Skip to the content
9

LM27761DSG

Texas InstrumentsExtended

-40℃~+85℃ -5V~-1.5V 2.7V~5.5V 250mA 2MHz 2Ω 370uA 80% Inverted Support WFDFN-8-EP(2x2) Charge Pumps ROHS

Part id
ti/LM27761DSG
Category
Charge Pumps
Package
WFDFN-8-EP(2x2)
Pins
9
In stock
15,808 at JLCPCB (C129351)
Used on
20 open-source boards

Overview

The LM27761DSG is a charge Pump made by Texas Instruments in a WFDFN-8-EP(2x2) package with 9 pins. -40℃~+85℃ -5V~-1.5V 2.7V~5.5V 250mA 2MHz 2Ω 370uA 80% Inverted Support WFDFN-8-EP(2x2) Charge Pumps ROHS.

PCBKit's library has its KiCad symbol (Regulator_SwitchedCapacitor:LM27761, from KiCad's library) and its footprint (Package_SON:Texas_DSG0008A_WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm, from KiCad's library), ready for a KiCad board. 15,808 are in stock at JLCPCB (part C129351). 20 open-source boards in 15 repositories on GitHub use it.

Symbol

1VIN2GND3CPOUT4VOUT5VFB6EN7C-8C+9PAD
Regulator_SwitchedCapacitor:LM27761From KiCad's library

Footprint

9
Package_SON:Texas_DSG0008A_WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mmFrom KiCad's library

From the datasheet

17
Supply, least
2.7 V · VIN, recommended operating minimum · p. 4
Supply, most
5.5 V · VIN, recommended operating maximum · p. 4
Supply, absolute maximum
5.8 V · VIN to GND, absolute maximum · p. 4
Works from
-40 °C · ambient, operating minimum · p. 4
Works up to
85 °C · ambient, operating maximum · p. 4
Junction, hottest
150 °C · junction, absolute maximum · p. 4
Takes working
370 µA · VIN supply current, typical, 5 V, open circuit, no load · p. 5
Takes at most
600 µA · VIN supply current, max, 5 V, open circuit, no load · p. 5
Takes asleep
7 µA · shutdown supply current, typical · p. 5
Gives
250 mA · IOUT, maximum recommended continuous output · p. 4
Current limit
500 mA · input current limit, typical, output shorted to ground · p. 10
Feedback reference
1.22 V · VFB reference voltage, typical · p. 5
Dropout
30 mV · LDO dropout, typical, ILOAD = 100 mA, VOUT = −5 V · p. 5
Switches at
2 MHz · switching frequency, typical, VIN = 3.6 V · p. 5
Junction to air (WSON (DSG))
67.7 K/W · junction-to-ambient thermal resistance · p. 4
Junction to board (WSON (DSG))
37.6 K/W · junction-to-board thermal resistance · p. 4
Junction to case (WSON (DSG))
89.9 K/W · junction-to-case top thermal resistance · p. 4

What it is and has

8
Function
Inverts and regulates the input supply voltage · p. 1
Output ripple
Low · p. 1
Inverter output impedance
2.5Ω, VIN = 5V · p. 1
Regulation
±4% at peak load · p. 1
Protection
Current limit and thermal protection · p. 1
Package
DSG (WSON, 8), 2.00mm × 2.00mm · p. 1
Inverter output impedance
2.5Ω at VIN = 5V · p. 1
LDO PSRR
35dB typical at 2MHz · p. 1

Around it

10
cap 4.7 µF
between VIN and GND; C2 input capacitor in the typical application; ceramic X7R or X5R recommended. · p. 11
cap 1 µF
between C1+ and C1–; C1 flying capacitor in the typical application; ceramic X7R or X5R recommended. · p. 11
cap 4.7 µF
between CPOUT and GND; C3 charge-pump output capacitor in the typical application; ceramic X7R or X5R recommended. · p. 11
cap 2.2 µF
between VOUT and GND; C4 LDO output capacitor in the typical application; ceramic X7R or X5R recommended. · p. 11
res no less than 50 kΩ
between VFB and GND; R2 in the output voltage setting divider. · p. 13
cap 4.7 µF
between VCPOUT and GND; C3: low-ESR ceramic charge-pump output capacitor for typical applications. · p. 14
cap 10 µF
between VCPOUT and GND; 10-V low-ESR ceramic charge-pump output capacitor for higher-current applications; account for DC bias derating. · p. 14
cap 4.7 µF
between VIN and GND; C2: low-ESR ceramic input capacitor; place close to the device with short, wide connections. · p. 14
cap 0.47 µF or 1 µF
between C1+ and C1–; C1: 10-V low-ESR ceramic flying capacitor for typical high-current applications. Do not use polarized capacitors. · p. 14
cap 2.2 µF
between VOUT and GND; C4: ceramic LDO output capacitor for stability; place close to the output. · p. 14

