Skip to the content
31

HD3SS3220RNHR

Texas InstrumentsExtended

0℃~+70℃ 4.5V~5.5V 5uA I2C Not supported Not supported WQFN-30-EP(2.5x4.5) Analog Switches, Multiplexers ROHS

Part id
ti/HD3SS3220RNHR
Category
Battery Management
Package
WQFN-30-EP(2.5x4.5)
Pins
31
In stock
1,634 at JLCPCB (C165155)
Used on
7 open-source boards

Overview

The HD3SS3220RNHR is a battery Management made by Texas Instruments in a WQFN-30-EP(2.5x4.5) package with 31 pins. 0℃~+70℃ 4.5V~5.5V 5uA I2C Not supported Not supported WQFN-30-EP(2.5x4.5) Analog Switches, Multiplexers ROHS.

PCBKit's library has its KiCad symbol (HD3SS3220RNH:HD3SS3220RNH, from Antmicro) and its footprint (EasyEDA_Cloud:QFN-30_L4.5-W2.5-P0.40-BL-EP, from EasyEDA), ready for a KiCad board. 1,634 are in stock at JLCPCB (part C165155). 7 open-source boards in 6 repositories on GitHub use it.

Symbol

1CC22CC13CURRENT_MODE4PORT5VBUS_DET6TX+7TX-8VCC339RX+10RX-11DIR12ENn_MUX13GND14RX1-15RX1+16TX1-17TX1+18RX2-19RX2+20TX2-21TX2+22ADDR23INT_N/OUT324VCONN_FAULT_N25SDA/OUT126SCL/OUT227ID29ENn_CC30VDD5
HD3SS3220RNH:HD3SS3220RNHFrom Antmicro

Footprint

31
EasyEDA_Cloud:QFN-30_L4.5-W2.5-P0.40-BL-EPFrom EasyEDA

From the datasheet

17
Supply, least
4.5 V · VDD5, recommended operating min · p. 5
Supply, most
5.5 V · VDD5, recommended operating max · p. 5
Supply, least
3 V · VCC33, recommended operating min · p. 5
Supply, most
3.6 V · VCC33, recommended operating max · p. 5
Supply, least
1.65 V · VDD, I2C supply recommended operating min · p. 5
Supply, absolute maximum
6 V · VDD5, absolute max · p. 5
Supply, absolute maximum
4 V · VCC33, absolute max · p. 5
Works from
0 °C · HD3SS3220 operating ambient min · p. 5
Works up to
70 °C · HD3SS3220 operating ambient max · p. 5
Takes working
700 µA · typical active current, CC controller and SS mux on · p. 6
Takes at most
900 µA · max active current, CC controller and SS mux on · p. 6
Takes asleep
5 µA · typical shutdown current, ENn_CC/Mux = H · p. 6
Current limit
300 mA · typical VCONN current limit · p. 7
Junction to air (RNH (VQFN))
60.9 K/W · junction-to-ambient thermal resistance · p. 6
Junction to case (RNH (VQFN))
50.4 K/W · junction-to-case top thermal resistance · p. 6
Junction to board (RNH (VQFN))
22.8 K/W · junction-to-board thermal resistance · p. 6
Data rate, most
10 Gbit/s · USB 3.1 G1 and G2 max data rate · p. 1

What it is and has

10
USB data rate
USB 3.1 G1 and G2, up to 10Gbps · p. 1
Port controller and mux
USB Type-C DRP port controller with SuperSpeed 2:1 MUX · p. 1
Host mode
DFP/Source · p. 1
Device mode
UFP/Sink · p. 1
Dual role mode
DRP · p. 1
DRP preferences
Try.SRC and Try.SNK · p. 1
Configuration control
GPIO and I2C · p. 1
Cable orientation detection
Supported · p. 1
Role detection
Supported · p. 1
Type-C current mode
Default, Mid, High · p. 1

Around it

4
res 900K
between VBUS and VBUS_DET; Required external series resistor between system VBUS and VBUS_DET. · p. 3
res 500K
between CURRENT_MODE and VDD5; Selects 1.5A current advertisement. · p. 3
res 10K
between CURRENT_MODE and VDD5; Selects 3A current advertisement. · p. 3
res 4.7 KΩ
between PORT and VDD5; Nominal external tri-level input pull-up; high selects DFP mode. · p. 5

