Skip to the content
4 layers90 × 56.5 mmSeed3-carrier, the printed circuit board in 3D

Monorepo for our capstone team's PCBs and housing

Size
90 × 56.5 mm
Copper layers
4
Thickness
1.6 mm
Parts
127
Nets
97
Pads
349
Tracks, vias
212, 215
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
25 Oct 2026
Updated
7 Nov 2026

Overview

Seed3-carrier is an open-source printed circuit board by B1narySolutions, from the B1narySolutions/amp-hardware repository on GitHub. It is a 4-layer board of 90 × 56.5 mm with 127 parts on 97 nets, routed with 212 tracks and 215 vias.

It is built around the TLV9061QDBVRQ1, MAX9722AEUE+ and TPA3118D2DAPR, with the PESD5V0S1BAF, RC0805FR-0710KL and C1206C104K5RACTU among its other parts. Its parts include 39 capacitors, 38 resistors, 9 connectors, 6 diodes and 4 ICs.

Main components

12

README

power-board/README.md

Power board

This directory holds the power board's KiCad project, rev 1 (Rev1_Power_Board.kicad_pro).

What the audio board needs from it

The audio board (../audio-board/rev2/) connects to the power board through two screw terminals, six wires in all. This list collects everything the audio board expects from the power board, and it is the contract between the two boards. ../audio-board/rev2/DESIGN.md gives the reasons ("Power board connector (J6)", "Output mute", "Speaker send", "Display connector (J3)", "What each connector can see"). If the power board's design departs from any number here, change it here and in the audio board's DESIGN.md together, and review both boards' designs against the new number.

The contract in brief

SignalDriven byPromise
5V (J6.1)Power board4.75–5.25 V (5.0 V ± 5 %), never above 5.5 V
BAT (J6.3)Power board0–3.3 V, source impedance 10 kΩ or less
MUTE (J6.4)Power board pulls up, audio board pulls downPull-up of 4.7 kΩ or more to at most the 5 V rail; the audio board pulls it to ≈ 0.24–0.5 V to play
LINE+ (J5.1)Audio boardAudio, full scale ≈ 1 Vrms (1.5 V peak), ≈ 0 V DC, from ≈ 1 kΩ (at most 1.1 kΩ)
LINE− (J5.2)Audio boardThe audio board's ground through ≈ 1 kΩ (0 V ± 10 mV)
LINE+ / LINE− loadPower board10 kΩ–1 MΩ per leg

Connections

Audio board terminalPins (silkscreen)What the power board does with it
J6, power1 5V, 2 GND, 3 BAT, 4 MUTESends 5 V and the battery level to the audio board, and gets the speaker mute back
J5, speaker send1 LINE+, 2 LINE−Feeds the speaker amp's differential input

Both are 3.5 mm screw terminals on the audio board, J6 4-way and J5 2-way. Seen from the wire side, J6 reads 5V, GND, BAT, MUTE from left to right.

The audio board's third screw terminal, J3 (1 GND, 2 TX, 3 RX), is not a power board connection. It is the UART link between the Seed3 and the display's ESP32-S3, wired straight to the display. The power board only supplies the display's power (see "Display").

5 V supply (J6.1, J6.2)

  • 5.0 V ± 5 % (4.75–5.25 V) at J6, never above 5.5 V: the audio board's op-amp (U1) and headphone amp (U2) run straight from it. The audio board's Q1 drops tens of mV, and its firmware won't start audio below 4.7 V or keep it running below 4.4 V.
  • The audio board draws well under 1 A. The Daisy takes roughly 100–200 mA.
  • One 5 V wire and one GND wire on J6 (a Phoenix PT 1,5 contact is rated 17.5 A). The display's ground returns with its own power pair, though some of its return current comes back through the display UART's GND (J3) and across to J6, which sit side by side on the audio board.
  • The audio board has reverse-polarity protection (Q1), but nothing else on the power board should rely on it.

