Skip to the content
123456789101112131415161717171717

DRV8874PWP

Texas InstrumentsExtended

-40℃~+125℃ 1 200mΩ 750nA 9A Yes HTSSOP-16-EP Brushed DC Motor Drivers ROHS

Part id
ti/DRV8874PWP
Category
Brushed DC Motor Drivers
Package
HTSSOP-16-EP
Pins
16
In stock
12,551 at JLCPCB (C1855818)
Used on
13 open-source boards

Overview

The DRV8874PWP is a brushed DC Motor Driver made by Texas Instruments in a HTSSOP-16-EP package with 17 pins. -40℃~+125℃ 1 200mΩ 750nA 9A Yes HTSSOP-16-EP Brushed DC Motor Drivers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:DRV8874QPWPRQ1, from EasyEDA) and its footprint (EasyEDA_Cloud:HTSSOP-16_L5.0-W4.4-P0.65-LS6.4-BL-EP, from EasyEDA), ready for a KiCad board. 12,551 are in stock at JLCPCB (part C1855818). 13 open-source boards in 11 repositories on GitHub use it.

Symbol

17EP16PMODE15GND14CPL13CPH12VCP11VM10OUT29PGND8OUT17IMODE6IPROPI5VREF4nFAULT3nSLEEP2PH/IN21EN/IN1
EasyEDA_Cloud:DRV8874QPWPRQ1From EasyEDA

Footprint

123456789101112131415161717171717
EasyEDA_Cloud:HTSSOP-16_L5.0-W4.4-P0.65-LS6.4-BL-EPFrom EasyEDA

From the datasheet

12
Supply, least
4.5 V · VM, recommended operating min · p. 4
Supply, most
37 V · VM, recommended operating max · p. 4
Supply, absolute maximum
40 V · VM, absolute max · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 4
Works up to
125 °C · Operating ambient temperature max · p. 4
Junction, hottest
150 °C · Operating junction temperature max · p. 4
Takes working
3 mA · VM active mode typical, VVM = 24 V, nSLEEP = 5 V, EN/IN1 = PH/IN2 = 0 V · p. 5
Takes asleep
750 nA · VM sleep mode typical, VVM = 24 V, nSLEEP = 0 V, TJ = 25°C · p. 5
Junction to air (PWP (HTSSOP))
36 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to board (PWP (HTSSOP))
11.1 K/W · Junction-to-board thermal resistance · p. 5
Junction to case (PWP (HTSSOP))
27.3 K/W · Junction-to-case (top) thermal resistance · p. 5
Edge
150 ns · Output rise time typical, VVM = 24 V, OUTx rising 10% to 90% · p. 6

What it is and has

14
Driver
N-channel H-bridge motor driver · p. 1
Bidirectional motor support
One brushed DC motor · p. 1
Unidirectional motor support
Two brushed DC motors · p. 1
H-bridge on resistance
200 mΩ, high-side + low-side · p. 1
Peak output current
6 A · p. 1
Current sensing
Integrated current sensing and regulation · p. 1
Current regulation modes
Cycle-by-cycle or fixed off time · p. 1
H-bridge control modes
PH/EN and PWM · p. 1
Half-bridge control
Independent half-bridge control mode · p. 1
Logic input compatibility
1.8 V, 3.3 V, 5 V · p. 1
Protection
Undervoltage lockout · p. 1
Protection
Overcurrent protection · p. 1
Protection
Thermal shutdown · p. 1
Package
PWP, 16-pin HTSSOP with exposed thermal pad · p. 3

Around it

8
cap 0.1-µF
between VM and GND; CVM1; low ESR ceramic capacitor, VM-rated. · p. 10
cap Bulk Capacitance
between VM and GND; CVM2; VM-rated. · p. 10
cap 100-nF
between VCP and VM; CVCP; X5R or X7R, 16-V ceramic capacitor. · p. 10
cap 22-nF
between CPH and CPL; CFLY; X5R or X7R, VM-rated ceramic capacitor. · p. 10
res Pullup resistor
between VCC and nFAULT; RnFAULT; choose resistance to keep IOD ≤ 5 mA. · p. 10
res 20 kΩ
between IMODE and GND; Quad-level 2: cycle-by-cycle current chopping, automatic retry overcurrent response. · p. 13
res 62 kΩ
between IMODE and GND; Quad-level 3: cycle-by-cycle current chopping, outputs latched off after overcurrent. · p. 13
res 1500 Ω
between IPROPI and GND; Current regulation example with VVREF = 2.5 V and AIPROPI = 455 uA/A; stated ITRIP approximately 3.66 A. · p. 13

