
DRV8305NPHPR
Texas InstrumentsExtended
-40℃~+125℃ 0V~800mV 200ns 200ns 2V 3 4.4V~45V MOSFET Three Phase Under Voltage Protection、Over Voltage Protection、Over Current Protection、Overtemperature protection (OTP) HTQFP-48(7x7) Gate Drivers ROHS
- Part id
- ti/DRV8305NPHPR
- Category
- Brushless DC (BLDC) Motor Driver
- Package
- HTQFP-48(7x7)
- Pins
- 48
- In stock
- 489 at JLCPCB (C75602)
- Used on
- 3 open-source boards
Overview
The DRV8305NPHPR is a brushless DC (BLDC) Motor Driver made by Texas Instruments in a HTQFP-48(7x7) package with 49 pins. -40℃~+125℃ 0V~800mV 200ns 200ns 2V 3 4.4V~45V MOSFET Three Phase Under Voltage Protection、Over Voltage Protection、Over Current Protection、Overtemperature protection (OTP) HTQFP-48(7x7) Gate Drivers ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:DRV8305NPHPR, from EasyEDA) and its footprint (EasyEDA_Cloud:HTQFP-48_L7.0-W7.0-P0.50-LS9.0-BL-EP5.1, from EasyEDA), ready for a KiCad board. 489 are in stock at JLCPCB (part C75602). 3 open-source boards in 2 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
13- Supply, least
- 4.4 V · PVDD, recommended operating min · p. 6
- Supply, most
- 45 V · PVDD, recommended operating max · p. 6
- Supply, absolute maximum
- 45 V · PVDD, absolute maximum · p. 5
- Works from
- -40 °C · TA, operating ambient min · p. 6
- Works up to
- 125 °C · TA, operating ambient max · p. 6
- Junction, hottest
- 150 °C · TJ, operating junction max · p. 5
- Takes working
- 15 mA · PVDD operating typical; EN_GATE enabled, LDO enabled at no load, outputs HiZ · p. 7
- Takes asleep
- 60 µA · PVDD sleep typical; EN_GATE disabled, LDO disabled, ready for WAKE · p. 7
- Takes asleep
- 4 mA · PVDD standby typical; EN_GATE disabled, LDO enabled at no load · p. 7
- A pin gives at most
- 7 mA · nFAULT and PWRGD open-drain sink absolute max · p. 5
- Junction to air (PHP (HTQFP))
- 26.6 K/W · junction-to-ambient thermal resistance · p. 6
- Junction to case (PHP (HTQFP))
- 12.9 K/W · junction-to-case top thermal resistance · p. 6
- Junction to board (PHP (HTQFP))
- 7.6 K/W · junction-to-board thermal resistance · p. 6
What it is and has
19- Device option
- Voltage reference · p. 1
- Peak gate drive currents
- 1.25 A and 1 A · p. 1
- Current-shunt amplifiers
- 3 integrated · p. 1
- PWM control
- 3-PWM or 6-PWM, up to 200 kHz · p. 1
- PWM commutation
- Single PWM mode · p. 1
- Digital interface
- 3.3 V and 5 V · p. 1
- Gate driver
- Charge pump supports 100% duty cycle · p. 1
- Package
- Thermally enhanced 48-pin HTQFP · p. 1
- Protection
- Fault diagnostics and MCU watchdog · p. 1
- Protection
- Programmable dead-time control · p. 1
- Protection
- MOSFET shoot-through prevention · p. 1
- Protection
- MOSFET VDS overcurrent monitors · p. 1
- Protection
- Gate-driver fault detection · p. 1
- Protection
- Reverse battery-protection support · p. 1
- Protection
- Limp home-mode support · p. 1
- Protection
- Overtemperature warning and shutdown · p. 1
- Charge-pump gate driver
- 100% duty cycle · p. 1
- Current shunt amplifiers
- 3, independently programmable and calibrated · p. 23
- Current shunt amplifier gain
- 10, 20, 40 and 80 V/V, programmable through SPI · p. 23
Around it
14- cap 4.7 µF
- between PVDD and GND; CPVDD; ceramic, rated for PVDD. · p. 5
- cap 1 µF
- between AVDD and GND; CAVDD; ceramic, rated for 6.3 V. · p. 5
- cap 1 µF
- between DVDD and GND; CDVDD; ceramic, rated for 6.3 V. · p. 5
- cap 2.2 µF
- between VCPH and PVDD; CVCPH; ceramic, rated for 16 V. · p. 5
- cap 1 µF
