BQ25883RGE
Texas InstrumentsExtended
-40℃~+85℃ 12uA 2 2.2A 3.9V~6.2V 8.4V Charging IC I2C Lithium Battery Support Support VQFN-24-EP(4x4) Battery Management ROHS
- Part id
- ti/BQ25883RGE
- Category
- Battery Management
- Package
- VQFN-24-EP(4x4)
- Pins
- 25
- In stock
- 1,015 at JLCPCB (C544362)
Overview
The BQ25883RGE is a battery Management made by Texas Instruments in a VQFN-24-EP(4x4) package with 25 pins. -40℃~+85℃ 12uA 2 2.2A 3.9V~6.2V 8.4V Charging IC I2C Lithium Battery Support Support VQFN-24-EP(4x4) Battery Management ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:BQ25883RGER, from EasyEDA) and its footprint (EasyEDA_Cloud:VQFN-24_L4.0-W4.0-P0.50-TL-EP2.7, from EasyEDA), ready for a KiCad board. 1,015 are in stock at JLCPCB (part C544362).
Symbol
Footprint
From the datasheet
16- Supply, least
- 3.9 V · VBUS, recommended operating min · p. 7
- Supply, most
- 6.2 V · VBUS, recommended operating max · p. 7
- Supply, absolute maximum
- 20 V · VBUS, converter not switching, absolute max · p. 6
- Works from
- -40 °C · Operating free-air temperature min · p. 6
- Works up to
- 85 °C · Operating free-air temperature max · p. 6
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 6
- Takes working
- 3 mA · VBUS typical, 5 V input, 7.6 V battery, converter switching, ISYS = 0 A · p. 7
- Takes asleep
- 30 µA · VBUS typical, 5 V, High-Z mode, no battery, ADC disabled, 25°C · p. 7
- Gives
- 2 A · Rated charge current max · p. 1
- A pin gives at most
- 6 mA · /INT, STAT, /PG output sink current absolute max per pin · p. 6
- Junction to air (RGE (VQFN))
- 32.4 K/W · Junction-to-ambient thermal resistance · p. 6
- Junction to case (RGE (VQFN))
- 26.7 K/W · Junction-to-case top thermal resistance · p. 6
- Junction to board (RGE (VQFN))
- 10.7 K/W · Junction-to-board thermal resistance · p. 6
- Gives
- 2.2 A · maximum battery charge current · p. 23
- Switches at
- 1.5 MHz · typical boost converter PWM switching frequency · p. 10
- Data rate, most
- 400 kbit/s · maximum I2C fast-mode data rate · p. 31
What it is and has
14- Battery charger
- 2-cell Li-Ion and Li-polymer, 2-A boost switch-mode charger with power path · p. 1
- Switching frequency
- 1.5MHz · p. 1
- Control
- I2C with power path management · p. 1
- ADC
- Integrated 16-bit for system monitoring · p. 1
- Integration
- All MOSFETs, current sensing and loop compensation · p. 1
- Package
- VQFN (24), 4.00 mm x 4.00 mm · p. 1
- Charger
- 2-cell, 2-A boost-mode battery charger with power path and USB OTG · p. 1
- Charge voltage regulation accuracy
- ±0.5% · p. 1
- Charge current regulation accuracy
- ±5% · p. 1
- Input current regulation accuracy
- ±7.5% · p. 1
- Protection
- Thermal regulation and thermal shutdown · p. 1
- Battery support
- 2-cell Li-Ion and Li-polymer · p. 68
- Control interface
- I2C · p. 68
- Integrated bootstrap diode
- High-side gate drive · p. 68
Around it
15- res 10-kΩ
- between STAT and pull-up rail; Charge status output pull-up. · p. 4
- res 10-kΩ
- between SDA and pull up rail; I2C data pull-up. · p. 4
- res 10-kΩ
- between SCL and pull up rail; I2C clock pull-up. · p. 4
- res 10-kΩ
- between INT and pull up rail; Interrupt output pull-up. · p. 4
- res 10-kΩ
- between PG and pull up rail; Power-good output pull-up. · p. 5
- other 103AT-2 thermistor
- between TS and GND; NTC for temperature qualification; program the window with a resistor divider from REGN to TS to GND. · p. 4
- cap 4.7-µF
- between REGN and GND; Ceramic bypass capacitor. · p. 5
