
TCAN3413D
Texas InstrumentsExtended
- Part id
- ti/TCAN3413D
- Category
- CAN Transceivers
- Package
- SOIC-8
- Pins
- 8
- In stock
- 9,602 at JLCPCB (C22433320)
- Used on
- 6 open-source boards
Overview
The TCAN3413D is a CAN Transceiver made by Texas Instruments in a SOIC-8 package with 8 pins.
PCBKit's library has its KiCad symbol (TCAN3413DR:TCAN3413DR, from Antmicro) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 9,602 are in stock at JLCPCB (part C22433320). 6 open-source boards in 5 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
15- Supply, least
- 3 V · VCC, recommended operating min · p. 4
- Supply, most
- 3.6 V · VCC, recommended operating max · p. 4
- Supply, least
- 1.7 V · VIO, recommended operating min · p. 4
- Supply, absolute maximum
- 6 V · VCC, absolute max · p. 4
- Junction, hottest
- 165 °C · Junction temperature absolute max · p. 4
- Takes working
- 42.13 mA · sum of VCC and VIO typical normal dominant currents, RL = 60 Ω · p. 5
- Takes at most
- 60.3 mA · sum of VCC and VIO max normal dominant currents; VCC at RL = 50 Ω, VIO at RL = 60 Ω · p. 5
- Takes asleep
- 10 µA · sum of VCC and VIO typical standby currents · p. 5
- A pin gives at most
- 8 mA · RXD output source or sink absolute max · p. 4
- Junction to air (D (SOIC))
- 114.4 K/W · Junction-to-ambient thermal resistance · p. 4
- Junction to case (D (SOIC))
- 49 K/W · Junction-to-case top thermal resistance · p. 4
- Junction to board (D (SOIC))
- 58 K/W · Junction-to-board thermal resistance · p. 4
- Edge
- 10 ns · RXD output rise time, typical, CL(RXD) = 15 pF · p. 10
- Works from
- -40 °C · minimum operating temperature, SOIC (D) · p. 31
- Works up to
- 125 °C · maximum operating temperature, SOIC (D) · p. 31
What it is and has
9- Supply
- 3.3 V single supply operation · p. 1
- CAN FD
- Optimized performance at 2, 5, and 8 Mbps · p. 1
- Receiver common mode input voltage
- ±30 V · p. 1
- Protection
- Bus fault protection: ±58 V · p. 1
- Protection
- IEC ESD protection on bus pins: ±10 kV · p. 1
- Protection
- Undervoltage protection · p. 1
- Protection
- TXD-dominant time-out (DTO) · p. 1
- Protection
- Thermal-shutdown protection (TSD) · p. 1
- Logic interface
- VIO for 1.8 V, 2.5 V or 3.3 V microcontrollers · p. 16
Around it
1- res 120 Ω
- between CANH and CANL; One termination resistor at each end of the bus, on the cable or in a terminating node. · p. 24
Specifications
125| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage VCC | min -0.3 · max 6 V | 4 | |
| Supply voltage I/O level shifter (only for TCAN3413) VIO | TCAN3413 | min -0.3 · max 6 V | 4 |
| CAN bus I/O voltage range on CANH and CANL VBUS | min -58 · max 58 V | 4 | |
| Max differential voltage between CANH and CANL VDIFF | VDIFF = (CANH - CANL) | min -58 · max 58 V | 4 |
| Logic pin input voltage (TXD, STB, SHDN) VLogic_Input | min -0.3 · max 6 V | 4 | |
| Logic output voltage range (RXD) VRXD | min -0.3 · max 6 V | 4 | |
| RXD output current IO(RXD) | min -8 · max 8 mA | 4 | |
| Junction temperature TJ | min -40 · max 165 °C | 4 | |
| Storage temperature TSTG | min -65 · max 150 °C | 4 | |
| Electrostatic discharge VESD | Human-body model (HBM), classification level 3A for all pins; ±4000 V | max 4000 V | 4 |