- between VCP_LSD and GND; CVCP_LSD; ceramic, rated for 16 V. · p. 5
- cap 0.047 µF
- between CP1H and CP1L; CCP1; ceramic, rated for PVDD. · p. 5
- cap 0.047 µF
- between CP2H and CP2L; CCP2; ceramic, rated for PVDD × 2. · p. 5
- cap 1 µF
- between VREG and GND; CVREG; ceramic, rated for 6.3 V. · p. 5
- res 100 Ω
- between VDRAIN and PVDD; RVDRAIN; series resistor between VDRAIN and high-side MOSFET drain. · p. 5
- res 1-10 kΩ
- between nFAULT and VCC; RnFAULT; pullup to MCU power supply. · p. 5
- res 1-10 kΩ
- between PWRGD and VCC; RPWRGD; pullup to MCU power supply. · p. 5
- cap 1 µF
- between DVDD and GND; External bypass capacitor. · p. 25
- cap 1 µF
- between AVDD and GND; External bypass capacitor. · p. 25
- res 100 Ω
- between VDRAIN and drain of the external high-side MOSFET; Recommended current limiting resistor for reverse supply protection. · p. 30
Specifications
180| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Power supply voltage (PVDD) | Referenced to GND; over operating free-air temperature range | min -0.3 · max 45 V | 5 |
| Power supply voltage ramp rate (VM) | min 0 · max 2 V/us | 5 | |
| Charge pump voltage (CP1H,CP1L, CP2L,CP2H, VCPH, VCP_LSD) | Maximum PVDD + 12 V | min -0.3 V | 5 |
| High side gate driver voltage (GHA, GHB, GHC) | min -3 · max 57 V | 5 | |
| Low-side gate driver voltage (GHA, GHB, GHC) | min -2 · max 12 V | 5 | |
| High side gate driver source pin voltage (SHA, SHB, SHC) | min -5 · max 45 V | 5 | |
| Low-side gate driver source pin voltage (SLA, SLB, SLC) | min -3 · max 5 V | 5 | |
| Internal phase clamp pin voltage difference {(GHA-SHA), (GHB-SHB), (GHC-SHC), (GLA-SLA), (GLB-SLB), (GLC-SLC)} | min -0.3 · max 15 V | 5 | |
| Drain pin voltage drain (VDRAIN) | min -0.3 · max 45 V | 5 | |
| Max source current (VDRAIN) – limit current with external series resistor | min -20 mA | 5 | |
| Max sink current (VDRAIN) | max 2 mA | 5 | |
| Voltage difference between supply and VDRAIN (PVDD-VDRAIN) | min -10 · max 10 V | 5 | |
| Control pin voltage range (INHA, INLA, INHB, INLB, INHC, INLC, EN_GATE, SCLK, SDI, SCS, SDO, nFAULT, PWRGD) | min -0.3 · max 5.5 V | 5 | |
| Open drain pins skink current (nFAULT, PWRGD) | max 7 mA | 5 | |
| Wake pin voltage (WAKE) | min -0.3 · max 45 V | 5 | |
| Wake pin sink current (WAKE) – limit with external series resistor | max 1 mA | 5 | |
| Sense amp voltage (SPA, SNA, SPB, SNB, SPC, SNC) | min -2 · max 5 V | 5 | |
| Externally applied reference voltage (VREG) – when vreg_vref = 1 | vreg_vref = 1 | min -0.3 · max 5.5 V | 5 |
| Externally applied reference sink current (VREG) – when vreg_vref = 1 | vreg_vref = 1 | max 100 uA | 5 |
| Operating ambient temperature, TA TA | min -40 · max 125 °C | 5 | |
| Operating junction temperature, TJ TJ | min -40 · max 150 °C | 5 | |
| Storage temperature, Tstg Tstg | min -55 · max 150 °C | 5 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 V | max 2000 V | 6 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; ±500 V | max 500 V | 6 |
| Power supply voltage VPVDD | Over operating free-air temperature range | min 4.4 · max 45 V | 6 |
| Power supply voltage ramp rate (PVDD = 0 to 20 V rising <3-mA pin sink current) VPVDDRAMP | PVDD = 0 to 20 V rising; <3-mA pin sink current | max 1 V/us | 6 |
| Total voltage drop from PVDD to SH_X pins VPVDD-SH_X | max 4.5 V | 6 | |
| External load on VCPH pin (current limit resistor in series to load) ISRC_VCPH | Current limit resistor in series to load | max 10 mA | 6 |
