Skip to the content
12345678910111213141516

TCA9534PW

Texas InstrumentsExtended

-40℃~+85℃ 1.5uA 1.65V~5.5V 10mA 25mA 4.1V 400kHz 500mV 8 8 I2C Interrupt Output Push-Pull Reset function、Cascade and address expansion、Built-in LED driver TSSOP-16 I/O Expanders ROHS

Part id
ti/TCA9534PW
Category
I, O Expanders
Package
TSSOP-16
Pins
16
In stock
9,058 at JLCPCB (C783615)
Used on
32 open-source boards

Overview

The TCA9534PW is an i, O Expander made by Texas Instruments in a TSSOP-16 package with 16 pins. -40℃~+85℃ 1.5uA 1.65V~5.5V 10mA 25mA 4.1V 400kHz 500mV 8 8 I2C Interrupt Output Push-Pull Reset function、Cascade and address expansion、Built-in LED driver TSSOP-16 I/O Expanders ROHS.

PCBKit's library has its KiCad symbol (Interface_Expansion:TCA9534, from KiCad's library) and its footprint (Package_SO:TSSOP-16_4.4x5mm_P0.65mm, from KiCad's library), ready for a KiCad board. 9,058 are in stock at JLCPCB (part C783615). 32 open-source boards in 26 repositories on GitHub use it.

Symbol

1A02A13A24P05P16P27P38GND9P410P511P612P713INT14SCL15SDA16VDD
Interface_Expansion:TCA9534From KiCad's library

Footprint

12345678910111213141516
Package_SO:TSSOP-16_4.4x5mm_P0.65mmFrom KiCad's library

From the datasheet

13
Supply, least
1.65 V · VCC, recommended operating min · p. 5
Supply, most
5.5 V · VCC, recommended operating max · p. 5
Supply, absolute maximum
6 V · VCC, absolute maximum · p. 5
Works from
-40 °C · Operating free-air temperature min · p. 5
Works up to
85 °C · Operating free-air temperature max · p. 5
Junction, hottest
100 °C · Junction temperature max · p. 5
Takes working
11 µA · VCC operating typical, 3.6 V, inputs, 400 kHz, no load · p. 7
Takes at most
40 µA · VCC operating max, 5.5 V, inputs, 400 kHz, no load · p. 7
Takes asleep
900 nA · VCC standby typical, 3.6 V, VI = VCC, no load · p. 7
A pin gives at most
50 mA · Single P-port continuous output low current absolute max · p. 5
Junction to air (PW (TSSOP))
122 K/W · Junction-to-ambient thermal resistance · p. 6
Junction to case (PW (TSSOP))
56.4 K/W · Junction-to-case top thermal resistance · p. 6
Junction to board (PW (TSSOP))
67.1 K/W · Junction-to-board thermal resistance · p. 6

What it is and has

8
Interface
I2C to parallel port expander · p. 1
Interrupt
Active-low open-drain output · p. 1
I2C clock
400 kHz fast mode · p. 1
I/O voltage tolerance
5 V · p. 1
Configuration
Input and output configuration registers · p. 1
Polarity inversion
Polarity inversion register · p. 1
Reset
Internal power-on reset · p. 1
Input filtering
Noise filters on SCL/SDA inputs · p. 1

Around it

3
res unspecified
between INT and VCC; Pullup resistor. · p. 4
res unspecified
between SCL and VCC; Pullup resistor. · p. 4
res unspecified
between SDA and VCC; Pullup resistor. · p. 4

