Skip to the content
25

BQ25896RTW

Texas InstrumentsExtended

-40℃~+85℃ 1 12uA 3.9V~14V 3A 4.208V Charging IC I2C Support QFN-24-EP(4x4) Battery Management ROHS

Part id
ti/BQ25896RTW
Category
Battery Management
Package
QFN-24-EP(4x4)
Pins
25
In stock
766 at JLCPCB (C181475)
Used on
2 open-source boards

Overview

The BQ25896RTW is a battery Management made by Texas Instruments in a QFN-24-EP(4x4) package with 25 pins. -40℃~+85℃ 1 12uA 3.9V~14V 3A 4.208V Charging IC I2C Support QFN-24-EP(4x4) Battery Management ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:BQ25896RTWR, from EasyEDA) and its footprint (EasyEDA_Cloud:VQFN-24_L4.0-W4.0-P0.50-TL-EP2.7, from EasyEDA), ready for a KiCad board. 766 are in stock at JLCPCB (part C181475). 2 open-source boards in 2 repositories on GitHub use it.

Symbol

1VBUS2PSEL3PG4STAT5SCL6SDA7INT8OTG9CE10LIIM11TS12QON13BAT14BAT15SYS16SYS17PGND18PGND19SW20SW21BTST22REGN23PMID24NC25EPAD
EasyEDA_Cloud:BQ25896RTWRFrom EasyEDA

Footprint

25
EasyEDA_Cloud:VQFN-24_L4.0-W4.0-P0.50-TL-EP2.7From EasyEDA

From the datasheet

15
Supply, least
3.9 V · VBUS, recommended operating min · p. 7
Supply, most
14 V · VBUS, recommended operating max · p. 7
Supply, absolute maximum
22 V · VBUS, converter not switching, absolute max · p. 7
Works from
-40 °C · Operating free-air temperature min · p. 7
Works up to
85 °C · Operating free-air temperature max · p. 7
Junction, hottest
150 °C · Junction temperature absolute max · p. 7
Takes working
3 mA · VBUS buck mode switching, VBAT = 3.2 V, ISYS = 0 A, typical · p. 8
Takes asleep
12 µA · Battery ship mode, BATFET and battery monitor disabled, typical · p. 8
Gives
3 A · Fast charging current max · p. 7
A pin gives at most
6 mA · INT and STAT output sink current absolute max · p. 7
Switches at
1.5 MHz · Charge mode frequency typical · p. 4
Junction to air (RTW (WQFN))
31.8 K/W · Junction-to-ambient thermal resistance · p. 8
Junction to case (RTW (WQFN))
27.9 K/W · Junction-to-case top thermal resistance · p. 8
Junction to board (RTW (WQFN))
8.7 K/W · Junction-to-board thermal resistance · p. 8
Gives
2 A · maximum boost mode output current · p. 10

What it is and has

18
Battery chemistry
Single-cell Li-Ion and Li-polymer · p. 3
ADC
7-bit; monitors charge current and VBUS, BAT, SYS, TS voltages · p. 3
I2C address
6BH (1101011B + R/W) · p. 4
Charge mode frequency
1.5 MHz · p. 4
Boost mode frequency
1.5 MHz default or 500 KHz · p. 4
Default battery charge voltage
4.208 V · p. 4
Maximum charge current
3.008A · p. 4
Default charge current
2.048 A · p. 4
Maximum boost mode output current
2A · p. 4
Charging temperature profile
JEITA · p. 4
Package
24-pin, 4 x 4 mm2 x 0.75 mm thin WQFN · p. 3
Protection
Battery temperature monitoring, charging safety timer, overvoltage and overcurrent protection · p. 3
Thermal protection
Thermal regulation and thermal shutdown · p. 1
Charger
I2C controlled single-cell 3-A fast charger with MaxCharge technology · p. 1
Charge voltage regulation accuracy
±0.5% · p. 1
Charge current regulation accuracy
±5% · p. 1
Input current regulation accuracy
±7.5% · p. 1
Integrated bootstrap diode
High-side gate drive · p. 49

