
DRV8836DSS
Texas InstrumentsExtended
-40℃~+85℃ 1.5A 2 2V~7V 305mΩ 90nA Yes WSON-12-EP(2x3) Brushed DC Motor Drivers ROHS
- Part id
- ti/DRV8836DSS
- Category
- Stepper Motor Driver
- Package
- WSON-12-EP(2x3)
- Pins
- 13
- In stock
- 249 at JLCPCB (C191002)
- Used on
- 1 open-source board
Overview
The DRV8836DSS is a stepper Motor Driver made by Texas Instruments in a WSON-12-EP(2x3) package with 13 pins. -40℃~+85℃ 1.5A 2 2V~7V 305mΩ 90nA Yes WSON-12-EP(2x3) Brushed DC Motor Drivers ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:DRV8836DSSR, from EasyEDA) and its footprint (EasyEDA_Cloud:WSON-12_L3.0-W2.0-P0.50-BL-EP, from EasyEDA), ready for a KiCad board. 249 are in stock at JLCPCB (part C191002). 1 open-source board in 1 repository on GitHub use it.
Symbol
Footprint
From the datasheet
14- Supply, least
- 2 V · VCC, recommended operating min · p. 4
- Supply, most
- 7 V · VCC, recommended operating max · p. 4
- Supply, absolute maximum
- 7 V · VCC, absolute max · p. 4
- Works from
- -40 °C · Operating temperature min, DRV8836DSSR · p. 17
- Works up to
- 85 °C · Operating temperature max, DRV8836DSSR · p. 17
- Junction, hottest
- 150 °C · Operating junction temperature absolute max · p. 4
- Takes working
- 1.7 mA · VCC operating current typical, fPWM = 50 kHz, no load · p. 5
- Takes at most
- 2.5 mA · VCC operating current max, fPWM = 50 kHz, no load · p. 5
- Takes asleep
- 40 nA · VCC sleep current typical, VCC = 5 V, nSLEEP = 0 V, all inputs 0 V · p. 5
- Gives
- 1.5 A · Continuous H-bridge output current max per channel; thermal limits apply · p. 4
- Current limit
- 1.6 A · Overcurrent protection trip level min · p. 5
- Junction to air (DSS (WSON))
- 50.4 K/W · Junction-to-ambient thermal resistance · p. 4
- Junction to board (DSS (WSON))
- 19.9 K/W · Junction-to-board thermal resistance · p. 4
- Junction to case (DSS (WSON))
- 58 K/W · Junction-to-case top thermal resistance · p. 4
What it is and has
6- Motor driver
- Dual H-bridge · p. 1
- Parallel drive current
- 3 A · p. 1
- Control interface
- PWM or PHASE/ENABLE · p. 1
- Sleep control
- Dedicated nSLEEP input · p. 1
- Package
- WSON, 12 pins, 2.00 mm × 3.00 mm · p. 1
- Protection
- Undervoltage, overcurrent, overtemperature · p. 9
Around it
2- cap 0.1-μF (minimum)
- between VCC and GND; Ceramic supply bypass capacitor. · p. 3
- cap 10 µF
- between VCC and GND; Supply capacitor shown in the parallel mode application. · p. 11
Specifications
33| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Power supply voltage, VCC VCC | min -0.3 · max 7 V | 4 | |
| Digital input pin voltage | Maximum: VCC + 0.5 V | min -0.5 V | 4 |
| Continuous motor drive output current per H-bridge | Power dissipation and thermal limits must be observed | min -1.5 · max 1.5 A | 4 |
| Operating junction temperature TJ | min -40 · max 150 °C | 4 | |
| Storage temperature Tstg | min -60 · max 150 °C | 4 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 | min -2000 · max 2000 V | 4 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101 | min -1500 · max 1500 V | 4 |
| Device power supply voltage VCC | TA = 25°C | min 2 · max 7 V | 4 |
| Logic level input voltage VIN | TA = 25°C; maximum: VCC | min 0 V | 4 |
| H-bridge output current IOUT | TA = 25°C; power dissipation and thermal limits must be observed | min 0 · max 1.5 A | 4 |
| Externally applied PWM frequency fPWM | TA = 25°C | min 0 · max 250 kHz | 4 |
| Junction-to-ambient thermal resistance RθJA | DSS (WSON), 12 PINS | typ 50.4 °C/W | 4 |
| Junction-to-case (top) thermal resistance RθJC(top) | DSS (WSON), 12 PINS | typ 58 °C/W | 4 |
| Junction-to-board thermal resistance RθJB | DSS (WSON), 12 PINS | typ 19.9 °C/W | 4 |
| Junction-to-top characterization parameter ψJT | DSS (WSON), 12 PINS | typ 0.9 °C/W | 4 |
| Junction-to-board characterization parameter ψJB | DSS (WSON), 12 PINS | typ 20 °C/W | 4 |
| Junction-to-case (bottom) thermal resistance RθJC(bot) | DSS (WSON), 12 PINS | typ 6.9 °C/W | 4 |
| VCC operating supply current IVCC | TA = 25°C, VCC = 5 V; fPWM = 50 kHz, no load | typ 1.7 · max 2.5 mA | 5 |
| VCC sleep mode supply current ICCQ | TA = 25°C, VCC = 5 V; nSLEEP = 0 V, all inputs 0 V | typ 40 · max 95 nA | 5 |
| VCC sleep mode supply current ICCQ | TA = 25°C; VCC = 3 V, nSLEEP = 0 V, all inputs 0 V | typ 10 nA | 5 |