| Electrostatic discharge VESD | Human-body model (HBM), classification level 3B for global pins CANH and CANL with respect to GND; ±10000 V | max 10000 V | 4 |
| Electrostatic discharge VESD | Charged-device model (CDM), classification level C5 for all pins; ±750 V | max 750 V | 4 |
| System level electrostatic discharge VESD | CAN bus terminals (CANH, CANL) to GND, IEC61000-4-2; ±10000 V | max 10000 V | 4 |
| Supply voltage VCC | 3.3 V nominal | min 3 · typ 3.3 · max 3.6 V | 4 |
| Supply voltage for I/O level shifter (only for TCAN3413) VIO | TCAN3413 | min 1.7 · max 3.6 V | 4 |
| RXD terminal high-level output current IOH(RXD) | min -2 mA | 4 | |
| RXD terminal low-level output current IOL(RXD) | max 2 mA | 4 | |
| RXD terminal high-level output current (only for TCAN3413) IOH(RXD) | TCAN3413 | min -1.5 mA | 4 |
| RXD terminal low-level output current (only for TCAN3413) IOL(RXD) | TCAN3413 | max 1.5 mA | 4 |
| Junction temperature TJ | min -40 · max 150 °C | 4 | |
| Junction-to-ambient thermal resistance RΘJA | TCAN3413, D (SOIC) | typ 114.4 ℃/W | 4 |
| Junction-to-case (top) thermal resistance RΘJC(top) | TCAN3413, D (SOIC) | typ 49 ℃/W | 4 |
| Junction-to-board thermal resistance RΘJB | TCAN3413, D (SOIC) | typ 58 ℃/W | 4 |
| Junction-to-top characterization parameter ΨJT | TCAN3413, D (SOIC) | typ 7 ℃/W | 5 |
| Junction-to-board characterization parameter ΨJB | TCAN3413, D (SOIC) | typ 57.1 ℃/W | 5 |
| Supply current normal mode ICC | Dominant; TXD = 0 V, STB = 0 V, RL = 60 Ω, CL = open | typ 42 · max 55 mA | 5 |
| Supply current normal mode ICC | Dominant; TXD = 0 V, STB = 0 V, RL = 50 Ω, CL = open | typ 50 · max 60 mA | 5 |
| Supply current normal mode ICC | Recessive; TXD = VCC, STB = 0 V, RL = 50 Ω, CL = open | typ 7 · max 8.2 mA | 5 |
| Supply current normal mode ICC | Dominant with bus fault; TXD = 0 V, STB = 0 V, CANH = CANL = ±25 V, RL = open, CL = open | max 130 mA | 5 |
| Supply current standby mode (TCAN3413) ICC | TXD = STB = VIO, RL = 50 Ω, CL = open, TJ <= 85 °C | typ 1 · max 2 uA | 5 |
| Supply current standby mode (TCAN3413) ICC | TXD = STB = VIO, RL = 50 Ω, CL = open, TJ <= 125 °C | typ 1 · max 3 uA | 5 |
| Supply current standby mode (TCAN3413) ICC | TXD = STB = VIO, RL = 50 Ω, CL = open, TJ <= 150 °C | typ 1 · max 4 uA | 5 |
| I/O supply current normal mode IIO | TCAN3413; Dominant; TXD = 0 V, STB = 0 V, RL = 60 Ω, CL = open, RXD floating | typ 125 · max 300 uA | 5 |
| I/O supply current normal mode IIO | TCAN3413; recessive; TXD = VIO, STB = 0 V, RL = 60 Ω, CL = open, RXD floating | typ 19 · max 48 uA | 5 |
| I/O supply current standby mode IIO | TCAN3413; TXD = VIO, STB = VIO, RL = 60 Ω, CL = open, RXD floating, TJ <= 85 °C | typ 9 · max 13 uA | 5 |
| I/O supply current standby mode IIO | TCAN3413; TXD = VIO, STB = VIO, RL = 60 Ω, CL = open, RXD floating, TJ <= 125 °C | typ 9 · max 14 uA | 5 |
| I/O supply current standby mode IIO | TCAN3413; TXD = VIO, STB = VIO, RL = 60 Ω, CL = open, RXD floating, TJ <= 150 °C | typ 9 · max 15 uA | 5 |
| Undervoltage detection VCC rising UVCC(R) | Ramp up | typ 2.75 · max 2.9 V | 5 |
| Undervoltage detection on VCC falling UVCC(F) | Ramp down | min 2.5 · typ 2.65 V | 5 |
| Hysteresis voltage on UVCC VHYS(UVCC) | typ 120 mV | 6 | |
