% or better. · p. 14
- res 100 kΩ
- between GAIN/SLV and GND; Slave, 36 dB gain; resistor tolerance 5% or better. · p. 14
- res 16 kΩ
- between GAIN/SLV and GVDD; Slave, 36 dB gain; resistor tolerance 5% or better. · p. 14
- res 45 kΩ
- between PLIMIT and GND; Power limit example: PVCC 24 V, PLIMIT 3.3 V, output 12.67 Vrms; EVM gain 26 dB, input 1 Vrms. · p. 16
- res 51 kΩ
- between PLIMIT and GVDD; Power limit example: PVCC 24 V, PLIMIT 3.3 V, output 12.67 Vrms. · p. 16
- res 24 kΩ
- between PLIMIT and GND; Power limit example: PVCC 24 V, PLIMIT 2.25 V, output 9 Vrms. · p. 16
- res 51 kΩ
- between PLIMIT and GVDD; Power limit example: PVCC 24 V, PLIMIT 2.25 V, output 9 Vrms. · p. 16
- res 24 kΩ
- between PLIMIT and GND; Power limit example: PVCC 12 V, PLIMIT 2.25 V, output 9 Vrms. · p. 16
- res 51 kΩ
- between PLIMIT and GVDD; Power limit example: PVCC 12 V, PLIMIT 2.25 V, output 9 Vrms. · p. 16
- res 18 kΩ
- between PLIMIT and GND; Power limit example: PVCC 12 V, PLIMIT 1.5 V, output 6.3 Vrms. · p. 16
- res 68 kΩ
- between PLIMIT and GVDD; Power limit example: PVCC 12 V, PLIMIT 1.5 V, output 6.3 Vrms. · p. 16
- res 100 kΩ
- between Logic source and Logic input; Series resistor needed for AM0, AM1, AM2, MUTE, SDZ, MODSEL if the maximum slew rate is exceeded. · p. 5
- res 18 Ω
- between Class-D output and Snubber capacitor; Suggested series RC snubber from each output to ground; application-specific design and tight layout returning directly to IC GND. · p. 21
- cap 330 pF
- between Snubber resistor and GND; Suggested series RC snubber with 18 Ω from each class-D output to ground; application-specific design. · p. 21
Specifications
53| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage VCC | PVCC, AVCC | min -0.3 · max 30 V | 5 |
| Input voltage VI | INPL, INNL, INPR, INNR | min -0.3 · max 6.3 V | 5 |
| Input voltage VI | PLIMIT, GAIN / SLV, SYNC; maximum GVDD+0.3 V | min -0.3 V | 5 |
| Input voltage VI | AM0, AM1, AM2, MUTE, SDZ, MODSEL; maximum PVCC+0.3 V | min -0.3 V | 5 |
| Slew rate, maximum | AM0, AM1, AM2, MUTE, SDZ, MODSEL | max 10 V/ms | 5 |
| Operating free-air temperature TA | min -40 · max 85 °C | 5 | |
| Operating junction temperature TJ | min -40 · max 150 °C | 5 | |
| Storage temperature Tstg | min -40 · max 125 °C | 5 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; value ±2000 V | min -2000 · max 2000 V | 5 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; value ±500 V | min -500 · max 500 V | 5 |
| Supply voltage VCC | PVCC, AVCC | min 4.5 · max 26 V | 5 |
| High-level input voltage VIH | AM0, AM1, AM2, MUTE, SDZ, SYNC, MODSEL | min 2 V | 5 |
| Low-level input voltage VIL | AM0, AM1, AM2, MUTE, SDZ, SYNC, MODSEL | max 0.8 V | 5 |
| Low-level output voltage VOL | FAULTZ, RPULL-UP = 100 kΩ, PVCC = 26 V | max 0.8 V | 5 |
| High-level input current IIH | AM0, AM1, AM2, MUTE, SDZ, MODSEL (VI = 2 V, VCC = 18 V) | max 50 uA | 5 |
| Minimum load Impedance RL(BTL) | TPA3118D2; Output filter: L = 10 uH, C = 680 nF; NOM = 4 Ω | min 3.2 · typ 4 Ω | 5 |
