Skip to the content
13

LM27762DSS

Texas InstrumentsExtended

-40℃~+85℃ -5V~-1.5V、1.5V~5V 2.5Ω 2.7V~5.5V 250mA 2MHz 390uA Inverted Support WSON-12-EP(2x3) Charge Pumps ROHS

Part id
ti/LM27762DSS
Category
Charge Pumps
Package
WSON-12-EP(2x3)
Pins
13
In stock
41,269 at JLCPCB (C473398)
Used on
43 open-source boards

Overview

The LM27762DSS is a charge Pump made by Texas Instruments in a WSON-12-EP(2x3) package with 13 pins. -40℃~+85℃ -5V~-1.5V、1.5V~5V 2.5Ω 2.7V~5.5V 250mA 2MHz 390uA Inverted Support WSON-12-EP(2x3) Charge Pumps ROHS.

PCBKit's library has its KiCad symbol (Regulator_SwitchedCapacitor:LM27762, from KiCad's library) and its footprint (Package_SON:WSON-12-1EP_3x2mm_P0.5mm_EP1x2.65, from KiCad's library), ready for a KiCad board. 41,269 are in stock at JLCPCB (part C473398). 43 open-source boards in 32 repositories on GitHub use it.

Symbol

1PGOOD2FB+3VIN4GND5CP6OUT-7FB-8EN-9C-10C+11OUT+12EN+13PAD
Regulator_SwitchedCapacitor:LM27762From KiCad's library

Footprint

13
Package_SON:WSON-12-1EP_3x2mm_P0.5mm_EP1x2.65From KiCad's library

From the datasheet

18
Supply, least
2.7 V · VIN, recommended operating min · p. 4
Supply, most
5.5 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
5.8 V · VIN to GND, absolute max · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 4
Works up to
85 °C · Operating ambient temperature max · p. 4
Junction, hottest
150 °C · Junction temperature absolute max · p. 4
Takes working
390 µA · Supply current typical, no load, both enables connected to VIN · p. 5
Takes asleep
500 nA · Shutdown supply current typical · p. 5
Gives
250 mA · Operating output current max, per output · p. 4
Feedback reference
1.22 V · FB– feedback reference typical · p. 5
Feedback reference
1.2 V · FB+ feedback reference typical · p. 5
Dropout
30 mV · Negative LDO typical, IL = 100 mA, VOUT– = −5 V · p. 5
Dropout
45 mV · Positive LDO typical, IL = 100 mA, VOUT = 5 V · p. 5
Switches at
2 MHz · Switching frequency typical, VIN = 3.6 V · p. 5
Junction to air (DSS (WSON))
62.2 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to board (DSS (WSON))
25.6 K/W · Junction-to-board thermal resistance · p. 4
Junction to case (DSS (WSON))
54.7 K/W · Junction-to-case top thermal resistance · p. 4
Junction, hottest
125 °C · maximum operating junction temperature · p. 16

What it is and has

7
Architecture
Inverting charge pump followed by negative LDO · p. 1
Switching
2MHz low-noise fixed-frequency operation · p. 1
Protection
Current limit and thermal protection · p. 1
Power Good
Active-low output · p. 1
Package
DSS (WSON, 12), 3mm × 2mm · p. 1
Switching frequency
2MHz, fixed frequency · p. 1
Inverter output impedance
2.5Ω at VIN = 5V · p. 1

Around it

9
res 10-kΩ
between PGOOD and VIN; Pullup resistor RPU when using the optional open-drain PGOOD feature. · p. 12
res no less than 50 kΩ
between FB+ and GND; R2 in the positive output feedback divider. · p. 13
res no less than 50 kΩ
between FB– and GND; R4 in the negative output feedback divider. · p. 14
cap 2.2 μF
between VIN and GND; CVIN in the application example. · p. 13
cap 4.7-µF
between CP and GND; Low-ESR ceramic charge-pump output capacitor CCP, recommended for typical applications. · p. 15
cap 10-µF, 10-V
between CP and GND; Low-ESR ceramic output capacitor recommended for higher-current applications. · p. 15
cap 4.7-µF
between VIN and GND; Low-ESR ceramic input capacitor recommended for typical applications. · p. 15
cap 0.47-µF or 1-µF 10-V
between C1+ and C1–; Low-ESR ceramic flying capacitor recommended for typical high-current applications; polarized capacitors must not be used. · p. 15
cap 2.2-µF
between OUT+ and GND; Ceramic LDO output capacitor; locate close to the output and return ground to the thermal pad ground connection. · p. 16

