Skip to the content
9

BQ25170DSG

Texas InstrumentsExtended

-40℃~+125℃ 1 350nA 6.6V 800mA Charging IC Lithium Battery、LiFePO4 Battery Support 恒流充电、恒压充电、涓流充电、自动再充电、充电终止、可编程充电电流、欠压锁定、Overcurrent Protection、Short-Circuit Protection、过压保护 WSON-8(2x2) Battery Management ROHS

Part id
ti/BQ25170DSG
Category
Battery Management
Package
WSON-8(2x2)
Pins
9
In stock
1,046 at JLCPCB (C5208201)
Used on
3 open-source boards

Overview

The BQ25170DSG is a battery Management made by Texas Instruments in a WSON-8(2x2) package with 9 pins. -40℃~+125℃ 1 350nA 6.6V 800mA Charging IC Lithium Battery、LiFePO4 Battery Support 恒流充电、恒压充电、涓流充电、自动再充电、充电终止、可编程充电电流、欠压锁定、Overcurrent Protection、Short-Circuit Protection、过压保护 WSON-8(2x2) Battery Management ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:BQ25170JDSGR, from EasyEDA) and its footprint (EasyEDA_Cloud:WSON-8_L2.0-W2.0-P0.50-TL-EP, from EasyEDA), ready for a KiCad board. 1,046 are in stock at JLCPCB (part C5208201). 3 open-source boards in 2 repositories on GitHub use it.

Symbol

1IN2ISET3TS4GND5STAT6PG#7VSET8OUT9EP
EasyEDA_Cloud:BQ25170JDSGRFrom EasyEDA

Footprint

9
EasyEDA_Cloud:WSON-8_L2.0-W2.0-P0.50-TL-EPFrom EasyEDA

From the datasheet

16
Supply, least
3 V · IN, recommended operating min · p. 4
Supply, most
6.6 V · IN, recommended operating max · p. 4
Supply, absolute maximum
30 V · IN, absolute maximum · p. 4
Junction, hottest
150 °C · Junction temperature, absolute maximum · p. 4
Takes working
450 µA · IN, typical quiescent current; 5 V input, 3.8 V output, charge enabled · p. 6
Takes asleep
350 nA · OUT, typical battery leakage; charge disabled, TJ = 25 °C · p. 6
Takes asleep
80 µA · IN, typical shutdown current; 5 V, charge disabled via TS, no battery · p. 6
Takes asleep
190 µA · IN, typical standby current; 5 V, charge terminated · p. 6
Gives
800 mA · OUT, recommended continuous output max · p. 4
Current limit
1 A · OUT, typical overcurrent limit threshold, current rising · p. 7
A pin gives at most
5 mA · PG, STAT, absolute maximum sink current per pin · p. 4
Dropout
425 mV · Typical dropout; VIN falling, VOUT = 4.35 V, IOUT = 500 mA · p. 6
Junction to air (DSG)
37 K/W · Junction-to-ambient, EVM · p. 5
Junction to air (DSG)
75.2 K/W · Junction-to-ambient, JEDEC · p. 5
Junction to case (DSG)
93.4 K/W · Junction-to-case, top · p. 5
Junction to board (DSG)
41.8 K/W · Junction-to-board thermal resistance · p. 5

What it is and has

16
Battery chemistry
Single-cell Li-Ion, Li-Polymer, and LiFePO4 · p. 11
Charge current programming
10mA to 800mA via ISET · p. 1
Charge voltage accuracy
±0.5% · p. 1
Charge current accuracy
±10% · p. 1
Precharge current
20% ISET · p. 1
Termination current
10% ISET · p. 1
Battery temperature monitoring
NTC thermistor input · p. 1
Input overvoltage protection
6.6V · p. 1
Output overvoltage protection
Based on VSET · p. 1
Overcurrent protection
1000mA · p. 1
Thermal protection
125°C thermal regulation; 150°C thermal shutdown · p. 1
Short circuit protection
OUT · p. 1
Configuration pin protection
VSET and ISET short/open protection · p. 1
Package
WSON (8), 2.0mm x 2.0mm · p. 1
Battery compatibility
Single-cell lithium-ion and lithium iron phosphate · p. 1
Programmable charging current
10mA to 800mA · p. 1