| Undervoltage detection VIO rising (TCAN3413) UVIO(R) | Ramp up | typ 1.6 · max 1.65 V | 6 |
| Undervoltage detection on VIO falling (TCAN3413) UVIO(F) | Ramp down | min 1.4 · typ 1.5 V | 6 |
| Hysteresis voltage on UVIO VHYS(UVIO) | typ 50 mV | 6 | |
| Average power dissipation Normal mode PD | VCC = 3.3 V, TJ = 27°C, RL = 60Ω, CL_RXD = 15 pF; TXD input = 250 kHz 50% duty cycle square wave | typ 50 mW | 6 |
| Average power dissipation Normal mode PD | VCC = 3.6 V, TJ = 150°C, RL = 50Ω, CL_RXD = 15 pF; TXD input = 2.5 MHz 50% duty cycle square wave | typ 60 mW | 6 |
| Thermal shutdown temperature TTSD | typ 192 °C | 6 | |
| Thermal shutdown hysteresis TTSD_HYS | typ 10 °C | 6 | |
| Dominant output voltage normal mode VO(DOM) | CANH; TXD = 0 V, STB, SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = open; maximum VCC | min 2.25 V | 6 |
| Dominant output voltage normal mode VO(DOM) | CANL; TXD = 0 V, STB, SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = open | min 0.5 · max 1.25 V | 6 |
| Recessive output voltage normal mode VO(REC) | CANH and CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = open (no load), CL = open | min 1.5 · typ 1.9 · max 2.25 V | 6 |
| Driver symmetry {(VO(CANH) + VO(CANL))/(VO(REC_CANH) + VO(REC_CANL)} VSYM | TXD = 250 kHz, 1 MHz, 2.5 MHz, STB, SHDN = 0 V; RL = 60, CSPLIT = 4.7 nF, CL = open | min 0.9 · max 1.1 V/V | 6 |
| DC output symmetry (CANHREC + CANLREC - CANHDOM - CANLDOM) VSYM_DC | STB, SHDN = 0 V; RL = 60 Ω, CL = open | min -400 · max 400 mV | 6 |
| Differential output voltage normal mode Dominant VOD(DOM) | CANH - CANL; TXD = 0 V, STB. SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = open | min 1.5 · max 3 V | 6 |
| Differential output voltage normal mode Dominant VOD(DOM) | CANH - CANL; TXD = 0 V, STB, SHDN = 0 V; 45 Ω ≤ RL ≤ 70 Ω, CL = open | min 1.4 · max 3 V | 6 |
| Differential output voltage normal mode Dominant VOD(DOM) | CANH - CANL; TXD = 0 V, STB, SHDN = 0 V; RL = 2240 Ω, CL = open | min 1.5 · max 3.4 V | 6 |
| Differential output voltage normal mode Recessive VOD(REC) | CANH - CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = 60 Ω, CL = open | min -120 · max 12 mV | 6 |
| Differential output voltage normal mode Recessive VOD(REC) | CANH - CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = open, CL = open | min -50 · max 50 mV | 6 |
| Bus output voltage standby mode VO(STB) | CANH; TXD = STB = VIO or VCC; RL = open, CL = open | min -0.1 · max 0.1 V | 7 |
| Bus output voltage standby mode VO(STB) | CANL; TXD = STB = VIO or VCC; RL = open, CL = open | min -0.1 · max 0.1 V | 7 |
| Bus output voltage standby mode VO(STB) | CANH - CANL; TXD = STB = VIO or VCC; RL = open, CL = open | min -0.2 · max 0.2 V | 7 |
| Short-circuit bus output current, dominant, normal mode IOS(DOM) | V(CANH) = -15 V to 40 V, CANL = open, TXD = 0 V | min -115 · max 115 mA | 7 |
| Short-circuit bus output current, dominant, normal mode IOS(DOM) | V(CAN_L) = -15 V to 40 V, CANH = open, TXD = 0 V | min -115 · max 115 mA | 7 |
| Short-circuit steady-state output current, recessive, normal mode IOS(REC) | V(CANH) = -27 V to 32 V, CANL = open, STB=0, TXD = VIO or VCC | min -7 · max 7 mA | 7 |