| Maximum external capacitive load on shunt amplifier (no external resistor on output, excluding internal pin capacitance) CO_OPA | No external resistor on output; excluding internal pin capacitance | max 60 pF | 6 |
| nFAULT sink current (VnFAULT = 0.3 V) InFAULT | VnFAULT = 0.3 V | max 7 mA | 6 |
| Operating switching frequency of gate driver Fgate | max 200 kHz | 6 | |
| Total average gate driver current (HS + LS) – charge pump limited IGATE | HS + LS; charge pump limited | max 30 mA | 6 |
| Operating ambient temperature TA | min -40 · max 125 °C | 6 | |
| Junction-to-ambient thermal resistance RθJA | DRV8305; PHP (HTQFP); 48 PINS | typ 26.6 °C/W | 6 |
| Junction-to-case (top) thermal resistance RθJC(top) | DRV8305; PHP (HTQFP); 48 PINS | typ 12.9 °C/W | 6 |
| Junction-to-board thermal resistance RθJB | DRV8305; PHP (HTQFP); 48 PINS | typ 7.6 °C/W | 6 |
| Junction-to-top characterization parameter ψJT | DRV8305; PHP (HTQFP); 48 PINS | typ 0.3 °C/W | 6 |
| Junction-to-board characterization parameter ψJB | DRV8305; PHP (HTQFP); 48 PINS | typ 7.5 °C/W | 6 |
| Junction-to-case (bottom) thermal resistance RθJC(bot) | DRV8305; PHP (HTQFP); 48 PINS | typ 0.6 °C/W | 6 |
| PVDD operating voltage VPVDD | TA = 25°C | min 4.4 · max 45 V | 7 |
| PVDD operating supply current IPVDD_Operating | EN_GATE = enabled; LDO reg = enabled at no load; outputs HiZ; PVDD = 4.4 to 45 V; TA = 25°C | typ 15 mA | 7 |
| PVDD standby supply current IPVDD_Standby | EN_GATE = disabled; LDO reg = enabled at no load; PVDD = 4.4 to 45 V; TA = 25°C | typ 4 · max 7 mA | 7 |
| PVDD sleep supply current IPVDD_Sleep | EN_GATE = disabled; LDO reg = disabled; ready for WAKE; PVDD = 4.4 to 45 V; TA = 25°C | typ 60 · max 175 uA | 7 |
| Internal regulator voltage VAVDD | PVDD = 5.3 to 45 V; TA = 25°C | min 4.85 · typ 5 · max 5.15 V | 7 |
| Internal regulator voltage VDVDD | PVDD = 4.4 to 45 V; TA = 25°C | typ 3.3 V | 7 |
| Input logic low voltage VIL | INHA, INLA, INHB, INLB, INHC, INLC, EN_GATE, SCLK, nSCS; TA = 25°C | min 0 · max 0.8 V | 7 |
| Input logic high voltage VIH | INHA, INLA, INHB, INLB, INHC, INLC, EN_GATE, SCLK, nSCS; TA = 25°C | min 2 · max 5 V | 7 |
| Internal pulldown resistor RPD | To GND; logic-level inputs; TA = 25°C | typ 100 kΩ | 7 |
| Output logic low voltage VOL | nFAULT, SDO, PWRGD; IO = 5 mA; TA = 25°C | max 0.5 V | 7 |
| Output logic high voltage VOH | nFAULT, SDO, PWRGD; TA = 25°C | min 2.4 V | 7 |
| Output logic high leakage IOH | nFAULT, SDO, PWRGD; VO = 3.3 V; TA = 25°C | min -1 · max 1 uA | 7 |
| Output logic low voltage VIL_WAKE | WAKE; TA = 25°C | min 1.1 · max 1.41 V | 7 |
| Output logic high voltage VIH_WAKE | WAKE; TA = 25°C | min 1.42 · max 1.75 V | 7 |
| High-side gate driver Vgs voltage VGHS | VPVDD = 8 to 45 V; IGATE < 30 mA; CVCPH = 2.2 uF; CCP1/CP2 = 0.047 uF; CVCP_LSD = 1 uF; TA = 25°C | min 9 · typ 10 · max 10.5 V | 7 |
| High-side gate driver Vgs voltage VGHS | VPVDD = 5.5 to 8 V; IGATE < 6 mA; CVCPH = 2.2 uF; CCP1/CP2 = 0.047 uF; CVCP_LSD = 1 uF; TA = 25°C | min 7.2 · max 9 V | 7 |
| High-side gate driver Vgs voltage VGHS | VPVDD = 4.4 to 5.5 V; IGATE < 6 mA; CVCPH = 2.2 uF; CCP1/CP2 = 0.047 uF; CVCP_LSD = 1 uF; TA = 25°C | min 5 · max 7.2 V | 7 |
| Low-side gate driver Vgs voltage VGLS | VPVDD = 8 to 45 V; IGATE < 30 mA; CVCPH = 2.2 uF; CCP1/CP2 = 0.047 uF; CVCP_LSD = 1 uF; TA = 25°C | min 9 · typ 10 · max 10.5 V | 8 |
| Low-side gate driver Vgs voltage VGLS | VPVDD = 5.5 to 8 V; IGATE < 6 mA; CVCPH = 2.2 uF; CCP1/CP2 = 0.047 uF; CVCP_LSD = 1 uF; TA = 25°C | min 9 · max 10.5 V | 8 |
