Skip to the content
57

DRV8302DCAR

Texas InstrumentsExtended

-40℃~+125℃ 2.3A 3 50uA 8V~60V Three Phase HTSSOP-56-6mm Brushless DC (BLDC) Motor Driver ROHS

Part id
ti/DRV8302DCAR
Category
Brushless DC (BLDC) Motor Driver
Package
HTSSOP-56-6mm
Pins
56
In stock
2,496 at JLCPCB (C79740)
Used on
4 open-source boards

Overview

The DRV8302DCAR is a brushless DC (BLDC) Motor Driver made by Texas Instruments in a HTSSOP-56-6mm package with 57 pins. -40℃~+125℃ 2.3A 3 50uA 8V~60V Three Phase HTSSOP-56-6mm Brushless DC (BLDC) Motor Driver ROHS.

PCBKit's library has its KiCad symbol (Celestial_Driver_Motor:TI DRV8302, from Altium's library) and its footprint (EasyEDA_Cloud:HTSSOP-56_L14.0-W6.1-P0.50-LS8.1-BL-EP, from EasyEDA), ready for a KiCad board. 2,496 are in stock at JLCPCB (part C79740). 4 open-source boards in 3 repositories on GitHub use it.

Symbol

1RT_CLK2COMP3VSENSE4PWRGD5OCTW6FAULT7DTC8M_PWM9M_OC10GAIN11OC_ADJ12DC_CAL13GVDD14CP115CP216EN_GATE23DVDD24REF25SO126SO227AVDD28AGND29PVDD130SP231SN232SP133SN149BIAS50PH51PH52BST_BK53PVDD254PVDD255EN_BUCK56SS_TR57GND
Celestial_Driver_Motor:TI DRV8302From Altium's library

Footprint

57
EasyEDA_Cloud:HTSSOP-56_L14.0-W6.1-P0.50-LS8.1-BL-EPFrom EasyEDA

From the datasheet

19
Supply, least
8 V · PVDD1, recommended operating min · p. 6
Supply, most
60 V · PVDD1, recommended operating max · p. 6
Supply, least
3.5 V · PVDD2, recommended operating min · p. 6
Supply, absolute maximum
65 V · PVDD, absolute max relative to PGND · p. 5
Works from
-40 °C · Ambient temperature min · p. 6
Works up to
125 °C · Ambient temperature max · p. 6
Junction, hottest
150 °C · Operating junction temperature max · p. 5
Takes working
15.12 mA · sum of typical PVDD1 operating and PVDD2 nonswitching currents · p. 7
Takes asleep
20 µA · PVDD1 standby typical, EN_GATE low, PVDD1 = 8 V · p. 7
Takes asleep
1.3 µA · PVDD2 shutdown typical, EN = 0 V, 25°C · p. 9
Gives
1.5 A · Buck converter rated output max · p. 1
Current limit
2.7 A · Buck current limit typical, VIN = 12 V, TJ = 25°C · p. 9
A pin gives at most
7 mA · nFAULT and nOCTW sinking current absolute max · p. 5
Switches at
581 kHz · Buck switching frequency typical, RT = 200 kΩ · p. 9
Junction to air (DCA (HTSSOP))
30.3 K/W · Junction-to-ambient thermal resistance · p. 6
Junction to case (DCA (HTSSOP))
33.5 K/W · Junction-to-case top thermal resistance · p. 6
Junction to board (DCA (HTSSOP))
17.5 K/W · Junction-to-board thermal resistance · p. 6
Edge
25 ns · Gate output rise time typical, CL = 1 nF, 10% to 90% · p. 8
Feedback reference
800 mV · buck regulator feedback reference · p. 15

What it is and has

18
Gate drive current
1.7-A source and 2.3-A sink · p. 1
Gate driver
Bootstrap, 100% duty cycle support · p. 1
PWM input modes
6 or 3 PWM inputs · p. 1
Current shunt amplifiers
Dual integrated, adjustable gain and offset · p. 1
Interface voltage
3.3 V and 5 V · p. 1
Control interface
Hardware · p. 1
Protection
Programmable dead time control · p. 1
Protection
Programmable overcurrent protection · p. 1
Protection
PVDD and GVDD undervoltage lockout · p. 1
Protection
GVDD overvoltage lockout · p. 1
Protection
Overtemperature warning and shutdown · p. 1
Fault reporting
nFAULT and nOCTW pins · p. 1
Package
HTSSOP (56), 14.00 mm × 6.10 mm · p. 1
Gate drivers
Three half-bridges, each driving two N-channel MOSFETs · p. 13
PWM control
6-PWM or 3-PWM · p. 13
Current shunt amplifiers
Two bidirectional low-side amplifiers · p. 22
Buck converter
Integrated TPS54160, 1.5 A, 60 V · p. 15
Bootstrap operation
100% duty cycle support with trickle charge pump · p. 13

