Skip to the content
123456789

LMR38020SDDA

Texas InstrumentsExtended

-40℃~+150℃@(TJ) 1 1V~75V 2.2MHz 2A 4.2V~80V 40uA Adjustable Buck Buck Built-in Yes SOP-8-EP DC-DC Converters ROHS

Part id
ti/LMR38020SDDA
Category
DC DC Converters
Package
SOP-8-EP
Pins
9
In stock
5,158 at JLCPCB (C3192337)

Overview

The LMR38020SDDA is a DC DC Converter made by Texas Instruments in a SOP-8-EP package with 9 pins. -40℃~+150℃@(TJ) 1 1V~75V 2.2MHz 2A 4.2V~80V 40uA Adjustable Buck Buck Built-in Yes SOP-8-EP DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:LMR38010FSDDAR, from EasyEDA) and its footprint (EasyEDA_Cloud:SOP-8_L4.9-W3.9-P1.27-LS6.0-BL-EP-2, from EasyEDA), ready for a KiCad board. 5,158 are in stock at JLCPCB (part C3192337).

Symbol

1GND2EN3VIN4RT/SYNC5FB6PG7BOOT8SW9EP
EasyEDA_Cloud:LMR38010FSDDARFrom EasyEDA

Footprint

123456789
EasyEDA_Cloud:SOP-8_L4.9-W3.9-P1.27-LS6.0-BL-EP-2From EasyEDA

From the datasheet

14
Supply, least
4.2 V · VIN, recommended operating min after start-up · p. 4
Supply, most
80 V · VIN, recommended operating max after start-up · p. 4
Supply, absolute maximum
85 V · VIN to PGND, absolute max · p. 4
Junction, hottest
150 °C · junction temperature absolute max · p. 4
Takes working
40 µA · typical non-switching quiescent current, VEN = 3.3 V, PFM · p. 5
Takes asleep
3 µA · typical shutdown current at VIN, VEN = 0 V · p. 5
Gives
2 A · max continuous output DC current · p. 4
Current limit
3.2 A · typical high-side current limit · p. 5
Feedback reference
1 V · feedback reference, nominal · p. 10
Switches at
525 kHz · typical switching frequency, RT = 49.9 kΩ · p. 5
Junction to air (DDA (HSOIC))
42.9 K/W · junction-to-ambient thermal resistance · p. 5
Junction to air (DDA (HSOIC))
29 K/W · junction-to-ambient thermal resistance with TI EVM board · p. 5
Junction to case (DDA (HSOIC))
54 K/W · junction-to-case top thermal resistance · p. 5
Junction to board (DDA (HSOIC))
13.6 K/W · junction-to-board thermal resistance · p. 5

What it is and has

11
Functional safety
Functional Safety-Capable · p. 1
Input voltage range
4.2 V to 80 V · p. 1
Continuous output current
2 A · p. 1
Frequency synchronization
External clock · p. 1
Synchronous rectification
Integrated · p. 1
Protection
Thermal shutdown · p. 9
Protection
VIN undervoltage lockout · p. 9
Protection
Cycle-by-cycle current limit · p. 9
Protection
Hiccup mode short-circuit protection · p. 9
Package
DDA (HSOIC, 8), 4.89 mm × 3.90 mm · p. 1
Operating mode and spread spectrum
PFM, spread spectrum enabled · p. 3

Around it

2
cap 100 nF
between BOOT and SW; High-quality bootstrap capacitor for the internal high-side driver. · p. 3
res 10 kΩ to 100 kΩ
between VOUT and FB; Recommended RFBT range for most applications; use 1% tolerance resistors with low temperature coefficient. · p. 10

