Skip to the content
37

BQ25756RRVR

Texas InstrumentsExtended

-40℃~+125℃ 17uA 1~14 20A 4.2V~70V Charging IC I2C Lithium Battery、LiFePO4 Battery Support VQFN-36(5x6) Battery Management ROHS

Part id
ti/BQ25756RRVR
Category
Battery Management
Package
VQFN-36(5x6)
Pins
37
In stock
6,072 at JLCPCB (C19272232)
Used on
7 open-source boards

Overview

The BQ25756RRVR is a battery Management made by Texas Instruments in a VQFN-36(5x6) package with 37 pins. -40℃~+125℃ 17uA 1~14 20A 4.2V~70V Charging IC I2C Lithium Battery、LiFePO4 Battery Support VQFN-36(5x6) Battery Management ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:BQ25756RRVR, from EasyEDA) and its footprint (EasyEDA_Cloud:TQFN-36_L6.0-W5.0-P0.50-BL-EP-1, from EasyEDA), ready for a KiCad board. 6,072 are in stock at JLCPCB (part C19272232). 7 open-source boards in 6 repositories on GitHub use it.

Symbol

1SCL2SDA3INT#4STAT15STAT26PG#7CE#8TS9ICHG10ILIM_HIZ11FBG12FB13SRN14SRP15NC16NC17PGND18SW219HIDRV220BTST221LODRV222PGND23DRV_SUP24REGN25LODRV126BTST127HIDRV128SW129ACN30ACP31NC32VAC33VAC34ACUV35ACOV36FSW_SYNC37PGND
EasyEDA_Cloud:BQ25756RRVRFrom EasyEDA

Footprint

37
EasyEDA_Cloud:TQFN-36_L6.0-W5.0-P0.50-BL-EP-1From EasyEDA

From the datasheet

19
Supply, least
4.2 V · VAC, recommended operating min · p. 7
Supply, most
70 V · VAC, recommended operating max · p. 7
Supply, least
4 V · DRV_SUP, recommended direct drive min · p. 7
Supply, most
12 V · DRV_SUP, recommended direct drive max · p. 7
Supply, absolute maximum
85 V · VAC, absolute max · p. 7
Supply, absolute maximum
14 V · DRV_SUP, absolute max · p. 7
Works from
-40 °C · Ambient temperature min · p. 7
Works up to
105 °C · Ambient temperature max · p. 7
Junction, hottest
150 °C · Junction temperature absolute max · p. 7
Takes working
750 µA · VAC quiescent input current typical, not switching · p. 9
Takes asleep
17 µA · Battery quiescent current typical, BATFET on, ADC disabled, VAC = 0 V · p. 9
A pin gives at most
5 mA · CE, PG, STAT1, STAT2 output sink current absolute max · p. 7
Feedback reference
1.536 V · Feedback voltage typical, VFB_REG = 0x10 · p. 9
Junction to air (RRV)
29.4 K/W · Junction-to-ambient thermal resistance · p. 8
Junction to case (RRV)
18.8 K/W · Junction-to-case top thermal resistance · p. 8
Junction to board (RRV)
9.9 K/W · Junction-to-board thermal resistance · p. 8
Supply, least
4.5 V · DRV_SUP, external gate drive supply minimum · p. 22
Switches at
250 kHz · typical, RFSW_SYNC = 133kΩ · p. 13
Switches at
500 kHz · typical, RFSW_SYNC = 50kΩ · p. 13

What it is and has

25
Control
Standalone or I2C controlled, bidirectional buck-boost battery charging · p. 1
Li-ion cells
1 to 14 · p. 1
LiFePO4 cells
1 to 16 · p. 1
Converter
Synchronous buck-boost charge controller with NFET drivers · p. 1
Switching frequency
Adjustable, 200kHz to 600kHz · p. 1
Synchronization
External clock synchronization selectable · p. 1
Loop compensation
Integrated, with soft start · p. 1
MPPT
Automatic maximum power point tracking for solar charging · p. 1
Buck-only mode
Supported · p. 1
Charge voltage accuracy
±0.5% · p. 1
Charge current accuracy
±3% · p. 1
ADC
16-bit; voltage, current and temperature monitoring · p. 1
Protection
Adjustable input overvoltage and undervoltage · p. 1
Protection
Battery overvoltage and overcurrent · p. 1
Protection
Charge safety timer · p. 1
Protection
Battery short circuit · p. 1
Protection
Thermal shutdown · p. 1
Package
36-pin 5mm × 6mm QFN · p. 1
Battery chemistry
Li-Ion, Li-polymer, LiFePO4 · p. 19
Li-ion cell count
1 to 14 · p. 1
LiFePO4 cell count
1 to 16 · p. 1
Charging control
I2C host control or autonomous charging with resistor programmable limits · p. 19
ADC
16-bit; monitors input current, charge current and input/battery/thermistor voltages · p. 19
Package
36-pin 5-mm × 6-mm QFN, 0.5-mm pin pitch · p. 19
Switching frequency
200 kHz to 600 kHz, resistor programmable · p. 23

