Skip to the content
123456789999

LMR38010SDDA

Texas InstrumentsExtended

-40℃~+150℃@(TJ) 1 1A 200kHz~2.2MHz 4.2V~80V 40uA Adjustable Buck Buck Built-in Yes SOPowerPAD-8 DC-DC Converters ROHS

Part id
ti/LMR38010SDDA
Category
DC DC Converters
Package
SOPowerPAD-8
Pins
9
In stock
2,493 at JLCPCB (C5219310)
Used on
1 open-source board

Overview

The LMR38010SDDA is a DC DC Converter made by Texas Instruments in a SOPowerPAD-8 package with 9 pins. -40℃~+150℃@(TJ) 1 1A 200kHz~2.2MHz 4.2V~80V 40uA Adjustable Buck Buck Built-in Yes SOPowerPAD-8 DC-DC Converters ROHS.

PCBKit's library has its footprint (Package_SO:TI_SO-PowerPAD-8, from KiCad's library), ready for a KiCad board. 2,493 are in stock at JLCPCB (part C5219310). 1 open-source board in 1 repository on GitHub use it.

Symbol

The library has no symbol for this part yet.

Footprint

123456789999
Package_SO:TI_SO-PowerPAD-8From KiCad's library

From the datasheet

14
Supply, least
4.2 V · VIN, recommended operating minimum after start-up · p. 4
Supply, most
80 V · VIN, recommended operating maximum after start-up · p. 4
Supply, absolute maximum
85 V · VIN, absolute maximum to PGND · p. 4
Junction, hottest
150 °C · maximum junction temperature · p. 4
Takes working
40 µA · VIN, typical input supply current in regulation, PFM, no load · p. 7
Takes asleep
3 µA · VIN, typical shutdown current, VEN = 0 V · p. 5
Gives
1 A · maximum continuous output DC current · p. 4
Current limit
1.6 A · typical high-side current limit · p. 5
Feedback reference
1 V · typical adjustable-output reference · p. 10
Switches at
525 kHz · typical switching frequency, RT = 49.9 kΩ · p. 5
Junction to air (DDA (HSOIC))
42.9 K/W · junction-to-ambient thermal resistance · p. 5
Junction to air (DDA (HSOIC))
29 K/W · junction-to-ambient thermal resistance with TI EVM board · p. 5
Junction to case (DDA (HSOIC))
54 K/W · junction-to-case top thermal resistance · p. 5
Junction to board (DDA (HSOIC))
13.6 K/W · junction-to-board thermal resistance · p. 5

What it is and has

9
Functional safety
Functional Safety-Capable · p. 1
Switching frequency range
200 kHz to 2.2 MHz, adjustable · p. 1
Synchronization
External clock · p. 1
Operating mode and spread spectrum
PFM, spread spectrum enabled · p. 3
Protection
Thermal shutdown · p. 9
Protection
VIN undervoltage lockout · p. 9
Protection
Cycle-by-cycle current limit · p. 9
Protection
Hiccup mode short-circuit protection · p. 9
Package
DDA (HSOIC, 8), 4.89 mm × 3.90 mm · p. 1

Around it

2
cap 100-nF
between BOOT and SW; High-quality bootstrap capacitor for the internal high-side driver. · p. 3
res 10 kΩ to 100 kΩ
between VOUT and FB; Recommended RFBT range for most applications; use 1% tolerance, low temperature coefficient feedback divider resistors. · p. 10