Specifications

87
ParameterConditionsAs printedPage
Power supply pin voltageVMmin -0.3 · max 40 V4
Voltage difference between ground pinsGND, PGNDmin -0.3 · max 0.3 V4
Charge pump low-side pin voltageCPL; maximum VVM + 0.3 Vmin -0.3 V4
Logic pin voltageEN/IN1, IMODE, nSLEEP, PH/IN2, PMODEmin -0.3 · max 5.75 V4
Open-drain output pin voltagenFAULTmin -0.3 · max 5.75 V4
Output pin voltageOUT1, OUT2; maximum VVM + 0.9 Vmin -0.9 V4
Proportional current output pin voltageIPROPImin -0.3 · max 5.75 V4
Proportional current output pin voltageIPROPI; maximum VVM + 0.3 Vmin -0.3 V4
Reference input pin voltageVREFmin -0.3 · max 5.75 V4
Ambient temperature, TAmin -40 · max 125 °C4
Junction temperature, TJmin -40 · max 150 °C4
Storage temperature, Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; value ±2000 Vmin -2000 · max 2000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101; value ±500 Vmin -500 · max 500 V4
Power supply voltage VVMVMmin 4.5 · max 37 V4
Logic input voltage VINEN/IN1, MODE, nSLEEP, PH/IN2min 0 · max 5.5 V4
PWM frequency fPWMEN/IN1, PH/IN2min 0 · max 100 kHz4
Open drain pullup voltage VODnFAULTmin 0 · max 5.5 V4
Open drain output current IODnFAULTmin 0 · max 5 mA4
Peak output current IOUTOUT1, OUT2; power dissipation and thermal limits must be observedmin 0 · max 6 A4
Current sense output current IIPROPIIPROPImin 0 · max 3 mA4
Current limit reference voltage VVREFVREFmin 0 · max 3.6 V4
Operating ambient temperature TAmin -40 · max 125 °C4
Operating junction temperature TJmin -40 · max 150 °C4
Junction-to-ambient thermal resistance RθJADRV8874, PWP (HTSSOP), 16 PINStyp 36 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DRV8874, PWP (HTSSOP), 16 PINStyp 27.3 °C/W5
Junction-to-board thermal resistance RθJBDRV8874, PWP (HTSSOP), 16 PINStyp 11.1 °C/W5
Junction-to-top characterization parameter ΨJTDRV8874, PWP (HTSSOP), 16 PINStyp 0.4 °C/W5
Junction-to-board characterization parameter ΨJBDRV8874, PWP (HTSSOP), 16 PINStyp 11 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)DRV8874, PWP (HTSSOP), 16 PINStyp 2.7 °C/W5
VM sleep mode current IVMQVVM = 24 V, nSLEEP = 0 V, TJ = 25°Ctyp 0.75 · max 1 uA5
VM sleep mode current IVMQnSLEEP = 0 Vmax 5 uA5
VM active mode current IVMVVM = 24 V, nSLEEP = 5 V, EN/IN1 = PH/IN2 = 0 Vtyp 3 · max 7 mA5
Turnon time tWAKEVVM > VUVLO, nSLEEP = 5 V to activemax 1 ms5
Turnoff time tSLEEPnSLEEP = 0 V to sleep modemax 1 ms5
Charge pump regulator voltage VVCPVCP with respect to VM, VVM = 24 Vtyp 5 V5
Charge pump switching frequency fVCPtyp 400 kHz5
Input logic low voltage VILEN/IN1, PH/IN2, nSLEEP; VVM < 5 Vmin 0 · max 0.7 V5
Input logic low voltage VILEN/IN1, PH/IN2, nSLEEP; VVM ≥ 5 Vmin 0 · max 0.8 V5
Input logic high voltage VIHEN/IN1, PH/IN2, nSLEEPmin 1.5 · max 5.5 V5
Input hysteresis VHYSEN/IN1, PH/IN2typ 200 mV5
Input hysteresis VHYSnSLEEPtyp 50 mV5
Input logic low current IILEN/IN1, PH/IN2, nSLEEP; VI = 0 Vmin -5 · max 5 uA5
Input logic high current IIHEN/IN1, PH/IN2, nSLEEP; VI = 5 Vtyp 50 · max 75 uA5