- cap 47nF
- between SW and BTST; Bootstrap capacitor. · p. 5
- cap 10-µF
- between BAT and GND; Minimum recommended capacitance after derating; place close to BAT and GND. · p. 5
- cap 2x22-µF
- between SYS and PGND; Capacitance after derating; place close to SYS and PGND. · p. 5
- cap 10 uF
- between PMID and GND; Typical PMID capacitance; minimum total input low-ESR capacitance on VBUS and PMID is 10 uF after derating. · p. 5
- cap 1-µF
- between VBUS and GND; At least 1-uF ceramic capacitor, placed as close to the IC as possible. · p. 5
- res 820-Ω
- between ILIM and GND; Example input current limit resistor for 1.55 A using KILIM = 1276 max. · p. 30
- cap 10-μF
- between PMID and GND; Input decoupling for up to 3.3-A input current; low ESR X7R or X5R ceramic preferred, placed close to PMID and GND. A voltage rating of 25 V or higher is preferred for up to 5-V input. · p. 69
- res 0-Ω
- between analog ground and power ground; Alternative connection between analog and power grounds; the thermal pad can instead serve as their single connection point. · p. 74
Specifications
174| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Voltage Range (with respect to GND unless otherwise specified) | VBUS (converter not switching) | min -0.3 · max 20 V | 6 |
| Voltage Range (with respect to GND unless otherwise specified) | PMID (converter not switching) | min -0.3 · max 8.5 V | 6 |
| Voltage Range (with respect to GND unless otherwise specified) | BAT, SYS (converter not switching) | min -0.3 · max 12 V | 6 |
| Voltage Range (with respect to GND unless otherwise specified) | SW | min -0.3 · max 13 V | 6 |
| Voltage Range (with respect to GND unless otherwise specified) | BTST | min -0.3 · max 19 V | 6 |
| Voltage Range (with respect to GND unless otherwise specified) | REGN, STAT, /PG, TS | min -0.3 · max 6 V | 6 |
| Voltage Range (with respect to GND unless otherwise specified) | ILIM | min -0.3 · max 5 V | 6 |
| Voltage Range (with respect to GND unless otherwise specified) | BTST to SW | min -0.3 · max 6 V | 6 |
| Voltage Range (with respect to GND unless otherwise specified) | D+, D-, /CE, SDA, SCL, /INT | min -0.3 · max 6 V | 6 |
| Output Sink Current | /INT, STAT, /PG | max 6 mA | 6 |
| Junction Temperature, TJ TJ | min -40 · max 150 °C | 6 | |
| Storage temperature, Tstg Tstg | min -40 · max 150 °C | 6 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; rated value ±2000 V | max 2000 V | 6 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per JEDEC specification JESD22-C101; rated value ±250 V | max 250 V | 6 |
| Average input current (VBUS) IVBUS | max 3.3 A | 6 | |
| Average charge current (IBAT) IBAT | max 2.2 A | 6 | |
| RMS discharging current with internal MOSFET IBAT_RMS | max 5 A | 6 | |
| Peak discharging current with internal MOSFET IBAT_PK | up to 1us | max 9 A | 6 |
| Battery Voltage VBAT | The inherent switching noise voltage spikes should not exceed the absolute maximum rating on SW pin. | max 9.2 V | 6 |
| Operating free-air temperature range TA | min -40 · max 85 °C | 6 | |
| Junction-to-ambient thermal resistance RΘJA | BQ25883, RGE (VQFN), 24-PIN | typ 32.4 °C/W | 6 |
| Junction-to-case (top) thermal resistance RΘJC(top) | BQ25883, RGE (VQFN), 24-PIN | typ 26.7 °C/W | 6 |
| Junction-to-board thermal resistance RΘJB | BQ25883, RGE (VQFN), 24-PIN | typ 10.7 °C/W | 6 |
| Junction-to-top characterization parameter ΨJT | BQ25883, RGE (VQFN), 24-PIN | typ 0.4 °C/W | 6 |