Around it

9
cap 1-μF
between IN and GND; Minimum capacitance; place close to the IC. · p. 3
cap 1-μF
between OUT and GND; Minimum capacitance; place close to the IC. · p. 3
res 10-kΩ
between STAT and pull-up rail; Status output pull-up. · p. 3
res 10-kΩ
between PG and pull-up rail; Power-good output pull-up. · p. 3
res 10-kΩ
between TS and GND; Use when TS temperature qualification is not needed. · p. 3
res 18 kΩ to 100 kΩ
between VSET and GND; Regulation voltage programming resistor; ±1% tolerance and <200 ppm/ºC temperature coefficient recommended. · p. 3
res 30 kΩ (10 mA) to 375 Ω (800 mA)
between ISET and GND; Fast-charge current programming; ICHG = KISET / RISET. · p. 3
res 604-Ω
between ISET and GND; 1% resistor for the Li-Ion example; expected charge current 497 mA. · p. 20
other 10-kΩ NTC (103AT)
between TS and GND; Battery temperature sensing thermistor in the Li-Ion design example. · p. 20

Specifications

91
ParameterConditionsAs printedPage
VoltageIN; over operating free-air temperature rangemin -0.3 · max 30 V4
VoltageOUT; over operating free-air temperature rangemin -0.3 · max 13 V4
VoltageISET, PG, STAT, TS, VSET; over operating free-air temperature rangemin -0.3 · max 5.5 V4
Output Sink CurrentPG, STATmax 5 mA4
Junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pinsmin -2500 · max 2500 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pinsmin -1500 · max 1500 V4
Input voltage VINmin 3 · max 6.6 V4
Output voltage VOUTmax 4.4 V4
Output current IOUTmax 0.8 A4
Junction temperature TJmin -40 · max 125 °C4
IN capacitor CINmin 1 uF4
OUT capacitor COUTmin 1 uF4
VSET resistor RVSETmin 18 · max 100 kΩ4
Tolerance for VSET resistor RVSET_TOLmin -1 · max 1 %4
Temperature coefficient for VSET resistor RVSET_TEMPCOmax 200 ppm/℃4
ISET resistor RISETmin 0.375 · max 30 kΩ4
TS thermistor resistor (recommend 103AT-2) RTSNominal valuetyp 10 kΩ4
Junction-to-ambient thermal resistance (EVM(2)) RθJABQ25170, DSG, 8 PINS; 1oz Copper, 2-layer boardtyp 37 °C/W5
Junction-to-ambient thermal resistance (JEDEC(1)) RθJABQ25170, DSG, 8 PINStyp 75.2 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)BQ25170, DSG, 8 PINStyp 93.4 °C/W5
Junction-to-board thermal resistance RθJBBQ25170, DSG, 8 PINStyp 41.8 °C/W5
Junction-to-top characterization parameter ΨJTBQ25170, DSG, 8 PINStyp 3.8 °C/W5
Junction-to-board characterization parameter ΨJBBQ25170, DSG, 8 PINStyp 41.7 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)BQ25170, DSG, 8 PINStyp 17 °C/W5
Quiescent output current (OUT) IQ_OUTOUT= 4.2V, IN floating or IN = 0V - 5V, Charge Disabled, TJ = 25 °Ctyp 0.35 · max 0.6 uA6
Quiescent output current (OUT) IQ_OUTOUT= 4.2V, IN floating or IN = 0V - 5V, Charge Disabled, TJ < 105 °Ctyp 0.35 · max 0.8 uA6
Shutdown input current (IN) with charge disabled via TS pin ISD_IN_TSIN = 5V, Charge Disabled (VTS < VTS_ENZ), no batterytyp 80 · max 110 uA6
Standby input current (IN) with charge terminated ISTANDBY_ININ = 5V, Charge Enabled, charge terminatedtyp 190 uA6