Specifications

68
ParameterConditionsAs printedPage
Input voltageVIN to PGNDmin -0.3 · max 85 V4
Input voltageEN to PGND; maximum VIN+0.3 Vmin -0.3 V4
Input voltageFB to PGNDmin -0.3 · max 5.5 V4
Input voltageRT/SYNC to PGNDmin -0.3 · max 5.5 V4
Output voltageBOOT to SWmin -0.3 · max 5.5 V4
Output voltageSW to PGNDmin -0.3 · max 85 V4
Output voltageSW to PGND less than 10-ns transientsmin -5 · max 85.3 V4
Output voltagePGOOD to PGNDmin -0.3 · max 20 V4
Junction Temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; value ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per ANSI/ESDA/JEDEC JS-002; value ±500 Vmax 500 V4
Input voltageInput voltage range after start-upmin 4.2 · max 80 V4
Input voltageRT to PGNDmax 5 V4
Input voltagePGOOD to PGNDmax 20 V4
Output voltageSW to PGNDmax 80 V4
Output voltageOutput voltage range for adjustable versionmin 1 · max 75 V4
FrequencyFrequency adjustment rangemin 200 · max 2200 kHz4
Sync frequencySynchronization frequency rangemin 300 · max 2100 kHz4
Load currentOutput DC current range LMR38020min 0 · max 2 A4
Temperature TJOperating junction temperature rangemin -40 · max 150 °C4
Junction-to-ambient thermal resistance RθJALMR38020, DDA (HSOIC), 8 PINStyp 42.9 °C/W5
Junction-to-ambient thermal resistance with TI EVM board RθJA(Effecitve)LMR38020, DDA (HSOIC), 8 PINStyp 29 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)LMR38020, DDA (HSOIC), 8 PINStyp 54 °C/W5
Junction-to-board thermal resistance RθJBLMR38020, DDA (HSOIC), 8 PINStyp 13.6 °C/W5
Junction-to-top characterization parameter ψJTLMR38020, DDA (HSOIC), 8 PINStyp 4.3 °C/W5
Junction-to-board characterization parameter ψJBLMR38020, DDA (HSOIC), 8 PINStyp 13.8 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)LMR38020, DDA (HSOIC), 8 PINStyp 4.3 °C/W5
Input operating voltage VIN_OPERATENeeded to start upmax 4.2 V5
Input operating voltage VIN_OPERATEOnce operatingmax 3.8 V5
Non-switching quiescent current IQ(Non-SW)VEN = 3.3 V (PFM variant only)typ 40 uA5
Shutdown quiescent current; measured at VIN pin ISDVEN = 0 Vtyp 3 · max 10 uA5
Enable input high level VEN-HVEN risingmin 1.1 · typ 1.25 · max 1.4 V5
Enable input low level VEN-LVEN fallingmin 0.95 · typ 1.1 · max 1.22 V5
Enable input leakage current ILKG-ENVEN = 3.3Vtyp 5 nA5
High-side current limit IHS-LIMIT2A Versionmin 2.6 · typ 3.2 · max 3.8 A5
Low-side current limit ILS-LIMIT2A Versionmin 1.8 · typ 2.3 · max 2.8 A5
Zero cross detector threshold IL-ZCPFM variants onlytyp 0.01 A5
Minimum inductor peak current IPEAK-MIN2A Version, PFM variants onlytyp 0.5 A5
High-side MOSFET ON-resistance RDS-ON-HStyp 303 mΩ5
Low-side MOSFET ON-resistance RDS-ON-LStyp 133 mΩ5
Minimum switch on-time tON-MINVIN =24 V, Iout = 1 Atyp 80 · max 131 ns5
Minimum switch off-time tOFF-MINtyp 190 · max 300 ns5
Maximum switch on-time tON-MAXtyp 5 us5
Switching frequency FOSCRT = 49.9 kΩmin 430 · typ 525 · max 650 kHz5
Spread of internal oscillator with Spread Spectrum Enabled FSPREADmin -8 · max 8 %6
SYNC clock high level threshold VSYNC_HImax 2 V6
SYNC clock low level threshold VSYNC_LOmin 0.6 V6
High duration needed to be recognized as a pulse tPULSE_Hmax 50 ns6
Time needed for clock to lock to a valid synchronization signal in sync cycles CLOCKmax 230 us6
Internal soft-start time tSStyp 4 ms6
Power-Good upper threshold - rising VPG-HIGH-UP% of FB voltagemin 110 · typ 112 · max 114 %6
Power-Good lower threshold - falling VPG-LOW-DN% of FB voltagemin 90 · typ 92 · max 94 %6
Power-Good hysteresis (rising & falling) VPG-HYS% of FB voltagetyp 2.2 %6
Minimum input voltage for proper Power-Good function VPG-VALIDmax 2 V6
Power-Good on-resistance RPGVEN = 0 Vtyp 140 Ω6
Power-Good on-resistance RPGVEN = 3.3Vtyp 92 Ω6
Glitch filter time constant for PGOOD function tPGDFLT(fall)typ 40 us6
Thermal shutdown TSD-RisingShutdown thresholdtyp 163 ℃6
Thermal shutdown TSD-FallingRecovery thresholdtyp 150 ℃6
Operating input voltage range VINmin 4.2 · max 80 V7
Adjustable output voltage regulation VOUTPFM operationmin -1.5 · max 2.5 %7
Input supply current when in regulation ISUPPLYVIN = 24 V, VOUT = 3.3 V, IOUT = 0 A, RFBT = 1 MΩ, PFM varianttyp 40 uA7
Maximum switch duty cycle DMAXtyp 97 %7
FB pin voltage required to trip short-circuit hiccup mode VHCtyp 0.4 V7
Switch voltage dead time tDtyp 5 ns7
Thermal shutdown temperature TSDShutdown temperaturetyp 163 °C7
Thermal shutdown temperature TSDRecovery temperaturetyp 150 °C7