Specifications

104
ParameterConditionsAs printedPage
Supply voltage VCCOver operating free-air temperature rangemin -0.5 · max 6 V5
Input voltage VISubject to footnote (2)min -0.5 · max 6 V5
Output voltage VOSubject to footnote (2)min -0.5 · max 6 V5
Input clamp current IIKVI < 0max -20 mA5
Output clamp current IOKVO < 0max -20 mA5
Input-output clamp current IIOKVO < 0 or VO > VCC; limit ±20 mAmax 20 mA5
Continuous output low current through a single P-port IOLVO = 0 to VCCmax 50 mA5
Continuous output high current through a single P-port IOHVO = 0 to VCCmax -50 mA5
Continuous current through GND by all P-ports, INT, and SDA ICCmax 250 mA5
Continuous current through VCC by all P-ports ICCmax -160 mA5
Maximum junction temperature TJ(MAX)max 100 °C5
Storage temperature Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V5
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101; ±1000 Vmax 1000 V5
Supply voltage VCCmin 1.65 · max 5.5 V5
High-level input voltage VIHA0, A1, A2, P7–P0; VCC = 1.65 V to 5.5 V; min 0.7 × VCCmax 5.5 V5
Low-level input voltage VILSCL, SDA; VCC = 1.65 V to 5.5 V; max 0.3 × VCCmin -0.5 V5
Low-level input voltage VILA0, A1, A2, P7–P0; VCC = 1.65 V to 5.5 V; max 0.3 × VCCmin -0.5 V5
Low-level input voltage VILA0, A1, A2, P7–P0; VCC = 3 V to 5.5 V; max 0.2 × VCCmin -0.5 V5
High-level output current IOHAny P-port, P7–P0max -10 mA5
Low-level output current IOLP00–P07, P10–P17; Tj ≤ 65°Cmax 25 mA5
Low-level output current IOLP00–P07, P10–P17; Tj ≤ 85°Cmax 18 mA5
Low-level output current IOLP00–P07, P10–P17; Tj ≤ 105°Cmax 9 mA5
Low-level output current IOLINT, SDA; Tj ≤ 85°Cmax 6 mA5
Low-level output current IOLINT, SDA; Tj ≤ 105°Cmax 3 mA5
Continuous current through GND ICCAll P-ports P7-P0, INT, and SDAmax 200 mA5
Continuous current through VCC ICCAll P-ports P7-P0max -80 mA5
Operating free-air temperature TAmin -40 · max 85 °C5
Junction-to-ambient thermal resistance RθJAPW (TSSOP), 16 pinstyp 122 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)PW (TSSOP), 16 pinstyp 56.4 °C/W6
Junction-to-board thermal resistance RθJBPW (TSSOP), 16 pinstyp 67.1 °C/W6
Junction-to-top characterization parameter ψJTPW (TSSOP), 16 pinstyp 10.8 °C/W6
Junction-to-board characterization parameter ψJBPW (TSSOP), 16 pinstyp 66.5 °C/W6
Input diode clamp voltage VIKII = –18 mA; VCC = 1.65 V to 5.5 Vmin -1.2 V6
Power-on reset voltage, VCC rising VPORRVI = VCC or GND, IO = 0typ 1.2 · max 1.5 V6
Power-on reset voltage, VCC falling VPORFVI = VCC or GND, IO = 0min 0.75 · typ 1 V6
P-port high-level output voltage VOHIOH = –8 mA; VCC = 1.65 Vmin 1.2 V6
P-port high-level output voltage VOHIOH = –8 mA; VCC = 2.3 Vmin 1.8 V6
P-port high-level output voltage VOHIOH = –8 mA; VCC = 3 Vmin 2.6 V6
P-port high-level output voltage VOHIOH = –8 mA; VCC = 4.5 Vmin 4.1 V6
P-port high-level output voltage VOHIOH = –10 mA; VCC = 1.65 Vmin 1 V6
P-port high-level output voltage VOHIOH = –10 mA; VCC = 2.3 Vmin 1.7 V6
P-port high-level output voltage VOHIOH = –10 mA; VCC = 3 Vmin 2.5 V6
P-port high-level output voltage VOHIOH = –10 mA; VCC = 4.5 Vmin 4 V6
SDA IOLVOL = 0.4 V; VCC = 1.65 V to 5.5 Vmin 3 mA6
P port IOLVOL = 0.5 V; VCC = 1.65 V to 5.5 Vmin 8 mA6
P port IOLVOL = 0.7 V; VCC = 1.65 V to 5.5 Vmin 10 mA6
INT IOLVOL = 0.4 V; VCC = 1.65 V to 5.5 Vmin 3 mA6
SCL, SDA IIVI = VCC or GND; VCC = 1.65 V to 5.5 V; limit ±1 uAmax 1 uA6
A0, A1, A2 IIVI = VCC or GND; VCC = 1.65 V to 5.5 V; limit ±1 uAmax 1 uA6
P port IIHVI = VCC; VCC = 1.65 V to 5.5 Vmax 1 uA6
P port IILVI = GND; VCC = 1.65 V to 5.5 Vmax -1 uA6
Operating mode ICCVCC = 5.5 V; VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, no loadtyp 22 · max 40 uA7
