Skip to the content
1234567891011121314151617181920212223242526272829

DRV8313PWP

Texas InstrumentsExtended

HTSSOP-28-EP-4.5mm Brushless DC (BLDC) Motor Driver ROHS

Part id
ti/DRV8313PWP
Category
Motor Driver ICs
Package
HTSSOP-28-EP-4.5mm
Pins
29
In stock
0 at JLCPCB (C2863441)
Used on
20 open-source boards

Overview

The DRV8313PWP is a motor Driver IC made by Texas Instruments in a HTSSOP-28-EP-4.5mm package with 29 pins. HTSSOP-28-EP-4.5mm Brushless DC (BLDC) Motor Driver ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:DRV8313PWP, from EasyEDA) and its footprint (EasyEDA_Cloud:TSSOP-28_L9.7-W4.4-P0.65-LS6.4-TL-EP-2, from EasyEDA), ready for a KiCad board. JLCPCB lists it (part C2863441). 20 open-source boards in 19 repositories on GitHub use it.

Symbol

29EP28GND27IN126EN125IN224EN223IN322EN321NC20GND19COMPO#18FAULT#17SLEEP#16RESET#15V3P3OUT14GND13COMPN12COMPP11VM10PGND39OUT38OUT27PGND26PGND15OUT14VM3VCP2CP21CP1
EasyEDA_Cloud:DRV8313PWPFrom EasyEDA

Footprint

1234567891011121314151617181920212223242526272829
EasyEDA_Cloud:TSSOP-28_L9.7-W4.4-P0.65-LS6.4-TL-EP-2From EasyEDA

From the datasheet

14
Supply, least
8 V · VM, recommended operating min · p. 5
Supply, most
60 V · VM, recommended operating max · p. 5
Supply, absolute maximum
65 V · VM, absolute maximum · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 5
Works up to
125 °C · Operating ambient temperature max · p. 5
Junction, hottest
150 °C · Operating junction temperature max · p. 4
Takes working
1 mA · VM operating supply current typical, VM = 24 V, fPWM < 50 kHz · p. 6
Takes at most
5 mA · VM operating supply current max, VM = 24 V, fPWM < 50 kHz · p. 6
Takes asleep
500 µA · VM sleep-mode supply current typical, VM = 24 V · p. 6
Current limit
5 A · Overcurrent protection trip level typical · p. 6
A pin gives at most
10 mA · nFAULT, nCOMPO open-drain output current absolute max · p. 4
Junction to air (PWP (HTSSOP))
31.6 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to board (PWP (HTSSOP))
5.6 K/W · Junction-to-board thermal resistance · p. 5
Junction to case (PWP (HTSSOP))
15.9 K/W · Junction-to-case (top) thermal resistance · p. 5

What it is and has

8
Driver channels
Three individually controllable half-H bridges · p. 1
Peak drive current
2.5 A · p. 1
Bridge control
Independent half-H-bridge control · p. 1
Comparator
Uncommitted comparator for current limit or other functions · p. 1
Internal regulator
3.3-V, 10-mA LDO · p. 1
Sleep mode
Standby operation · p. 1
Package option
28-pin HTSSOP PowerPAD · p. 1
Package option
36-pin VQFN · p. 1

Around it

6
cap 0.01-µF
between CPH and CPL; VM-rated ceramic capacitor. · p. 3
cap 0.1-µF
between VCP and VM; 16-V ceramic capacitor. · p. 4
cap 0.47-µF
between V3P3 and GND; 6.3-V ceramic bypass capacitor. · p. 4
cap 0.1-µF
between VM and GND; Two capacitors for each VM pin, plus one bulk capacitor rated for VM. · p. 4
res not specified
between nCOMPO and external pullup; External pullup required for the open-drain comparator output. · p. 3
res not specified
between nFAULT and external pullup; External pullup required for the open-drain fault output. · p. 3