| VCC undervoltage lockout voltage VUVLO | TA = 25°C; VCC rising | max 2 V | 5 |
| VCC undervoltage lockout voltage VUVLO | TA = 25°C; VCC falling | max 1.9 V | 5 |
| Input low current IIL | TA = 25°C, VCC = 5 V; VIN = 0 | min -5 · max 5 uA | 5 |
| Input high current IIH | TA = 25°C, VCC = 5 V; VIN = 3.3 V | max 50 uA | 5 |
| Pulldown resistance RPD | TA = 25°C, VCC = 5 V | typ 100 kΩ | 5 |
| HS + LS FET on resistance RDS(ON) | TA = 25°C; VCC = 3 V, I O = 800 mA, TJ = 25°C | typ 370 · max 420 mΩ | 5 |
| HS + LS FET on resistance RDS(ON) | TA = 25°C; VCC = 5 V, IO = 800 mA, TJ = 25°C | typ 305 · max 355 mΩ | 5 |
| OFF-state leakage current IOFF | TA = 25°C, VCC = 5 V; maximum magnitude ±200 nA | max 200 nA | 5 |
| Overcurrent protection trip level IOCP | TA = 25°C, VCC = 5 V | min 1.6 · max 3.5 A | 5 |
| Overcurrent deglitch time tDEG | TA = 25°C, VCC = 5 V | typ 1 us | 5 |
| Overcurrent protection retry time tOCR | TA = 25°C, VCC = 5 V | typ 1 ms | 5 |
| Output dead time tDEAD | TA = 25°C, VCC = 5 V | typ 100 ns | 5 |
| Thermal shutdown temperature tTSD | TA = 25°C, VCC = 5 V; Die temperature | min 150 · typ 160 · max 180 °C | 5 |
Pins, by the datasheet
13- 1 VCC
- Device and motor supply; bypass to GND with a minimum 0.1-uF ceramic capacitor. · p. 3
- 2 AOUT1
- Bridge A output 1; connect to motor winding A. · p. 3
- 3 AOUT2
- Bridge A output 2; connect to motor winding A. · p. 3
- 4 BOUT1
- Bridge B output 1; connect to motor winding B. · p. 3
- 5 BOUT2
- Bridge B output 2; connect to motor winding B. · p. 3
- 6 GND
- Device ground. · p. 3
- 7 BIN2/BENBL
- Bridge B input 2/ENABLE input; high sets BOUT2 high in IN/IN mode or enables bridge B in PH/EN mode; internal pulldown. · p. 3
- 8 BIN1/BPHASE
- Bridge B input 1/PHASE input; high sets BOUT1 high in IN/IN mode or sets bridge B direction in PH/EN mode; internal pulldown. · p. 3
- 9 AIN2/AENBL
- Bridge A input 2/ENABLE input; high sets AOUT2 high in IN/IN mode or enables bridge A in PH/EN mode; internal pulldown. · p. 3
- 10 AIN1/APHASE
- Bridge A input 1/PHASE input; high sets AOUT1 high in IN/IN mode or sets bridge A direction in PH/EN mode; internal pulldown. · p. 3
- 11 MODE
- Input mode select; low selects IN/IN mode and high selects PH/EN mode; internal pulldown. · p. 3
- 12 nSLEEP
- Active low places the part in low-power sleep state; internal pulldown. · p. 3
- Thermal pad GND
- Device ground; thermally connect the exposed pad to PCB copper to dissipate heat. · p. 3
Ordering codes, by the datasheet
4- DRV8836DSSR
- WSON (DSS), 12 pins · 3000-piece large tape and reel; -40 to 85 °C operating temperature. · p. 17
- DRV8836DSSR.B
- WSON (DSS), 12 pins · 3000-piece large tape and reel; -40 to 85 °C operating temperature; no other difference stated. · p. 17
- DRV8836DSSRG4
- WSON (DSS), 12 pins · 3000-piece large tape and reel; -40 to 85 °C operating temperature; no other difference stated. · p. 17
- DRV8836DSSRG4.B
- WSON (DSS), 12 pins · 3000-piece large tape and reel; -40 to 85 °C operating temperature; no other difference stated. · p. 17
Open-source boards using it
1- 4 layers28.9 × 51.8 mm

Parts like it
3DRV8839DSS
WSON-12-EP(2x3)-40℃~+150℃ 1 1.8A 1.8V~7V 280mΩ Yes WSON-12-EP(2x3) Brushed DC Motor Drivers ROHSTexas InstrumentsStepper Motor DriverHT8835ARDZ
WSON-12-EP(2x3)-40℃~+85℃ 0V~11V 1.5A 2 2V~7V 305mΩ WSON-12-EP(2x3) Stepper Motor Driver ROHSHTCSEMIStepper Motor DriverDRV8835DSS
WSON-12-EP(2x3)-40℃~+150℃ 1.5A 2 2V~7V 305mΩ 95nA Yes WSON-12-EP(2x3) Brushed DC Motor Drivers ROHSTexas InstrumentsStepper Motor Driver
Questions
Is there a KiCad symbol and footprint for the DRV8836DSS?
Yes. The symbol is EasyEDA_Cloud:DRV8836DSSR and the footprint EasyEDA_Cloud:WSON-12_L3.0-W2.0-P0.50-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the DRV8836DSS?
WSON-12-EP(2x3), with 13 pins. Its footprint is drawn on this page.
Where is the DRV8836DSS datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the DRV8836DSS?
JLCPCB lists it as part C191002, with 249 in stock; the sellers' links on this page open their listings.
What can replace the DRV8836DSS?
Parts like it in the library: the DRV8839DSS by Texas Instruments, the HT8835ARDZ by HTCSEMI and the DRV8835DSS by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the DRV8836DSS?
1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.