Around it

13
res 1M-Ω
between BIAS and GND; Alternative to a 0.1 uF capacitor. · p. 4
cap 0.1 µF
between BIAS and GND; Alternative to a 1M-Ω resistor. · p. 4
res ≥10 kΩ
between nOCTW and VCC; Pull-up to the MCU logic supply. · p. 13
res ≥10 kΩ
between nFAULT and VCC; Pull-up to the MCU logic supply. · p. 13
res 0 to 150 kΩ
between DTC and GND (PowerPAD); Sets dead time from 50 ns to 500 ns. · p. 13
cap 2.2 µF
between GVDD and GND (PowerPAD); 20% ceramic, rated ≥16 V. · p. 13
cap 0.022 µF
between CP1 and CP2; 20% ceramic, rated for PVDD1. · p. 13
cap 1 µF
between DVDD and AGND; 20% ceramic, rated ≥6.3 V. · p. 13
cap 1 µF
between AVDD and AGND; 20% ceramic, rated ≥10 V. · p. 13
cap ≥4.7 µF
between PVDD1 and GND (PowerPAD); 20% ceramic, rated for PVDD1. · p. 13
cap 0.1 µF
between BST_X and SH_X; For each half-bridge; 20% ceramic, rated ≥16 V. · p. 13
res ≥ 10 kΩ
between PWRGD and VCC; Pull-up to the MCU logic supply. · p. 16
cap ≥4.7 µF
between PVDD2 and GND (PowerPAD); 20% ceramic, rated for PVDD2. · p. 16