| Low-side gate driver Vgs voltage VGLS | VPVDD = 4.4 to 5.5 V; IGATE < 6 mA; CVCPH = 2.2 uF; CCP1/CP2 = 0.047 uF; CVCP_LSD = 1 uF; TA = 25°C | min 8 · max 9 V | 8 |
| Peak sink or source current drive time tDRIVE | TDRIVEP = 00; TDRIVEN = 00; TA = 25°C | typ 220 ns | 8 |
| Peak sink or source current drive time tDRIVE | TDRIVEP = 01; TDRIVEN = 01; TA = 25°C | typ 440 ns | 8 |
| Peak sink or source current drive time tDRIVE | TDRIVEP = 10; TDRIVEN = 10; TA = 25°C | typ 880 ns | 8 |
| Peak sink or source current drive time tDRIVE | TDRIVEP = 11; TDRIVEN = 11; TA = 25°C | typ 1660 ns | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 0000 | typ 0.01 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 0001 | typ 0.02 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 0010 | typ 0.03 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 0011 | typ 0.04 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 0100 | typ 0.05 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 0101 | typ 0.06 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 0110 | typ 0.07 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 0111 | typ 0.125 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 1000 | typ 0.25 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 1001 | typ 0.5 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 1010 | typ 0.75 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 1011 | typ 1 A | 8 |
| High-side peak source current IDRIVEP_HS | IDRIVEP_HS = 1100, 1101, 1110, 1111 | typ 0.05 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 0000 | typ 0.02 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 0001 | typ 0.03 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 0010 | typ 0.04 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 0011 | typ 0.05 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 0100 | typ 0.06 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 0101 | typ 0.07 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 0110 | typ 0.08 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 0111 | typ 0.25 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 1000 | typ 0.5 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 1001 | typ 0.75 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 1010 | typ 1 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 1011 | typ 1.25 A | 8 |
| High-side peak sink current IDRIVEN_HS | IDRIVEN_HS = 1100, 1101, 1110, 1111 | typ 0.06 A | 8 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 0000 | typ 0.01 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 0001 | typ 0.02 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 0010 | typ 0.03 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 0011 | typ 0.04 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 0100 | typ 0.05 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 0101 | typ 0.06 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 0110 | typ 0.07 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 0111 | typ 0.125 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 1000 | typ 0.25 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 1001 | typ 0.5 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 1010 | typ 0.75 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 1011 | typ 1 A | 9 |