Operating mode ICCVCC = 3.6 V; VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, no loadtyp 11 · max 30 uA7
Operating mode ICCVCC = 2.7 V; VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, no loadtyp 8 · max 19 uA7
Operating mode ICCVCC = 1.95 V; VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, no loadtyp 5 · max 11 uA7
Standby mode ICCVCC = 5.5 V; VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, no loadtyp 1.5 · max 3.9 uA7
Standby mode ICCVCC = 3.6 V; VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, no loadtyp 0.9 · max 2.2 uA7
Standby mode ICCVCC = 2.7 V; VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, no loadtyp 0.6 · max 1.8 uA7
Standby mode ICCVCC = 1.95 V; VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, no loadtyp 0.4 · max 1.5 uA7
Standby mode ICCVCC = 5.5 V; VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, no loadtyp 1.5 · max 8.7 uA7
Standby mode ICCVCC = 3.6 V; VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, no loadtyp 0.9 · max 4 uA7
Standby mode ICCVCC = 2.7 V; VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, no loadtyp 0.6 · max 3 uA7
Standby mode ICCVCC = 1.95 V; VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, no loadtyp 0.4 · max 2.2 uA7
SCL CiVI = VCC or GND; VCC = 1.65 V to 5.5 Vtyp 3 · max 8 pF7
SDA CioVIO = VCC or GND; VCC = 1.65 V to 5.5 Vtyp 3 · max 9.5 pF7
P port CioVIO = VCC or GND; VCC = 1.65 V to 5.5 Vtyp 3.7 · max 9.5 pF7
I2C clock frequency fsclSTANDARD MODEmin 0 · max 100 kHz7
I2C clock high time tschSTANDARD MODEmin 4 us7
I2C clock low time tsclSTANDARD MODEmin 4.7 us7
I2C spike time tspSTANDARD MODEmax 50 ns7
I2C serial-data setup time tsdsSTANDARD MODEmin 250 ns7
I2C serial-data hold time tsdhSTANDARD MODEmin 0 ns7
I2C input rise time ticrSTANDARD MODEmax 1000 ns7
I2C input fall time ticfSTANDARD MODEmax 300 ns7
I2C output fall time tocfSTANDARD MODE; 10-pF to 400-pF busmax 300 ns7
I2C bus free time between Stop and Start tbufSTANDARD MODEmin 4.7 us7
I2C Start or repeated Start condition setup tstsSTANDARD MODEmin 4.7 us7
I2C Start or repeated Start condition hold tsthSTANDARD MODEmin 4 us7
I2C Stop condition setup tspsSTANDARD MODEmin 4 us7
Valid data time tvd(data)STANDARD MODE; SCL low to SDA output validmax 3.45 us7
Valid data time of ACK condition tvd(ack)STANDARD MODE; ACK signal from SCL low to SDA (out) lowmax 3.45 us7
I2C bus capacitive load CbSTANDARD MODEmax 400 pF7
I2C clock frequency fsclFAST MODEmin 0 · max 400 kHz7
I2C clock high time tschFAST MODEmin 0.6 us7
I2C clock low time tsclFAST MODEmin 1.3 us7
I2C spike time tspFAST MODEmax 50 ns7
I2C serial-data setup time tsdsFAST MODEmin 100 ns7
I2C serial-data hold time tsdhFAST MODEmin 0 ns7
I2C input rise time ticrFAST MODEmin 20 · max 300 ns7
I2C input fall time ticfFAST MODE; min 20 × (VDD / 5.5 V)max 300 ns7
I2C output fall time tocfFAST MODE; 10-pF to 400-pF bus; min 20 × (VDD / 5.5 V)max 300 ns7
I2C bus free time between Stop and Start tbufFAST MODEmin 1.3 us8
I2C Start or repeated Start condition setup tstsFAST MODEmin 0.6 us8
I2C Start or repeated Start condition hold tsthFAST MODEmin 0.6 us8
I2C Stop condition setup tspsFAST MODEmin 0.6 us8
Valid data time tvd(data)FAST MODE; SCL low to SDA output validmax 0.9 us8
Valid data time of ACK condition tvd(ack)FAST MODE; ACK signal from SCL low to SDA (out) lowmax 0.9 us8
I2C bus capacitive load CbFAST MODEmax 400 pF8
Interrupt valid time tivP port to INTmax 4 us8
Interrupt reset delay time tirSCL to INTmax 4 us8
Output data valid tpvSCL to P7–P0max 350 ns8
Input data setup time tpsP port to SCLmin 100 ns8
Input data hold time tphP port to SCLmin 1 us8