Power switch and battery

  • The battery: a Talentcell rechargeable power bank, "72W 100Wh 12V/8300mAh 9V/11000mAh 5V/20000mAh" (eBay listing). It is a finished pack with its own charger, protection and DC/USB outputs, rated 72 W, not a bare 3S pack. The power board takes its 12 V DC output. The listing doesn't say whether that output is regulated or the 3S cells' raw voltage; this README assumes the worst case, 9.0 V empty to 12.6 V full. Measure it at full charge and near empty, and fuse the input on the power board anyway.
  • Put the power switch and the low-battery cutoff on the power board. The audio board can't turn the power off itself, and its firmware assumes the power can disappear at any time.
  • Battery level (J6.3, BAT): a voltage proportional to the battery, scaled to 0–3.3 V.
    • Keep its source impedance at 10 kΩ or less. The audio board loads BAT with 20 kΩ (its R13 + R22) and reads V × 10k / (20k + R_source), where V is the divider's open-circuit output. With a stiff source that is half of BAT.
    • Record the divider's ratio and source impedance in the audio board's DESIGN.md ("Power board connector (J6)"), so the firmware can convert the reading to volts. Rev 1 uses 30k over 10k: 0.25 from 7.5 kΩ.
    • Switch the divider off with the 5 V output, so it doesn't drain the battery while the amp is off.
    • For a 12.6 V maximum, 30 kΩ over 10 kΩ would do: a ratio of 0.25 (3.15 V at 12.6 V) from a 7.5 kΩ source.

Speaker amp

  • Input (J5): wire LINE+ to the amp's IN+ and LINE− to its IN− only, never to the amp's GND as well. LINE− is the audio board's ground through 1 kΩ, so the amp rejects any voltage between the two boards' grounds. Tied to the amp's GND, LINE− would close a ground loop through J6 and J5.
  • Input impedance: 10 kΩ or more per leg. The audio board drives each leg through 1 kΩ, so full scale arrives at ≈ 0.83 Vrms differential into 10 kΩ (−1.7 dB), and ≈ 3.0 dB lower into 5 kΩ. Choose the amp's gain for that level. J5 should sit at ≈ 0 V DC (the audio board's TEST_PLAN 5.16 confirms it).
  • Mute (J6.4, MUTE): the audio board pulls MUTE to GND through Q2 and a 470 Ω resistor to let the speaker play, and leaves it open to mute. So:
    • Pull MUTE up on the power board, with 4.7 kΩ or more to at most 5 V. The amp is then muted whenever the audio board is unpowered, booting, reset or unplugged.
    • Low (speaker on) is ≈ 0.24 V against a 10 kΩ pull-up and ≈ 0.5 V against 4.7 kΩ. The amp's mute or shutdown input has to read that as "play" and a pulled-up line as "mute". If the chosen amp's pin works the other way, invert it on the power board.
  • The speakers: 10" 4 Ω cones, interchangeable, one at a time:
    • Guitar-voiced: Jensen MOD10-50, 4 Ω version (Amplified Parts). 50 W rated, ≈ 95 dB at 1 W / 1 m, 3.08 Ω DC resistance (distributor figures; the product page couldn't be read). The amp's ≈ 17 W maximum is well inside its rating, and gives roughly 105–107 dB at 1 m.
    • "Flat" response: Skar Audio FSX10-4, a 10" 4 Ω pro-audio midrange (eBay listing). The listing gives 400 W and no sensitivity or response figures. Either way it is far above the amp's ≈ 17 W.
  • Speaker wiring: the speaker wiring is on the power board. The cone's spade tabs (6.3 mm / 4.8 mm) take crimped quick-disconnects. Most class D amps have a bridged output, so neither speaker wire may be grounded.
The amp: TI TPA3118D2

The power board uses the TPA3118D2 (TPA3116D2/TPA3118D2/TPA3130D2 datasheet, SLOS708G). It meets each point above as follows:

  • Mute: its MUTE pin is active high (high = outputs Hi-Z, low = outputs on) with TTL levels, so SPK_MUTE wires straight to it with the pull-up above and no inverter. MUTE's levels are compliant with AVCC, so pull it up to a rail no higher than AVCC. Use SDZ (active low) for the power board's own power-up and power-down sequencing.
  • Input: fully differential. LINE+ goes to the IN+ pin and LINE− to the IN− pin, each through its own coupling cap (the inputs sit at an internal bias). Use the same type and value on both legs so they stay matched; the datasheet suggests 1.5 µF at 20 dB.
  • Gain and input impedance: the gain is set by the GAIN/SLV divider, and the input impedance falls as the gain rises, from 60 kΩ at 20 dB to 9 kΩ at 36 dB, ±20 %. Use 32 dB or less: 36 dB breaks the 10 kΩ-per-leg minimum.
  • Use 20 dB, the lowest setting. The audio board's full scale (1 Vrms, ≈ 0.98 Vrms after its 1 kΩ legs into 60 kΩ) becomes ≈ 9.8 Vrms, which already clips on the battery: ≈ 1.5 dB below full scale on a full pack, ≈ 2.5 dB at 11.1 V and ≈ 4.5 dB near 9 V. The firmware should cap the speaker level about 5 dB below full scale (or use the PLIMIT pin). A higher gain would only clip sooner.
  • Supply: 4.5–26 V, straight from the power bank's 12 V output (9.0–12.6 V assumed). AVCC is then always above 5 V, so the MUTE pull-up can go to the 5 V rail.
  • Output: bridged, or both channels in PBTL for the single speaker (PBTL halves each output stage's current, so it runs cooler). Neither speaker wire may be grounded. Into 4 Ω, expect roughly 17 W at clipping on a full pack, 13 W at 11.1 V and 9 W near 9 V (estimated from the supply, allowing ≈ 0.3 Ω for the output switches and filter inductors). That draws up to ≈ 1.6 A from the battery on loud peaks, far less on average.
  • Package: HTSSOP-32 with its thermal pad underneath. Lay the pad out with vias that can be soldered from the back, or use hot air.