| Junction-to-board characterization parameter ΨJB | BQ25883, RGE (VQFN), 24-PIN | typ 10.6 °C/W | 6 |
| Junction-to-case (bottom) thermal resistance RΘ JC(bot) | BQ25883, RGE (VQFN), 24-PIN | typ 3.7 °C/W | 7 |
| Battery discharge current (BAT) IBAT | VBAT = 9 V, No VBUS, SCL, SDA = 0 V or 1.8 V, TJ=25C, ADC Disabled | typ 12 · max 14 uA | 7 |
| Battery discharge current (BAT) IBAT | VBAT = 9 V, No VBUS, SCL, SDA = 0 V or 1.8 V, TJ < 85C, ADC Disabled | typ 12 · max 20 uA | 7 |
| Input supply current (VBUS) in HIZ IVBUS_HIZ | VBUS = 5 V, High-Z Mode, no battery, ADC Disabled, 25℃ | typ 30 · max 38 uA | 7 |
| Input supply current (VBUS) in HIZ IVBUS_HIZ | VBUS = 5 V, High-Z Mode, no battery, ADC Disabled, <85℃ | typ 30 · max 48 uA | 7 |
| Input supply current (VBUS) IVBUS | VBUS = 5 V, VBAT = 7.6 V, converter not switching | typ 1.5 · max 3 mA | 7 |
| Input supply current (VBUS) IVBUS | VBUS = 5 V, VBAT = 7.6 V, converter switching, ISYS = 0A | typ 3 mA | 7 |
| Battery discharge current in OTG mode IBAT_OTG | VBAT = 8.4 V, OTG Buck Mode, IVBUS = 0A, converter switching | typ 3 mA | 7 |
| VBUS operating range VVBUS_OP | min 3.9 · max 6.2 V | 7 | |
| VBUS rising for active I2C, no battery VVBUS_UVLO_RISING | VBUS rising | typ 3.3 · max 3.68 V | 7 |
| VBUS over-voltage rising threshold VVBUS_OV | VBUS rising | min 6.2 · max 6.6 V | 7 |
| VBUS over-voltage falling threshold VVBUS_OV | VBUS falling | min 5.9 · max 6.4 V | 7 |
| Battery for active I2C VBAT_UVLO_RISING | VBAT rising | min 3.7 · typ 4 · max 4.42 V | 7 |
| Bad adapter detection threshold VPOORSRC_FALLING | VBUS falling below VPOORSRC_FALLING | typ 3.7 V | 7 |
| Bad adapter detection current source IPOORSRC | typ 15 mA | 7 | |
| System Regulation Voltage VSYS_MIN | VBAT < SYS_MIN[3:0] = 0010, Charge Disabled (EN_CHG = 0) | min 6.2 · typ 6.4 V | 7 |
| Typical charge voltage regulation range VREG_RANGE | min 6.8 · max 9.2 V | 7 | |
| Typical charge voltage step VREG_STEP | typ 10 mV | 7 | |
| Charge voltage VREG_ACC | VREG = 8.40 V, TJ = 0°C to 85°C | min 8.35 · typ 8.4 · max 8.44 V | 7 |
| Charge current regulation range ICHG_RANGE | min 100 · max 2200 mA | 7 | |
| Charge current regulation step ICHG_STEP | typ 50 mA | 7 | |
| Fast Charge current regulation accuracy ICHG_ACC | ICHG = 1000 mA, VBAT = 6.2 V or 7.6 V, TJ = 0°C to 85°C | min -7.5 · max 7.5 % | 7 |
| Fast Charge current regulation accuracy ICHG_ACC | ICHG = 500mA, VBAT = 6.2 V or 7.6 V, TJ = 0°C to 85°C | min -15 · max 15 % | 7 |
| Fast Charge current regulation accuracy ICHG_ACC | ICHG = 250 mA, VBAT = 6.2 V or 7.6 V, TJ = 0°C to 85°C | min -25 · max 25 % | 8 |
| Precharge current range IPRECHG_RANGE | min 50 · max 800 mA | 8 | |
| Typical precharge current step IPRECHG_STEP | typ 50 mA | 8 | |
| Precharge current accuracy IPRECHG_ACC | VBAT = 5.2 V, IPRECHG = 200 mA, TJ = 25°C | min 170 · max 237 mA | 8 |
| Precharge current accuracy IPRECHG_ACC | VBAT = 5.2 V, IPRECHG = 200 mA, TJ = 0°C to 85°C | min 150 · max 245 mA | 8 |
| Termination current range ITERM_RANGE | min 50 · max 800 mA | 8 | |
| Typical termination current step ITERM_STEP | typ 50 mA | 8 | |
| Termination current accuracy ITERM_ACC | ICHG = 1.5A, ITERM = 150 mA, TJ = 25°C | min 143 · max 157 mA | 8 |
| Termination current accuracy ITERM_ACC | ICHG = 1.5A, ITERM = 150 mA, TJ = 0°C to 85°C | min 120 · max 180 mA | 8 |
| Termination current accuracy ITERM_ACC | ICHG = 1.5A, ITERM = 50 mA, TJ = 25°C | min 45 · max 60 mA | 8 |