Around it

26
res 10-kΩ
between SCL and logic rail; I2C clock pull-up. · p. 4
res 10-kΩ
between SDA and logic rail; I2C data pull-up. · p. 4
res 10-kΩ
between INT and logic rail; Interrupt pull-up. · p. 4
res 10-kΩ
between STAT1 and pull up rail; Charge status pull-up. · p. 4
res 10-kΩ
between PG and pull up rail; Power good pull-up. · p. 4
other 103AT-2 10-kΩ
between TS and PGND; Recommended NTC thermistor; use a resistor divider from REGN to TS to PGND. · p. 5
cap 0.47-μF
between SRN and SRP; Ceramic differential-mode filtering capacitor. · p. 5
cap 0.1-μF
between SRN and PGND; Optional ceramic common-mode filtering capacitor. · p. 5
cap 0.1-μF
between SRP and PGND; Ceramic common-mode filtering capacitor. · p. 5
cap 4.7-μF
between DRV_SUP and PGND; Ceramic gate drive supply capacitor. · p. 5
cap 4.7-μF
between REGN and PGND; Ceramic internal regulator output capacitor. · p. 5
cap 0.47-μF
between ACN and ACP; Ceramic differential-mode filtering capacitor. · p. 6
cap 0.1-μF
between ACN and PGND; Optional ceramic common-mode filtering capacitor. · p. 6
cap 0.1-μF
between ACP and PGND; Ceramic common-mode filtering capacitor. · p. 6
cap 1-µF
between VAC and PGND; Input voltage detection and power bypass capacitor. · p. 6
res 200 kΩ
between FSW_SYNC and PGND; RFSW option for 200 kHz; the pin must not float. · p. 23
res 133 kΩ
between FSW_SYNC and PGND; RFSW option for 250 kHz. · p. 23
res 100 kΩ
between FSW_SYNC and PGND; RFSW option for 300 kHz. · p. 23
res 80 kΩ
between FSW_SYNC and PGND; RFSW option for 350 kHz. · p. 23
res 66.67 kΩ
between FSW_SYNC and PGND; RFSW option for 400 kHz. · p. 23
res 57.1 kΩ
between FSW_SYNC and PGND; RFSW option for 450 kHz. · p. 23
res 50 kΩ
between FSW_SYNC and PGND; RFSW option for 500 kHz. · p. 23
res 44.4 kΩ
between FSW_SYNC and PGND; RFSW option for 550 kHz. · p. 23
res 40 kΩ
between FSW_SYNC and PGND; RFSW option for 600 kHz. · p. 23
res 10-kΩ
between ICHG and PGND; Example charge current programming resistor. · p. 25
res 5-kΩ
between ILIM_HIZ and PGND; Example hardware input current limit of 10 A with KILIM = 50 A-kΩ. · p. 30