Display

  • Supply the display's 5 V directly from the power board, with its own wire pair, so its current pulses (ESP32-S3 Wi-Fi, backlight PWM) never flow through the audio board's +5V.

Wiring and placement

  • Use ferrules or solid wire in the screw terminals. Tinned stranded wire creeps under screw pressure and loosens.
  • Run J5 as a short twisted pair, away from the guitar input and the speaker wires.
  • Keep the power board's regulators and class D amp away from the audio board's analog circuits. The audio board's J6 is on its rear edge and J5 on its right edge, away from the front-edge jacks.
  • The audio board is designed to survive 5 V landing on BAT or MUTE, and probably on LINE+ (it puts ≈ 3 mA into the codec output's protection). Check every wire against the silkscreen label before powering up anyway.

Parts

127
QtyValueFootprintReferences
1310kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR3, R4, R6, R7, R8, R9, R13, R22, R101, R107, R109, R112, R113
6100kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR12, R17, R18, R19, R24, R111
5PESD5V0S1BADiode_SMD:D_SOD-323D1, D2, D3, D4, D5
410kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR25, R26, R27, R28
41uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC12, C13, C14, C15
4220n 25VCapacitor_SMD:C_0805_2012MetricC117, C118, C119, C120
4GNDTestPoint:TestPoint_Pad_D2.0mmTP102, TP105, TP107, TP108
3100n 10VCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC105, C107, C123
3100nFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC4, C6, C17
31kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR2, R11, R21
3470Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR5, R20, R23
3FiducialFiducial:Fiducial_1mm_Mask2mmFID1, FID2, FID3
3MountingHole_2.7mm_M2.5MountingHole:MountingHole_2.7mm_M2.5H1, H2, H3
21.5u 16V MATCHCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC108, C109
2100n 50VCapacitor_SMD:C_0805_2012MetricC113, C114
2100u 10VCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC104, C106
2100u 25VCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC111, C112
21nFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC3, C9
21u 10VCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC124, C125
22.2kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR108, R110
24.7uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC10, C11
2680n 50V X7RCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC121, C122
2BEAD BYPASS: shunt = directConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJP101, JP103
2MPZ1608S221ATA00Inductor_SMD:L_0603_1608MetricFB101, FB102
2OPTIONAL BULK ENABLEConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJP102, JP104
2SJ3-35063AGSeed3_Carrier:Jack_3.5mm_SameSky_SJ3-35063AG_HorizontalJ2, J4
2SRP1038A-100M 10uHHalliquest_Power:L_Bourns_SRP1038A_LeadFrameL101, L102
1+5V_RAWTestPoint:TestPoint_Pad_D2.0mmTP106
10R AMP ISOLATIONResistor_SMD:R_2512_6332MetricR105
1100n 25VCapacitor_SMD:C_0805_2012MetricC116
1100pFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1
110RResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR106
110k 1%Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR103
110u 10VCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC103
11MResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1
11u 16VCapacitor_SMD:C_0805_2012MetricC110
11u 25VCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC115
11uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC2
12N7002Package_TO_SOT_SMD:SOT-23Q2
13.3kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR10
13.3nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC16
130k 1%Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR102
14 ohm SPEAKER BTLTerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_HorizontalJ102
147uF 16VCapacitor_THT:CP_Radial_D5.0mm_P2.00mmC5
147uF 16VCapacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolderC7
15.6k 1%Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR104
1AMP_FAULTZTestPoint:TestPoint_Pad_D2.0mmTP109
1AMP_PVCCTestPoint:TestPoint_Pad_D2.0mmTP103
1AMP_SDZTestPoint:TestPoint_Pad_D2.0mmTP104
1AO3401APackage_TO_SOT_SMD:SOT-23Q1
1BZT52C12Diode_SMD:D_SOD-123D101
1DISPLAY USB POWER CABLETerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_HorizontalJ105
1DISPLAY_UARTTerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-3-3.5-H_1x03_P3.50mm_HorizontalJ3
1Daisy Seed3Module:Electrosmith_Daisy_SeedA1
1FROM DFR 5V / GNDTerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_HorizontalJ107
1IRF4905Package_TO_SOT_THT:TO-220-3_VerticalQ101
1MAX9722AEUE+Package_SO:TSSOP-16_4.4x5mm_P0.65mmU2
1NRJ4HFConnector_Audio:Jack_6.35mm_Neutrik_NRJ4HF_HorizontalJ1
1PANEL SPST - TERMINAL INTERFACETerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_HorizontalSW101
1PJ-102AHConnector_BarrelJack:BarrelJack_CUI_PJ-102AH_HorizontalJ101
1RESET / MANUAL FAULT CLEARConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJP105
1T3.15AHalliquest_Power:Fuseholder_Bulgin_FX0457_P10.00mmF101
1TLV9061IDBVRPackage_TO_SOT_SMD:SOT-23-5U1
1TO DFR VIN / GNDTerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_HorizontalJ106
1TPA3118D2DAPRHalliquest_Power:TI_DAP0032C_HTSSOP32_P0.65mm_EP3.04x3.74mmU101
1TPS3808EG50DBVRPackage_TO_SOT_SMD:SOT-23-6U103
1TP_HP_DETTestPoint:TestPoint_Pad_D2.0mmTP1
1VBAT_PROTECTEDTestPoint:TestPoint_Pad_D2.0mmTP101