| Termination current accuracy ITERM_ACC | ICHG = 1.5A, ITERM = 50 mA, TJ = 0°C to 85°C | min 22 · max 75 mA | 8 |
| Short Battery Voltage rising threshold to start pre-charging VBAT_SHORT_RISING | VBAT rising | min 4.1 · typ 4.4 · max 4.7 V | 8 |
| Short Battery Voltage falling threshold to stop pre-charging VBAT_SHORT_FALLING | VBAT falling | min 3.7 · typ 4 · max 4.3 V | 8 |
| Low Battery Voltage trickle charging current IBAT_SHORT | VBAT < 4.4 V | typ 100 mA | 8 |
| VBAT LOWV Rising threshold to start fast-charging VBAT_LOWV_RISING | VBAT rising, VBATLOWV = 6.0 V | min 5.7 · typ 6 · max 6.3 V | 8 |
| VBAT LOWV Rising threshold to start fast-charging VBAT_LOWV_RISING | VBAT rising, VBATLOW = 5.6 V | min 5.3 · typ 5.6 · max 5.9 V | 8 |
| VBAT LOWV Falling threshold to stop fast-charging VBAT_LOWV_FALLING | VBAT falling, VBATLOW = 5.6 V | min 4.9 · typ 5.2 · max 5.5 V | 8 |
| VBAT LOWV Falling threshold to stop fast-charging VBAT_LOWV_FALLING | VBAT falling, VBATLOWV = 6.0 V | min 5.3 · typ 5.6 · max 5.9 V | 8 |
| Recharge threshold below VREG VRECHG | VBAT falling, VRECHG[1:0] = 01 | typ 200 mV | 8 |
| Recharge threshold below VREG VRECHG | VBAT falling, VRECHG[1:0] = 10 | typ 300 mV | 8 |
| High-side switching MOSFET on-resistance between SW and SYS (Q2) RON_QHS (Q2) | TJ = 25°C | typ 32 · max 34.2 mΩ | 8 |
| High-side switching MOSFET on-resistance between SW and SYS (Q2) RON_QHS (Q2) | TJ = – 40°C to 125°C | typ 32 · max 46.5 mΩ | 8 |
| Low-side switching MOSFET on-resistance between SW and GND (Q3) RON_QLS (Q3) | TJ = 25°C | typ 42 · max 45.8 mΩ | 8 |
| Low-side switching MOSFET on-resistance between SW and GND (Q3) RON_QLS (Q3) | TJ = – 40°C to 125°C | typ 42 · max 62.9 mΩ | 8 |
| MOSFET on-resistance between SYS and BAT (Q4) RON_QBAT (Q4) | TJ = 25°C | typ 18 · max 18.8 mΩ | 8 |
| MOSFET on-resistance between SYS and BAT (Q4) RON_QBAT (Q4) | TJ = – 40°C - 85°C | typ 18 · max 22.5 mΩ | 8 |
| BAT Discharge current source IBAT_DISCHG | VBAT = 8V, EN_BAT_DISCHG = 1 | min 8 · typ 11.5 · max 16 mA | 8 |
| Input voltage regulation range VINDPM_RANGE | min 3.9 · max 5.5 V | 8 | |
| Input voltage regulation step VINDPM_STEP | typ 100 mV | 8 | |
| Input voltage limit VINDPM | VINDPM = 3.9 V | min 3.783 · typ 3.9 · max 4.017 V | 8 |
| Input voltage limit VINDPM | VINDPM = 4.4 V | min 4.268 · typ 4.4 · max 4.532 V | 8 |
| Input current regulation range IINDPM_RANGE | min 500 · max 3300 mA | 8 | |
| Input current regulation step IINDPM_STEP | typ 100 mA | 8 | |
| Input current regulation limit IINDPM_ACC | IINDPM = 500 mA | min 438 · typ 469 · max 500 mA | 8 |
| Input current regulation limit IINDPM_ACC | IINDPM = 900 mA | min 765 · typ 832 · max 900 mA | 8 |
| Input current regulation limit IINDPM_ACC | IINDPM = 2500 mA | min 2125 · typ 2312 · max 2500 mA | 8 |
| Input current regulation limit IINDPM_ACC | IINDPM = 3000 mA | min 2550 · typ 2775 · max 3000 mA | 8 |
| IINMAX = KILIM/RILIM KILIM | Input Current regulation by ILIM pin = 1.5A | min 1012 · typ 1098 · max 1185 Ax Ω | 8 |
| Blocking MOSFET on-resistance between VBUS and PMID (QBLK) RON_QBLK (Q1) | TJ = 25°C | typ 33 · max 36.8 mΩ | 9 |
| Blocking MOSFET on-resistance between VBUS and PMID (QBLK) RON_QBLK (Q1) | TJ = – 40°C to 125°C | typ 33 · max 50.9 mΩ | 9 |
| D+/D- Voltage Source (600 mV) VD+D-_600MVSRC | min 500 · typ 600 · max 700 mV | 9 | |
| D+ Current Source (10 uA) ID+_10UASRC | VD + = 200 mV | min 7 · typ 10 · max 14 uA | 9 |
| D+/D- Current Sink (100 uA) ID+D-_100UASNK | VD + = 500 mV | min 50 · typ 100 · max 150 uA | 9 |