| Minimum load Impedance RL(PBTL) | TPA3118D2; Output filter: L = 10 uH, C = 1 uF | min 1.6 Ω | 5 |
| Output-filter Inductance Lo | Minimum output filter inductance under short-circuit condition | min 1 uH | 5 |
| Junction-to-ambient thermal resistance RθJA | TPA3118D2, DAP, 32 PINS; TPA3118D2EVM PCB layout | typ 22 °C/W | 6 |
| Junction-to-top characterization parameter ψJT | TPA3118D2, DAP, 32 PINS; TPA3118D2EVM PCB layout | typ 0.3 °C/W | 6 |
| Junction-to-board characterization parameter ψJB | TPA3118D2, DAP, 32 PINS; TPA3118D2EVM PCB layout | typ 4.7 °C/W | 6 |
| Class-D output offset voltage (measured differentially) | VOS | | TA = 25°C, AVCC = PVCC = 12 V to 24 V, RL = 4 Ω; VI = 0 V, Gain = 36 dB | typ 1.5 · max 15 mV | 6 |
| Quiescent supply current ICC | TA = 25°C; SDZ = 2 V, No load or filter, PVCC = 12 V | typ 20 · max 35 mA | 6 |
| Quiescent supply current ICC | TA = 25°C; SDZ = 2 V, No load or filter, PVCC = 24 V | typ 32 · max 50 mA | 6 |
| Quiescent supply current in shutdown mode ICC(SD) | TA = 25°C; SDZ = 0.8 V, No load or filter, PVCC = 24 V | typ 50 · max 400 uA | 6 |
| Drain-source on-state resistance, measured pin to pin rDS(on) | PVCC = 21 V, Iout = 500 mA, TJ = 25°C | typ 120 mΩ | 6 |
| Gain (BTL) G | R1 = 5.6 kΩ, R2 = Open | min 19 · typ 20 · max 21 dB | 6 |
| Gain (BTL) G | R1 = 20 kΩ, R2 = 100 kΩ | min 25 · typ 26 · max 27 dB | 6 |
| Gain (BTL) G | R1 = 39 kΩ, R2 = 100 kΩ | min 31 · typ 32 · max 33 dB | 6 |
| Gain (BTL) G | R1 = 47 kΩ, R2 = 75 kΩ | min 35 · typ 36 · max 37 dB | 6 |
| Gain (SLV) G | R1 = 51 kΩ, R2 = 51 kΩ | min 19 · typ 20 · max 21 dB | 6 |
| Gain (SLV) G | R1 = 75 kΩ, R2 = 47 kΩ | min 25 · typ 26 · max 27 dB | 6 |
| Gain (SLV) G | R1 = 100 kΩ, R2 = 39 kΩ | min 31 · typ 32 · max 33 dB | 6 |
| Gain (SLV) G | R1 = 100 kΩ, R2 = 16 kΩ | min 35 · typ 36 · max 37 dB | 6 |
| Turn-on time ton | SDZ = 2 V | typ 10 ms | 6 |
| Turn-off time tOFF | SDZ = 0.8 V | typ 2 us | 6 |
| Gate drive supply GVDD | IGVDD < 200 uA | min 6.4 · typ 6.9 · max 7.4 V | 6 |
| Output voltage maximum under PLIMIT control VO | V(PLIMIT) = 2 V; VI = 1 Vrms | min 6.75 · typ 7.9 · max 8.75 V | 6 |
| Power supply ripple rejection KSVR | TA = 25°C, AVCC = PVCC = 12 V to 24 V, RL = 4 Ω; 200 mVPP ripple at 1 kHz, Gain = 20 dB, Inputs AC-coupled to GND | typ -70 dB | 7 |
| Continuous output power PO | TA = 25°C, RL = 4 Ω; THD+N = 10%, f = 1 kHz, PVCC = 14.4 V | typ 25 W | 7 |
| Continuous output power PO | TA = 25°C, RL = 4 Ω; THD+N = 10%, f = 1 kHz, PVCC = 21 V | typ 50 W | 7 |
| Total harmonic distortion + noise THD+N | VCC = 21 V, f = 1 kHz, PO = 25 W (half-power), TA = 25°C, RL = 4 Ω | typ 0.1 % | 7 |
| Output integrated noise Vn | 20 Hz to 22 kHz, A-weighted filter, Gain = 20 dB | typ 65 uV | 7 |
| Output integrated noise Vn | 20 Hz to 22 kHz, A-weighted filter, Gain = 20 dB | typ -80 dBV | 7 |
| Crosstalk | VO = 1 Vrms, Gain = 20 dB, f = 1 kHz | typ -100 dB | 7 |
| Signal-to-noise ratio SNR | Maximum output at THD+N < 1%, f = 1 kHz, Gain = 20 dB, A-weighted | typ 102 dB | 7 |