Specifications

152
ParameterConditionsAs printedPage
VoltageVAC, ACUV, ACOV, ACP, ACN, SRP, SRN, FB, FBGmin -0.3 · max 85 V7
VoltageSW1, SW2min -2 · max 85 V7
VoltageSW1, SW2 (40ns transient)min -4 · max 85 V7
VoltagePGmin -0.3 · max 40 V7
VoltageBTST1, HIDRV1 with respect to SW1min -0.3 · max 14 V7
VoltageBTST2, HIDRV2 with respect to SW2min -0.3 · max 14 V7
VoltageDRV_SUP, LODRV1, LODRV2min -0.3 · max 14 V7
VoltageACP with respect to ACN, SRP with respect to SRNmin -0.3 · max 0.3 V7
VoltageCE, FSW_SYNC, ICHG, ILIM_HIZ, INT, REGN, SCL, SDA, MODE, STAT1, STAT2, TSmin -0.3 · max 6 V7
Output Sink CurrentCE, PG, STAT1, STAT2max 5 mA7
Junction temperature TJmin -40 · max 150 °C7
Storage temperature Tstgmin -65 · max 150 °C7
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pinsmin -2000 · max 2000 V7
Electrostatic discharge V(ESD)Charged device model (CDM), per ANSI/ESDA/JEDEC JS-002, all pinsmin -500 · max 500 V7
Input voltage VACmin 4.2 · max 70 V7
Battery voltage VBATmin 0 · max 70 V7
DRV_SUP pin direct drive voltage range VDRV_SUPmin 4 · max 12 V7
Switching Frequency FSWmin 200 · max 600 kHz7
Junction temperature TJmin -40 · max 125 °C7
Ambient temperature TAmin -40 · max 105 °C7
VAC capacitor CVACmin 1 uF7
Buck-boost input capacitance (minimum value after derating) CINmin 160 uF7
Buck-boost output capacitance (minimum value after derating) COUTmin 160 uF7
REGN capacitor (nominal value before derating) CREGNmin 4.7 uF7
DRV_SUP capacitor (nominal value before derating) CDRV_SUPmin 4.7 uF7
Switched Inductor Lmin 2.2 · max 15 uH7
Inductor DC resistance RDCRmin 1.75 · max 60 mΩ7
Input current sense resistor RAC_SNS0mΩ disables input current limitmin 0 · typ 5 · max 10 mΩ8
Battery current sense resistor RBAT_SNStyp 5 mΩ8
ICHG programming pulldown resistor RICHGPulled to GND disables hardware charge current limitmin 0 · max 100 kΩ8
ILIM_HIZ programming pulldown resistor RILIM_HIZPulled to GND disables hardware input current limitmin 0 · max 50 kΩ8
Junction-to-ambient thermal resistance (JEDEC(1)) RθJABQ25756, RRV, 36 PINStyp 29.4 °C/W8
Junction-to-case (top) thermal resistance RθJC(top)BQ25756, RRV, 36 PINStyp 18.8 °C/W8
Junction-to-board thermal resistance RθJBBQ25756, RRV, 36 PINStyp 9.9 °C/W8
Junction-to-top characterization parameter ΨJTBQ25756, RRV, 36 PINStyp 0.2 °C/W8
Junction-to-board characterization parameter ΨJBBQ25756, RRV, 36 PINStyp 9.8 °C/W8
Junction-to-case (bottom) thermal resistance RθJC(bot)BQ25756, RRV, 36 PINStyp 2.5 °C/W8
Quiescent battery current with BATFET on (ISRN + ISRP) IQ_BATVBAT = 28V, VAC = 0V, ADC_EN = 0, TJ < 105 °Ctyp 17 uA9
Quiescent battery current with BATFET on (ISRN + ISRP) IQ_BATVBAT = 28V, VAC = 0V, ADC_EN = 1, TJ < 105 °Ctyp 500 · max 700 uA9
Quiescent input current (IVAC) IQ_VACNot switchingtyp 0.75 · max 1 mA9
Quiescent battery current in Reverse mode (ISRN + ISRP) IQ_REVNot switchingtyp 0.75 · max 1 mA9
VAC operating range VVAC_OPmin 4.2 · max 70 V9
VAC converter enable threshold VVAC_OKVAC rising, no batterymin 4.2 V9
VAC converter disable threshold VVAC_OKZVAC falling, no batterymax 3.5 V9
ACUV comparator threshold to enter VAC_UVP VREF_ACUVVACUV fallingmin 1.095 · typ 1.1 · max 1.106 V9
ACUV comparator threshold hysteresis VREF_ACUV_HYSVACUV risingtyp 50 mV9
VAC internal threshold to enter VAC_OVP VVAC_INT_OVIN risingmin 72 · typ 74 · max 76 V9