| D+/D- Comparator Threshold for Secondary Detection VD+D-_0P325 | D + pin Rising | min 250 · max 400 mV | 9 |
| D- Resistor to Ground (19 kΩ) RD-_19K | VD- = 500 mV | min 14.25 · max 24.8 kΩ | 9 |
| D+ Comparator Threshold for Data Contact Detection VD+_0P8 | D + pin Rising | max 800 mV | 9 |
| D+/D- Threshold for Non-standard adapter VD+D-_1P2 | min 1.05 · max 1.35 V | 9 | |
| D+/D- Comparator Threshold for Non-standard adapter VD+D-_2P0 | min 1.85 · max 2.15 V | 9 | |
| D+/D- Threshold for Non-standard adapter VD+D-_2P8 | min 2.55 · max 2.85 V | 9 | |
| D+/D- Leakage Current ID+D-_LKG | HiZ | min -1 · max 1 uA | 9 |
| Battery over-voltage rising threshold VBAT_OVP_RISING | VBAT rising, as percentage of VREG | min 102.5 · typ 104 · max 105 % | 9 |
| Battery over-voltage falling threshold VBAT_OVP_FALLING | VBAT falling, as percentage of VREG | min 101 · typ 102 · max 103.3 % | 9 |
| Junction temperature regulation accuracy TREG | TREG = 120°C | typ 120 °C | 9 |
| Thermal Shutdown Rising threshold TSHUT_RISING | Temperature Increasing | typ 150 °C | 9 |
| Thermal Shutdown Falling threshold TSHUT_RISING | Temperature Decreasing | typ 120 °C | 9 |
| TS pin voltage rising. T1 (0°C) threshold, Charge suspended below this temperature. VT1 | As Percentage to REGN; JEITA THERMISTOR COMPARATOR (BOOST MODE) | min 72.75 · typ 73.25 · max 73.75 % | 9 |
| TS pin voltage falling. Charge re-enabled to ICHG/2 and VREG above this temperature VT1_HYS | As Percentage to REGN; JEITA THERMISTOR COMPARATOR (BOOST MODE) | typ 1.3 % | 9 |
| TS pin voltage rising. T2 (10°C) threshold, charge set to ICHG/2 and VREG below this temperature VT2 | As Percentage to REGN; JEITA THERMISTOR COMPARATOR (BOOST MODE) | min 67.75 · typ 68.25 · max 68.75 % | 9 |
| TS pin voltage falling. Charge set to ICHG and VREG above this temperature VT2_HYS | As Percentage to REGN; JEITA THERMISTOR COMPARATOR (BOOST MODE) | typ 1.2 % | 9 |
| TS pin voltage falling. T3 (45°C) threshold, charge set to ICHG and 8.1 V above this temperature. VT3 | As Percentage to REGN; JEITA THERMISTOR COMPARATOR (BOOST MODE) | min 44.25 · typ 44.75 · max 45.25 % | 9 |
| TS pin voltage rising. Charge set to ICHG and VREG below this temperature VT3_HYS | As Percentage to REGN; JEITA THERMISTOR COMPARATOR (BOOST MODE) | typ 1 % | 9 |
| TS pin voltage falling. T5 (60°C) threshold, charge suspended above this temperature. VT5 | As Percentage to REGN; JEITA THERMISTOR COMPARATOR (BOOST MODE) | min 33.875 · typ 34.375 · max 34.875 % | 9 |
| TS pin voltage rising. Charge set to ICHG and 8.1 V below this temperature VT5_HYS | As Percentage to REGN; JEITA THERMISTOR COMPARATOR (BOOST MODE) | typ 1.35 % | 9 |
| Cold Temperature Threshold 0, TS pin Voltage Rising Threshold VBCOLD0 | As Percentage to REGN, BCOLD = 0 (Approx. – 10°C w/ 103AT) | min 76.5 · typ 77 · max 77.5 % | 10 |
| Cold Temperature Threshold 0, TS pin Voltage Falling Threshold VBCOLD0_HYS | As Percentage to REGN | typ 1 % | 10 |
| Cold Temperature Threshold 1, TS pin Voltage Rising Threshold VBCOLD1 | As Percentage to REGN, BCOLD = 1 (Approx. – 20°C w/ 103AT) | min 79.5 · typ 80 · max 80.5 % | 10 |
| Cold Temperature Threshold 1, TS pin Voltage Falling Threshold VBCOLD1_HYS | As Percentage to REGN | typ 1 % | 10 |
| Hot Temperature Threshold 0, TS pin Voltage Falling Threshold VBHOT0 | As Percentage to REGN, BHOT[1:0] = 01 (Approx. 55°C w/ 103AT) | min 37.25 · typ 37.75 · max 38.25 % | 10 |