Pins, by the datasheet

16
1 A0
Address input. Connect directly to VCC or ground. · p. 4
2 A1
Address input. Connect directly to VCC or ground. · p. 4
3 A2
Address input. Connect directly to VCC or ground. · p. 4
4 P0
Push-pull P-port input-output; configured as an input at power on. · p. 4
5 P1
Push-pull P-port input-output; configured as an input at power on. · p. 4
6 P2
Push-pull P-port input-output; configured as an input at power on. · p. 4
7 P3
Push-pull P-port input-output; configured as an input at power on. · p. 4
8 GND
Ground. · p. 4
9 P4
Push-pull P-port input-output; configured as an input at power on. · p. 4
10 P5
Push-pull P-port input-output; configured as an input at power on. · p. 4
11 P6
Push-pull P-port input-output; configured as an input at power on. · p. 4
12 P7
Push-pull P-port input-output; configured as an input at power on. · p. 4
13 INT
Interrupt output. Connect to VCC through a pullup resistor. · p. 4
14 SCL
Serial clock bus. Connect to VCC through a pullup resistor. · p. 4
15 SDA
Serial data bus. Connect to VCC through a pullup resistor. · p. 4
16 VCC
Supply voltage. · p. 4

Open-source boards using it

32See all 32
  • 2 layers191.5 × 76 mmPcb project, the printed circuit board in 3D

    Pcb project

    CrashOverride85/zc95

    4 channel EStim box inspired by the mk312bt, with Lua scripting support

    337 parts117GPL-3.0
  • 2 layers120 × 60 mmAxis V2, the printed circuit board in 3D

    Axis V2

    Meigs2/Axis

    An open source espresso machine controller inspired by the Gaggiuinio Project

    53 parts8
  • 4 layers118.7 × 72.5 mmFramework16-m2-cellular, the printed circuit board in 3D

    Framework16-m2-cellular

    Popax21/framework16-cellular

    A M.2 cellular modem Expansion Bay module for the Framework Laptop 16

    101 parts7GPL-3.0
  • 6 layers50 × 81.3 mmBRS HW v1, the printed circuit board in 3D

    BRS HW v1

    lucasnoce/BRS_v1

    Basic Rocket System

    129 parts3MIT
  • 2 layers77.6 × 116.3 mmSolana badge, the printed circuit board in 3D

    Solana badge

    spacemandev-git/solana-defcon-badge-26

    2026 Solana Defcon Badge

    113 parts2
  • 2 layers290.1 × 175 mmRelaisAddierer, the printed circuit board in 3D

    RelaisAddierer

    apxco/Kicad

    Zum Testen von einigen Transistorschaltungen für Verstärker. Noch nicht fertig.

    262 parts
  • 6 layers102 × 41.1 mmFlight Controller, the printed circuit board in 3D

    Flight Controller

    C-yue28/Flight_Controller

    6-layer custom flight controller PCB, incorporating a battery management system (BMS), 6-axis IMU, dedicated BLDC/servo control/power lines, and camera lines. Uses the ESP32-WROOM-1 as the central microcontroller.

    139 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TCA9534PW?

Yes. The symbol is Interface_Expansion:TCA9534 and the footprint Package_SO:TSSOP-16_4.4x5mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TCA9534PW?

TSSOP-16, with 16 pins. Its footprint is drawn on this page.

Where is the TCA9534PW datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TCA9534PW?

JLCPCB lists it as part C783615, with 9,058 in stock; the sellers' links on this page open their listings.

What can replace the TCA9534PW?

Parts like it in the library: the PCA9554PW by NXP Semiconductors, the PCA9557PW by NXP Semiconductors, the TCA9534APW by Texas Instruments and the TCA9554PW by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TCA9534PW?

32 boards in 26 repositories on GitHub; the most starred are listed on this page, with their KiCad files.