VAC internal thresholds to exit VAC_OVP VVAC_INT_OVZIN fallingmin 69 · typ 71 · max 73 V9
ACOV comparator threshold to enter VAC_OVP VREF_ACOVVACOV risingmin 1.184 · typ 1.2 · max 1.206 V9
ACOV comparator threshold hysteresis VREF_ACOV_HYSVACOV fallingtyp 50 mV9
Feedback voltage range VVFB_RANGEmin 1.504 · max 1.566 V9
Nominal feedback voltage VVFB_NOMVFB_REG = 0x10typ 1.536 V9
Feedback voltage regulation accuracy VVFB_ACCTJ = 0°C to 85°Cmin -0.5 · max 0.5 %9
Feedback voltage regulation accuracy VVFB_ACCTJ = -40°C to 125°Cmin -0.7 · max 0.7 %9
FBG resistance to PGND RFBGIFBG = 1mAtyp 33 · max 55 Ω9
Charge current regulation range ICHG_REG_RANGEmin 0.4 · max 20 A9
I2C setting charge current regulation accuracy ICHG_REG_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V, 55V; ICHG_REG = 0x012C; 15 Amin -3 · max 3 %9
I2C setting charge current regulation accuracy ICHG_REG_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V, 55V; ICHG_REG = 0x0064; 5 Amin -3 · max 3 %9
I2C setting charge current regulation accuracy ICHG_REG_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V, 55V; ICHG_REG = 0x0028; 2 Amin -5 · max 5 %9
Hardware charge current limit set factor (Amperes of charge current per kΩ on ICHG pin) KICHGRBAT_SNS = 5mΩ, RICHG = 10kΩ, 5kΩ, and 3.33kΩmin 48 · typ 50 · max 52 Ax kΩ9
ICHG pin voltage when ICHG pin is in regulation VREF_ICHGtyp 2 V9
Precharge current regulation range IPRECHG_RANGEVFB < VBAT_LOWV * VVFB_REGmin 0.25 · max 10 A9
I2C setting precharge current accuracy IPRECHG_ACCRBAT_SNS = 5mΩ, VFB < VBAT_LOWV * VVFB_REG. IPRECHG = 0x003C; 3.0 Amin -4 · max 4 %10
I2C setting precharge current accuracy IPRECHG_ACCRBAT_SNS = 5mΩ, VFB < VBAT_LOWV * VVFB_REG. IPRECHG[1:0] = 0x0014; 1.0 Amin -10 · max 10 %10
I2C setting precharge current accuracy IPRECHG_ACCRBAT_SNS = 5mΩ, VFB < VBAT_LOWV * VVFB_REG. IPRECHG[1:0] = 0x000A; 0.50 Amin -30 · max 30 %10
Termination current range ITERM_RANGEVFB = VVFB_REGmin 0.25 · max 10 A10
Termination current accuracy ITERM_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V, 55V. ITERM = 0x001E; 1.5 Amin -7 · max 7 %10
Termination current accuracy ITERM_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V, 55V. ITERM = 0x000A; 0.50 Amin -20 · max 20 %10
Termination current accuracy ITERM_ACCRBAT_SNS = 5mΩ, VBAT = 12V, 36V, 55V. ITERM = 0x0005; 0.250 Amin -50 · max 50 %10
Trickle charge to pre-charge transition VBAT_SHORTVSRN risingmin 2.8 · typ 3 · max 3.2 V10
Pre-charge to trickle charge transition VBAT_SHORTVSRN fallingmin 2.2 · typ 2.4 · max 2.6 V10
Pre-charge to fast-charge transition VBAT_LOWVVFB rising, as percentage of VFB_REG, VBAT_LOWV[2:0] = 3min 69 · typ 71.7 · max 73.8 %10
Pre-charge to fast-charge transition VBAT_LOWVVFB rising, as percentage of VFB_REG, VBAT_LOWV[2:0] = 2min 64.3 · typ 66.7 · max 69 %10
Pre-charge to fast-charge transition VBAT_LOWVVFB rising, as percentage of VFB_REG, VBAT_LOWV[2:0] = 1min 52 · typ 55 · max 58 %10
Pre-charge to fast-charge transition VBAT_LOWVVFB rising, as percentage of VFB_REG, VBAT_LOWV[2:0] = 0min 27 · typ 30 · max 33 %10
BAT_LOWV hysteresis VBAT_LOWV_HYStyp 5 %10
Battery recharge threshold for Li-Ion and LiFePO4 VRECHGVFB falling, as percentage of VFB_REG, VRECHG[1:0] = 3typ 97.6 %10
Battery recharge threshold for Li-Ion and LiFePO4 VRECHGVFB falling, as percentage of VFB_REG, VRECHG[1:0] = 2typ 95.2 %10