Around it

14
cap 1-µF
between VBUS and PGND; Ceramic; place as close as possible to IC. · p. 5
res 10-kΩ
between PG and pull up rail; Power good output pull-up. · p. 5
res 10-kΩ
between STAT and pull up rail; Charge status output pull-up. · p. 5
res 10-kΩ
between SCL and logic rail; I2C clock pull-up. · p. 5
res 10-kΩ
between SDA and logic rail; I2C data pull-up. · p. 5
res 10-kΩ
between INT and logic rail; Interrupt output pull-up. · p. 5
other 103AT-2
between TS and GND; Recommended NTC thermistor in temperature qualification divider from REGN through TS to GND. · p. 6
cap 10uF
between BAT and GND; Place close to BAT pin. · p. 6
cap 20uF
between SYS and GND; Place close to SYS pin. · p. 6
cap 0.047µF
between SW and BTST; Bootstrap capacitor. · p. 6
cap 4.7 µF
between REGN and GND; 10 V rating, ceramic, analog ground; place close to IC. · p. 6
res 260-Ω
between ILIM and ground; Example hardware input current limit of 1.5 A using KILIM = 390 maximum. · p. 26
cap 8.2 μF
between PMID and GND; Input decoupling; X7R or X5R ceramic preferred, rated 25 V or higher for input up to 14 V. Place close to PMID and GND. · p. 50
res 0Ω
between analog ground and power ground; Alternative connection between analog and power ground. · p. 55