| Oscillator frequency fOSC | AM2=0, AM1=0, AM0=0 | min 376 · typ 400 · max 424 kHz | 7 |
| Oscillator frequency fOSC | AM2=0, AM1=0, AM0=1 | min 470 · typ 500 · max 530 kHz | 7 |
| Oscillator frequency fOSC | AM2=0, AM1=1, AM0=0 | min 564 · typ 600 · max 636 kHz | 7 |
| Oscillator frequency fOSC | AM2=0, AM1=1, AM0=1 | min 940 · typ 1000 · max 1060 kHz | 7 |
| Oscillator frequency fOSC | AM2=1, AM1=0, AM0=0 | min 1128 · typ 1200 · max 1278 kHz | 7 |
| Thermal hysteresis | typ 15 °C | 7 | |
| Over current trip point | TPA3118D2 | typ 7.5 A | 7 |
Pins, by the datasheet
33- 1 MODSEL
- Mode selection: LOW = BD mode, HIGH = 1 SPW mode; TTL levels compliant with AVCC. · p. 4
- 2 SDZ
- Shutdown: LOW = outputs Hi-Z, HIGH = outputs enabled; TTL levels compliant with AVCC. · p. 4
- 3 FAULTZ
- General fault reporting including overtemperature and DC detect; high = normal, low = fault. · p. 4
- 4 RINP
- Positive right-channel audio input, biased at 3 V. · p. 4
- 5 RINN
- Negative right-channel audio input, biased at 3 V. · p. 4
- 6 PLIMIT
- Power limit adjustment; connect a divider from GVDD to GND, or connect directly to GVDD for no power limit. · p. 4
- 7 GVDD
- Internally generated gate supply; connect only a 1 uF X7R ceramic decoupling capacitor and PLIMIT and GAIN/SLV dividers. · p. 4
- 8 GAIN/SLV
- Voltage divider selects gain and Master or Slave mode. · p. 4
- 9 GND
- Ground. · p. 4
- 10 LINP
- Positive left-channel audio input, biased at 3 V; connect to GND for PBTL mode. · p. 4
- 11 LINN
- Negative left-channel audio input, biased at 3 V; connect to GND for PBTL mode. · p. 4
- 12 MUTE
- Fast output disable/enable: HIGH = Hi-Z, LOW = enabled; TTL levels compliant with AVCC. · p. 4
- 13 AM2
- AM Avoidance Frequency Selection. · p. 4
- 14 AM1
- AM Avoidance Frequency Selection. · p. 4
- 15 AM0
- AM Avoidance Frequency Selection. · p. 4
- 16 SYNC
- Clock input/output for synchronizing multiple class-D devices; direction determined by GAIN/SLV. · p. 4
- 17 AVCC
- Analog Supply. · p. 4
- 18 PVCC
- Power supply. · p. 4
- 19 PVCC
- Power supply. · p. 4
- 20 BSNL
- Negative left-channel bootstrap; connect a 220 nF X5R or better ceramic capacitor to OUTNL. · p. 4
- 21 OUTNL
- Negative left-channel output. · p. 4
- 22 GND
- Ground. · p. 4
- 23 OUTPL
- Positive left-channel output. · p. 4
- 24 BSPL
- Positive left-channel bootstrap; connect a 220 nF X5R or better ceramic capacitor to OUTPL. · p. 4
- 25 GND
- Ground. · p. 4
- 26 BSNR
- Negative right-channel bootstrap; connect a 220 nF X5R or better ceramic capacitor to OUTNR. · p. 4
- 27 OUTNR
- Negative right-channel output. · p. 4
- 28 GND
- Ground. · p. 4
- 29 OUTPR
- Positive right-channel output. · p. 4
- 30 BSPR
- Positive right-channel bootstrap; connect a 220 nF X5R or better ceramic capacitor to OUTPR. · p. 4
- 31 PVCC
- Power supply. · p. 4
- 32 PVCC
- Power supply. · p. 4
- 33 PowerPAD
- Connect to GND for best performance; otherwise leave floating. · p. 4
Open-source boards using it
7- 2 layers100 × 60 mm