| Hot Temperature Threshold 0, TS pin Voltage Rising Threshold VBHOT0_HYS | As Percentage to REGN | typ 3 % | 10 |
| Hot Temperature Threshold 1, TS pin Voltage falling Threshold VBHOT1 | As Percentage to REGN, BHOT[1:0] = 00 (Approx. 60°C w/ 103AT) | min 33.875 · typ 34.375 · max 34.875 % | 10 |
| Hot Temperature Threshold 1, TS pin Voltage rising Threshold VBHOT1_HYS | As Percentage to REGN | typ 3 % | 10 |
| Hot Temperature Threshold 2, TS pin Voltage falling Threshold VBHOT2 | As Percentage to REGN, BHOT[1:0] = 10 (Approx. 65°C w/ 103AT) | min 30.75 · typ 31.25 · max 31.75 % | 10 |
| Hot Temperature Threshold 2, TS pin Voltage rising Threshold VBHOT2_HY2 | As Percentage to REGN | typ 3 % | 10 |
| PWM switching frequency FSW | Oscillator frequency | min 1.35 · typ 1.5 · max 1.65 MHz | 10 |
| Battery voltage exiting OTG mode VOTG_BAT | VBAT falling | min 5.85 · typ 6 · max 6.15 V | 10 |
| Typical OTG Buck mode voltage regulation range VOTG_RANGE | min 4.5 · max 5.5 V | 10 | |
| Typical OTG Buck mode voltage regulation step VOTG_STEP | typ 100 mV | 10 | |
| OTG Buck mode voltage regulation accuracy VOTG_ACC | IVBUS = 0A, OTG_VLIM = 5.1 V | min -3 · max 3 % | 10 |
| Typical OTG Buck mode current regulation range IOTG_RANGE | min 0.5 · max 2 A | 10 | |
| Typical OTG Buck mode current regulation step IOTG_STEP | typ 100 mA | 10 | |
| OTG Buck mode current regulation accuracy IOTG_ACC | OTG_ILIM = 1A | min -15 · typ -7.5 · max 0 % | 10 |
| OTG Buck mode over-voltage threshold VOTG_OVP | min 5.8 · typ 6 V | 10 | |
| REGN LDO output voltage VREGN | VVBUS = 5 V, IREGN = 20 mA | min 4.7 · typ 4.8 · max 5.15 V | 10 |
| REGN LDO current limit IREGN | VVBUS = 5 V, VREGN = 3.8 V | min 50 mA | 10 |
| Conversion time, each measurement tADC_CONV | ADC_SAMPLE[1:0] = 11 | typ 24 ms | 10 |
| Conversion time, each measurement tADC_CONV | ADC_SAMPLE[1:0] = 10 | typ 12 ms | 10 |
| Conversion time, each measurement tADC_CONV | ADC_SAMPLE[1:0] = 01 | typ 6 ms | 10 |
| Conversion time, each measurement tADC_CONV | ADC_SAMPLE[1:0] = 00 | typ 3 ms | 10 |
| Effective resolution ADCRES | ADC_SAMPLE[1:0] = 11 | min 14 · typ 15 bits | 10 |
| Effective resolution ADCRES | ADC_SAMPLE[1:0] = 10 | min 13 · typ 14 bits | 10 |
| Effective resolution ADCRES | ADC_SAMPLE[1:0] = 01 | min 12 · typ 13 bits | 10 |
| Effective resolution ADCRES | ADC_SAMPLE[1:0] = 00 | min 10 · typ 12 bits | 10 |
| ADC BUS current range IBUS_ADC_RANGE | min 0 · max 4 A | 11 | |
| ADC BUS current LSB IBUS_ADC_LSB | typ 1 mA | 11 | |
| ADC BAT current range IBAT_ADC_RANGE | min 0 · max 4 A | 11 | |
| ADC BAT current LSB IBAT_ADC_LSB | typ 1 mA | 11 | |
| ADC BUS voltage range VBUS_ADC_RANGE | min 0 · max 6.5 V | 11 | |
| ADC BUS voltage LSB VBUS_ADC_LSB | typ 1 mV | 11 | |
| ADC SYS voltage range VSYS_ADC_RANGE | min 0 · max 10 V | 11 | |
| ADC SYS voltage LSB VSYS_ADC_LSB | typ 1 mV | 11 | |
| ADC BAT voltage range VBAT_ADC_RANGE | min 0 · max 10 V | 11 | |
| ADC BAT voltage LSB VBAT_ADC_LSB | typ 1 mV | 11 | |
| ADC TS voltage range VTS_ADC_RANGE | min 20 · max 80 % | 11 | |
| ADC TS voltage LSB VTS_ADC_LSB | typ 0.098 % | 11 | |
| ADC Die temperature range VTDIE_ADC_RANGE | min 0 · max 150 °C | 11 | |
| ADC Die temperature LSB VTDIE_ADC_LSB | typ 0.5 °C | 11 | |
| Input high threshold level, SDA and SCL VIH | Pull-up rail 1.8 V | min 1.3 V | 11 |
| Input low threshold level VIL | Pull-up rail 1.8 V | max 0.4 V | 11 |
| Output low threshold level VOL | I2C interface (SCL, SDA); Sink current = 5 mA | max 0.4 V | 11 |