Specifications

69
ParameterConditionsAs printedPage
Input voltageVIN to PGNDmin -0.3 · max 85 V4
Input voltageEN to PGND; maximum VIN+0.3 Vmin -0.3 V4
Input voltageFB to PGNDmin -0.3 · max 5.5 V4
Input voltageRT/SYNC to PGNDmin -0.3 · max 5.5 V4
Input voltageBOOT to SWmin -0.3 · max 5.5 V4
Output voltageSW to PGNDmin -0.3 · max 85 V4
Output voltageSW to PGND less than 10-ns transientsmin -5 · max 85.3 V4
Output voltagePGOOD to PGNDmin -0.3 · max 20 V4
Junction Temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; magnitude of ± ratingmax 2000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per ANSI/ESDA/JEDEC JS-002; magnitude of ± ratingmax 500 V4
Input voltageInput voltage range after start-upmin 4.2 · max 80 V4
Input voltageRT to PGNDmax 5 V4
Input voltagePGOOD to PGNDmax 20 V4
Output voltageSW to PGNDmax 80 V4
Output voltageOutput voltage range for adjustable versionmin 1 · max 75 V4
FrequencyFrequency adjustment rangemin 200 · max 2200 kHz4
Sync frequencySynchronization frequency rangemin 300 · max 2100 kHz4
Load currentOutput DC current range LMR38010min 0 · max 1 A4
Temperature TJOperating junction temperature rangemin -40 · max 150 °C4
Junction-to-ambient thermal resistance RθJALMR38010, DDA (HSOIC), 8 PINStyp 42.9 °C/W5
Junction-to-ambient thermal resistance with TI EVM board RθJA(Effecitve)LMR38010, DDA (HSOIC), 8 PINStyp 29 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)LMR38010, DDA (HSOIC), 8 PINStyp 54 °C/W5
Junction-to-board thermal resistance RθJBLMR38010, DDA (HSOIC), 8 PINStyp 13.6 °C/W5
Junction-to-top characterization parameter ψJTLMR38010, DDA (HSOIC), 8 PINStyp 4.3 °C/W5
Junction-to-board characterization parameter ψJBLMR38010, DDA (HSOIC), 8 PINStyp 13.8 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)LMR38010, DDA (HSOIC), 8 PINStyp 4.3 °C/W5
Input operating voltage VIN_OPERATENeeded to start upmax 4.2 V5
Input operating voltage VIN_OPERATEOnce operatingmax 3.8 V5
Non-switching quiescent current IQ(Non-SW)VEN = 3.3 V (PFM variant only); VIN = 24 Vtyp 40 uA5
Shutdown quiescent current; measured at VIN pin ISDVEN = 0 V; VIN = 24 Vtyp 3 · max 10 uA5
Enable input high level VEN-HVEN rising; VIN = 24 Vmin 1.1 · typ 1.25 · max 1.4 V5
Enable input low level VEN-LVEN falling; VIN = 24 Vmin 0.95 · typ 1.1 · max 1.22 V5
Enable input leakage current ILKG-ENVEN = 3.3V; VIN = 24 Vtyp 5 nA5
High-side current limit IHS-LIMIT1A Version; VIN = 24 Vmin 1.3 · typ 1.6 · max 1.9 A5
Low-side current limit ILS-LIMIT1A Version; VIN = 24 Vmin 0.9 · typ 1.2 · max 1.5 A5
Zero cross detector threshold IL-ZCPFM variants only; VIN = 24 Vtyp 0.01 A5
Minimum inductor peak current IPEAK-MIN1A Version, PFM variants only; VIN = 24 Vtyp 0.25 A5
High-side MOSFET ON-resistance RDS-ON-HSVIN = 24 Vtyp 303 mΩ5
Low-side MOSFET ON-resistance RDS-ON-LSVIN = 24 Vtyp 133 mΩ5
Minimum switch on-time tON-MINVIN =24 V, Iout = 1 Atyp 80 · max 131 ns5
Minimum switch off-time tOFF-MINVIN = 24 Vtyp 190 · max 300 ns5
Maximum switch on-time tON-MAXVIN = 24 Vtyp 5 us5
Switching frequency FOSCRT = 49.9 kΩ; VIN = 24 Vmin 430 · typ 525 · max 650 kHz5
Spread of internal oscillator with Spread Spectrum Enabled FSPREADVIN = 24 Vmin -8 · max 8 %6
SYNC clock high level threshold VSYNC_HIVIN = 24 Vmax 2 V6
SYNC clock low level threshold VSYNC_LOVIN = 24 Vmin 0.6 V6
High duration needed to be recognized as a pulse tPULSE_HVIN = 24 Vmax 50 ns6
Time needed for clock to lock to a valid synchronization signal in sync cycles CLOCKVIN = 24 Vmax 230 us6
Internal soft-start time tSSVIN = 24 Vtyp 4 ms6
Power-Good upper threshold - rising VPG-HIGH-UP% of FB voltage; VIN = 24 Vmin 110 · typ 112 · max 114 %6
Power-Good lower threshold - falling VPG-LOW-DN% of FB voltage; VIN = 24 Vmin 90 · typ 92 · max 94 %6
Power-Good hysteresis (rising & falling) VPG-HYS% of FB voltage; VIN = 24 Vtyp 2.2 %6
Minimum input voltage for proper Power-Good function VPG-VALIDmax 2 V6
Power-Good on-resistance RPGVEN = 0 V; VIN = 24 Vtyp 140 Ω6
Power-Good on-resistance RPGVEN = 3.3V; VIN = 24 Vtyp 92 Ω6
Glitch filter time constant for PGOOD function tPGDFLT(fall)VIN = 24 Vtyp 40 us6
Thermal shutdown TSD-RisingShutdown thresholdtyp 163 ℃6
Thermal shutdown TSD-FallingRecovery thresholdtyp 150 ℃6
Operating input voltage range VINTypical application circuit with nominal component valuesmin 4.2 · max 80 V7
Adjustable output voltage regulation VOUTPFM operationmin -1.5 · max 2.5 %7
Input supply current when in regulation ISUPPLYVIN = 24 V, VOUT = 3.3 V, IOUT = 0 A, RFBT = 1 MΩ, PFM varianttyp 40 uA7
Maximum switch duty cycle DMAXTypical application circuit with nominal component valuestyp 97 %7
FB pin voltage required to trip short-circuit hiccup mode VHCTypical application circuit with nominal component valuestyp 0.4 V7
Switch voltage dead time tDTypical application circuit with nominal component valuestyp 5 ns7
Frequency span of spread spectrum operation FsSSSymmetric ±4% spanmin -4 · max 4 %7
Thermal shutdown temperature TSDShutdown temperaturetyp 163 °C7
Thermal shutdown temperature TSDRecovery temperaturetyp 150 °C7