| Short-circuit steady-state output current, recessive, normal mode IOS(REC) | V(CANL) = -27 V to 32 V, CANH = open, STB = 0, TXD = VIO or VCC | min -7 · max 7 mA | 7 |
| Input threshold voltage normal mode VIT | -30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 V | min 500 · max 900 mV | 7 |
| Input threshold standby mode, TCAN3413 VIT(STB) | VIO = 3 V to 3.6 V, -30 V ≤ VCM ≤ 30 V, STB= VIO | min 400 · max 1150 mV | 7 |
| Input threshold standby mode, TCAN3413 VIT(STB) | VIO = 1.7 V to 1.9 V, 2.25 V to 2.75 V, -12 V ≤ VCM ≤ 12 V, STB= VIO | min 400 · max 1150 mV | 7 |
| Normal mode dominant state differential input voltage range VDOM | -30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 V | min 0.9 · max 9 V | 7 |
| Normal mode recessive state differential input voltage range VREC | -30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 V | min -4 · max 0.5 V | 7 |
| Standby mode dominant state differential input voltage range VDOM(STB) | SHDN= 0 V, STB = VIO, -30 V ≤ VCM ≤ 30 V | min 1.15 · max 9 V | 7 |
| Standby mode recessive state differential input voltage range VREC(STB) | SHDN = 0 V, STB = VIO, -30 V ≤ VCM ≤ 30 V | min -4 · max 0.4 V | 7 |
| Hysteresis voltage for input threshold normal mode VHYS | -30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 V | typ 50 mV | 7 |
| Common mode range normal and standby modes VCM | See Figure 6-3 and Table 7-6 | min -30 · max 30 V | 7 |
| Unpowered bus input leakage current ILKG(IOFF) | CANH = CANL = 5 V, VCC = VIO = GND | max 5 uA | 7 |
| Input capacitance to ground (CANH or CANL) CI | TXD = VIO | max 40 pF | 7 |
| Differential input capacitance CID | TXD = VIO | max 20 pF | 7 |
| Differential input resistance RID | TXD = VIO, STB = 0 V -30 V ≤ VCM ≤ 30 V | min 25 · max 50 kΩ | 7 |
| Single ended input resistance (CANH or CANL) RIN | TXD = VIO, STB = 0 V -30 V ≤ VCM ≤ 30 V | min 13 · max 25 kΩ | 7 |
| Input resistance matching [1 – (RIN(CANH) / RIN(CANL))] × 100 % RIN(M) | V(CAN_H) = V(CAN_L) = 5 V | min -3 · max 3 % | 7 |
| High-level input leakage current IIH | TXD = VCC = VIO = 3.6 V | min -2.5 · typ 0 · max 1 uA | 7 |
| Low-level input leakage current IIL | TXD = 0 V, VCC = VIO = 3.6 V | min -200 · typ -100 · max -20 uA | 7 |
| Unpowered leakage current ILKG(OFF) | TXD = 3.6 V, VCC = VIO = 0 V | min -1 · typ 0 · max 1 uA | 7 |
| Input capacitance CI | typ 4 pF | 8 | |
| Unpowered leakage current ILKG(OFF) | RXD = 3.6 V, VCC = VIO = 0 V | min -1 · typ 0 · max 1 uA | 8 |
| High-level input leakage current IIH | STB; VCC = VIO = STB = 3.6 V | min -2 · max 2 uA | 8 |
| Low-level input leakage current IIL | STB; VCC = VIO = 3.6 V, STB = 0 V | min -20 · max -2 uA | 8 |
| Unpowered leakage current ILKG(OFF) | STB = 3.6V, VCC= VIO = 0 V | min -1 · typ 0 · max 1 uA | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), recessive to dominant tPROP(LOOP1) | TCAN3413; See Figure 6-4, normal mode, VCC = VIO = 3 V to 3.6 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | typ 95 · max 180 ns | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), recessive to dominant tPROP(LOOP1) | TCAN3413; See Figure 6-4, normal mode, VCC = 3 to 3.6 V, VIO = 2.25 V to 2.75 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | typ 102 · max 190 ns | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), recessive