Skip to the content
123456789101112131415

LM3150MHX

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 12A 1MHz 6V~42V Adjustable Buck Buck External Yes HTSSOP-14-EP DC-DC Converters ROHS

Part id
ti/LM3150MHX
Category
DC DC Converters
Package
HTSSOP-14-EP
Pins
15
In stock
6,659 at JLCPCB (C48112)
Used on
1 open-source board

Overview

The LM3150MHX is a DC DC Converter made by Texas Instruments in a HTSSOP-14-EP package with 15 pins. -40℃~+125℃@(TJ) 1 12A 1MHz 6V~42V Adjustable Buck Buck External Yes HTSSOP-14-EP DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:LM3150MH, from KiCad's library) and its footprint (Package_SO:Texas_HTSSOP-14-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask3.155x3.255mm, from KiCad's library), ready for a KiCad board. 6,659 are in stock at JLCPCB (part C48112). 1 open-source board in 1 repository on GitHub use it.

Symbol

1VCC2VIN3EN4FB5SGND6SS7RON8ILIM10SW11HG12BST13LG14PGND
Regulator_Switching:LM3150MHFrom KiCad's library

Footprint

123456789101112131415
Package_SO:Texas_HTSSOP-14-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask3.155x3.255mmFrom KiCad's library

From the datasheet

10
Supply, least
6 V · VIN, recommended operating min · p. 4
Supply, most
42 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
47 V · VIN, absolute max · p. 4
Junction, hottest
125 °C · operating junction temperature max · p. 4
Takes working
3.5 mA · VIN operating current typical, no switching, VFB = 1 V · p. 5
Takes asleep
32 µA · VIN shutdown current typical, VEN = 0 V · p. 5
Feedback reference
600 mV · FB regulation reference typical, VSS > 0.6 V · p. 5
Junction to air (PWP)
42.5 K/W · junction-to-ambient thermal resistance · p. 4
Junction to case (PWP)
28.7 K/W · junction-to-case top thermal resistance · p. 4
Junction to board (PWP)
24.2 K/W · junction-to-board thermal resistance · p. 4

What it is and has

7
Controller
Wide-VIN synchronous buck controller · p. 1
Control architecture
Constant on-time (COT) · p. 1
Output capacitors
Stable with low ESR capacitors · p. 1
Startup
Output voltage prebias startup · p. 1
Current limit
Valley current limit · p. 1
Soft-start
Programmable · p. 1
Package
HTSSOP (14), 5.00 mm × 4.40 mm · p. 1

Around it

3
cap 1.0-µF to 4.7-µF
between VCC and GND; FET driver supply decoupling capacitor. · p. 3
cap 0.33 to 0.47-µF
between BST and SW; Bootstrap capacitor; charged by the internal diode during high-side switch off-time. · p. 3
cap 1-nF
between EN and GND; May be necessary with an open drain connection to EN to decouple noise and prevent false disabling. · p. 13

