Skip to the content
PCBKitNew board

LM2901

Texas Instruments

ti/LM2901
Category
Uncategorised
Pins
14

Overview

The LM2901 is an uncategorised made by Texas Instruments with 14 pins.

PCBKit's library has its KiCad symbol (Comparator:LM2901, from KiCad's library), ready for a KiCad board. 14 open-source boards in 14 repositories on GitHub use it.

Symbol

2-4+5
Comparator:LM2901From KiCad's library

Footprint

The library has no footprint for this part yet.

Pinout

14
The pins of the LM2901
PinNameType
1—Open collector
2—Open collector
3V+Power in
4-Input
5+Input
6-Input
7+Input
8-Input
9+Input
10-Input
11+Input
12V-Power in
13—Open collector
14—Open collector

Open-source boards using it

All 14
  • 2 layers300 × 53 mmBMW E30 VFL SI Board, the printed circuit board in 3D

    BMW E30 VFL SI Board

    FabianGmeiner/BMW_E30_SI_Board

    Reverse engineering and improving the BMW E30 service indicator board

    112 parts20GPL-3.0
  • 4 layers180 × 120 mmMG ZS V2, the printed circuit board in 3D

    MG ZS V2

    damienmaguire/MG-EV-Inverter

    Reverse engineering of the drive motor and inverter used in MG Electric Vehicles

    177 parts17GPL-3.0
  • 2 layers85 × 50 mmDataAcquisitionUnit, the printed circuit board in 3D

    DataAcquisitionUnit

    RobertGawron/HardwareDataLogger

    Data logger shield based on STM32+ESP32. Has: LCD, keyboard, WIFi, UART and SD card for data storage. Input is as pulse counter and UART communication.

    70 parts6MIT
  • 4 layers64 × 43 mmUAV HWE Design, the printed circuit board in 3D

    UAV HWE Design

    fuchs-harry/UAV_Hardware_Design

    96 parts3MIT
  • 6 layers268 × 230 mmRf board, the printed circuit board in 3D

    Rf board

    PE1RGU/hf-antenna-switch

    Remote HF antenna switch: 3 radios x 4 antennas (path to 8), outdoor relay unit with a hardware safety chain, controlled over Cat6 from a shack interface. KiCad 10, open hardware, designed together with an AI.

    357 parts2CERN-OHL-S-2.0
  • 2 layers79.7 × 80 mmMainboardv1.2, the printed circuit board in 3D

    Mainboardv1.2

    doobedoobedo/Huebner_Inverter

    KiCAD port of https://github.com/jsphuebner/inverter-hardware mainboard V1.2

    133 parts1
  • 4 layers100 × 99.4 mmMPPT V3, the printed circuit board in 3D

    MPPT V3

    hazzalemon/MPPTV3_board

    3rd revision of the MPPT solar charge controller PCB design

    204 parts1
  • 2 layers148.6 × 83.8 mmNew BSPD, the printed circuit board in 3D

    New BSPD

    Full-Blue-Racing/FBR24-Electronics

    This repo houses all the code the car needs to run, separated into steering wheel, telemetry, and CAN bus files.

    62 parts

Questions

Is there a KiCad symbol and footprint for the LM2901?

Yes. The symbol is Comparator:LM2901, both drawn on this page. PCBKit places them on a board for you when you design with it.

Which open-source boards use the LM2901?

14 boards in 14 repositories on GitHub; the most starred are listed on this page, with their KiCad files.