to dominant tPROP(LOOP1) | TCAN3413; See Figure 6-4, normal mode, VCC = 3 to 3.6 V, VIO = 1.71 V to 1.89 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | typ 115 · max 210 ns | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), dominant to recessive tPROP(LOOP2) | TCAN3413; See Figure 6-4, normal mode, VCC = VIO = 3 V to 3.6 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | typ 120 · max 180 ns | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), dominant to recessive tPROP(LOOP2) | TCAN3413; See Figure 6-4, normal mode, VCC = 3 to 3.6 V, VIO = 2.25 V to 2.75 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | typ 125 · max 190 ns | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), dominant to recessive tPROP(LOOP2) | TCAN3413; See Figure 6-4, normal mode, VCC = 3 to 3.6 V, VIO = 1.71 V to 1.89 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | typ 140 · max 210 ns | 8 |
| Mode change time, from normal to standby or from standby to normal tMODE | See Figure 6-5 | max 30 us | 9 |
| Filter time for a valid wake-up pattern tWK_FILTER | See Figure 7-5 | min 0.5 · max 1.8 us | 9 |
| Bus wake-up timeout value tWK_TIMEOUT | See Figure 7-5 | min 0.8 · max 6 ms | 9 |
| Time duration after VCC or VIO hass cleared UV+, and device can resume normal operation Tstartup | max 1.5 ms | 9 | |
| Filter on STB pin to filter out any glitches Tfilter(STB) | min 0.5 · typ 1 · max 2 us | 9 | |
| Propagation delay time, low-to-high TXD edge to driver recessive (dominant to recessive) tprop(TxD-busrec) | TCAN3413; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = VIO = 3 V to 3.6 V | typ 65 · max 100 ns | 9 |
| Propagation delay time, low-to-high TXD edge to driver recessive (dominant to recessive) tprop(TxD-busrec) | TCAN3413; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = 3 to 3.6 V, VIO = 2.25 V to 2.75 V | typ 67 · max 110 ns | 9 |
| Propagation delay time, low-to-high TXD edge to driver recessive (dominant to recessive) tprop(TxD-busrec) | TCAN3413; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = 3 to 3.6 V, VIO = 1.71 V to 1.89 V | typ 71 · max 110 ns | 9 |
| Propagation delay time, high-to-low TXD edge to driver dominant (recessive to dominant) tprop(TxD-busdom) | TCAN3413; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = VIO = 3 V to 3.6 V | typ 46 · max 100 ns | 9 |
| Propagation delay time, high-to-low TXD edge to driver dominant (recessive to dominant) tprop(TxD-busdom) | TCAN3413; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = 3 to 3.6 V, VIO = 2.25 V to 2.75 V | typ 48 · max 110 ns | 9 |
| Propagation delay time, high-to-low TXD edge to driver dominant (recessive to dominant) tprop(TxD-busdom) | TCAN3413; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = 3 to 3.6 V, VIO = 1.71 V to 1.89 V | typ 53 · max 110 ns | 9 |
| Pulse skew (|tprop(TxD-busrec) - tprop(TxD-busdom)|) tsk(p) | STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, See Figure 6-2 | typ 18 · max 28 ns | 9 |
| Differential output signal rise time tR | See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF | typ 32 · max 57 ns | 9 |
| Differential output signal fall time tF | See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF | typ 30 · max 50 ns | 9 |