Specifications

57
ParameterConditionsAs printedPage
VIN, RON to GNDover operating free-air temperature rangemin -0.3 · max 47 V4
SW to GNDover operating free-air temperature rangemin -3 · max 47 V4
BST to SWover operating free-air temperature rangemin -0.3 · max 7 V4
BST to GNDover operating free-air temperature rangemin -0.3 · max 52 V4
All Other Inputs to GNDover operating free-air temperature rangemin -0.3 · max 7 V4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±2000 Vmax 2000 V4
VINover operating free-air temperature rangemin 6 · max 42 V4
Junction Temperature Range (TJ) TJmin -40 · max 125 °C4
ENover operating free-air temperature rangemin 0 · max 5 V4
Junction-to-ambient thermal resistance RθJALM3150, PWP, 14 PINStyp 42.5 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)LM3150, PWP, 14 PINStyp 28.7 °C/W4
Junction-to-board thermal resistance RθJBLM3150, PWP, 14 PINStyp 24.2 °C/W4
Junction-to-top characterization parameter ψJTLM3150, PWP, 14 PINStyp 0.9 °C/W4
Junction-to-board characterization parameter ψJBLM3150, PWP, 14 PINStyp 23.9 °C/W4
Junction-to-case (bottom) thermal resistance RθJC(bot)LM3150, PWP, 14 PINStyp 4.4 °C/W4
VCC VCCCVCC = 1 uF, 0 mA to 40 mA; TJ = 25°Ctyp 5.95 V5
VCC VCCCVCC = 1 uF, 0 mA to 40 mA; TJ = -40°C to 125°Cmin 5.65 · max 6.25 V5
VIN - VCC Dropout Voltage VIN - VCCIVCC = 2 mA, VIN = 5.5 V; TJ = 25°Ctyp 40 mV5
VIN - VCC Dropout Voltage VIN - VCCIVCC = 30 mA, VIN = 5.5 V; TJ = 25°Ctyp 330 mV5
VCC Current Limit (1) IVCCLVCC = 0V; TJ = 25°Ctyp 100 mA5
VCC Current Limit (1) IVCCLVCC = 0V; TJ = -40°C to 125°Cmin 65 mA5
VCC Undervoltage Lockout Threshold (UVLO) VCCUVLOVCC Increasing; TJ = 25°Ctyp 5.1 V5
VCC Undervoltage Lockout Threshold (UVLO) VCCUVLOVCC Increasing; TJ = -40°C to 125°Cmin 4.75 · max 5.4 V5
VCC UVLO Hysteresis VCCUVLO-HYSVCC Decreasing; TJ = 25°Ctyp 475 mV5
VCC UVLO Filter Delay tCC-UVLO-DTJ = 25°Ctyp 3 us5
Input Operating Current IINNo Switching, VFB = 1 V; TJ = 25°Ctyp 3.5 mA5
Input Operating Current IINNo Switching, VFB = 1 V; TJ = -40°C to 125°Cmax 5 mA5
Input Operating Current, Device Shutdown IIN-SDVEN = 0 V; TJ = 25°Ctyp 32 uA5
Input Operating Current, Device Shutdown IIN-SDVEN = 0 V; TJ = -40°C to 125°Cmax 55 uA5
Boost Pin Leakage IQ-BSTVBST – VSW = 6 V; TJ = 25°Ctyp 2 nA5
HG Drive Pullip On-Resistance RDS-HG-Pull-UpIHG Source = 200 mA; TJ = 25°Ctyp 5 Ω5
HG Drive Pulldown On-Resistance RDS-HG-Pull-DownIHG Sink = 200 mA; TJ = 25°Ctyp 3.4 Ω5
LG Drive Pullup On-Resistance RDS-LG-Pull-UpILG Source = 200 mA; TJ = 25°Ctyp 3.4 Ω5
LG Drive Pulldown On-Resistance RDS-LG-Pull-DownILG Sink = 200 mA; TJ = 25°Ctyp 2 Ω5
SS Pin Source Current ISSVSS = 0 V; TJ = 25°Ctyp 7.7 uA5
SS Pin Source Current ISSVSS = 0 V; TJ = -40°C to 125°Cmin 5.9 · max 9.5 uA5
SS Pin Discharge Current ISS-DISCurrent Limit; TJ = 25°Ctyp 200 uA5
Current Limit Sense Pin Source Current ILIM-THTJ = 25°Cmin 75 · typ 85 · max 95 uA5
ON Timer Pulse Width tONVIN = 10V, RON = 100 kΩ, VFB = 0.6V; TJ = 25°Ctyp 1.02 us5
ON Timer Pulse Width tONVIN = 18V, RON = 100 kΩ, VFB = 0.6 V; TJ = 25°Ctyp 0.62 us5
ON Timer Pulse Width tONVIN = 42 V, RON = 100 kΩ, VFB = 0.6 V; TJ = 25°Ctyp 0.36 us5
ON Timer Minimum Pulse Width tON-MINSee (2); TJ = 25°Ctyp 200 ns5
OFF Timer Minimum Pulse Width tOFFTJ = 25°Ctyp 370 ns5
OFF Timer Minimum Pulse Width tOFFTJ = -40°C to 125°Cmax 525 ns5
EN Pin Input Threshold Trip Point VENVEN Rising; TJ = 25°Ctyp 1.2 V5
EN Pin Input Threshold Trip Point VENVEN Rising; TJ = -40°C to 125°Cmin 1.14 · max 1.26 V5
EN Pin Threshold Hysteresis VEN-HYSVEN Falling; TJ = 25°Ctyp 120 mV5
In-Regulation Feedback Voltage VFBVSS > 0.6 V; TJ = 25°Ctyp 0.6 V5
In-Regulation Feedback Voltage VFBVSS > 0.6 V; TJ = -40°C to 125°Cmin 0.588 · max 0.612 V5
Feedback Overvoltage Threshold VFB-OVTJ = 25°Ctyp 0.72 V5
Feedback Overvoltage Threshold VFB-OVTJ = -40°C to 125°Cmin 0.69 · max 0.748 V5
Feedback Bias Current IFBTJ = 25°Ctyp 20 nA5
Forward Voltage VfBoost diode; IBST = 2 mA; TJ = 25°Ctyp 0.7 V6
Forward Voltage VfBoost diode; IBST = 30 mA; TJ = 25°Ctyp 1 V6
Thermal Shutdown TSDRisingtyp 165 °C6
Thermal Shutdown Hysteresis TSDFallingtyp 15 °C6