Specifications

102
ParameterConditionsAs printedPage
Supply voltage VPVDDRelative to PGNDmin -0.3 · max 65 V5
Maximum supply voltage ramp rate PVDDRAMPVoltage rising up to PVDDMAXmax 1 V/us5
Maximum voltage between PGND and GND VPGNDmin -0.3 · max 0.3 V5
Maximum current, all digital and analog input pins except nFAULT and nOCTW pins IIN_MAXmin -1 · max 1 mA5
Maximum sinking current for open-drain pins (nFAULT and nOCTW Pins) IIN_OD_MAXmax 7 mA5
Voltage range for SPx and SNx pins VOPA_INmin -0.6 · max 0.6 V5
Input voltage range for logic/digital pins (INH_A, INL_A, INH_B, INL_B, INH_C, INL_C, EN_GATE, M_PWM, M_OC, OC_ADJ, GAIN, DC_CAL) VLOGICmin -0.3 · max 7 V5
Maximum voltage for GVDD pin VGVDDmax 13.2 V5
Maximum voltage for AVDD pin VAVDDmax 8 V5
Maximum voltage for DVDD pin VDVDDmax 3.6 V5
Maximum reference voltage for current amplifier VREFmax 7 V5
Maximum current for REF Pin IREFmax 100 uA5
Maximum operating junction temperature TJmin -40 · max 150 °C5
Storage temperature Tstgmin -55 · max 150 °C5
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001min -2000 · max 2000 V5
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101min -500 · max 500 V5
DC supply voltage PVDD1 for normal operation VPVDDRelative to PGNDmin 8 · max 60 V6
DC supply voltage PVDD2 for buck converter VPVDDmin 3.5 · max 60 V6
Input current of digital pins when EN_GATE is high IDIN_ENmax 100 uA6
Input current of digital pins when EN_GATE is low IDIN_DISmax 1 uA6
Maximum output capacitance on outputs of shunt amplifier CO_OPAmax 20 pF6
Dead time control resistor range. Time range is 50 ns (–GND) to 500 ns (150 kΩ) with a linear approximation. RDTCmin 0 · max 150 kΩ6
FAULT pin sink current. Open drain IFAULTV = 0.4 Vmax 2 mA6
OCTW pin sink current. Open drain IOCTWV = 0.4 Vmax 2 mA6
External voltage reference voltage for current shunt amplifiers VREFmin 2 · max 6 V6
Operating switching frequency of gate driver fgateQg(TOT) = 25 nC or total 30-mA gate drive average currentmax 200 kHz6
Ambient temperature TAmin -40 · max 125 °C6
Junction-to-ambient thermal resistance RθJADCA (HTSSOP), 56 PINStyp 30.3 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)DCA (HTSSOP), 56 PINStyp 33.5 °C/W6
Junction-to-board thermal resistance RθJBDCA (HTSSOP), 56 PINStyp 17.5 °C/W6
Junction-to-top characterization parameter ψJTDCA (HTSSOP), 56 PINStyp 0.9 °C/W6
Junction-to-board characterization parameter ψJBDCA (HTSSOP), 56 PINStyp 7.2 °C/W6
Junction-to-case (bottom) thermal resistance RθJC(bot)DCA (HTSSOP), 56 PINStyp 0.9 °C/W6
High input threshold VIHINH_X, INL_X, M_PWM, M_OC, GAIN, EN_GATE, DC_CAL; PVDD = 8 V to 60 V, TC = 25°Cmin 2 V7
Low input threshold VILINH_X, INL_X, M_PWM, M_OC, GAIN, EN_GATE, DC_CAL; PVDD = 8 V to 60 V, TC = 25°Cmax 0.8 V7
Internal pulldown resistor for EN_GATE REN_GATEPVDD = 8 V to 60 V, TC = 25°Ctyp 100 kΩ7
Internal pulldown resistor for high side PWMs (INH_A, INH_B, and INH_C) RINH_XEN_GATE high; PVDD = 8 V to 60 V, TC = 25°Ctyp 100 kΩ7
Internal pulldown resistor for low side PWMs (INL_A, INL_B, and INL_C) RINH_XEN_GATE high; PVDD = 8 V to 60 V, TC = 25°Ctyp 100 kΩ7
Internal pulldown resistor for M_PWM RM_PWMEN_GATE high; PVDD = 8 V to 60 V, TC = 25°Ctyp 100 kΩ7
Internal pulldown resistor for M_OC RM_OCEN_GATE high; PVDD = 8 V to 60 V, TC = 25°Ctyp 100 kΩ7
Internal pulldown resistor for DC_CAL RDC_CALEN_GATE high; PVDD = 8 V to 60 V, TC = 25°Ctyp 100 kΩ7
Low output threshold VOLnFAULT and nOCTW; IO = 2 mA; PVDD = 8 V to 60 V, TC = 25°Cmax 0.4 V7
High output threshold VOHnFAULT and nOCTW; external 47-kΩ pullup resistor connected to 3-5.5 V; PVDD = 8 V to 60 V, TC = 25°Cmin 2.4 V7
Leakage current on open-drain pins When logic high (nFAULT and nOCTW) IOHPVDD = 8 V to 60 V, TC = 25°Cmax 1 uA7
Gate driver Vgs voltage VGX_NORMPVDD = 8 V to 60 V, TC = 25°Cmin 9.5 · max 11.5 V7
Maximum source current setting 1, peak Ioso1Vgs of FET equals to 2 V; PVDD = 8 V to 60 V, TC = 25°Ctyp 1.7 A7
Maximum sink current setting 1, peak Iosi1Vgs of FET equals to 8 V; PVDD = 8 V to 60 V, TC = 25°Ctyp 2.3 A7
Gate output impedance during standby mode when EN_GATE low (pins GH_x, GL_x) Rgate_offPVDD = 8 V to 60 V, TC = 25°Cmin 1.6 · max 2.4 kΩ7
PVDD1 supply current, standby IPVDD1_STBEN_GATE is low. PVDD1 = 8 V.; TC = 25°Ctyp 20 · max 50 uA7