Specifications

156
ParameterConditionsAs printedPage
Voltage range (with respect to GND)VBUS (converter not switching)min -2 · max 22 V7
Voltage range (with respect to GND)PMID (converter not switching)min -0.3 · max 22 V7
Voltage range (with respect to GND)STATmin -0.3 · max 20 V7
Voltage range (with respect to GND)PGmin -0.3 · max 7 V7
Voltage range (with respect to GND)BTSTmin -0.3 · max 20 V7
Voltage range (with respect to GND)SWmin -2 · max 16 V7
Voltage range (with respect to GND)SW (peak for 10 ns duration)min -3 · max 16 V7
Voltage range (with respect to GND)BAT, SYS (converter not switching)min -0.3 · max 6 V7
Voltage range (with respect to GND)SDA, SCL, INT, OTG, REGN, TS, CE, QONmin -0.3 · max 7 V7
Voltage range (with respect to GND)PSELmin -0.3 · max 7 V7
Voltage range (with respect to GND)BTST TO SWmin -0.3 · max 7 V7
Voltage range (with respect to GND)PGND to GNDmin -0.3 · max 0.3 V7
Voltage range (with respect to GND)ILIMmin -0.3 · max 5 V7
Output sink currentINT, STATmax 6 mA7
Output sink currentPGmax 6 mA7
Junction temperaturemin -40 · max 150 °C7
Storage temperature range Tstgmin -65 · max 150 °C7
Electrostatic discharge VESDHuman body model (HBM), per ANSI/ESDA/JEDEC JS-001min -2000 · max 2000 V7
Electrostatic discharge VESDCharged device model (CDM), per JEDEC specification JESD22-C101min -250 · max 250 V7
Input voltage VINmin 3.9 · max 14 V7
Input current (VBUS) IINmax 3.25 A7
Output current (SW) ISYSmax 5 A7
Battery voltage VBATmax 4.608 V7
Fast charging current IBATmax 3 A7
Discharging current with internal MOSFET IBATContinuousmax 6 A7
Discharging current with internal MOSFET IBATPeak, up to 1 sec durationmax 9 A7
Operating free-air temperature range TAmin -40 · max 85 °C7
Junction-to-ambient thermal resistance RθJARTW (WQFN), 24-PINStyp 31.8 °C/W8
Junction-to-case (top) thermal resistance RθJC((op)RTW (WQFN), 24-PINStyp 27.9 °C/W8
Junction-to-board thermal resistance RθJBRTW (WQFN), 24-PINStyp 8.7 °C/W8
Junction-to-top characterization parameter ψJTRTW (WQFN), 24-PINStyp 0.3 °C/W8
Junction-to-board characterization parameter ψJBRTW (WQFN), 24-PINStyp 8.7 °C/W8
Junction-to-case (bottom) thermal resistance RθJC(bot)RTW (WQFN), 24-PINStyp 2 °C/W8
Battery discharge current (BAT, SW, SYS) in buck mode IBATVBAT = 4.2 V, V(VBUS) < V(UVLO), leakage between BAT and VBUSmax 5 uA8
Battery discharge current (BAT, SW, SYS) in buck mode IBATHigh-Z mode, no VBUS, BATFET disabled (REG09[5]=1), battery monitor disabled, TJ < 85°Ctyp 12 · max 23 uA8
Battery discharge current (BAT, SW, SYS) in buck mode IBATHigh-Z mode, no VBUS, BATFET enabled (REG09[5]=0), battery monitor disabled, TJ < 85°Ctyp 32 · max 60 uA8
Input supply current (VBUS) in buck mode when High-Z mode is enabled I(VBUS_HIZ)V(VBUS)= 5 V, High-Z mode, no battery, battery monitor disabledtyp 15 · max 35 uA8
Input supply current (VBUS) in buck mode when High-Z mode is enabled I(VBUS_HIZ)V(VBUS)= 12 V, High-Z mode, no battery, battery monitor disabledtyp 25 · max 50 uA8
Input supply current (VBUS) in buck mode I(VBUS)VBUS > V(UVLO), VBUS > VBAT, converter not switchingtyp 1.5 · max 3 mA8
Input supply current (VBUS) in buck mode I(VBUS)VBUS > V(UVLO), VBUS > VBAT, converter switching, VBAT = 3.2 V, ISYS = 0Atyp 3 mA8
Input supply current (VBUS) in buck mode I(VBUS)VBUS > V(UVLO), VBUS > VBAT, converter switching, VBAT = 3.8 V, ISYS = 0 Atyp 3 mA8
Battery discharge current in boost mode I(BOOST)VBAT = 4.2 V, boost mode, I(VBUS)= 0 A, converter switchingtyp 5 mA8
VBUS operating range V(VBUS_OP)min 3.9 · max 14 V8
VBUS for active I2C, no battery V(VBUS_UVLOZ)min 3.6 V8