Pins, by the datasheet

9
1 GND
Power and analog ground; connect a high-quality bypass capacitor directly between GND and VIN with short, wide traces. · p. 3
2 EN
Enable input: high turns regulator on, low turns it off; may connect directly to VIN; do not float. · p. 3
3 VIN
Input supply; connect high-quality bypass capacitors directly to GND with short, wide traces. · p. 3
4 RT/SYNC
Connect a resistor to ground to set switching frequency, or apply an external clock for synchronization; returns to resistor programming if clock edges stop. · p. 3
5 FB
Feedback input; connect to the feedback divider tap; do not float or ground. · p. 3
6 PG
Power-good flag; pull up through a current-limiting resistor; high indicates power OK, low power bad; pulls low when EN is low; may be left open if unused. · p. 3
7 BOOT
Bootstrap supply for the internal high-side driver; connect a high-quality 100-nF capacitor to SW. · p. 3
8 SW
Regulator switch node; connect to a power inductor. · p. 3
EP EP
Thermal pad; connect to system ground. · p. 3

Ordering codes, by the datasheet

1
LMR38010SDDAR
DDA (HSOIC, 8) · 1 A, FPWM No, spread spectrum Yes · p. 3

Open-source boards using it

1
  • 4 layers100 × 100 mmTtf ng a v1, the printed circuit board in 3D

    Ttf ng a v1

    gingerologist/ttf-ng-a-v1

    kicad 10 project for board A for ttf project, release.

    209 parts

Parts like it

2

Questions

Is there a KiCad symbol and footprint for the LMR38010SDDA?

Yes. the footprint Package_SO:TI_SO-PowerPAD-8, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LMR38010SDDA?

SOPowerPAD-8, with 9 pins. Its footprint is drawn on this page.

Where is the LMR38010SDDA datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LMR38010SDDA?

JLCPCB lists it as part C5219310, with 2,493 in stock; the sellers' links on this page open their listings.

What can replace the LMR38010SDDA?

Parts like it in the library: the TPS5430DDA by Texas Instruments and the TPS5430DDARG4 by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the LMR38010SDDA?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.