| Low-side peak source current IDRIVEP_LS | IDRIVEP_HS = 1100, 1101, 1110, 1111 | typ 0.05 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 0000 | typ 0.02 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 0001 | typ 0.03 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 0010 | typ 0.04 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 0011 | typ 0.05 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 0100 | typ 0.06 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 0101 | typ 0.07 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 0110 | typ 0.08 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 0111 | typ 0.25 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 1000 | typ 0.5 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 1001 | typ 0.75 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 1010 | typ 1 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 1011 | typ 1.25 A | 9 |
| Low-side peak sink current IDRIVEN_LS | IDRIVEN_HS = 1100, 1101, 1110, 1111 | typ 0.06 A | 9 |
| Gate pulldown resistance, SLEEP, undervoltage and sleep mode RSLEEP_PD | 2 V < PVDD < PVDD_UVLO2; GHX to GND; GLX to GND | typ 2000 Ω | 9 |
| Gate pulldown resistance, STANDBY, standby mode (Parallel with ISTANDBY_PD) RSTANDBY_PD | PVDD > PVDD_UVLO2; EN_GATE = low; GHX to GND; GLX to GND | typ 750 Ω | 9 |
| Gate pulldown current, OPERATING, operating mode IOPERATING_PD | PVDD > PVDD_UVLO2; EN_GATE = high; GHX to SHX; GLX to SLX | typ 50 mA | 9 |
| Gate pulldown current, holding IHOLD | PVDD > PVDD_UVLO2; EN_GATE = high; GHX to SHX; GLX to SLX | typ 50 mA | 9 |
| Gate pulldown current, strong IPULLDOWN | PVDD > PVDD_UVLO2; EN_GATE = high; GHX to SHX; GLX to SLX | typ 1.25 A | 9 |
| Positive input falling to GHS_x falling tpd_lf-O | PVDD = 12 V; CL = 1 nF; 50% to 50% | typ 200 ns | 10 |
| Positive input rising to GHS_x rising tpd_lr-O | PVDD = 12 V; CL = 1 nF; 50% to 50% | typ 200 ns | 10 |
| Minimum dead time after hand shaking td_min | typ 280 ns | 10 | |
| Dead time in addition to td_min tdtp | DEAD_TIME = 000 | typ 35 ns | 10 |
| Dead time in addition to td_min tdtp | DEAD_TIME = 001 | typ 52 ns | 10 |
| Dead time in addition to td_min tdtp | DEAD_TIME = 010 | typ 88 ns | 10 |
| Dead time in addition to td_min tdtp | DEAD_TIME = 011 | typ 440 ns | 10 |
| Dead time in addition to td_min tdtp | DEAD_TIME = 100 | typ 880 ns | 10 |
| Dead time in addition to td_min tdtp | DEAD_TIME = 101 | typ 1760 ns | 10 |
| Dead time in addition to td_min tdtp | DEAD_TIME = 110 | typ 3520 ns | 10 |
| Dead time in addition to td_min tdtp | DEAD_TIME = 111 | typ 5280 ns | 10 |
| Propagation delay matching between high-side and low-side tPD_MATCH | typ 50 ns | 10 | |
| Dead time matching tDT_MATCH | typ 50 ns | 10 | |
| Current sense amplifier gain GCSA | GAIN_CSx = 00 | typ 10 V/V | 10 |
| Current sense amplifier gain GCSA | GAIN_CSx = 01 | typ 20 V/V | 10 |
| Current sense amplifier gain GCSA | GAIN_CSx = 10 | typ 40 V/V | 10 |
| Current sense amplifier gain GCSA | GAIN_CSx = 11 | typ 80 V/V | 10 |
| Current sense amplifier gain error GERR | Input differential > 0.025 V | min -3 · max 3 % | 10 |
| Current sense amplifier settling time tSETTLING | Settling time to 1%; no blanking; TJ = -40 – 150°C, GCSA = 10; Vstep = 0.46 V | typ 300 ns | 10 |
| Current sense amplifier settling time tSETTLING | Settling time to 1%; no blanking; TJ = -40 – 150°C, GCSA = 20; Vstep = 0.46 V | typ 600 ns | 10 |
| Current sense amplifier settling time tSETTLING | Settling time to 1%; no blanking; TJ = -40 – 150°C, GCSA = 40; Vstep = 0.46 V | typ 1.2 us | 10 |