Specifications

61
ParameterConditionsAs printedPage
Power-supply voltage (VM)Over operating free-air temperature rangemin -0.3 · max 65 V4
Power supply voltage ramp rate (VM)Over operating free-air temperature rangemin 0 · max 2 V/us4
Charge pump voltage (VCP, CPH)Maximum VM + 12 Vmin -0.3 V4
Charge pump negative switching pin (CPL)Maximum VMmin -0.3 V4
Internal regulator current output (V3P3)min 0 · max 10 mA4
Internal regulator voltage (V3P3)min -0.3 · max 3.8 V4
Control pin voltage (nRESET, nSLEEP, nFAULT, nCOMPO, ENx, INx)min -0.5 · max 7 V4
Comparator input-voltage (COMPP, COMPN)min -0.5 · max 7 V4
Open drain output current (nFAULT, nCOMPO)min 0 · max 10 mA4
Continuous phase node pin voltage (OUTx)Maximum VM + 0.7 Vmin -0.7 V4
Continuous 1/2-H-bridge source voltage (PGNDx)min -600 · max 600 mV4
Operating junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -60 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; rated ±3000 Vmax 3000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101; rated ±1500 Vmax 1500 V4
Motor power-supply voltage VMBoth VM pins must be connected to the same supply voltagemin 8 · max 60 V5
Digital pin voltage VINmin 0 · max 5.5 V5
Applied PWM signal on ENx, INx fPWMmin 0 · max 250 kHz5
PGNDx pin voltage VGNDXmin -500 · max 500 mV5
V3P3 load current IV3P3Power dissipation and thermal limits must be observedmin 0 · max 10 mA5
Operating ambient temperature TAmin -40 · max 125 °C5
Junction-to-ambient thermal resistance RθJAPWP (HTSSOP), 28 pinstyp 31.6 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)PWP (HTSSOP), 28 pinstyp 15.9 °C/W5
Junction-to-board thermal resistance RθJBPWP (HTSSOP), 28 pinstyp 5.6 °C/W5
Junction-to-top characterization parameter ψJTPWP (HTSSOP), 28 pinstyp 0.2 °C/W5
Junction-to-board characterization parameter ψJBPWP (HTSSOP), 28 pinstyp 5.5 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)PWP (HTSSOP), 28 pinstyp 1.4 °C/W5
VM operating supply current IVMVM = 24 V, fPWM < 50 kHztyp 1 · max 5 mA6
VM sleep-mode supply current IVMQVM = 24 Vtyp 500 · max 800 uA6
V3P3 voltage V3P3IOUT = 0 to 10 mAmin 3.1 · typ 3.3 · max 3.52 V6
Input low voltage VILnSLEEP, ENx, INxtyp 0.6 · max 0.7 V6
Input high voltage VIHnSLEEP, ENx, INxmin 2.2 · max 5.25 V6
Input hysteresis VHYSnSLEEP, ENx, INxmin 50 · max 600 mV6
Input low current IILVIN = 0; nSLEEP, ENx, INxmin -5 · max 5 uA6
Input high current IIHVIN = 3.3 V; nSLEEP, ENx, INxmax 100 uA6
Pulldown resistance RPDnSLEEP, ENx, INxtyp 100 kΩ6
Output low voltage VOLIO = 5 mA; nFAULT and nCOMPOmax 0.5 V6
Output high leakage current IOHVO = 3.3 V; nFAULT and nCOMPOmax 1 uA6
Common-mode input-voltage range VCMCOMPP, COMPN, nCOMPOmin 0 · max 5 V6
Input offset voltage VIOCOMPP, COMPN, nCOMPOmin -7 · max 7 mV6
Input bias current IIBCOMPP, COMPN, nCOMPOmin -300 · max 300 nA6
Response time tR100-mV step with 10-mV overdrivemax 2 us6
High-side FET ON-resistance rDS(on)VM = 24 V, IO = 1 A, TJ = 25°Ctyp 0.24 Ω6
High-side FET ON-resistance rDS(on)VM = 24 V, IO = 1 A, TJ = 85°C; specification based on design and characterization datatyp 0.29 · max 0.39 Ω6
Low-side FET ON-resistance rDS(on)VM = 24 V, IO = 1 A, TJ = 25°Ctyp 0.24 Ω6
Low-side FET ON-resistance rDS(on)VM = 24 V, IO = 1 A, TJ = 85°C; specification based on design and characterization datatyp 0.29 · max 0.39 Ω6
Off-state leakage current IOFFmin -2 · max 2 uA6
VM undervoltage lockout voltage VUVLOVM risingtyp 6.3 · max 8 V6
Overcurrent protection trip level IOCPmin 3 · typ 5 A6
Overcurrent protection deglitch time tOCPtyp 5 us6
Thermal shutdown temperature TTSDDie temperature; specification based on design and characterization datamin 150 · typ 160 · max 180 °C6
Thermal shutdown hysteresis THYSDie temperature; specification based on design and characterization datatyp 35 °C6
Delay time, ENx high to OUTx high t1TA = 25°C, VM = 24 V, RL = 20 Ω; INx = 1min 130 · max 330 ns7
Delay time, ENx low to OUTx low t2TA = 25°C, VM = 24 V, RL = 20 Ω; INx = 1min 275 · max 475 ns7
Delay time, ENx high to OUTx low t3TA = 25°C, VM = 24 V, RL = 20 Ω; INx = 0min 100 · max 300 ns7
Delay time, ENx low to OUTx high t4TA = 25°C, VM = 24 V, RL = 20 Ω; INx = 0min 200 · max 400 ns7
Delay time, INx high to OUTx high t5TA = 25°C, VM = 24 V, RL = 20 Ω; ENx = 1min 300 · max 500 ns7
Delay time, INx low to OUTx low t6TA = 25°C, VM = 24 V, RL = 20 Ω; ENx = 1min 275 · max 475 ns7
Output rise time, resistive load to GND trTA = 25°C, VM = 24 V, RL = 20 Ωmin 30 · max 150 ns7
Output fall time, resistive load to GND tfTA = 25°C, VM = 24 V, RL = 20 Ωmin 30 · max 150 ns7
Output dead time tDEADTA = 25°C, VM = 24 V, RL = 20 Ω; specified by design and characterization datatyp 90 ns7