Specifications

73
ParameterConditionsAs printedPage
5V Supply Voltage VDD5Over operating free-air temperature rangemin -0.3 · max 6 V5
3.3V Supply Voltage VCC33Over operating free-air temperature rangemin -0.3 · max 4 V5
Control PinsADDR, PORT, ID, INT_N/OUT3, ENn_CC, SDA/OUT1, SCL/OUT2; maximum VDD5 +0.3 Vmin -0.3 V5
Control PinsCC1, CC2min -0.3 · max 6 V5
Control PinsENn_MUX, DIR; maximum VCC33 +0.3 Vmin -0.3 V5
Control PinsVBUS_DETmin -0.3 · max 4 V5
Super-speed Differential Signal Pins[RX/TX] [p/n], [RX/TX][2/1][p/n]min -0.3 · max 2.5 V5
Storage temperature Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V5
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1500 Vmax 1500 V5
5V Supply Voltage range VDD5With 200mA VCONN current for VCONN ≥ 4.75V at connector, VDD5 ≥ 5V is recommendedmin 4.5 · max 5.5 V5
3.3V Supply Voltage range VCC33min 3 · max 3.6 V5
Supply range for I2C (SDA, SCL) pins VDDmin 1.65 · max 3.6 V5
VDD5 supply ramp time VDD5(ramp)max 25 ms5
High speed signal pins differential voltage V(diff)min 0 · max 1.8 VPP5
High speed signal pins common mode voltage V(cm)min 0 · max 2 V5
Operating free-air/ambient temperature (HD3SS3220) TAHD3SS3220min 0 · max 70 °C5
System V(BUS) input voltage through 900K resistor V(BUS)min 4 · typ 5 · max 28 V5
Bulk capacitance on VCONN. Only when VCONN is on. C(BULK)Disconnected when VCONN is off. Shall be placed on VDD5.min 10 · max 200 uF5
External Pull up resistor on Open Drain IOs (OUT1, OUT2, INT/OUT3, ID, VCONN_FAULT_N, and DIR pins) R(p_ODext)typ 200 KΩ5
Tri-level input external pull-up resistor (PORT and ADDR pins) R(p_TLext)typ 4.7 KΩ5
External pull up resistor to advertise 1.5A (CURRENT_MODE pin) R(p_15A)typ 500 KΩ5
External pull up resistor to advertise 3A (CURRENT_MODE pin) R(p_3A)typ 10 KΩ5
External Pull up resistance on I2C bus R(p_i2c_ext)Could be 4.7K or higher. Nominal value listedtyp 2.2 KΩ5
External resistor on VBUS_DET pin R(VBUS)min 880 · typ 900 · max 910 KΩ6
Junction-to-ambient thermal resistance RθJAHD3SS3220, RNH (VQFN), 30 PINStyp 60.9 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)HD3SS3220, RNH (VQFN), 30 PINStyp 50.4 °C/W6
Junction-to-board thermal resistance RθJBHD3SS3220, RNH (VQFN), 30 PINStyp 22.8 °C/W6
Junction-to-top characterization parameter ψJTHD3SS3220, RNH (VQFN), 30 PINStyp 1.7 °C/W6
Junction-to-board characterization parameter ψJBHD3SS3220, RNH (VQFN), 30 PINStyp 22.6 °C/W6
Junction-to-case (bottom) thermal resistance RθJC(bot)HD3SS3220, RNH (VQFN), 30 PINStyp 12.1 °C/W6
Current consumption in active mode- both CC controller and SS mux on I(ACTIVE)ENn_CC/Mux = Ltyp 0.7 · max 0.9 mA6
Current consumption in active mode – CC controller on and SS mux off ICCENn_CC = L, ENn_Mux = Htyp 0.2 mA6
Current consumption in shutdown mode I(SHUTDOWN)ENn_CC/Mux = Htyp 5 uA6
Pulldown resistor when in dead-battery mode. R(CC_DB)min 4.1 · typ 5.1 · max 6.1 kΩ6
Pulldown resistor when in UFP or DRP mode. R(CC_D)min 4.6 · typ 5.1 · max 5.6 kΩ6
Voltage level for detecting a DFP attach when configured as a UFP and DFP is advertising default current source capability. V(UFP_CC_USB)min 0.25 · max 0.61 V6
Voltage level for detecting a DFP attach when configured as a UFP and DFP is advertising medium (1.5A) current source capability. V(UFP_CC_MED)min 0.7 · max 1.16 V6