Specifications

37
ParameterConditionsAs printedPage
VIN to GND or GND to VOUTOver operating free-air temperature rangemax 5.8 V4
CPOUT, OUT+ and OUT- , continuous output currentmax 300 mA4
OUT+, OUT- short-circuit duration to GNDSee footnote (3)max 1 s4
TJMAX TJMAXSee footnote (4)max 150 °C4
Operating input voltage VINmin 2.7 · max 5.5 V4
Operating output current IOUTmin 0 · max 250 mA4
Operating ambient temperature TAmin -40 · max 85 °C4
Operating junction temperature TJmin -40 · max 125 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; rated value ±1000 Vmax 1000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; rated value ±250 Vmax 250 V4
Junction-to-ambient thermal resistance RθJADSS (WSON), 12 pinstyp 62.2 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DSS (WSON), 12 pinstyp 54.7 °C/W4
Junction-to-board thermal resistance RθJBDSS (WSON), 12 pinstyp 25.6 °C/W4
Junction-to-top characterization parameter ψJTDSS (WSON), 12 pinstyp 1.8 °C/W4
Junction-to-board characterization parameter ψJBDSS (WSON), 12 pinstyp 25.6 °C/W4
Junction-to-case (bottom) thermal resistance RθJC(bot)DSS (WSON), 12 pinstyp 9.2 °C/W5
Supply current IQVIN = 5 V; open circuit, no load, EN+, EN– connected to VIN; TA = 25°Ctyp 390 uA5
Shutdown supply current ISDVIN = 5 V; typical at TA = 25°C, maximum over full temperature rangetyp 0.5 · max 5 uA5
Switching frequency ƒSWVIN = 3.6 Vmin 1.7 · typ 2 · max 2.3 MHz5
Output resistance to CPOUT RNEGVIN = 5.5 V, IL = 100 mAtyp 2.5 Ω5
LDO dropout voltage VLDO–IL = 100 mA, VOUT– = −5 Vtyp 30 mV5
Power supply rejection ratio, OUT– PSRRIL = 100 mA, VOUT– = −1.8 V, 10 kHztyp 50 dB5
Output noise voltage VN–IL = 80 mA, 10 Hz to 100 kHztyp 22 uVRMS5
Feedback pin reference voltage VFB–VIN = 5 Vmin -1.238 · typ -1.22 · max -1.202 V5
Adjustable output voltage VOUT–5.5 V ≥ VIN ≥ 2.7 Vmin -5 · max -1.5 V5
Load regulation VOUT–0 to 250 mA, VOUT = –1.8 Vtyp 34 uV/mA5
Line regulation VOUT–5 V ≥ VIN ≥ 2.7 V, IL = 50 mAtyp 1.5 mV/V5
LDO dropout voltage VLDO+IL = 100 mA, VOUT = 5 Vtyp 45 mV5
Power supply rejection ratio, OUT+ PSRRIL = 100 mA, VOUT+ = 1.8 V, 10 kHztyp 43 dB5
Output noise voltage VN+IL = 80 mA, 10 Hz to 100 kHztyp 22 uVRMS5
Feedback pin reference voltage VFB+VIN = 5 Vmin 1.182 · typ 1.2 · max 1.218 V5
Adjustable output voltage VOUT+5.5 V ≥ VIN ≥ 2.7 Vmin 1.5 · max 5 V5
Load regulation VOUT+0 to 250 mA, VOUT = 1.8 Vtyp 11 uV/mA5
Line regulation VOUT+5 V ≥ VIN ≥ 2.7 V, IL = 50 mAtyp 1.9 mV/V5
Enable pin input voltage high VIH5.5 V ≥ VIN ≥ 2.7 Vmin 1.2 V5
Enable pin input voltage low VIL5.5 V ≥ VIN ≥ 2.7 Vmax 0.4 V5