PVDD1 supply current, operating IPVDD1_OPEN_GATE is high, no load on gate drive output, switching at 10 kHz, 100-nC gate charge; PVDD = 8 V to 60 V, TC = 25°Ctyp 15 mA7
PVDD1 Supply current, HiZ IPVDD1_HIZEN_GATE is high, gate not switching; PVDD = 8 V to 60 V, TC = 25°Cmin 2 · typ 5 · max 11 mA7
AVDD voltage AVDDPVDD = 8 V to 60 V, TC = 25°Cmin 6 · typ 6.5 · max 7 V7
DVDD voltage DVDDPVDD = 8 V to 60 V, TC = 25°Cmin 3 · typ 3.3 · max 3.6 V7
Undervoltage protection limit, PVDD VPVDD_UVPVDD = 8 V to 60 V, TC = 25°Cmax 6 V7
Undervoltage protection limit, GVDD VGVDD_UVPVDD = 8 V to 60 V, TC = 25°Cmax 8 V7
Overvoltage protection limit, GVDD VGVDD_OVPVDD = 8 V to 60 V, TC = 25°Ctyp 16 V7
Drain-source voltage protection limit VDS_OCPVDD = 8 V to 60 V, TC = 25°Cmin 0.125 · max 2.4 V7
OC sensing response time TocPVDD = 8 V to 60 V, TC = 25°Ctyp 1.5 us7
OCTW pin reporting pulse stretch length for OC event TOC_PULSEPVDD = 8 V to 60 V, TC = 25°Ctyp 64 us7
Positive input falling to GH_x falling tpd,If-OCL=1 nF, 50% to 50%typ 45 ns8
Positive input rising to GL_x falling tpd,Ir-OCL=1 nF, 50% to 50%typ 45 ns8
Minimum dead time after hand shaking Td_minmax 50 ns8
Dead Time TdtpWith RDTC set to different valuesmin 50 · max 500 ns8
Rise time, gate drive output tGDrCL=1 nF, 10% to 90%typ 25 ns8
Fall time, gate drive output tGDFCL=1 nF, 90% to 10%typ 25 ns8
Minimum on pulse TON_MINNot including handshake communication. Hiz to on state, output of gate drivermax 50 ns8
Propagation delay matching between high side and low side Tpd_matchmax 5 ns8
Deadtime matching Tdt_matchmax 5 ns8
Start-up time, from EN_GATE active high to device ready for normal operation tpd,R_GATE-OPPVDD is up before start-up, all charge pump caps and regulator caps as in recommended conditiontyp 5 · max 10 ms8
If EN_GATE goes from high to low and back to high state within quick reset time, it will only reset all faults and gate driver without powering down charge pump, current amp, and related internal voltage regulators. tpd,R_GATE-QuickMaximum low pulse timemax 10 us8
Delay, error event to all gates low tpd,E-Ltyp 200 ns8
Delay, error event to FAULT low tpd,E-FAULTtyp 200 ns8
Junction temperature for resetting overtemperature warning OTW_CLRtyp 115 °C8
Junction temperature for overtemperature warning and resetting overtemperature shut down OTW_SET/OTSD_CLRtyp 130 °C8
Junction temperature for overtemperature shut down OTSD_SETtyp 150 °C8
Gain option 1 G1(GAIN = 0 V); TC = 25°Cmin 9.5 · typ 10 · max 10.5 V/V8
Gain option 2 G2(GAIN = 2 V); TC = 25°Cmin 38 · typ 40 · max 42 V/V8
Settling time to 1% TsettlingTc = 0°C to 60°C, G = 10, Vstep = 2 Vtyp 300 ns8
Settling time to 1% TsettlingTc = 0°C to 60°C, G = 40, Vstep = 2 Vtyp 1.2 us8
Output swing linear range VswingTC = 25°Cmin 0.3 · max 5.7 V8
Slew RateG = 10; TC = 25°Ctyp 10 V/us8
Offset error RTI DC_offsetG = 10 with input shorted; TC = 25°Cmax 4 mV8
Offset drift RTI Drift_offsetTC = 25°Ctyp 10 uV/C8
Input bias current IbiasTC = 25°Cmax 100 uA8
Common input mode range Vin_comTC = 25°Cmin -0.15 · max 0.15 V8
Differential input range Vin_difTC = 25°Cmin -0.3 · max 0.3 V8
Overall CMRR with gain resistor mismatch CMRR_OVCMRR at DC, gain = 10; TC = 25°Cmin 70 · typ 85 dB8
Internal undervoltage lockout threshold VUVLONo voltage hysteresis, rising and falling; TC = 25°Ctyp 2.5 V9
Shutdown supply current ISD(PVDD2)EN = 0 V, 25°C, 3.5 V ≤ VIN ≤ 60 Vtyp 1.3 · max 4 uA9
Operating: nonswitching supply current INON_SW(PVDD2)VSENSE = 0.83 V, VIN = 12 V; TC = 25°Ctyp 116 · max 136 uA9
Enable threshold voltage VEN_BUCKNo voltage hysteresis, rising and falling; TC = 25°Cmin 1.11 · typ 1.25 · max 1.36 V9
On-resistance RDS_ONVIN = 12 V, BOOT-PH = 6 V; TC = 25°Ctyp 200 · max 410 mΩ9
Current limit threshold ILIMVIN = 12 V, TJ = 25°Cmin 1.8 · typ 2.7 A9
Thermal shutdown OTSD_BKTC = 25°Ctyp 150 °C9
Switching frequency FswRT = 200 kΩ; TC = 25°Cmin 450 · typ 581 · max 720 kHz9
VSENSE threshold PWRGDVSENSE falling; lower threshold; TC = 25°Ctyp 92 %9
VSENSE threshold PWRGDVSENSE rising; lower threshold; TC = 25°Ctyp 94 %9
VSENSE threshold PWRGDVSENSE rising; upper threshold; TC = 25°Ctyp 109 %9
VSENSE threshold PWRGDVSENSE falling; upper threshold; TC = 25°Ctyp 107 %9
HysteresisVSENSE falling; TC = 25°Ctyp 2 %9
Output high leakageVSENSE = VREF, V(PWRGD) = 5.5 V, 25°Ctyp 10 nA9
On resistanceI(PWRGD) = 3 mA, VSENSE < 0.79 V; TC = 25°Ctyp 50 Ω9