Pins, by the datasheet

29
1 CPL
Charge pump; connect a VM-rated 0.01-uF ceramic capacitor between CPH and CPL. · p. 3
2 CPH
Charge pump; connect a VM-rated 0.01-uF ceramic capacitor between CPH and CPL. · p. 3
3 VCP
Charge pump; connect a 16-V, 0.1-uF ceramic capacitor to VM. · p. 4
4 VM
Motor power supply; bypass to GND with two 0.1-uF capacitors for each pin plus one bulk capacitor rated for VM. · p. 4
5 OUT1
Half-H bridge output; connect to the load. · p. 4
6 PGND1
Low-side FET source; connect to GND or to a low-side current-sense resistor. · p. 4
7 PGND2
Low-side FET source; connect to GND or to a low-side current-sense resistor. · p. 4
8 OUT2
Half-H bridge output; connect to the load. · p. 4
9 OUT3
Half-H bridge output; connect to the load. · p. 4
10 PGND3
Low-side FET source; connect to GND or to a low-side current-sense resistor. · p. 4
11 VM
Motor power supply; bypass to GND with two 0.1-uF capacitors for each pin plus one bulk capacitor rated for VM. · p. 4
12 COMPP
Uncommitted comparator positive input. · p. 3
13 COMPN
Uncommitted comparator negative input. · p. 3
14 GND
Device ground; connect to system ground. · p. 3
15 V3P3
Internal regulator supply; bypass to GND with a 6.3-V, 0.47-uF ceramic capacitor; supports up to 10-mA external load. · p. 4
16 nRESET
Active-low reset initializes internal logic, clears faults, and disables outputs; internal pulldown. · p. 3
17 nSLEEP
High enables the device; low enters low-power sleep mode; internal pulldown. · p. 4
18 nFAULT
Fault indication pulls low on a fault; requires an external pullup. · p. 3
19 nCOMPO
Uncommitted comparator output; requires an external pullup. · p. 3
20 GND
Device ground; connect to system ground. · p. 3
21 NC
No internal connection; recommended net given in block diagram, if any. · p. 3
22 EN3
High enables the half-H bridge channel; internal pulldown. · p. 3
23 IN3
High pulls the bridge high and low pulls it low; no effect when ENx is low; internal pulldown. · p. 3
24 EN2
High enables the half-H bridge channel; internal pulldown. · p. 3
25 IN2
High pulls the bridge high and low pulls it low; no effect when ENx is low; internal pulldown. · p. 3
26 EN1
High enables the half-H bridge channel; internal pulldown. · p. 3
27 IN1
High pulls the bridge high and low pulls it low; no effect when ENx is low; internal pulldown. · p. 3
28 GND
Device ground; connect to system ground. · p. 3
Thermal pad Thermal pad
Must be connected to ground. · p. 4