Pins, by the datasheet

9
1 GND
Power and analog ground; connect a high-quality bypass capacitor directly between GND and VIN with short, wide traces. · p. 3
2 EN
Enable input, high ON and low OFF; may connect directly to VIN; do not float. · p. 3
3 VIN
Input supply; connect high-quality bypass capacitors directly between VIN and GND with short, wide traces. · p. 3
4 RT/SYNC
Resistor timing or external clock input; a resistor to ground sets switching frequency, or an external clock synchronizes the internal PLL. · p. 3
5 FB
Feedback input; connect to the feedback divider tap; do not float or ground. · p. 3
6 PG
Power-good output; pull up to a suitable supply through a current limiting resistor; low when EN is low; may be left open if unused. · p. 3
7 BOOT
Bootstrap supply for the high-side driver; connect a high-quality 100-nF capacitor to SW. · p. 3
8 SW
Regulator switch node; connect to a power inductor. · p. 3
THERMAL PAD EP
Connect to system ground. · p. 3

Ordering codes, by the datasheet

3
LMR38020SDDAR
DDA (HSOIC, 8) · 2 A, FPWM disabled, spread spectrum enabled · p. 3
LMR38020FDDAR
DDA (HSOIC, 8) · 2 A, FPWM enabled, spread spectrum disabled · p. 3
LMR38020FSDDAR
DDA (HSOIC, 8) · 2 A, FPWM enabled, spread spectrum enabled · p. 3

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the LMR38020SDDA?

Yes. The symbol is EasyEDA_Cloud:LMR38010FSDDAR and the footprint EasyEDA_Cloud:SOP-8_L4.9-W3.9-P1.27-LS6.0-BL-EP-2, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LMR38020SDDA?

SOP-8-EP, with 9 pins. Its footprint is drawn on this page.

Where is the LMR38020SDDA datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LMR38020SDDA?

JLCPCB lists it as part C3192337, with 5,158 in stock; the sellers' links on this page open their listings.

What can replace the LMR38020SDDA?

Parts like it in the library: the LM5013DDA by Texas Instruments, the LMR38020FDDA by Texas Instruments, the HT7180SPER by Jiaxing Heroic Elec Tech and the JW5116FESOP#TRPBF by JoulWatt Tech. Check their datasheets: a part that fits the footprint may still differ in its ratings.