Quiescent input current (IN) IQ_ININ = 5V, OUT = 3.8V, Charge Enabled, ICHG = 0Atyp 0.45 · max 0.6 mA6
IN operating range VIN_OPmin 3 · max 6.6 V6
IN voltage to start charging VIN_LOWVIN risingmin 3.05 · typ 3.09 · max 3.15 V6
IN voltage to stop charging VIN_LOWVIN fallingmin 2.8 · typ 2.95 · max 3.1 V6
Exit sleep mode threshold VSLEEPZIN rising, VIN - VOUT, OUT = 4Vmin 95 · typ 135 · max 175 mV6
Sleep mode threshold hysteresis VSLEEPIN falling, VIN - VOUT, OUT = 4Vtyp 80 mV6
VIN overvoltage rising threshold VIN_OVIN risingmin 6.6 · typ 6.75 · max 6.9 V6
VIN overvoltage falling threshold VIN_OVZIN fallingtyp 6.63 V6
Highest resistor value considered short RISET_SHORTRISET below this at startup, charger does not initiate charge, power cycle or TS toggle to resetmax 350 Ω6
Highest resistor value considered short RVSET_SHORTRVSET below this at startup, charger does not initiate charge, power cycle or TS toggle to resetmax 2.8 kΩ6
Lowest resistor value considered open RVSET_OPENRVSET above this at startup, charger does not initiate charge, power cycle or TS toggle to resetmin 120 kΩ6
Dropout voltage (VIN - VOUT) VDOVIN falling, VOUT = 4.35V, IOUT = 500mAtyp 425 mV6
OUT charge voltage regulation accuracy VREG_ACCTj = 25℃, all VSET settingsmin -0.5 · max 0.5 %6
OUT charge voltage regulation accuracy VREG_ACCTj = -40℃ to 125℃, all VSET settingsmin -0.8 · max 0.8 %6
Typical charge current regulation range ICHG_RANGEVOUT > VBAT_LOWVmin 10 · max 800 mA6
Charge current setting factor, ICHG = KISET / RISET KISET10mA < ICHG < 800mAmin 270 · typ 300 · max 330 AΩ6
Charge current accuracy ICHG_ACCRISET = 375Ω, OUT = 3.8Vmin 720 · typ 800 · max 880 mA6
Charge current accuracy ICHG_ACCRISET = 600Ω, OUT = 3.8Vmin 450 · typ 500 · max 550 mA6
Charge current accuracy ICHG_ACCRISET = 3.0kΩ, OUT = 3.8Vmin 90 · typ 100 · max 110 mA6
Charge current accuracy ICHG_ACCRISET = 30kΩ, OUT = 3.8Vmin 9 · typ 10 · max 11 mA6
Typical pre-charge current, as percentage of ICHG IPRECHGVOUT < VBAT_LOWVtyp 20 %6
Precharge current accuracy IPRECHG_ACCRISET = 375Ω, OUT = 2.5Vmin 144 · typ 160 · max 176 mA6
Precharge current accuracy IPRECHG_ACCRISET = 600Ω, OUT = 2.5Vmin 85 · typ 100 · max 110 mA6
Precharge current accuracy IPRECHG_ACCRISET = 3.0kΩ, OUT = 2.5Vmin 18 · typ 20 · max 22 mA6
Precharge current accuracy IPRECHG_ACCRISET = 30kΩ, OUT = 2.5Vmin 1.4 · typ 2 · max 2.6 mA6
Typical termination current, as percentage of ICHG ITERMVOUT = VREGtyp 10 %7
Termination current accuracy ITERM_ACCRISET = 600Ω, OUT = VREG = 4.2Vmin 45 · typ 50 · max 55 mA7
Termination current accuracy ITERM_ACCRISET = 3.0kΩ, OUT = VREG = 4.2Vmin 8.5 · typ 10 · max 11.5 mA7
Termination current accuracy ITERM_ACCRISET =30kΩ, OUT = VREG = 4.2Vmin 0.4 · typ 1 · max 1.6 mA7
Output (OUT) short circuit voltage rising threshold, for Li-Ion chemistry VBAT_SHORTOUT rising, VSET configured for Li-Ionmin 2.1 · typ 2.2 · max 2.3 V7
Output (OUT) short circuit voltage rising threshold, for LiFePO4 chemistry VBAT_SHORTOUT rising, VSET configured for LiFePO4min 1.1 · typ 1.2 · max 1.3 V7