Voltage level for detecting a DFP attach when configured as a UFP and DFP is advertising high (3A) current source capability. V(UFP_CC_HIGH)min 1.31 · max 2.04 V6
Voltage level for detecting a UFP attach when configured as a DFP and advertising default current source capability. V(DFP_CC_USB)min 1.51 · typ 1.6 · max 1.64 V6
Voltage level for detecting a UFP attach when configured as a DFP and advertising 1.5A current source capability. V(DFP_CC_MED)min 1.51 · typ 1.6 · max 1.64 V6
Voltage level for detecting a UFP attach when configured as a DFP and advertising 3A current source capability. V(DFP_CC_HIGH)min 2.46 · typ 2.6 · max 2.74 V6
Voltage level for detecting an active cable attach when configured as a DFP and advertising default current source capability. V(AC_CC_USB)min 0.15 · typ 0.2 · max 0.25 V6
Voltage level for detecting an active cable attach when configured as a DFP and advertising 1.5A current source capability. V(AC_CC_MED)min 0.35 · typ 0.4 · max 0.45 V6
Voltage level for detecting an active cable attach when configured as a DFP and advertising 3A current source capability. V(DFP_CC_HIGH)min 0.75 · typ 0.8 · max 0.84 V7
Default mode pull-up current source when operating in DFP or DRP mode. ICC(DEFAULT_P)min 64 · typ 80 · max 96 uA7
Medium (1.5A) mode pull-up current source when operating in DFP or DRP mode. ICC(MED_P)min 166 · typ 180 · max 194 uA7
High (3A) mode pull-up current source when operating in DFP or DRP mode. ICC(HIGH_P)min 34 · typ 330 · max 356 uA7
Low-level input voltage VIL3-Level Input Pins: PORT, ADDR, ENn_CC and CURRENT_MODEmax 0.4 V7
High-level input current IIH3-Level Input Pins: PORT, ADDR, ENn_CC and CURRENT_MODEmin 20 · max 20 uA7
Low-level input current IIL3-Level Input Pins: PORT, ADDR, ENn_CC and CURRENT_MODEmin -10 · max 10 uA7
Current Leakage on ID pin IID(LKG)VDD5 = 0V, ID = 5Vmax 10 uA7
Internal pull-up resistance (PORT and ADDR pins) R(pu)typ 588 kΩ7
Internal pull-down resistance (PORT and ADDR pins) R(pd)typ 1.1 MΩ7
Internal pull-down resistance (CURRENT_MODE pin) R(pd_CURRENT)typ 275 kΩ7
Internal pull-up resistance (ENn_CC pin) R(ENn_CC)typ 1.1 MΩ7
High-level input current IIHENn_MUXmin -1 · max 1 uA7
Low-level input current IILENn_MUXmin -1 · max 1 uA7
Low-level signal output voltage VOLOpen Drain Output Pins: OUT1, OUT2, INT_N/OUT3, ID, VCONN_FAULT_N, DIR; IOL = –1.6mAmax 0.4 V7
High-level input voltage VIHI2C– SDA/OUT1, SCL/OUT2 can Operate from 1.8/3.3V (±10%)min 1.05 V7
Low-level input voltage VILI2C– SDA/OUT1, SCL/OUT2 can Operate from 1.8/3.3V (±10%)max 0.4 V7
Low-level output voltage (open-drain) VOLI2C; IOL = –1.6mAmax 0.4 V7
VBUS threshold range V(BUS_THR)VBUS_DET IO Pin (Connected to System VBUS Signal)min 2.95 · typ 3.3 · max 3.8 V7
External resistor between VBUS and VBUS_DET pin RVBUSmin 855 · typ 887 · max 920 KΩ7
Internal pull-down resistor at VBUS_DET pin R(VBUS_DET_INT)typ 95 kΩ7
On resistance of the VCONN power FET RONVCONNmax 1.25 Ω7
Voltage tolerance on VCONN power FET V(TOL)max 5.5 V7
Voltage to pass through VCONN power FET V(pass)max 5.5 V7
VCONN current limit. VCONN will be disconnected above this value I(VCONN)min 225 · typ 300 · max 375 mA7
Differential Insertion Loss ILf = 0.3Mhztyp -0.43 dB7
Differential Insertion Loss ILf = 2.5Ghztyp -1.07 dB7
Differential Insertion Loss ILf = 5Ghztyp -1.42 dB7
Bandwidth BWMUX High Speed Performance Parameterstyp 8 Ghz7