Sleep mode falling threshold V(SLEEP)min 25 · typ 65 · max 120 mV8
Sleep mode rising threshold V(SLEEPZ)min 130 · typ 250 · max 370 mV8
VBUS over-voltage rising threshold V(ACOV)min 14 · max 14.6 V8
VBUS over-voltage falling threshold V(ACOV)min 13.5 · max 14 V8
Battery for active I2C, no VBUS VBAT(UVLOZ)min 2.3 V8
Battery depletion falling threshold VBAT(DPL)min 2.15 · max 2.5 V8
Battery depletion rising threshold VBAT(DPLZ)min 2.35 · max 2.7 V8
Bad adapter detection threshold V(VBUSMIN)typ 3.8 V8
Bad adapter detection current source I(BADSRC)typ 30 mA8
Minimum DC system voltage output VSYS(MIN)VBAT< VSYS(MIN), SYS_MIN = 3.5 V (REG03[3:1]=101), ISYS= 0 Amin 3.5 · typ 3.65 V8
Top switching MOSFET (HSFET) on-resistance between PMID and SW RON(HSFET)TJ = –40°C to +85°Ctyp 33 · max 45 mΩ9
Top switching MOSFET (HSFET) on-resistance between PMID and SW RON(HSFET)TJ = –40°C to +125°Ctyp 33 · max 53 mΩ9
Bottom switching MOSFET (LSFET) on-resistance between SW and GND RON(LSFET)TJ = –40°C to +85°Ctyp 18 · max 26 mΩ9
Bottom switching MOSFET (LSFET) on-resistance between SW and GND RON(LSFET)TJ = –40°C to +125°Ctyp 18 · max 30 mΩ9
BATFET forward voltage in supplement mode V(FWD)BAT discharge current 10 mAtyp 30 mV9
Battery good comparator rising threshold VBAT(GD)VBAT risingmin 3.4 · typ 3.55 · max 3.7 V9
Battery good comparator falling threshold VBAT(GD_HYST)VBAT fallingtyp 100 mV9
Typical charge voltage range VBAT(REG_RANGE)min 3.84 · max 4.608 V9
Typical charge voltage step VBAT(REG_STEP)typ 16 mV9
Charge voltage resolution accuracy VBAT(REG)VBAT = 4.208 V (REG06[7:2]=010111) or VBAT = 4.352 V (REG06[7:2]=100000), TJ = –40°C to +85°Cmin -0.5 · max 0.5 %9
Typical fast charge current regulation range I(CHG_REG_RANGE)min 0 · max 3008 mA9
Typical fast charge current regulation step I(CHG_REG_STEP)typ 64 mA9
Fast charge current regulation accuracy I(CHG_REG_ACC)VBAT = 3.1 V or 3.8 V, ICHG = 128 mA, TJ = –40°C to +85°Cmin -20 · max 20 %9
Fast charge current regulation accuracy I(CHG_REG_ACC)VBAT= 3.1 V or 3.8 V, ICHG = 256 mA, TJ = –40°C to +85°Cmin -10 · max 10 %9
Fast charge current regulation accuracy I(CHG_REG_ACC)VBAT= 3.1 V or 3.8 V, ICHG=1792 mA, TJ = –40°C to +85°Cmin -5 · max 5 %9
Battery LOWV falling threshold VBAT(LOWV)Fast charge to precharge, BATLOWV (REG06[1]) = 1min 2.6 · typ 2.8 · max 2.9 V9
Battery LOWV rising threshold VBAT(LOWV)Precharge to fast charge, BATLOWV (REG06[1])=1; typical 200-mV hysteresismin 2.8 · typ 3 · max 3.1 V9
Precharge current range I(PRECHG_RANGE)min 64 · max 1024 mA9
Typical precharge current step I(PRECHG_STEP)typ 64 mA9
Precharge current accuracy I(PRECHG_ACC)VBAT=2.6 V, IPRECHG = 256 mAmin -10 · max 10 %9
Termination current range I(TERM_RANGE)min 64 · max 1024 mA9
Typical termination current step I(TERM_STEP)typ 64 mA9
Termination current accuracy I(TERM_ACC)ITERM = 256 mA, ICHG<= 1344 mA, TJ = –20°C to +85°Cmin -12 · max 12 %9
Termination current accuracy I(TERM_ACC)ITERM = 256 mA, ICHG> 1344 mA, TJ = –20°C to +85°Cmin -20 · max 20 %9
Battery short voltage V(SHORT)VBAT fallingtyp 2 V9
Battery short voltage hysteresis V(SHORT_HYST)VBAT risingtyp 200 mV9
Battery short current I(SHORT)VBAT < 2.2 Vtyp 100 mA9
Recharge threshold below VBATREG V(RECHG)VBAT falling, VRECHG (REG06[0]=0) = 0typ 100 mV9
Recharge threshold below VBATREG V(RECHG)VBAT falling, VRECHG (REG06[0]=0) = 1typ 200 mV9
Battery discharge load current IBAT(LOAD)VBAT = 4.2 Vmin 15 mA9
System discharge load current ISYS(LOAD)VSYS = 4.2 Vmin 30 mA9
SYS-BAT MOSFET (BATFET) on-resistance RON(BATFET)TJ = 25°Ctyp 11 · max 13 mΩ9