More from B1narySolutions/amp-hardware

2
  • 2 layers98 × 98 mmRev1 Power Board, the printed circuit board in 3D

    Rev1 Power Board

    B1narySolutions/amp-hardware

    Monorepo for our capstone team's PCBs and housing

    67 parts
  • 2 layers90 × 56.5 mmSeed3-carrier, the printed circuit board in 3D

    Seed3-carrier

    B1narySolutions/amp-hardware

    Monorepo for our capstone team's PCBs and housing

    64 parts

Similar boards

  • 2 layers100 × 70 mmClassA, the printed circuit board in 3D

    ClassA

    smileym4n-collab/Kicadprojects

    67 parts
  • 2 layers101.3 × 101.3 mmForward Converter, the printed circuit board in 3D

    Forward Converter

    ozgurgulsuna/ELE713-SwitchedPowerSupplies

    Project

    110 parts1
  • 2 layers50 × 50 mm50x50 2 Layer, the printed circuit board in 3D

    50x50 2 Layer

    UC-Aerospace/Electrical-Tut-24

    Demo boards for the electrical tutorials

    76 parts1
  • 2 layers100 × 60 mmKINK box, the printed circuit board in 3D

    KINK box

    FunDeckHermit/KINK-box

    Audio amplifier / Web radio based on ESP32-S3

    112 parts2Apache-2.0
  • 4 layers130 × 105 mmHomeDeck, the printed circuit board in 3D

    HomeDeck

    Kilan777/HomeDeck

    Jarvis HomeDeck: a Raspberry Pi CM4 carrier board and voice-assistant software for a 7-inch smart display (KiCad hardware, generated from Python, plus the Python/JS assistant)

    228 parts1
  • 2 layers90 × 80 mmTestingPCB, the printed circuit board in 3D

    TestingPCB

    leslier7/thesis

    My Undergraduate Honors Thesis Code

    19 parts1
  • 4 layers100 × 100 mmBefore router, the printed circuit board in 3D

    Before router

    ahdrage/leafy

    DIY Wi-Fi climate-control prototype for Nissan Leaf: KiCad PCB, ESP32-C3 firmware, Blender enclosure and build notes. Inspired by OVMS.

    66 parts

Questions

How big is the Seed3-carrier PCB?

It measures 90 × 56.5 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Seed3-carrier use?

127 parts, built around the TLV9061QDBVRQ1, MAX9722AEUE+, TPA3118D2DAPR and PESD5V0S1BAF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Seed3-carrier KiCad files?

From the B1narySolutions/amp-hardware repository on GitHub, at the commit this page was made from: the board is audio-board/rev3/seed3-carrier.kicad_pcb and its schematic audio-board/rev2/seed3-carrier.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Seed3-carrier design in my own project?

Its repository states no licence, so its author keeps all rights: ask B1narySolutions before reusing the design.