Pins, by the datasheet

57
1 RT_CLK
Buck timing resistor and external clock; connect resistor to GND (PowerPAD) with a very short trace. · p. 3
2 COMP
Buck error amplifier output and input to the output switch current comparator. · p. 3
3 VSENSE
Buck output voltage sense; inverting node of error amplifier. · p. 3
4 PWRGD
Requires external pullup; asserts low for low buck output due to thermal shutdown, dropout, overvoltage, or EN_BUCK shutdown. · p. 3
5 nOCTW
Overcurrent and overtemperature warning indicator; requires external pullup resistor. · p. 3
6 nFAULT
Fault report indicator; requires external pullup resistor. · p. 3
7 DTC
Dead-time adjustment with external resistor to GND. · p. 3
8 M_PWM
Low selects six independent PWM inputs; high selects three PWM inputs on INH_x with complementary low-side signals generated internally. · p. 3
9 M_OC
Low selects cycle-by-cycle current limiting; high shuts down the channel detecting overcurrent. · p. 3
10 GAIN
Selects current shunt amplifier gain: low gives 10 V/V and high gives 40 V/V. · p. 3
11 OC_ADJ
Applied voltage sets overcurrent trip point; voltage divider from DVDD recommended. · p. 3
12 DC_CAL
High shorts shunt amplifier inputs and disconnects loads for DC offset calibration by an external microcontroller. · p. 3
13 GVDD
Internal gate driver voltage regulator; connect capacitor to GND. · p. 4
14 CP1
Charge pump pin 1; use ceramic capacitor between CP1 and CP2. · p. 4
15 CP2
Charge pump pin 2; use ceramic capacitor between CP1 and CP2. · p. 4
16 EN_GATE
Enables gate driver and current shunt amplifiers; buck is controlled through EN_BUCK. · p. 4
17 INH_A
High-side PWM input, half-bridge A. · p. 4
18 INL_A
Low-side PWM input, half-bridge A. · p. 4
19 INH_B
High-side PWM input, half-bridge B. · p. 4
20 INL_B
Low-side PWM input, half-bridge B. · p. 4
21 INH_C
High-side PWM input, half-bridge C. · p. 4
22 INL_C
Low-side PWM input, half-bridge C. · p. 4
23 DVDD
Internal 3.3-V supply; connect capacitor to AGND; not specified to drive external circuitry. · p. 4
24 REF
Sets shunt amplifier output bias to half the applied voltage; connect to microcontroller ADC reference. · p. 4
25 SO1
Output of current amplifier 1. · p. 4
26 SO2
Output of current amplifier 2. · p. 4
27 AVDD
Internal 6-V supply; connect capacitor to AGND; not specified to drive external circuitry. · p. 4
28 AGND
Analog ground. · p. 4
29 PVDD1
Gate driver and current shunt amplifier supply, independent of PVDD2; connect capacitor to GND. · p. 4
30 SP2
Positive input of current amplifier 2; connect to ground side of sense resistor for best common-mode rejection. · p. 4
31 SN2
Negative input of current amplifier 2. · p. 4
32 SP1
Positive input of current amplifier 1; connect to ground side of sense resistor for best common-mode rejection. · p. 4
33 SN1
Negative input of current amplifier 1. · p. 4
34 SL_C
Low-side MOSFET source connection, half-bridge C; low-side VDS measured to SH_C. · p. 4
35 GL_C
Low-side MOSFET gate drive, half-bridge C. · p. 4
36 SH_C
High-side MOSFET source connection, half-bridge C; high-side VDS measured to PVDD1. · p. 4
37 GH_C
High-side MOSFET gate drive, half-bridge C. · p. 4
38 BST_C
Bootstrap capacitor pin for half-bridge C. · p. 4
39 SL_B
Low-side MOSFET source connection, half-bridge B; low-side VDS measured to SH_B. · p. 4
40 GL_B
Low-side MOSFET gate drive, half-bridge B. · p. 4
41 SH_B
High-side MOSFET source connection, half-bridge B; high-side VDS measured to PVDD1. · p. 4
42 GH_B
High-side MOSFET gate drive, half-bridge B. · p. 4
43 BST_B
Bootstrap capacitor pin for half-bridge B. · p. 4
44 SL_A
Low-side MOSFET source connection, half-bridge A; low-side VDS measured to SH_A. · p. 4
45 GL_A
Low-side MOSFET gate drive, half-bridge A. · p. 4
46 SH_A
High-side MOSFET source connection, half-bridge A; high-side VDS measured to PVDD1. · p. 4
47 GH_A
High-side MOSFET gate drive, half-bridge A. · p. 4
48 BST_A
Bootstrap capacitor pin for half-bridge A. · p. 4
49 BIAS
Connect 1M-Ω resistor or 0.1 uF capacitor to GND. · p. 4
50 PH
Source of the buck converter internal high-side MOSFET. · p. 4
51 PH
Source of the buck converter internal high-side MOSFET. · p. 4
52 BST_BK
Bootstrap capacitor pin for buck converter. · p. 5
53 PVDD2
Buck converter supply; connect capacitor to GND. · p. 5
54 PVDD2
Buck converter supply; connect capacitor to GND. · p. 5
55 EN_BUCK
Buck enable with internal pullup current source; pull below 1.2 V to disable or float to enable; two resistors adjust input undervoltage lockout. · p. 5
56 SS_TR
Buck soft-start and tracking; external capacitor to GND sets output rise time; supports tracking and sequencing. · p. 5
57 GND (PWR_PAD)
Solder exposed pad to ground plane and connect through vias to the PCB bottom side for thermal spreading. · p. 12