SYS-BAT MOSFET (BATFET) on-resistance RON(BATFET)TJ = –40°C to +125°Ctyp 11 · max 19 mΩ9
Typical Input voltage regulation range VIN(DPM_RANGE)min 3.9 · max 15.3 V9
Typical Input voltage regulation step VIN(DPM_STEP)typ 100 mV9
Input voltage regulation accuracy VIN(DPM_ACC)VINDPM = 4.4 V, 9 V; both limits printed as 3%min 3 · max 3 %9
Typical Input current regulation range IIN(DPM_RANGE)min 100 · max 3250 mA9
Typical Input current regulation step IIN(DPM_STEP)typ 50 mA9
Input current 100-mA regulation accuracy VBAT = 5 V, current pulled from SW IIN(DPM100_ACC)IINLIM (REG00[5:0]) =100 mAmin 85 · typ 90 · max 100 mA9
IINMAX = KILIM/RILIM KILIMInput current regulation by ILIM pin = 1.5 Amin 320 · typ 355 · max 390 AxΩ10
Battery over-voltage threshold VBAT(OVP)VBAT rising, as percentage of VBAT(REG)typ 104 %10
Battery over-voltage hysteresis VBAT(OVP_HYST)VBAT falling, as percentage of VBAT(REG)typ 2 %10
System over-current threshold IBAT(FET_OCP)min 9 A10
Junction temperature regulation accuracy TREGREG08[1:0] = 11typ 120 °C10
Thermal shutdown rising temperature TSHUTTemperature risingtyp 160 °C10
Thermal shutdown hysteresis TSHUT(HYS)Temperature fallingtyp 30 °C10
T1 (0°C) threshold, charge suspended T1 below this temperature. V(T1)As percentage to V(REGN); buck modemin 72.75 · typ 73.25 · max 73.75 %10
Charge back to ICHG/2 (REG04[6:0]) and VREG (REG06[7:2]) above this temperature. V(T1_HYS)As percentage to V(REGN); buck modetyp 1.4 %10
T2 (10°C) threshold, charge back to ICHG/2 (REG04[6:0]) and VREG (REG06[7:2]) below this temperature. V(T2)As percentage to V(REGN); buck modemin 67.75 · typ 68.25 · max 68.75 %10
Charge back to ICHG (REG04[6:0]) and VREG (REG06[7:2]) above this temperature. V(T2_HYS)As percentage to V(REGN); buck modetyp 1.4 %10
T3 (45°C) threshold, charge back to ICHG (REG04[6:0]) and VREG-200 mV (REG06[7:2]) above this temperature. V(T3)As percentage to V(REGN); buck mode; minimum omitted because its printed suffix is ambiguoustyp 44.75 · max 45.25 %10
Charge back to ICHG (REG04[6:0]) and VREG (REG06[7:2]) below this temperature. V(T3_HYS)As percentage to V(REGN); buck modetyp 1 %10
T5 (60°C) threshold, charge suspended above this temperature. V(T5)As percentage to V(REGN); buck modemin 33.875 · typ 34.375 · max 34.875 %10
Charge back to ICHG (REG04[6:0]) and VREG-200 mV (REG06[7:2]) below this temperature. V(T5_HYS)As percentage to V(REGN); buck modetyp 1.25 %10
Cold temperature threshold, TS pin voltage rising threshold V(BCOLD0)As percentage to VREGN, REG01[5] = 0 (Approx. -10°C w/ 103AT); boost modemin 76.5 · typ 77 · max 77.5 %10
Cold temperature threshold, TS pin voltage falling threshold V(BCOLD0_HYS)As percentage to VREGN REG01[5] = 0; boost modetyp 1 %10
Cold temperature threshold 1, TS pin voltage rising threshold V(BCOLD1)As percentage to VREGN REG01[5] = 1 (Approximately –20°C w/ 103AT); boost modemin 79.5 · typ 80 · max 80.5 %10
Cold temperature threshold 1, TS pin voltage falling threshold V(BCOLD1_HYS)As percentage to VREGN REG01[5] = 1; boost modetyp 1 %10
Hot temperature threshold, TS pin voltage falling threshold V(BHOT0)As percentage to VREGN REG01[7:6] = 01 (Approx. 55°C w/ 103AT); boost modemin 37.25 · typ 37.75 · max 38.25 %10
Hot temperature threshold, TS pin voltage rising threshold V(BHOT0_HYS)As percentage to VREGN REG01[7:6] = 01; boost modetyp 3 %10
Hot temperature threshold 1, TS pin voltage falling threshold V(BHOT1)As percentage to VREGN REG01[7:6] = 00 (Approx. 60°C w/ 103AT); boost modemin 33.875 · typ 34.375 · max 34.875 %10