Open-source boards using it

20See all 20
  • 2 layers55 × 54 mmCarte Major Tom, the printed circuit board in 3D

    Carte Major Tom

    pollen-robotics/Orbita_3d_R1

    All you need to make your own Orbita_3d Joint!

    78 parts18
  • 4 layers35 × 35 mmFoc8313, the printed circuit board in 3D

    Foc8313

    williamhaarhoff/foc8313

    Highly compact field oriented controller based on the DRV8313 IC

    155 parts9
  • 2 layers50 × 40 mmBldc controller, the printed circuit board in 3D

    Bldc controller

    nerdmaennchen/motorcontroller-hw

    An open hardware PCB to control motors with (BLDC and DC)

    67 parts6MIT
  • 2 layers32.3 × 87.6 mmESP32-Gimbal, the printed circuit board in 3D

    ESP32-Gimbal

    Visaging/ESP32-Gimbal

    A high-performance, open-source 3-axis smartphone gimbal built from scratch using a custom PCB and the SimpleFOC library. It features real-time stabilization, native USB-C programming, and custom motion modes.

    60 parts4MIT
  • 4 layers37.1 × 41 mmServoLess, the printed circuit board in 3D

    ServoLess

    Aiano/ServoLess

    Wireless and brushless DC Servo.

    98 parts2
  • 2 layers142.5 × 99 mmPCB Prrojects, the printed circuit board in 3D

    PCB Prrojects

    PipistarXu/stm32g431-lm2596-board

    24 parts1MIT
  • 2 layers24.1 × 4.9 mmL103 CANUSB DRV8313, the printed circuit board in 3D

    L103 CANUSB DRV8313

    bjthemost-hub/l103-drv8313-as5600

    Joint motor driver: CH32L103 + DRV8313 + AS5600. KiCad hardware, FOC firmware, PC tools, 2-stage planetary gearbox (J, 25:1). MIT.

    92 partsMIT

Questions

Is there a KiCad symbol and footprint for the DRV8313PWP?

Yes. The symbol is EasyEDA_Cloud:DRV8313PWP and the footprint EasyEDA_Cloud:TSSOP-28_L9.7-W4.4-P0.65-LS6.4-TL-EP-2, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DRV8313PWP?

HTSSOP-28-EP-4.5mm, with 29 pins. Its footprint is drawn on this page.

Where is the DRV8313PWP datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the DRV8313PWP?

JLCPCB lists it as part C2863441, with 0 in stock; the sellers' links on this page open their listings.

Which open-source boards use the DRV8313PWP?

20 boards in 19 repositories on GitHub; the most starred are listed on this page, with their KiCad files.