Ordering codes, by the datasheet

6
DRV8302DCA
HTSSOP (DCA), 56 pins · 35 per tube; operating temperature -40 to 125 °C · p. 27
DRV8302DCA.A
HTSSOP (DCA), 56 pins · 35 per tube; operating temperature -40 to 125 °C · p. 27
DRV8302DCAG4
HTSSOP (DCA), 56 pins · 35 per tube; operating temperature -40 to 125 °C · p. 27
DRV8302DCAG4.A
HTSSOP (DCA), 56 pins · 35 per tube; operating temperature -40 to 125 °C · p. 27
DRV8302DCAR
HTSSOP (DCA), 56 pins · 2000 per large tape and reel; operating temperature -40 to 125 °C · p. 27
DRV8302DCAR.A
HTSSOP (DCA), 56 pins · 2000 per large tape and reel; operating temperature -40 to 125 °C · p. 27

Open-source boards using it

4
  • 4 layers52.8 × 56.4 mmESP32 Motor Controller, the printed circuit board in 3D

    ESP32 Motor Controller

    Angelpele/Integrated_FOC_BLDC_Actuator

    Design and development of a portable, self contained closed loop Field Oriented Controller (FOC) for Brushless DC (BLDC) motors built on the ESP32 S3 via a custom designed PCB.

    154 partsMIT
  • 4 layers100 × 75 mmDF ESC rev01 1, the printed circuit board in 3D

    DF ESC rev01 1

    ivanmendezalonso/KICAD_repo

    Aqui estaran todos las carpetas de proyectos

    194 parts
  • 4 layers113 × 100.2 mmSTM32 - BLDC Driver, the printed circuit board in 3D

    STM32 - BLDC Driver

    FredrikLLarsen/STM32F411_DRV8302_FOC_PCBA

    162 parts

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the DRV8302DCAR?

Yes. The symbol is Celestial_Driver_Motor:TI DRV8302 and the footprint EasyEDA_Cloud:HTSSOP-56_L14.0-W6.1-P0.50-LS8.1-BL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DRV8302DCAR?

HTSSOP-56-6mm, with 57 pins. Its footprint is drawn on this page.

Where is the DRV8302DCAR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the DRV8302DCAR?

JLCPCB lists it as part C79740, with 2,496 in stock; the sellers' links on this page open their listings.

What can replace the DRV8302DCAR?

Parts like it in the library: the FAN8741MTFX by onsemi. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the DRV8302DCAR?

4 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.