Hot temperature threshold 1, TS pin voltage rising threshold V(BHOT1_HYS)As percentage to VREGN REG01[7:6] = 00; boost modetyp 3 %10
Hot temperature threshold 2, TS pin voltage falling threshold V(BHOT2)As percentage to VREGN REG01[7:6] = 10 (Approx. 65°C w/ 103AT); boost modemin 30.75 · typ 31.25 · max 31.75 %10
Hot temperature threshold 2, TS pin voltage rising threshold V(BHOT2_HYS)As percentage to VREGN REG01[7:6] =10; boost modetyp 3 %10
PWM switching frequency, and digital clock FSWOscillator frequencymin 1.32 · max 1.68 MHz10
Maximum PWM duty cycle DMAXtyp 97 %10
Typical boost mode regulation voltage range V(OTG_REG_RANGE)min 4.55 · max 5.55 V10
Typical boost mode regulation voltage step V(OTG_REG_STEP)typ 64 mV10
Boost mode regulation voltage accuracy V(OTG_REG_ACC)I(VBUS) = 0 A, BOOSTV=4.998V (REG0A[7:4] = 0111)min -3 · max 3 %10
Minimum battery voltage to exit boost mode V(OTG_BAT1)BAT falling, MIN_VBAT_SEL=0min 2.7 · max 2.9 V10
Minimum battery voltage to exit boost mode V(OTG_BAT2)BAT falling, MIN_VBAT_SEL=1min 2.4 · max 2.6 V10
Minimum battery voltage to enter boost mode V(OTG_BAT_EN)BAT rising, MIN_VBAT_SEL=0min 2.9 · max 3.1 V10
Minimum battery voltage to enter boost mode V(OTG_BAT_EN)BAT rising, MIN_VBAT_SEL=1min 2.7 · max 2.9 V10
Typical boost mode output current range I(OTG)min 0.5 · max 2 A10
REGN LDO output voltage V(REGN)V(VBUS) = 9 V, I(REGN) = 40 mAmin 4.8 · typ 5 · max 5.5 V11
REGN LDO output voltage V(REGN)V(VBUS) = 5 V, I(REGN) = 20 mAmin 4.7 · typ 4.8 V11
REGN LDO current limit I(REGN)V(VBUS) = 9 V, V(REGN) = 3.8 Vmin 50 mA11
Resolution RESRising thresholdtyp 7 bits11
Typical battery voltage range VBAT(RANGE)V(VBUS) > VBAT + V(SLEEP) or OTG mode is enabledmin 2.304 · max 4.848 V11
Typical battery voltage range VBAT(RANGE)V(VBUS) < VBAT + V(SLEEP) and OTG mode is disabled; minimum is VSYS_MINmax 4.848 V11
Typical battery voltage resolution V(BAT_RES)typ 20 mV11
Typical system voltage range V(SYS_RANGE)V(VBUS) > VBAT + V(SLEEP) or OTG mode is enabledmin 2.304 · max 4.848 V11
Typical system voltage range V(SYS_RANGE)V(VBUS) < VBAT + V(SLEEP) and OTG mode is disabled; minimum is VSYS_MINmax 4.848 V11
Typical system voltage resolution V(SYS_RES)typ 20 mV11
Typical VVBUS voltage range V(VBUS_RANGE)V(VBUS) > VBAT + V(SLEEP) or OTG mode is enabledmin 2.6 · max 15.3 V11
Typical VVBUS voltage resolution V(VBUS_RES)typ 100 mV11
Typical battery charge current range IBAT(RANGE)V(VBUS) > VBAT + V(SLEEP) and VBAT > VBAT(SHORT)min 0 · max 6.4 A11
Typical battery charge current resolution IBAT(RES)typ 50 mA11
Typical TS voltage range V(TS_RANGE)min 21 · max 80 %11
Typical TS voltage resolution V(TS_RES)typ 0.47 %11
Input high threshold level VIHLOGIC I/O PIN (OTG, CE, PSEL, QON)min 1.3 V11
Input low threshold level VILLOGIC I/O PIN (OTG, CE, PSEL, QON)max 0.4 V11
High Level Leakage Current IIN(BIAS)LOGIC I/O PIN (OTG, CE, PSEL, QON); Pull-up rail 1.8 Vmax 1 uA11
Internal /QON pull-up V(QON)V(VBUS) = 9 Vtyp 5.8 V11
Internal /QON pull-up V(QON)V(VBUS) = 5 Vtyp 4.3 V11
Internal /QON pull-up resistance R(QON)typ 200 kΩ11
Output low threshold level VOLLOGIC I/O PIN (INT, STAT, PG); Sink current = 5 mA, sink currentmax 0.4 V11
High level leakage current IOUT_BIASLOGIC I/O PIN (INT, STAT, PG); Pull-up rail 1.8 Vmax 1 uA11
Input high threshold level, SCL and SDA VIHI2C INTERFACE (SCL, SDA); Pull-up rail 1.8 Vmin 1.3 V11
Input low threshold level VILI2C INTERFACE (SCL, SDA); Pull-up rail 1.8 Vmax 0.4 V11
Output low threshold level VOLI2C INTERFACE (SCL, SDA); Sink current = 5 mA, sink currentmax 0.4 V11
High level leakage current IBIASI2C INTERFACE (SCL, SDA); Pull-up rail 1.8 Vmax 1 uA11