| Dominant timeout tTXD_DTO | See Figure 6-6, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF | min 1.2 · max 4 ms | 9 |
| Propagation delay time, bus recessive input to RXD high output (dominant to recessive) tprop(busrec-RXD) | TCAN3413; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = VIO = 3 V to 3.6 V | typ 55 · max 90 ns | 9 |
| Propagation delay time, bus recessive input to RXD high output (dominant to recessive) tprop(busrec-RXD) | TCAN3413; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = 3 to 3.6 V, VIO = 2.25 V to 2.75 V | typ 60 · max 90 ns | 9 |
| Propagation delay time, bus recessive input to RXD high output (dominant to recessive) tprop(busrec-RXD) | TCAN3413; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = 3 to 3.6 V, VIO = 1.71 V to 1.89 V | typ 70 · max 102 ns | 9 |
| Propagation delay time, bus dominant input to RXD low output (recessive to dominant) tprop(busdom-RXD) | TCAN3413; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = VIO = 3 V to 3.6 V | typ 45 · max 90 ns | 10 |
| Propagation delay time, bus dominant input to RXD low output (recessive to dominant) tprop(busdom-RXD) | TCAN3413; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = 3 to 3.6 V, VIO = 2.25 V to 2.75 V | typ 51 · max 90 ns | 10 |
| Propagation delay time, bus dominant input to RXD low output (recessive to dominant) tprop(busdom-RXD) | TCAN3413; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = 3 to 3.6 V, VIO = 1.71 V to 1.89 V | typ 60 · max 100 ns | 10 |
| RXD output signal rise time tR | See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF | typ 10 · max 25 ns | 10 |
| RXD output signal fall time tF | See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF | typ 10 · max 28 ns | 10 |
| Bit time on CAN bus output pins with tBIT(TXD) = 500 ns tBIT(BUS) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | min 450 · max 525 ns | 10 |
| Bit time on CAN bus output pins with tBIT(TXD) = 200 ns tBIT(BUS) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | min 160 · max 205 ns | 10 |
| Bit time on CAN bus output pins with tBIT(TXD) = 125 ns(1) tBIT(BUS) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; Min/Max limits based on characterization | min 85 · max 130 ns | 10 |
| Bit time on RXD output pins with tBIT(TXD) = 500 ns tBIT(RXD) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | min 410 · max 540 ns | 10 |
| Bit time on RXD output pins with tBIT(TXD) = 200 ns tBIT(RXD) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | min 130 · max 210 ns | 10 |
| Bit time on RXD output pins with tBIT(TXD) = 125 ns(1) tBIT(RXD) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; Min/Max limits based on characterization | min 75 · max 135 ns | 10 |
| Receiver timing symmetry with tBIT(TXD) = 500 ns ΔtREC | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS) | min -50 · max 20 ns | 10 |
| Receiver timing symmetry with tBIT(TXD) = 200 ns ΔtREC | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS) | min -40 · max 10 ns | 10 |
| Receiver timing symmetry with tBIT(TXD) = 125 ns(1) ΔtREC | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS); Min/Max limits based on characterization | min -40 · max 10 ns | 10 |
Pins, by the datasheet
8- 1 TXD