| Current sense amplifier settling time tSETTLING | Settling time to 1%; no blanking; TJ = -40 – 150°C, GCSA = 80; Vstep = 0.46 V | typ 2.4 us | 10 |
| DC input offset VIOS | GCSA = 10; input shorted; RTI | min -4 · max 4 mV | 10 |
| Reference buffer error (DC) VVREF_ERR | Internal or external VREF | min -2 · max 2 % | 10 |
| Input offset error drift VDRIFTOS | GCSA = 10; input shorted; RTI | typ 10 uV/C | 10 |
| Input bias current IBIAS | VIN_COM = 0; SOx open | max 100 uA | 10 |
| Input bias current offset IOFFSET | IBIAS (SNx-SPx); VIN_COM = 0; SOx open | typ 1 uA | 10 |
| Common input mode range VIN_COM | min -0.15 · max 0.15 V | 10 | |
| Differential input range VIN_DIFF | min -0.48 · max 0.48 V | 10 | |
| Common mode rejection ration CMRR | External input resistance matched; DC; GCSA = 10 | min 60 · typ 80 dB | 10 |
| Common mode rejection ration CMRR | External input resistance matched; 20 kHz; GCSA = 10 | min 60 · typ 80 dB | 10 |
| Power supply rejection ratio PSRR | DC (<120 Hz); GCSA = 10 | typ 150 dB | 10 |
| Power supply rejection ratio PSRR | 20 kHz; GCSA = 10 | typ 90 dB | 10 |
| Output voltage swing VSWING | PVDD > 5.3 V | min 0.3 · max 4.7 V | 10 |
| Output slew rate VSLEW | GCSA = 10; RL = 0 Ω; CL = 60 pF | min 5.2 · typ 10 V/us | 10 |
| Output short circuit current IVO | SOx shorted to ground | typ 20 mA | 11 |
| Unity gain bandwidth product UGB | GCSA = 10 | typ 2 MHz | 11 |
| AVDD undervoltage Fault VAVDD_UVLO | Relative to GND | min 3.3 · max 3.5 V | 11 |
| VREG undervoltage monitor deglitch time VVREG_UV_DGL | min 1.5 · max 2 us | 11 | |
| Undervoltage protection Warning, PVDD VPVDD_UVFL | PVDD falling | min 7.7 · max 8.1 V | 11 |
| Undervoltage protection Warning, PVDD VPVDD_UVFL | PVDD rising | min 7.9 · max 8.3 V | 11 |
| Undervoltage protection lockout, PVDD VPVDD_UVLO1 | PVDD falling | max 4.1 V | 11 |
| Undervoltage protection lockout, PVDD VPVDD_UVLO1 | PVDD rising | max 4.3 V | 11 |
| Undervoltage protection Fault, PVDD VPVDD_UVLO2 | PVDD falling | min 4.2 · max 4.4 V | 11 |
| Undervoltage protection Fault, PVDD VPVDD_UVLO2 | PVDD rising | min 4.4 · max 4.6 V | 11 |
| Overvoltage protection Warning, PVDD VPVDD_OVFL | PVDD falling | min 33.5 · max 36 V | 11 |
| Overvoltage protection Warning, PVDD VPVDD_OVFL | PVDD rising | min 32.5 · max 35 V | 11 |
| Charge pump undervoltage protection Warning, VCPH VVCPH_UVFL | Relative to PVDD | max 8 V | 11 |
| Charge pump undervoltage protection Fault, VCPH VVCPH_UVLO | Relative to PVDD, SET_VCPH_UV = 0 | min 4.5 · max 4.9 V | 11 |
| Charge pump undervoltage protection Fault, VCPH VVCPH_UVLO | Relative to PVDD, SET_VCPH_UV = 1 | min 4.2 · max 4.6 V | 11 |
| Low-side charge pump undervoltage Fault, VCP_LSD VVCP_LSD_UVLO | Relative to PVDD | min 6.4 · max 7.5 V | 11 |
| Charge pump over voltage protection FAULT, VCPH VVCPH_OVLO | Relative to PVDD | min 14 · max 18 V | 11 |
| Charge pump over voltage protection FAULT, VCPH VVCPH_OVLO_ABS | Relative to GND | typ 60 V | 11 |
| Junction temperature for resetting over temperature (OT) warning OTW_CLR | Specified by design and characterization data | typ 140 °C | 11 |
| Junction temperature for over temperature warning and resetting over temperature shutdown OTW_SET/OTSD_CLR | Specified by design and characterization data | typ 155 °C | 11 |
| Junction temperature for over temperature shutdown OTSD_SET | Specified by design and characterization data | typ 175 °C | 11 |
| Junction temperature flag setting 1 (no warning) TEMPFLAG1 | Specified by design and characterization data | typ 105 °C | 11 |