Pins, by the datasheet

25
1 VBUS
Charger input voltage; connect a 1-uF ceramic capacitor to PGND close to the IC. · p. 5
2 PSEL
Power source selection: high selects USB host source, low selects adapter source. · p. 5
3 PG
Active low power good indicator; pull up through 10-kΩ resistor. · p. 5
4 STAT
Charge status output; low during charging, high when complete or disabled, blinks at 1 Hz on faults; pull up through 10-kΩ resistor. · p. 5
5 SCL
I2C clock; connect to logic rail through 10-kΩ resistor. · p. 5
6 SDA
I2C data; connect to logic rail through 10-kΩ resistor. · p. 5
7 INT
Interrupt output sends active low 256-us pulses for status and faults; pull up through 10-kΩ resistor. · p. 5
8 OTG
Enables boost mode when high, OTG_CONFIG = 1, and no input source is detected at VBUS. · p. 5
9 CE
Active low charge enable; charging requires CHG_CONFIG = 1; must be pulled high or low. · p. 5
10 ILIM
Input current limit and monitoring input; connect resistor to ground to set maximum input current. · p. 5
11 TS
Temperature qualification input; connect NTC thermistor and resistor divider from REGN to ground; recommended thermistor is 103AT-2. · p. 6
12 QON
BATFET enable and reset control; low pulses exit ship mode or reset system power; internal pull-up maintains default high. · p. 6
13 BAT
Battery positive terminal connection; internal BATFET connects BAT to SYS; place 10uF close to BAT. · p. 6
14 BAT
Battery positive terminal connection; internal BATFET connects BAT to SYS; place 10uF close to BAT. · p. 6
15 SYS
System power connection; converter maintains minimum system voltage; place 20uF close to SYS. · p. 6
16 SYS
System power connection; converter maintains minimum system voltage; place 20uF close to SYS. · p. 6
17 PGND
Power ground; connect directly to input and output capacitor grounds and join analog ground near the IC. · p. 6
18 PGND
Power ground; connect directly to input and output capacitor grounds and join analog ground near the IC. · p. 6
19 SW
Switching node connected to output inductor; connect bootstrap capacitor to BTST. · p. 6
20 SW
Switching node connected to output inductor; connect bootstrap capacitor to BTST. · p. 6
21 BTST
PWM high side driver supply; connect 0.047 uF bootstrap capacitor to SW. · p. 6
22 REGN
PWM low side driver supply output and TS bias rail; connect 4.7 uF ceramic capacitor to analog ground close to IC. · p. 6
23 PMID
Connected to drains of reverse blocking MOSFET and HSFET; connect remaining input capacitance to PGND. · p. 6
24 NC
No Connect. · p. 6
PowerPAD PowerPAD™
Exposed thermal pad; solder to board with vias star-connecting to PGND and ground plane. · p. 6