Input pulldown resistance RPDEN/IN1, PH/IN2, nSLEEP; To GNDtyp 100 kΩ5
Tri-level input logic low voltage VTILPMODEmin 0 · max 0.65 V5
Tri-level input Hi-Z voltage VTIZPMODEmin 0.9 · typ 1.1 · max 1.2 V5
Tri-level input logic high voltage VTIHPMODEmin 1.5 · max 5.5 V5
Tri-level input logic low current ITILPMODE; VI = 0 Vmin -50 · typ -32 uA5
Tri-level input Hi-Z current ITIZPMODE; VI = 1.1 Vmin -10 · max 10 uA5
Tri-level input logic high current ITIHPMODE; VI = 5 Vtyp 113 · max 150 uA5
Tri-level pulldown resistance RTPDPMODE; To GNDtyp 44 kΩ5
Tri-level pullup resistance RTPUPMODE; To internal 5 Vtyp 156 kΩ5
Quad-level input level 1 VQI2IMODE; Voltage to set quad-level 1min 0 · max 0.45 V5
Quad-level input level 2 RQI2IMODE; Resistance to GND to set quad-level 2min 18.6 · typ 20 · max 21.4 kΩ5
Quad-level input level 3 RQI3IMODE; Resistance to GND to set quad-level 3min 57.6 · typ 62 · max 66.4 kΩ5
Quad-level input level 4 VQI4IMODE; Voltage to set quad-level 4min 2.5 · max 5.5 V5
Quad-level pulldown resistance RQPDIMODE; To GNDtyp 136 kΩ5
Quad-level pullup resistance RQPUIMODE; To internal 5 Vtyp 68 kΩ5
Output logic low voltage VOLnFAULT; IOD = 5 mAmax 0.3 V6
Output logic high current IOZnFAULT; VOD = 5 Vmin -2 · max 2 uA6
High-side MOSFET on resistance RDS(on)_HSVVM = 24 V, IO = 2 A, TJ = 25°Ctyp 100 · max 120 mΩ6
Low-side MOSFET on resistance RDS(on)_LSVVM = 24 V, IO = –2 A, TJ = 25°Ctyp 100 · max 120 mΩ6
Body diode forward voltage VSDISD = 1 Atyp 0.9 V6
Output rise time tRISEVVM = 24 V, OUTx rising 10% to 90%typ 150 ns6
Output fall time tFALLVVM = 24 V, OUTx falling 90% to 10%typ 150 ns6
Input to output propagation delay tPDEN/IN1, PH/IN2 to OUTx, 200 Ω from OUTx to GNDtyp 400 ns6
Output dead time tDEADBody diode conductingtyp 100 ns6
Current mirror scaling factor AIPROPItyp 450 uA/A6
Current mirror scaling error AERRIOUT < 0.4 A; 5.5 V ≤ VVM ≤ 37 Vmin -30 · max 30 mA6
Current mirror scaling error AERR0.4 A ≤ IOUT < 1 A; 5.5 V ≤ VVM ≤ 37 Vmin -7.5 · max 7.5 %6
Current mirror scaling error AERR1 A ≤ IOUT < 2 A; 5.5 V ≤ VVM ≤ 37 Vmin -6 · max 6 %6
Current mirror scaling error AERR2 A ≤ IOUT ≤ 4 A; 5.5 V ≤ VVM ≤ 37 Vmin -5.5 · max 5.5 %6
Current regulation off time tOFFtyp 25 us6
Current sense delay time tDELAYtyp 1.6 us6
Current regulation deglitch time tDEGtyp 0.6 us6
Current regulation blanking time tBLKtyp 1.1 us6
Supply undervoltage lockout (UVLO) VUVLOVVM risingmin 4.3 · typ 4.45 · max 4.6 V6
Supply undervoltage lockout (UVLO) VUVLOVVM fallingmin 4.2 · typ 4.35 · max 4.5 V6
Supply UVLO hysteresis VUVLO_HYStyp 100 mV6
Supply undervoltage deglitch time tUVLOtyp 10 us6
Charge pump undervoltage lockout VCPUVVCP with respect to VM, VVCP fallingtyp 2.25 V6
Overcurrent protection trip point IOCPmin 6 · typ 10 A6
Overcurrent protection deglitch time tOCPtyp 3 us6
Overcurrent protection retry time tRETRYtyp 2 ms6
Thermal shutdown temperature TTSDmin 160 · typ 175 · max 190 °C6
Thermal shutdown hysteresis THYStyp 20 °C6