| Junction temperature flag setting 2 (no warning) TEMPFLAG2 | Specified by design and characterization data | typ 125 °C | 11 |
| Junction temperature flag setting 3 (no warning) TEMPFLAG3 | Specified by design and characterization data | typ 135 °C | 11 |
| Junction temperature flag setting 4 (no warning) TEMPFLAG4 | Specified by design and characterization data | typ 175 °C | 11 |
Pins, by the datasheet
49- 1 EN_GATE
- Enables the gate driver and current shunt amplifiers; internal pulldown. · p. 3
- 2 INHA
- PWM input signal for bridge A high side. · p. 3
- 3 INLA
- PWM input signal for bridge A low side. · p. 3
- 4 INHB
- PWM input signal for bridge B high side. · p. 3
- 5 INLB
- PWM input signal for bridge B low side. · p. 3
- 6 INHC
- PWM input signal for bridge C high side. · p. 3
- 7 INLC
- PWM input signal for bridge C low side. · p. 3
- 8 nFAULT
- Low indicates a fault; requires external 1 kΩ to 10 kΩ pullup to MCU power supply. · p. 3
- 9 nSCS
- Active-low SPI select/enable. · p. 3
- 10 SDI
- SPI input signal. · p. 3
- 11 SDO
- SPI output signal. · p. 3
- 12 SCLK
- SPI clock signal. · p. 3
- 13 PWRGD
- VREG and MCU watchdog fault indication; requires external 1 kΩ to 10 kΩ pullup to MCU power supply. · p. 3
- 14 GND
- Device ground; must be connected to ground. · p. 3
- 15 AVDD
- 5-V internal analog supply regulator; bypass to GND with a 6.3-V, 1-uF ceramic capacitor. · p. 3
- 16 SO1
- Output of current sense amplifier 1. · p. 3
- 17 SO2
- Output of current sense amplifier 2. · p. 3
- 18 SO3
- Output of current sense amplifier 3. · p. 3
- 19 SN3
- Negative input of current sense amplifier 3. · p. 3
- 20 SP3
- Positive input of current sense amplifier 3. · p. 4
- 21 SN2
- Negative input of current sense amplifier 2. · p. 4
- 22 SP2
- Positive input of current sense amplifier 2. · p. 4
- 23 SN1
- Negative input of current sense amplifier 1. · p. 4
- 24 SP1
- Positive input of current sense amplifier 1. · p. 4
- 25 GLC
- Low-side gate driver output for half-bridge C. · p. 4
- 26 SLC
- Low-side source connection for half-bridge C. · p. 4
- 27 SHC
- High-side source connection for half-bridge C. · p. 4
- 28 GHC
- High-side gate driver output for half-bridge C. · p. 4
- 29 GHB
- High-side gate driver output for half-bridge B. · p. 4
- 30 SHB
- High-side source connection for half-bridge B. · p. 4
- 31 SLB
- Low-side source connection for half-bridge B. · p. 4
- 32 GLB
- Low side gate driver output for half-bridge B. · p. 4
- 33 GLA
- Low-side gate driver output for half-bridge A. · p. 4
- 34 SLA
- Low-side source connection for half-bridge A. · p. 4
- 35 SHA
- High-side source connection for half-bridge A. · p. 4
- 36 GHA
- High-side gate driver output for half-bridge A. · p. 4
- 37 VCP_LSD
- Internal voltage regulator for low-side gate driver; connect 1-uF capacitor to GND. · p. 4
- 38 VCPH
- Internal charge pump for high-side gate driver; connect 2.2-uF capacitor to PVDD. · p. 4
- 39 CP2H
- Charge pump flying capacitor connection; connect 0.047-uF capacitor between CP2H and CP2L. · p. 4
- 40 CP2L
- Charge pump flying capacitor connection; connect 0.047-uF capacitor between CP2H and CP2L. · p. 4
- 41 PVDD
- Device power supply; minimum 4.7-uF ceramic capacitor to GND. · p. 4
- 42 CP1L
- Charge pump flying capacitor connection; connect 0.047-uF capacitor between CP1H and CP1L. · p. 4
- 43 CP1H
- Charge pump flying capacitor connection; connect 0.047-uF capacitor between CP1H and CP1L. · p. 4
- 44 VDRAIN