Battery recharge threshold for Li-Ion and LiFePO4 VRECHGVFB falling, as percentage of VFB_REG, VRECHG[1:0] = 1typ 94.3 %10
Battery recharge threshold for Li-Ion and LiFePO4 VRECHGVFB falling, as percentage of VFB_REG, VRECHG[1:0] = 0typ 93 %10
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x00A0; 20 Amin -3 · max 3 %10
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x0050; 10 Amin -4 · max 4 %10
I2C setting input current regulation accuracy in forward mode IIREG_DPM_ACCRAC_SNS = 2mΩ, IAC_DPM = 0x0028; 5.0 Amin -7 · max 7 %10
Hardware input current limit set factor (Amperes of input current per kΩ on ILIM_HIZ pin) KILIMRAC_SNS = 2mΩ, RILIM = 5kΩ, 2.5kΩ, and 1.67kΩmin 48 · typ 50 · max 52 Ax kΩ10
ILIM_HIZ pin voltage when ILIM_HIZ pin is in regulation VREF_ILIM_HIZtyp 2 V10
TS pin voltage rising T5 threshold. Charge back to ICHG and reduced VFB_REG above this voltage. VT5_RISEAs Percentage to REGN, TS_T5=60°C w/ 103ATmin 35 · typ 35.5 · max 36 %12
TS pin voltage rising TCOLD threshold. Reverse mode suspended above this voltage VBCOLD_RISEAs Percentage to REGN (BCOLD = –20°C w/ 103AT)min 79.45 · typ 80 · max 80.55 %12
TS pin voltage rising TCOLD threshold. Reverse mode suspended above this voltage VBCOLD_RISEAs Percentage to REGN (BCOLD = –10°C w/ 103AT)min 76.65 · typ 77.15 · max 77.65 %12
TCOLD comparator falling threshold. VBCOLD_FALLAs Percentage to REGN (–20°C w/ 103AT)min 78.2 · typ 78.7 · max 79.2 %12
TCOLD comparator falling threshold. VBCOLD_FALLAs Percentage to REGN (–10°C w/ 103AT)min 75.5 · typ 75.6 · max 76.5 %12
TS pin voltage falling THOT threshold. Reverse mode suspends below this voltage VBHOT_FALLAs Percentage to REGN, (BHOT = 55°C w/ 103AT)min 37.2 · typ 37.7 · max 38.2 %12
TS pin voltage falling THOT threshold. Reverse mode suspends below this voltage VBHOT_FALLAs Percentage to REGN, (BHOT = 60°C w/ 103AT)min 33.875 · typ 34.375 · max 34.875 %12
TS pin voltage falling THOT threshold. Reverse mode suspends below this voltage VBHOT_FALLAs Percentage to REGN, (BHOT 65°C w/ 103AT)min 30.75 · typ 31.25 · max 31.75 %12
TS pin voltage rising THOT threshold. Reverse mode allowed above this voltage VBHOT_RISEAs Percentage to REGN, (BHOT = 55°C w/ 103AT)min 38.5 · typ 39 · max 39.95 %12
TS pin voltage rising THOT threshold. Reverse mode allowed above this voltage VBHOT_RISEAs Percentage to REGN, (BHOT = 60°C w/ 103AT)min 35 · typ 35.5 · max 36 %12
TS pin voltage rising THOT threshold. Reverse mode allowed above this voltage VBHOT_RISEAs Percentage to REGN, (BHOT 65°C w/ 103AT)min 32 · typ 32.5 · max 33 %12
Battery overvoltage threshold VBAT_OVVFB rising, as percentage of VFB_REGmin 102.5 · typ 104 · max 105.5 %12
Battery overvoltage falling threshold VBAT_OVZVFB falling, as percentage of VFB_REGmin 100.5 · typ 102 · max 103.5 %12
Battery charge over-current threshold VICHG_OCVSRP - VSRN risingmin 120 · max 170 mV12
Thermal shutdown rising threshold TSHUTTemperature increasingtyp 150 °C12
Thermal shutdown falling threshold TSHUTTemperature decreasingtyp 135 °C12
REGN LDO output voltage VREGNIREGN = 20mAmin 4.8 · typ 5 · max 5.2 V12
REGN LDO output voltage VREGNVAC = 5V, IREGN = 20mAmin 4.35 · typ 4.6 V12
REGN LDO current limit IREGNVREGN = 4.5Vmin 70 mA12
REGN OK threshold to allow switching VREGN_OKREGN risingtyp 3.55 V12
DRV_SUP under-voltage threshold to allow switching VDRV_UVPZDRV_SUP risingmax 3.7 V12
DRV_SUP over-voltage threshold to disable switching VDRV_OVPDRV_SUP risingmin 12.8 · typ 13.2 · max 13.6 V12