Ordering codes, by the datasheet

6
BQ25896RTWR
WQFN (RTW), 24 pins · 3000, LARGE T&R; operating temperature -40 to 85 °C; MSL Level-1-260C-UNLIM · p. 57
BQ25896RTWR.A
WQFN (RTW), 24 pins · 3000, LARGE T&R; operating temperature -40 to 85 °C; MSL Level-1-260C-UNLIM · p. 57
BQ25896RTWR.B
WQFN (RTW), 24 pins · 3000, LARGE T&R; operating temperature -40 to 85 °C; MSL Level-1-260C-UNLIM · p. 57
BQ25896RTWT
WQFN (RTW), 24 pins · 250, SMALL T&R; operating temperature -40 to 85 °C; MSL Level-2-260C-1 YEAR · p. 57
BQ25896RTWT.A
WQFN (RTW), 24 pins · 250, SMALL T&R; operating temperature -40 to 85 °C; MSL Level-2-260C-1 YEAR · p. 57
BQ25896RTWT.B
WQFN (RTW), 24 pins · 250, SMALL T&R; operating temperature -40 to 85 °C; MSL Level-2-260C-1 YEAR · p. 57

Open-source boards using it

2
  • 4 layers68 × 58 mmPcb pcBOT, the printed circuit board in 3D

    Pcb pcBOT

    theocond48/2526_Projet1A_PcBot_G5

    Le schéma ci-dessous illustre l'organisation du système. Le microcontrôleur (MCU) agit comme le cerveau central, coordonnant les capteurs (entrées), les actionneurs (sorties) et la communication.

    70 partsMIT
  • 4 layers100 × 60 mmRouted c4, the printed circuit board in 3D

    Routed c4

    Sanu0910/RFMW-ANT

    86 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the BQ25896RTW?

Yes. The symbol is EasyEDA_Cloud:BQ25896RTWR and the footprint EasyEDA_Cloud:VQFN-24_L4.0-W4.0-P0.50-TL-EP2.7, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the BQ25896RTW?

QFN-24-EP(4x4), with 25 pins. Its footprint is drawn on this page.

Where is the BQ25896RTW datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the BQ25896RTW?

JLCPCB lists it as part C181475, with 766 in stock; the sellers' links on this page open their listings.

What can replace the BQ25896RTW?

Parts like it in the library: the BQ25616RTW by Texas Instruments, the BQ24296MRGE by Texas Instruments, the BQ24195LRGE by Texas Instruments and the BQ25883RGE by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the BQ25896RTW?

2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.