- High-side MOSFET drain connection; common for all three half bridges. · p. 4
- 45 GND
- Device ground; must be connected to ground. · p. 3
- 46 DVDD
- 3.3-V internal digital-supply regulator; bypass to GND with a 6.3-V, 1-uF ceramic capacitor. · p. 4
- 47 WAKE
- High voltage tolerant input to wake device from SLEEP; cannot disable LDO; driver enabled and disabled separately. · p. 4
- 48 VREG
- VREF reference-voltage input for DRV8305N, with LDO disabled; supplies internal amplifier reference voltage and SDO pullup. · p. 4
- PowerPAD PowerPAD (GND)
- Device ground; must be connected to ground. · p. 4
Open-source boards using it
3Parts like it
8DRV8305NQPHPRQ1
HTQFP-48(7x7)-40℃~+125℃ 0V~800mV 2V~5V 4.4V~45V Half-Bridge、Three Phase MOSFET Under Voltage Protection、Over Voltage Protection、Over Current Protection、Overtemperature protection (OTP) HTQFP-48(7x7) Gate Drivers ROHSTexas InstrumentsBrushless DC (BLDC) Motor DriverDRV83053QPHPRQ1
HTQFP-48(7x7)-40℃~+125℃ 0V~800mV 2V~5V 3 4.4V~45V MOSFET Three Phase Under Voltage Protection、Over Voltage Protection、Over Current Protection、Overtemperature protection (OTP) HTQFP-48(7x7) Gate Drivers ROHSTexas InstrumentsBrushless DC (BLDC) Motor DriverDRV8305NEPHPRQ1
HTQFP-48(7x7)-40℃~+150℃ 1.25A 1A 2V 4.4V~45V 6 800mV Enable shutdown、Interleaved conduction protection、Dead-time control、Overcurrent Protection、Charge pump boost MOSFET Three Phase HTQFP-48(7x7) Gate Drivers ROHSTexas InstrumentsBrushless DC (BLDC) Motor DriverDRV8305NEPHPQ1
HTQFP-48(7x7)-40℃~+150℃ 0V~800mV 2V~5V 4.4V~45V Enable shutdown、Interleaved conduction protection、Dead-time control、Overcurrent Protection、Charge pump boost MOSFET Three Phase HTQFP-48(7x7) Gate Drivers ROHSTexas InstrumentsBrushless DC (BLDC) Motor DriverDRV8305NPHP
HTQFP-48(7x7)-40℃~+125℃ 0V~800mV 2V~5V 4.4V~45V MOSFET Three Phase Under Voltage Protection、Over Voltage Protection、Overtemperature protection (OTP) HTQFP-48(7x7) Gate Drivers ROHSTexas InstrumentsBrushless DC (BLDC) Motor DriverDRV83053QPHPQ1
HTQFP-48(7x7)-40℃~+125℃ 2V 4.4V~45V 800mV MOSFET Three Phase Under Voltage Protection、Over Voltage Protection、Overtemperature protection (OTP) HTQFP-48(7x7) Gate Drivers ROHSTexas InstrumentsBrushless DC (BLDC) Motor DriverDRV8305NQPHPQ1
HTQFP-48(7x7)-40℃~+125℃ 2V 4.4V~45V 6 800mV MOSFET Three Phase Under Voltage Protection、Over Voltage Protection、Over Current Protection、Overtemperature protection (OTP) HTQFP-48(7x7) Gate Drivers ROHSTexas InstrumentsBrushless DC (BLDC) Motor DriverDRV3220QPHPRQ1
HTQFP-48(7x7)-40℃~+125℃ 3 4.75V~40V No SPI Three Phase HTQFP-48(7x7) Brushless DC (BLDC) Motor Driver ROHSTexas InstrumentsBrushless DC (BLDC) Motor Driver
Questions
Is there a KiCad symbol and footprint for the DRV8305NPHPR?
Yes. The symbol is EasyEDA_Cloud:DRV8305NPHPR and the footprint EasyEDA_Cloud:HTQFP-48_L7.0-W7.0-P0.50-LS9.0-BL-EP5.1, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the DRV8305NPHPR?
HTQFP-48(7x7), with 49 pins. Its footprint is drawn on this page.
Where is the DRV8305NPHPR datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the DRV8305NPHPR?
JLCPCB lists it as part C75602, with 489 in stock; the sellers' links on this page open their listings.
What can replace the DRV8305NPHPR?
Parts like it in the library: the DRV8305NQPHPRQ1 by Texas Instruments, the DRV83053QPHPRQ1 by Texas Instruments, the DRV8305NEPHPRQ1 by Texas Instruments and the DRV8305NEPHPQ1 by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the DRV8305NPHPR?
3 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.