VAC discharge load current IAC_LOADmin 16 mA12
Battery (SRN) discharge load current IBAT_LOADmin 16 mA12
Switching Frequency fSWRFSW_SYNC = 133kΩmin 212 · typ 250 · max 288 kHz13
Switching Frequency fSWRFSW_SYNC = 50kΩmin 425 · typ 500 · max 575 kHz13
FSW_SYNC input high threshold VIH_SYNCmin 1.3 V13
FSW_SYNC input low threshold VIL_SYNCmax 0.4 V13
FSW_SYNC input pulse width PWSYNCmin 80 ns13
Buck side high-side turnon resistance RHIDRV1_ONVBTST1 - VSW1 = 5Vtyp 3.4 Ω13
Buck side high-side turnoff resistance RHIDRV1_OFFVBTST1 - VSW1 = 5Vtyp 1 Ω13
Bootstrap refresh comparator threshold voltage VBTST1_REFRESHBTST1 falling, VBTST1 - VSW1 when low-side refresh pulse is requestedmin 2.7 · typ 3.1 · max 3.9 V13
Buck side low-side turnon resistance RLODRV1_ONVREGN = 5Vtyp 3.4 Ω13
Buck side low-side turnoff resistance RLODRV1_OFFVREGN = 5Vtyp 1 Ω13
Buck side dead time, both edges tDT1typ 45 ns13
Boost side high-side turnon resistance RHIDRV2_ONVBTST2 - VSW2 = 5Vtyp 3.4 Ω13
Boost side high-side turnoff resistance RHIDRV2_OFFVBTST2 - VSW2 = 5Vtyp 1 Ω13
Bootstrap refresh comparator threshold voltage VBTST2_REFRESHBTST2 falling, VBTST2 - VSW2 when low-side refresh pulse is requestedmin 2.7 · typ 3.1 · max 3.9 V13
Boost side low-side turnon resistance RLODRV2_ONVREGN = 5Vtyp 3.4 Ω13
Boost side low-side turnoff resistance RLODRV2_OFFVREGN = 5Vtyp 1 Ω13
Boost side dead time, both edges tDT2typ 45 ns13
Conversion-time, each measurement tADC_CONVADC_SAMPLE[1:0] = 00typ 24 ms13
Conversion-time, each measurement tADC_CONVADC_SAMPLE[1:0] = 01typ 12 ms13
Conversion-time, each measurement tADC_CONVADC_SAMPLE[1:0] = 10typ 6 ms13
Effective resolution ADCRESADC_SAMPLE[1:0] = 00min 14 · typ 15 bits13
Effective resolution ADCRESADC_SAMPLE[1:0] = 01min 13 · typ 14 bits13
Effective resolution ADCRESADC_SAMPLE[1:0] = 10min 12 · typ 13 bits13
Input current ADC reading (positive or negative) IAC_ADCRange with 2mΩ RAC_SNSmin -50000 · max 50000 mA13
Input current ADC reading (positive or negative) IAC_ADCLSB with 2mΩ RAC_SNStyp 2 mA13
Battery current ADC reading (positive or negative) IBAT_ADCRange with 5mΩ RBAT_SNSmin -20000 · max 20000 mA13
Battery current ADC reading (positive or negative) IBAT_ADCLSB with 5mΩ RBAT_SNStyp 2 mA13
Input voltage ADC reading VAC_ADCRangemin 0 · max 65534 mV13
Input voltage ADC reading VAC_ADCLSBtyp 2 mV13
Battery voltage ADC reading VBAT_ADCRangemin 0 · max 65534 mV13
Battery voltage ADC reading VBAT_ADCLSBtyp 2 mV13
TS voltage ADC reading, as percentage of REGN TSADCRangemin 0 · max 99.9 %13
TS voltage ADC reading, as percentage of REGN TSADCLSBtyp 0.098 %13
FB voltage ADC reading VFB_ADCRangemin 0 · max 2047 mV13
FB voltage ADC reading VFB_ADCLSBtyp 1 mV13
Input high threshold level VIHI2C INTERFACE (SCL, SDA)min 1.3 V14
Input low threshold level VILI2C INTERFACE (SCL, SDA)max 0.4 V14
Output low threshold level VOLI2C INTERFACE (SCL, SDA); Sink current = 5mAmax 0.4 V14
High-level leakage current IIN_BIASI2C INTERFACE (SCL, SDA); Pull up rail 3.3Vmax 1 uA14
Input high threshold level (CE) VIHLOGIC I/O PIN (CE, PG , STAT1, STAT2)min 1.3 V14
Output low threshold level (CE, PG, STAT1, STAT2) VOLSink current = 5mAmax 0.4 V14
Input low threshold level (CE) VILLOGIC I/O PIN (CE, PG , STAT1, STAT2)max 0.4 V14
High-level leakage current (CE, PG, STAT1, STAT2) IOUT_BIASPull up rail 3.3Vmax 1 uA14