| High level leakage current IBIAS | Pull-up rail 1.8 V | max 1 uA | 11 |
| Input high threshold level, /CE VIH_CEZ | min 1.3 V | 11 | |
| Input low threshold level, /CE VIL_CEZ | max 0.4 V | 11 | |
| High level leakage current, /CE IIN_BIAS_CEZ | Pull-up rail 1.8 V | max 2.5 uA | 11 |
| Output low threshold level VOL | Logic O pin (/INT, /PG, STAT); Sink current = 5 mA | max 0.4 V | 11 |
| High level leakage current IOUT_BIAS | Logic O pin (/INT, /PG, STAT); Pull-up rail 1.8 V | max 1 uA | 11 |
| VBUS OVP reaction time tVBUS_OV | VBUS rising above VBUS_OV threshold to converter turn off | typ 200 ns | 11 |
| Bad adapter detection duration tPOORSRC | typ 30 ms | 11 | |
| Deglitch time for charge termination tTERM_DGL | Charge current falling below ITERM | typ 250 ms | 11 |
| Deglitch time for recharge threshold tRECGH_DGL | BAT voltage falling below VRECHG = 100 mV | typ 250 ms | 11 |
| Deglitch time for battery over-voltage to disable charge tBAT_OVP_DGL | typ 1 us | 11 | |
| Typical Top-Off Timer Accuracy tTOP_OFF | TOP_OFF_TIMER = 30 min | min 24 · typ 30 · max 36 min | 11 |
| Charge Safety Timer Accuracy tSAFETY | CHG_TIMER = 12 hours | min 10.8 · typ 12 · max 13.2 hr | 11 |
| SCL clock frequency fSCL | max 1000 kHZ | 11 | |
| Data set-up time tSU_STA | min 10 ns | 11 | |
| Data hold time tHD_DAT | min 0 · max 70 ns | 11 | |
| Rise time of SDA signal trDA | min 10 · max 80 ns | 11 |
Pins, by the datasheet
24- 1 D–
- Negative USB data line for USB host/charging port detection, including data contact detection and BC1.2 secondary detection. · p. 4
- 2 STAT
- Charge status indicator; pull up through 10-kΩ. LOW indicates charging, HIGH indicates charge complete or disabled, and 1Hz blinking indicates a fault. · p. 4
- 3 CE
- Active low charge enable; charging requires EN_CHG = 1 and CE LOW. Internally pulled low through 900k-Ω. · p. 4
- 4 SDA
- I2C interface data; connect to the pull-up rail through a 10-kΩ resistor. · p. 4
- 5 SCL
- I2C interface clock; connect to the pull-up rail through a 10-kΩ resistor. · p. 4
- 6 INT
- Active interrupt output; pull up through 10-kΩ. Sends an active low 256-us pulse to report device status and faults. · p. 4
- 7 TS
- Temperature qualification input; connect an NTC thermistor and a REGN-to-TS-to-GND resistor divider. Charging suspends outside the programmed window; 103AT-2 is recommended. · p. 4
- 8 ILIM
- Sets and monitors maximum input current using a resistor to ground. If unused, connect to GND; do not float. · p. 5
- 9 PG
- Active low power-good indicator; connect to the pull-up rail through 10-kΩ. LOW indicates a good input source. · p. 5
- 10 NC
- Leave floating or tie to ground. · p. 5
- 11 REGN
- Bias supply for internal MOSFET drivers and IC; bypass to GND with 4.7-uF ceramic capacitance. Current limit is 50 mA. · p. 5
- 12 BTST
- PWM high-side driver supply connected internally to the bootstrap diode cathode; connect 47nF from SW to BTST. · p. 5
- 13 BAT
- Battery power connection; place at least 10-uF capacitance after derating close to BAT and GND. · p. 5
- 14 BAT
- Battery power connection; place at least 10-uF capacitance after derating close to BAT and GND. · p. 5
- 15 SYS
- System connection with internal BATFET to BAT; place 2x22-uF capacitance after derating close to SYS and PGND. · p. 5
- 16 SYS
- System connection with internal BATFET to BAT; place 2x22-uF capacitance after derating close to SYS and PGND. · p. 5
- 17 SW
- Connect to the switched side of the external inductor. · p. 5