- 4 layers130 × 105 mm

HomeDeck
Kilan777/HomeDeck
Jarvis HomeDeck: a Raspberry Pi CM4 carrier board and voice-assistant software for a 7-inch smart display (KiCad hardware, generated from Python, plus the Python/JS assistant)
228 parts1 - 4 layers90 × 56.5 mm

- 4 layers100 × 100 mm

NotSmart Speaker
BBroadbent/NotSmart-Speaker
A open-hardware, local-first "dumb" smart speaker powered by an ESP32, PCM5100A DAC, TPA3118 Class-D amp, and 20V USB-PD.
102 parts - 4 layers175 × 135 mm

- 2 layers98 × 98 mm

Rev1 Power Board
B1narySolutions/amp-hardware
Monorepo for our capstone team's PCBs and housing
67 parts - 2 layers53.6 × 36.8 mm

Parts like it
8TPA3126D2DAD
HTSSOP-32-EP-6.1mm-40℃~+85℃ -70dB 0.1% 102dB 15mA 2 Pairs Differential Inputs 2-Channel 4.5V~26V 50W×2@4Ω 90% Automatic mute/no-noise switch、Enable/shutdown function、ESD Protection、Overvoltage Protection、Analog voltage gain Class D HTSSOP-32-EP-6.1mm Audio Amplifiers ROHSTexas InstrumentsAudio AmplifiersTPA3128D2DAPR
HTSSOP-32-EP-6.1mm-40℃~+85℃ -70dB 0.1% 102dB 2 Pairs Differential Inputs 2-Channel 23mA 30W×2@8Ω 4.5V~26V 90% Class D Enable/shutdown function、ESD protection、Overvoltage protection、Analog voltage gain、Integrated PLL HTSSOP-32-EP-6.1mm Audio Amplifiers ROHSTexas InstrumentsAudio AmplifiersTPA3130D2DAPR
HTSSOP-32-EP-6.1mm-40℃~+85℃ -70dB 0.1% 102dB 15Wx2@8Ω 2-Channel 35mA 4.5V~26V 90% Class D Enable/shutdown function、Filterless architecture、ESD protection、Overvoltage protection、Integrated PLL HTSSOP-32-EP-6.1mm Audio Amplifiers ROHSTexas InstrumentsAudio AmplifiersTAS5102DADR
HTSSOP-32-EP-6.1mm0.05% 0℃~+70℃ 105dB 2-Channel 20Wx2@8Ω 6.3mA 8V~23V 90% Automatic mute/no-noise switch、Overvoltage protection Class D HTSSOP-32-EP-6.1mm Audio Amplifiers ROHSTexas InstrumentsAudio AmplifiersTPA3128D2DAP
HTSSOP-32-40℃~+85℃ 2-Channel 30Wx2@8Ω 4.5V~26V Overvoltage protection、Integrated PLL HTSSOP-32 Audio Amplifiers ROHSTexas InstrumentsAudio AmplifiersTAS5103DAPR
HTSSOP-32-EP-6.1mm0.05% 0℃~+70℃ 105dB 15Wx2@8Ω 2-Channel 50mA 8V~23V 90% Automatic mute/no-noise switch、Overvoltage protection Class D HTSSOP-32-EP-6.1mm Audio Amplifiers ROHSTexas InstrumentsAudio AmplifiersTAS5760MDAP
HTSSOP-32-EP-6.1mm-25℃~+85℃ 0.03% 105dB 2-Channel 20W×2@8Ω 4.5V~24V Class D Digitally programmable gain、Built-in audio processing、Integrated PLL HTSSOP-32-EP-6.1mm Audio Amplifiers ROHSTexas InstrumentsAudio AmplifiersTPA2000D4DAP
HTSSOP-32-EP-6.1mm-40℃~+85℃ -75dB、-70dB 0.2%、0.4% 2-Channel 3.7V~5.5V 80dB、85dB Automatic mute/no-noise switch、Enable/shutdown function、Filterless architecture、Digitally programmable gain Class AB、Class D HTSSOP-32-EP-6.1mm Audio Amplifiers ROHSTexas InstrumentsAudio Amplifiers
Questions
Is there a KiCad symbol and footprint for the TPA3118D2DAPR?
Yes. The symbol is EasyEDA_Cloud:AW83118TSR and the footprint EasyEDA_Cloud:HTSSOP-32_L11.0-W6.1-P0.65-LS8.1-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TPA3118D2DAPR?
HTSSOP-32-EP-6.1mm, with 33 pins. Its footprint is drawn on this page.
Where is the TPA3118D2DAPR datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TPA3118D2DAPR?
JLCPCB lists it as part C46497, with 32,394 in stock; the sellers' links on this page open their listings.
What can replace the TPA3118D2DAPR?
Parts like it in the library: the TPA3126D2DAD by Texas Instruments, the TPA3128D2DAPR by Texas Instruments, the TPA3130D2DAPR by Texas Instruments and the TAS5102DADR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TPA3118D2DAPR?
7 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.