Specifications

31
ParameterConditionsAs printedPage
Ground voltage, VIN to GND or GND to VOUTOver operating free-air temperature rangemax 5.8 V4
Continuous output current, CPOUT and VOUTOver operating free-air temperature rangemax 300 mA4
TJMAX (3) TJMAXmax 150 °C4
Storage temperature, Tstg Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; rating ±1000 Vmax 1000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; rating ±250 Vmax 250 V4
Operating ambient temperature, TA TAmin -40 · max 85 °C4
Operating junction temperature, TJ TJmin -40 · max 125 °C4
Operating input voltage, VIN VINOver operating free-air temperature rangemin 2.7 · max 5.5 V4
Operating output current, IOUT IOUTOver operating free-air temperature rangemin 0 · max 250 mA4
Junction-to-ambient thermal resistance RθJALM27761, WSON (DSG), 8 PINStyp 67.7 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)LM27761, WSON (DSG), 8 PINStyp 89.9 °C/W4
Junction-to-board thermal resistance RθJBLM27761, WSON (DSG), 8 PINStyp 37.6 °C/W4
Junction-to-top characterization parameter ψJTLM27761, WSON (DSG), 8 PINStyp 2.4 °C/W4
Junction-to-board characterization parameter ψJBLM27761, WSON (DSG), 8 PINStyp 38 °C/W4
Junction-to-case (bottom) thermal resistance RθJC(bot)LM27761, WSON (DSG), 8 PINStyp 9.4 °C/W4
Supply current IqVIN = 5 V; open circuit, no load; typical at TA = 25°C, limits over full temperature range; C1 to C4 as in Typical Applicationtyp 370 · max 600 uA5
Shutdown supply current ISDVIN = 5 V; typical at TA = 25°C, limits over full temperature range; C1 to C4 as in Typical Applicationtyp 7 · max 12 uA5
Switching frequency ƒSWVIN = 3.6 V; typical at TA = 25°C, limits over full temperature range; C1 to C4 as in Typical Applicationmin 1.7 · typ 2 · max 2.3 MHz5
Output resistance to CPOUT RNEGVIN = 5.5 V; TA = 25°C; C1 to C4 as in Typical Applicationtyp 2 Ω5
LDO dropout voltage VDOILOAD = 100 mA, VOUT = −5 V; VIN = 5 V; TA = 25°C; C1 to C4 as in Typical Applicationtyp 30 mV5
Power supply rejection ratio PSRRILOAD = 80 mA, VCPOUT = −5 V; VIN = 5 V; TA = 25°C; C1 to C4 as in Typical Applicationtyp 35 dB5
Output noise voltage VNILOAD = 80 mA, 10 Hz to 100 kHz; VIN = 5 V; TA = 25°C; C1 to C4 as in Typical Applicationtyp 20 uVRMS5
Feedback pin reference voltage VFBVIN = 5 V; typical at TA = 25°C, limits over full temperature range; C1 to C4 as in Typical Applicationmin 1.202 · typ 1.22 · max 1.238 V5
Adjustable output voltage VOUT5.5 V ≥ VIN ≥ 2.7 V; full temperature range; C1 to C4 as in Typical Applicationmin -5 · max -1.5 V5
Load regulation0 to 250 mA, VOUT = −1.8 V; VIN = 5 V; TA = 25°C; C1 to C4 as in Typical Applicationtyp 4.6 uV/mA5
Line regulation5.5 V ≥ VIN ≥ 2.7 V, ILOAD = 50 mA; TA = 25°C; C1 to C4 as in Typical Applicationtyp 1.5 mV/V5
Enable pin input voltage high VIH5.5 V ≥ VIN ≥ 2.7 V; full temperature rangemin 1.2 V5
Enable pin input voltage low VIL5.5 V ≥ VIN ≥ 2.7 V; full temperature rangemax 0.4 V5
Undervoltage lockout UVLOVIN falling; TA = 25°Ctyp 2.6 V5
Undervoltage lockout UVLOVIN rising; TA = 25°Ctyp 2.4 V5