Pins, by the datasheet

37
1 SCL
I2C clock; connect to the logic rail through a 10-kΩ resistor. · p. 4
2 SDA
I2C data; connect to the logic rail through a 10-kΩ resistor. · p. 4
3 INT
Active-low interrupt output with a 256-us pulse reporting status and faults; pull up through 10-kΩ. · p. 4
4 STAT1
Charge status 1 output; pull up through 10-kΩ; may serve as a general purpose indicator when its status function is disabled. · p. 4
5 STAT2
Charge status 2 output; pull up through 10-kΩ; may serve as a general purpose indicator when its status function is disabled. · p. 4
6 PG
Active-low power good output; pull up through 10-kΩ; indicates VAC is within the programmed operating window and may serve as a general purpose indicator. · p. 4
7 CE
Active-low charge enable; must be pulled HIGH or LOW; may serve as a general purpose indicator when its enable function is disabled. · p. 4
8 TS
Thermistor qualification input; connect an NTC thermistor and a divider from REGN to PGND; out-of-range voltage suspends charging. · p. 5
9 ICHG
Charge current limit setting and monitoring; connect a programming resistor to PGND, or pull to PGND if unused. · p. 5
10 ILIM_HIZ
Input current limit setting and monitoring; pull HIGH for HIZ mode; connect a programming resistor to PGND, or pull to PGND if unused. · p. 5
11 FBG
Battery feedback divider return; driven to PGND while charging and high impedance outside the input operating window. · p. 5
12 FB
Battery charge voltage feedback; connect the output of a resistive divider from the battery terminals. · p. 5
13 SRN
Negative charge current sense input; connect 0.47-uF to SRP and optionally 0.1-uF to PGND. · p. 5
14 SRP
Positive charge current sense input; connect 0.47-uF to SRN and 0.1-uF to PGND. · p. 5
15 NC
Leave floating; do not tie to PGND. · p. 5
16 NC
Leave floating; do not tie to PGND. · p. 5
17 PGND
Tie directly to PGND. · p. 5
18 SW2
Boost half bridge switching node; connect to boost high-side FET source, low-side FET drain, and the inductor to SW1. · p. 5
19 HIDRV2
Boost high-side N-channel MOSFET gate driver. · p. 5
20 BTST2
Boost high-side gate driver supply; connect a capacitor to SW2. · p. 5
21 LODRV2
Boost low-side N-channel MOSFET gate driver. · p. 5
22 PGND
High-current power ground return for low-side gate drivers. · p. 5
23 DRV_SUP
Gate drive supply; connect 4.7-uF ceramic to power ground; may connect to REGN or an external supply up to 12 V. · p. 5
24 REGN
Internal linear regulator output; connect 4.7-uF ceramic to power ground; may supply DRV_SUP. · p. 5
25 LODRV1
Buck low-side N-channel MOSFET gate driver. · p. 5
26 BTST1
Buck high-side gate driver supply; connect a capacitor to SW1. · p. 5
27 HIDRV1
Buck high-side N-channel MOSFET gate driver. · p. 5
28 SW1
Buck half bridge switching node; connect to buck high-side FET source, low-side FET drain, and the inductor to SW2. · p. 5
29 ACN
Negative adapter current sense input; connect 0.47-uF to ACP and optionally 0.1-uF to PGND. · p. 6
30 ACP
Positive adapter current sense input; connect 0.47-uF to ACN and 0.1-uF to PGND. · p. 6
31 NC
Leave floating; do not tie to PGND. · p. 6
32 VAC
Input voltage detection; connect a 1-uF capacitor to PGND; regulated to VAC_REV in reverse mode. · p. 6
33 VAC
Input bias powering the IC; connect a 1-uF capacitor to PGND and reference the ACOV/ACUV divider to this pin. · p. 6
34 ACUV
Input undervoltage comparator and input voltage regulation setting; connect a divider from VAC to PGND, or pull to VAC if unused. · p. 6
35 ACOV
Input overvoltage comparator; connect a divider from VAC to PGND, or pull to PGND if unused. · p. 6
36 FSW_SYNC
Switching frequency setting through a resistor to PGND, or external clock synchronization from 200-kHz to 600-kHz. · p. 6
37 Thermal Pad
Solder exposed pad to the board with vias star-connecting to PGND and the ground plane for heat dissipation. · p. 6