Pins, by the datasheet

17
1 EN/IN1
H-bridge control input with internal pulldown resistor. · p. 3
2 PH/IN2
H-bridge control input with internal pulldown resistor. · p. 3
3 nSLEEP
Logic high enables the device; logic low enters low-power sleep mode; internal pulldown resistor. · p. 3
4 nFAULT
Fault indicator pulled low during a fault; connect an external pullup resistor. · p. 3
5 VREF
External reference voltage input setting the internal current regulation limit. · p. 3
6 IPROPI
Analog current output proportional to load current. · p. 3
7 IMODE
Quad-level input selecting current regulation and overcurrent protection mode. · p. 3
8 OUT1
H-bridge output; connect to the motor or other load. · p. 3
9 PGND
Device power ground; connect to system ground. · p. 3
10 OUT2
H-bridge output; connect to the motor or other load. · p. 3
11 VM
4.5-V to 37-V supply input; connect a 0.1-uF bypass capacitor to ground and sufficient VM-rated bulk capacitance. · p. 3
12 VCP
Charge pump output; connect an X5R or X7R, 100-nF, 16-V ceramic capacitor between VCP and VM. · p. 3
13 CPH
Charge pump switching node; connect an X5R or X7R, 22-nF, VM-rated ceramic capacitor between CPH and CPL. · p. 3
14 CPL
Charge pump switching node; connect an X5R or X7R, 22-nF, VM-rated ceramic capacitor between CPH and CPL. · p. 3
15 GND
Device ground; connect to system ground. · p. 3
16 PMODE
Tri-level input selecting the H-bridge control input mode. · p. 3
— PAD
Thermal pad; connect to system ground. · p. 3

Open-source boards using it

13See all 13
  • 2 layers115.8 × 160.2 mmKicad RCJ, the printed circuit board in 3D

    Kicad RCJ

    edrobotics/rescue_maze_2024

    Code for Robocup Junior Rescue Maze 2024

    84 parts4GPL-3.0
  • 4 layers156.8 × 127 mmPayload PCB v3.1, the printed circuit board in 3D

    Payload PCB v3.1

    team-mountaineers-urc-2023/electronics

    Block diagrams, schematics, and PCB files related to the electronics subteam

    197 parts2BSD-3-Clause
  • 4 layers130 × 90 mmLizardBot1 ControlBoard v1, the printed circuit board in 3D

    LizardBot1 ControlBoard v1

    lizard-electronics/LizardBot1_ProjectFiles

    Project Files for LizardBot 1 differential-drive ROS2 robot.

    202 parts1Apache-2.0
  • 4 layers96.1 × 106.5 mmLCP PowerControl, the printed circuit board in 3D

    LCP PowerControl

    NOAA-PMEL/EDD-LCP_PistonDriver

    Repository for LCP Piston Driver PCB design and firmware

    107 parts1MIT
  • 4 layers65 × 67 mmDRV8874-Devboard, the printed circuit board in 3D

    DRV8874-Devboard

    awesomeyooner/PSD-17DB

    This is a breakout board mainly for the DRV8874, but includes other ICs that help with integrating FOC. About the name, it is short for "Polar Stepper Drive 17 - Dev Board".

    68 parts
  • 2 layers70 × 40 mmOpen sesame, the printed circuit board in 3D

    Open sesame

    croggero/open-sesame

    Sliding glass doors automated

    29 parts
  • 4 layers114.3 × 86.4 mmLinear window controller, the printed circuit board in 3D

    Linear window controller

    eflukx/Linear-motor-window-controller

    Linear quad/octa motor slide Window controller, featuring absolute position feedback control, motor current monitoring using a ESP32-S3 hi performance controller

    201 parts
  • 2 layers180 × 90 mmTMC Centrale V2.2, the printed circuit board in 3D

    TMC Centrale V2.2

    tmc-digiboys/TMC-LZ210-Command-Station-PCB

    Printed Circuit Board for the TMC-LZ210

    120 parts

Parts like it

5

Questions

Is there a KiCad symbol and footprint for the DRV8874PWP?

Yes. The symbol is EasyEDA_Cloud:DRV8874QPWPRQ1 and the footprint EasyEDA_Cloud:HTSSOP-16_L5.0-W4.4-P0.65-LS6.4-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DRV8874PWP?

HTSSOP-16-EP, with 17 pins. Its footprint is drawn on this page.

Where is the DRV8874PWP datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the DRV8874PWP?

JLCPCB lists it as part C1855818, with 12,551 in stock; the sellers' links on this page open their listings.

What can replace the DRV8874PWP?

Parts like it in the library: the DRV8876NPWPR by Texas Instruments, the DRV8876QPWPRQ1 by Texas Instruments, the DRV8874QPWPRQ1 by Texas Instruments and the PT2432-HT by PTC. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the DRV8874PWP?

13 boards in 11 repositories on GitHub; the most starred are listed on this page, with their KiCad files.