Pins, by the datasheet

9
1 VIN
Positive power supply input. · p. 3
2 GND
Ground. · p. 3
3 CPOUT
Negative unregulated output voltage. · p. 3
4 VOUT
Regulated negative output voltage. · p. 3
5 VFB
Feedback input; connect to an external resistor divider between VOUT and GND; do not leave unconnected. · p. 3
6 EN
Active high enable input. · p. 3
7 C1–
Negative terminal for C1. · p. 3
8 C1+
Positive terminal for C1. · p. 3
— Thermal Pad
Ground; do not leave unconnected. · p. 3

Ordering codes, by the datasheet

6
LM27761DSGR
WSON (DSG) | 8 · 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 19
LM27761DSGR.A
WSON (DSG) | 8 · 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 19
LM27761DSGRG4
WSON (DSG) | 8 · 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 19
LM27761DSGRG4.A
WSON (DSG) | 8 · 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 19
LM27761DSGT
WSON (DSG) | 8 · 250 units, SMALL T&R; operating temperature -40 to 85 °C · p. 19
LM27761DSGT.A
WSON (DSG) | 8 · 250 units, SMALL T&R; operating temperature -40 to 85 °C · p. 19

Open-source boards using it

20See all 20
  • 6 layers122.5 × 103.5 mmThunderscope Rev5.3, the printed circuit board in 3D

    Thunderscope Rev5.3

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    1,022 parts1.3kMIT
  • 4 layers70 × 72 mmSPINC AA Charger, the printed circuit board in 3D

    SPINC AA Charger

    CoretechR/SPINC

    DIY Automatic Battery Charger Using RP2040

    101 parts467GPL-3.0
  • 4 layers129.5 × 52.3 mmPn wing prototype, the printed circuit board in 3D

    Pn wing prototype

    loxodes/phasenoise

    Prototype phase noise analyzer

    277 parts23MIT
  • 8 layers124 × 190 mmFreesample, the printed circuit board in 3D

    Freesample

    azonenberg/freesample

    High performance sampling oscilloscope based on INTEGRALSTICK

    577 parts10BSD-3-Clause
  • 4 layers60 × 40 mmFtx, the printed circuit board in 3D

    Ftx

    SETIatHCRO/Front-Page

    Documentation related to the Allen Telescope Array at the Hat Creek Radio Observatory Wiki Link Below

    153 parts5
  • 4 layers85.6 × 54 mmJammer Front End, the printed circuit board in 3D

    Jammer Front End

    adrianiaz/Jammer_Front_End

    Design of a switched and tunable RF preselector that selects bands within 2-18 GHz for direct-sampling receiver applications..

    116 parts1
  • 2 layers40.4 × 20.8 mmME3-H2, the printed circuit board in 3D

    ME3-H2

    uf-mil-electrical/misc_hardware

    PCB stuff that doesn't belong to any specific robot

    25 parts1
  • 4 layers100 × 60 mmSimple just sensor, the printed circuit board in 3D

    Simple just sensor

    williamlin108/USAYPT2026_FlashSensor_MLWGS

    10kHz cutoff bandwidth; TO-5 Package Si-photodiode with TIA amplifier (G:2k)

    78 parts1

Questions

Is there a KiCad symbol and footprint for the LM27761DSG?

Yes. The symbol is Regulator_SwitchedCapacitor:LM27761 and the footprint Package_SON:Texas_DSG0008A_WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LM27761DSG?

WFDFN-8-EP(2x2), with 9 pins. Its footprint is drawn on this page.

Where is the LM27761DSG datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LM27761DSG?

JLCPCB lists it as part C129351, with 15,808 in stock; the sellers' links on this page open their listings.

Which open-source boards use the LM27761DSG?

20 boards in 15 repositories on GitHub; the most starred are listed on this page, with their KiCad files.