Open-source boards using it

7
  • 4 layers180 × 170 mmHw openmower yardforce, the printed circuit board in 3D

    Hw openmower yardforce

    xtech/hw-openmower-yardforce

    This repository contains the design files for a custom mainboard specifically designed for converting YardForce mowers to OpenMower

    293 parts12CC-BY-4.0
  • 4 layers103.1 × 71.1 mmBms, the printed circuit board in 3D

    Bms

    membaye/bms

    BMS V1

    236 parts1
  • 6 layers196 × 115 mmMonolithDev, the printed circuit board in 3D

    MonolithDev

    MidwestMotorBoy/Battery-Bank

    Monolith: an ultralight IP67 power bank for backpacking. 4S BAK 65E 21700 (91 Wh, under the 100 Wh airline limit), two bidirectional 100 W USB-C PD ports, Bluetooth LE (TI CC2340) with an iPhone app.

    430 parts
  • 4 layers100 × 55 mmPMP41115, the printed circuit board in 3D

    PMP41115

    Tim4769/usb-c-pd31-epr-charger

    KiCad hardware, firmware artifacts, and validation notes for a bidirectional USB-C PD 3.1 EPR buck-boost charger targeting 240 W.

    158 parts
  • 4 layers100 × 65 mmHw charger, the printed circuit board in 3D

    Hw charger

    xtech/hw-module-charger

    This hardware version is in beta state. Expect for things to not work at the current state!

    164 parts
  • 6 layers43.2 × 74.4 mmMonolith, the printed circuit board in 3D

    Monolith

    MidwestMotorBoy/Battery-Bank

    Monolith: an ultralight IP67 power bank for backpacking. 4S BAK 65E 21700 (91 Wh, under the 100 Wh airline limit), two bidirectional 100 W USB-C PD ports, Bluetooth LE (TI CC2340) with an iPhone app.

    289 parts
  • 2 layers99.5 × 99.5 mmCharge Controller, the printed circuit board in 3D

    Charge Controller

    UWCubeSat/BMS-EPS-HS2

    Repository of the HS-2 Battery Management System

    55 parts

Parts like it

3

Questions

Is there a KiCad symbol and footprint for the BQ25756RRVR?

Yes. The symbol is EasyEDA_Cloud:BQ25756RRVR and the footprint EasyEDA_Cloud:TQFN-36_L6.0-W5.0-P0.50-BL-EP-1, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the BQ25756RRVR?

VQFN-36(5x6), with 37 pins. Its footprint is drawn on this page.

Where is the BQ25756RRVR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the BQ25756RRVR?

JLCPCB lists it as part C19272232, with 6,072 in stock; the sellers' links on this page open their listings.

What can replace the BQ25756RRVR?

Parts like it in the library: the BQ25820RRVR by Texas Instruments, the B25858BQWRRVRQ1 by Texas Instruments and the BQ25751RRVR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the BQ25756RRVR?

7 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.