- 18 SW
- Connect to the switched side of the external inductor. · p. 5
- 19 GND
- Ground return. · p. 5
- 20 GND
- Ground return. · p. 5
- 21 PMID
- Blocking MOSFET connection; total VBUS and PMID input low-ESR capacitance must be at least 10 uF after derating, with at least 1-uF at VBUS; typical PMID capacitance is 10 uF. · p. 5
- 22 PMID
- Blocking MOSFET connection; total VBUS and PMID input low-ESR capacitance must be at least 10 uF after derating, with at least 1-uF at VBUS; typical PMID capacitance is 10 uF. · p. 5
- 23 VBUS
- External DC input supply; bypass to GND with at least 1-uF ceramic capacitance close to the IC. · p. 5
- 24 D+
- Positive USB data line for USB host/charging port detection, including data contact detection and BC1.2 secondary detection. · p. 4
Ordering codes, by the datasheet
6- BQ25883RGER
- VQFN (RGE), 24 pins · 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 78
- BQ25883RGER.A
- VQFN (RGE), 24 pins · 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 78
- BQ25883RGERG4
- VQFN (RGE), 24 pins · 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 78
- BQ25883RGERG4.A
- VQFN (RGE), 24 pins · 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 78
- BQ25883RGET
- VQFN (RGE), 24 pins · 250 units, SMALL T&R; operating temperature -40 to 85 °C · p. 78
- BQ25883RGET.A
- VQFN (RGE), 24 pins · 250 units, SMALL T&R; operating temperature -40 to 85 °C · p. 78
Parts like it
8BQ25616RTW
QFN-24-EP(4x4)-40℃~+85℃ 1 3A 4.2V 4V~13.5V 9.5uA Charging IC Lithium Battery Support QFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24296MRGE
VQFN-24-EP(4x4)-40℃~+85℃ 1 15uA 2.4V 3.9V~6.2V 3A 4.2V Charging IC I2C Lithium Battery Support Support VQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24195LRGE
VQFN-24-EP(4x4)-40℃~+85℃ 1 2.5A 3.9V~17V 30uA 4.2V Charging IC I2C Lithium Battery Support Support VQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24295RGE
VQFN-24-EP(4x4)-40℃~+85℃ 1 2.5V 20uA 3.9V~6.2V 3A 4.2V Charging IC I2C Lithium Battery Support Support VQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24259RGE
VQFN-24-EP(4x4)-40℃~+85℃ 1 20uA 2A 3.9V~6.2V Charging IC I2C Lithium Battery Support Support VQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ25896RTW
QFN-24-EP(4x4)-40℃~+85℃ 1 12uA 3.9V~14V 3A 4.208V Charging IC I2C Support QFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24196RGE
VQFN-24-EP(4x4)-40℃~+85℃ 1 15uA 2.5A 3.9V~17V 4.208V Charging IC I2C Lithium Battery Support Support VQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24193RGE
VQFN-24-EP(4x4)-40℃~+85℃ 1 15uA 3.9V~17V 4.2V 4.5A Charging IC I2C Lithium Battery Support Support VQFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery Management
Questions
Is there a KiCad symbol and footprint for the BQ25883RGE?
Yes. The symbol is EasyEDA_Cloud:BQ25883RGER and the footprint EasyEDA_Cloud:VQFN-24_L4.0-W4.0-P0.50-TL-EP2.7, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the BQ25883RGE?
VQFN-24-EP(4x4), with 25 pins. Its footprint is drawn on this page.
Where is the BQ25883RGE datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the BQ25883RGE?
JLCPCB lists it as part C544362, with 1,015 in stock; the sellers' links on this page open their listings.
What can replace the BQ25883RGE?
Parts like it in the library: the BQ25616RTW by Texas Instruments, the BQ24296MRGE by Texas Instruments, the BQ24195LRGE by Texas Instruments and the BQ24295RGE by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.