- CAN transmit data input; integrated pull-up. · p. 3
- 2 GND
- Ground connection. · p. 3
- 3 VCC
- 3.3 V supply voltage. · p. 3
- 4 RXD
- CAN receive data output, tri-stated when device powered off. · p. 3
- 5 VIO
- I/O supply voltage (TCAN3413 only). · p. 3
- 6 CANL
- Low-level CAN bus input/output line. · p. 3
- 7 CANH
- High-level CAN bus input/output line. · p. 3
- 8 STB
- Standby input for mode control; integrated pull-up. · p. 3
Ordering codes, by the datasheet
2- TCAN3413DR
- SOIC (D) | 8 · 2500 units, LARGE T&R; operating temperature -40 to 125 °C · p. 31
- TCAN3413DR.A
- SOIC (D) | 8 · 2500 units, LARGE T&R; operating temperature -40 to 125 °C · p. 31
Open-source boards using it
6- 2 layers50 × 50 mm

- 2 layers151.4 × 128.5 mm

- 4 layers65 × 55 mm

Gateway
opensimgear/device-gateway
Work-in-progress STM32 Cyphal/CAN-to-USB gateway with automatic input/output enrollment, ordered HID controllers, guarded configuration/leased action/event routing and native/Pico debug simulation.
45 parts - 2 layers65 × 56 mm

Industrial hat rpi4
V2gkr/industrial_hat_rpi4
hat to communicate via rs232, rs485, can fd with galvanic isolation
52 parts - 4 layers53 × 75.9 mm

- 4 layers85 × 75 mm

Starter
opensimgear/device-template
Work-in-progress STM32G0B1 input/output module with USB HID or CDC-only profiles, Cyphal/CAN, persistent settings, ordered panel events, leased LED/display actions, KiCad hardware and native simulation.
111 parts
Parts like it
8TJA1051T/3/1J
SOIC-8-150mil-40℃~+150℃ 110mA 4.5V~5.5V 5Mbps CAN FD Transceiver SOIC-8-150mil CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversSN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTJA1042T/1J
SOIC-8-40℃~+150℃ 15uA 4.5V~5.5V 5Mbps 70mA CAN FD Transceiver SOIC-8 CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversCA-IF1051S
SOIC-8-55℃~+150℃ 2Mbps 4.5V~5.5V 80mA CAN Transceiver SOIC-8 CAN Transceivers ROHSChipanalogCAN TransceiversTJA1042T/3/1J
SOIC-8-40℃~+150℃ 15uA 4.5V~5.5V 5Mbps 70mA SOIC-8 CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversTJA1044T/1Z
SOIC-8-40℃~+150℃ 15uA 1Mbit/s 4.5V~5.5V 60mA CAN Transceiver SOIC-8 CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversSIT1050T
SO-8-40℃~+125℃ 1 10mA 1Mbps 4.5V~5.5V 70mA CAN Transceiver TXD dominant timeout、Thermal shutdown protection、Short-Circuit Protection、Silent mode SO-8 CAN Transceivers ROHSSITCAN TransceiversSN65HVD232D
SOIC-8-40℃~+85℃ 17mA 1Mbps 3.3V CAN Transceiver SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
Questions
Is there a KiCad symbol and footprint for the TCAN3413D?
Yes. The symbol is TCAN3413DR:TCAN3413DR and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TCAN3413D?
SOIC-8, with 8 pins. Its footprint is drawn on this page.
Where is the TCAN3413D datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TCAN3413D?
JLCPCB lists it as part C22433320, with 9,602 in stock; the sellers' links on this page open their listings.
What can replace the TCAN3413D?
Parts like it in the library: the TJA1051T/3/1J by NXP Semiconductors, the SN65HVD230D by Texas Instruments, the TJA1042T/1J by NXP Semiconductors and the CA-IF1051S by Chipanalog. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TCAN3413D?
6 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.