Pins, by the datasheet

13
1 PGOOD
Power Good flag: logic 0 means power good, logic 1 means power not good; connect to ground if unused. · p. 3
2 FB+
Feedback input; connect to an external resistor divider between OUT+ and GND; do not leave unconnected. · p. 3
3 VIN
Positive power supply input. · p. 3
4 GND
Ground. · p. 3
5 CP
Negative unregulated output voltage. · p. 3
6 OUT–
Regulated negative output voltage. · p. 3
7 FB–
Feedback input; connect to an external resistor divider between OUT– and GND; do not leave unconnected. · p. 3
8 EN–
Active-high enable input for the charge pump and negative LDO. · p. 3
9 C1–
Negative terminal for C1. · p. 3
10 C1+
Positive terminal for C1. · p. 3
11 OUT+
Regulated positive output voltage. · p. 3
12 EN+
Active-high enable input for the positive LDO. · p. 3
— Thermal Pad
Ground; do not leave unconnected. · p. 3

Ordering codes, by the datasheet

6
LM27762DSSR
WSON (DSS), 12 pins · 3000, LARGE T&R; operating temperature -40 to 85°C · p. 22
LM27762DSSR.A
WSON (DSS), 12 pins · 3000, LARGE T&R; operating temperature -40 to 125°C · p. 22
LM27762DSSRG4
WSON (DSS), 12 pins · 3000, LARGE T&R; operating temperature -40 to 125°C · p. 22
LM27762DSSRG4.A
WSON (DSS), 12 pins · 3000, LARGE T&R; operating temperature -40 to 125°C · p. 22
LM27762DSST
WSON (DSS), 12 pins · 250, SMALL T&R; operating temperature -40 to 85°C · p. 22
LM27762DSST.A
WSON (DSS), 12 pins · 250, SMALL T&R; operating temperature -40 to 125°C · p. 22

Open-source boards using it

43See all 43
  • 4 layers101 × 47 mmTdr, the printed circuit board in 3D

    Tdr

    loxodes/tdr

    Prototype time domain reflectometer/sampling oscilloscope

    240 parts58MIT
  • 4 layers80 × 50 mmHarp.device.lickety split, the printed circuit board in 3D

    Harp.device.lickety split

    AllenNeuralDynamics/harp.device.lickety-split

    0360: an ephys-compliant capacitive lick detector

    193 parts5MIT
  • 4 layers80 × 100 mmHarp treadmill, the printed circuit board in 3D

    Harp treadmill

    AllenNeuralDynamics/harp.device.treadmill-driver

    0326: a Harp-compatible device for controlling an instrumented mouse treadmill

    173 parts4
  • 2 layers50.8 × 61 mmNui, the printed circuit board in 3D

    Nui

    alvarop/nui

    Nui is an IR(evntually also BLE) controlled volume controller for analog audio. It sits between your audio source and speakers and can amplify or reduce the volume using IR commands (and evntually BLE).

    53 parts3MIT
  • 6 layers51 × 65 mmOwo, the printed circuit board in 3D

    Owo

    hydrastro/owo

    uwu

    135 parts3
  • 4 layers88.9 × 79.4 mmLink, the printed circuit board in 3D

    Link

    oats-center/avena-rs

    Avena On The Road: Bringing pavement health data to your fingertips

    170 parts3
  • 4 layers77.5 × 152.4 mmPortable line mixer, the printed circuit board in 3D

    Portable line mixer

    sww1235/portable-line-mixer

    A compact line level audio mixer

    138 parts3MIT
  • 2 layers51 × 58.9 mmTach, the printed circuit board in 3D

    Tach

    bistromath/tach

    STM32F103-driven tachometer firmware.

    92 parts2

Questions

Is there a KiCad symbol and footprint for the LM27762DSS?

Yes. The symbol is Regulator_SwitchedCapacitor:LM27762 and the footprint Package_SON:WSON-12-1EP_3x2mm_P0.5mm_EP1x2.65, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LM27762DSS?

WSON-12-EP(2x3), with 13 pins. Its footprint is drawn on this page.

Where is the LM27762DSS datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LM27762DSS?

JLCPCB lists it as part C473398, with 41,269 in stock; the sellers' links on this page open their listings.

Which open-source boards use the LM27762DSS?

43 boards in 32 repositories on GitHub; the most starred are listed on this page, with their KiCad files.