Pins, by the datasheet

17
1 CC2
Type-C Configuration channel signal 2. · p. 3
2 CC1
Type-C Configuration channel signal 1. · p. 3
3 CURRENT_MODE
Tri-level current advertisement input in DFP or DRP source operation in GPIO mode; low selects 900mA, 500K to VDD5 selects 1.5A, and 10K to VDD5 selects 3A. · p. 3
4 PORT
Tri-level port mode input sampled when ENn_CC is asserted low with VDD5 active and following I2C_SOFT_RESET; high selects DFP, unconnected selects DRP, and low selects UFP. · p. 3
5 VBUS_DET
VBUS detection input for UFP attachment; connect to system VBUS through a 900K external resistor. · p. 3
6 TXp
Host/Device USB SuperSpeed differential Signal TX positive. · p. 3
7 TXn
Host/Device USB SuperSpeed differential Signal TX negative. · p. 3
8 VCC33
3.3-V Power supply. · p. 3
9 RXp
Host/Device USB SuperSpeed differential Signal RX positive. · p. 3
10 RXn
Host/Device USB SuperSpeed differential Signal RX negative. · p. 3
11 DIR
Type-C plug orientation output; a pull-up resistor such as 200K is required. · p. 3
12 ENn_MUX
Active low MUX enable; low enables normal operation and high selects shutdown. · p. 3
13 GND
Ground. · p. 3
14 RX1n
Type-C Port - USB SuperSpeed differential Signal RX1 negative. · p. 3
15 RX1p
Type-C Port - USB SuperSpeed differential Signal RX1 positive. · p. 3
16 TX1n
Type-C Port - USB SuperSpeed differential Signal TX1 negative. · p. 3
28 GND
Ground. · p. 3

Open-source boards using it

7
  • 8 layers106 × 62 mmCm5-m2key b usb3-ix, the printed circuit board in 3D

    Cm5-m2key b usb3-ix

    taskx6004/AnyRadio-CM5

    modular RPI CM5 carrier board

    224 parts42
  • 4 layers26 × 98 mmDongle pro, the printed circuit board in 3D

    Dongle pro

    fcjr/restorekit

    Reformat an Apple Silicon mac from any platform.

    111 parts34Apache-2.0
  • 6 layers45 × 0 mmBase board, the printed circuit board in 3D

    Base board

    GeniePod/genie-hardware

    GeniePod Home V1 hardware: MVP testing build, wiring, BOM, and planned interface-board/enclosure docs.

    222 parts2CERN-OHL-S-2.0
  • 6 layers92.6 × 69.4 mmUsb hub 2, the printed circuit board in 3D

    Usb hub 2

    yedidia-sisay/usb3-multiport-hub

    An open-source USB 3.2 Gen 2 (10 Gbps) multiport hub & docking station.

    230 parts
  • 4 layers190 × 110 mmWith GL3224, the printed circuit board in 3D

    With GL3224

    Benjamin-girard-1/magnetometer-node-old

    282 parts
  • 6 layers75.1 × 102 mmCm5, the printed circuit board in 3D

    Cm5

    hydazz/iasis

    An optional Raspberry Pi Compute Module 5 carrier for Iasis. It plugs into the main board's HubPD population and carries Ethernet, NVMe storage, an accessory USB-C port and a service USB-C port.

    84 partsApache-2.0

Questions

Is there a KiCad symbol and footprint for the HD3SS3220RNHR?

Yes. The symbol is HD3SS3220RNH:HD3SS3220RNH and the footprint EasyEDA_Cloud:QFN-30_L4.5-W2.5-P0.40-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the HD3SS3220RNHR?

WQFN-30-EP(2.5x4.5), with 31 pins. Its footprint is drawn on this page.

Where is the HD3SS3220RNHR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the HD3SS3220RNHR?

JLCPCB lists it as part C165155, with 1,634 in stock; the sellers' links on this page open their listings.

Which open-source boards use the HD3SS3220RNHR?

7 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.