Pins, by the datasheet

15
1 VCC
Supply for FET drivers, nominally regulated to 5.95 V; connect a 1.0-uF to 4.7-uF decoupling capacitor to ground. · p. 3
2 VIN
Input supply to the device; nominal input range is 6 V to 42 V. · p. 3
3 EN
Enable by applying a logic high greater than 1.26 V typical or leaving floating; ground to disable. · p. 3
4 FB
Feedback to regulation, overvoltage and short-circuit comparators; connect to the output-to-ground feedback divider for a 0.6-V regulation setting. · p. 3
5 SGND
Ground for internal bias and reference circuitry; connect to PGND at a single point. · p. 3
6 SS
Soft-start pin; an internal 7.7-uA source charges an external capacitor. · p. 3
7 RON
Connect an external resistor from VIN to set high-side switch on-time. · p. 3
8 ILIM
Monitors low-side switch current and triggers valley current limiting at the level set by RLIM and the sourced sense current. · p. 3
9 SGND
Ground for internal bias and reference circuitry; connect to PGND at a single point. · p. 3
10 SW
Switch node and high-gate driver lower supply rail; connect the boost capacitor between SW and BST. · p. 3
11 HG
High-side NMOS gate drive, supplied by the differential voltage between BST and SW. · p. 3
12 BST
High-gate driver upper supply rail; connect a 0.33 to 0.47-uF capacitor to SW and do not connect to an external supply rail. · p. 3
13 LG
Low-side NMOS gate drive, supplied by VCC. · p. 3
14 PGND
Synchronous rectifier MOSFET source connection; tie to the power ground plane and to SGND at a single point. · p. 3
EP EP
Exposed die attach pad; connect directly to SGND to help dissipate heat. · p. 3

Open-source boards using it

1

Parts like it

4

Questions

Is there a KiCad symbol and footprint for the LM3150MHX?

Yes. The symbol is Regulator_Switching:LM3150MH and the footprint Package_SO:Texas_HTSSOP-14-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask3.155x3.255mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LM3150MHX?

HTSSOP-14-EP, with 15 pins. Its footprint is drawn on this page.

Where is the LM3150MHX datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LM3150MHX?

JLCPCB lists it as part C48112, with 6,659 in stock; the sellers' links on this page open their listings.

What can replace the LM3150MHX?

Parts like it in the library: the LM3150MH by Texas Instruments, the LM3150MHE by Texas Instruments, the LM5156HPWP by Texas Instruments and the LM51561HPWP by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the LM3150MHX?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.