Output (OUT) short circuit voltage hysteresis VBAT_SHORT_HYSOUT fallingtyp 200 mV7
OUT short circuit charging current IBAT_SHORTVOUT < VBAT_SHORTmin 12 · typ 16 · max 20 mA7
Pre-charge to fast-charge transition threshold, for Li-Ion chemistry VBAT_LOWVOUT rising, VSET configured for Li-Ionmin 2.7 · typ 2.8 · max 3 V7
Pre-charge to fast-charge transition threshold for Li-FePO4 chemistry VBAT_LOWVOUT rising, VSET configured for LiFePO4min 1.9 · typ 2 · max 2.1 V7
Battery LOWV hysteresis VBAT_LOWV_HYSOUT fallingtyp 100 mV7
Battery recharge threshold for Li-Ion chemistry VRECHGOUT falling, VSET configured for Li-IonVREG_ACC - VOUTmin 75 · typ 100 · max 125 mV7
Battery recharge threshold for LiFePO4 chemistry VRECHGOUT falling, VSET configured for LiFePO4 , VREG_ACC - VOUTmin 175 · typ 200 · max 225 mV7
Charging path FET on-resistance RONIOUT = 400mA, TJ = 25°Ctyp 845 · max 1000 mΩ7
Charging path FET on-resistance RONIOUT = 400mA, TJ = -40 - 125°Ctyp 845 · max 1450 mΩ7
OUT overvoltage rising threshold VOUT_OVPVOUT rising, as percentage of VSETmin 103 · typ 104 · max 105 %7
OUT overvoltage falling threshold VOUT_OVPVOUT falling, as percentage of VSETmin 101 · typ 102 · max 103 %7
Output current limit threshold IOUT_OCPIOUT risingmin 0.9 · typ 1 · max 1.1 A7
Typical junction temperature regulation TREGtyp 125 °C7
Thermal shutdown rising threshold TSHUTTemperature increasingtyp 150 °C7
Thermal shutdown falling threshold TSHUTTemperature decreasingtyp 135 °C7
TS nominal bias current ITS_BIASmin 36.5 · typ 38 · max 39.5 uA7
Cold temperature threshold VCOLDTS pin voltage rising (approx. 0°C)min 0.99 · typ 1.04 · max 1.09 V7
Cold temperature exit threshold VCOLDTS pin voltage falling (approx. 4°C)min 0.83 · typ 0.88 · max 0.93 V7
Hot temperature threshold VHOTTS pin voltage falling (approx. 45°C)min 176 · typ 188 · max 200 mV7
Hot temperature exit threshold VHOTTS pin voltage rising (approx. 40°C)min 208 · typ 220 · max 232 mV7
Charge Disable threshold. Crossing this threshold shall shutdown IC VTS_ENZTS pin voltage fallingmin 40 · typ 50 · max 60 mV7
Charge Enable threshold. Crossing this threshold shall restart IC operation VTS_ENTS pin voltage risingmin 65 · typ 75 · max 85 mV7
TS maximum voltage clamp VTS_CLAMPTS pin open-circuit (float)min 2.3 · typ 2.6 · max 2.9 V7
Output low threshold level VOLSink current = 5mA; STAT, PGmax 0.4 V7
High-level leakage current IOUT_BIASPull up rail 3.3V; STAT, PGmax 1 uA8
TS turn-on time during TS duty cycle mode tTS_DUTY_ONNominal valuetyp 100 ms8
TS turn-off time during TS duty cycle mode tTS_DUTY_OFFNominal valuetyp 2 s8
Deglitch time for IOUT_OCP, IOUT rising tOUT_OCP_DGLNominal valuetyp 100 us8
Pre-charge safety timer accuracy tPRECHGCenter value is nominalmin 28.5 · typ 30 · max 31.5 min8
Fast-charge safety timer accuracy tSAFETYCenter value is nominalmin 9.5 · typ 10 · max 10.5 hr8

Pins, by the datasheet

9
1 IN
External DC input supply; bypass to GND with at least 1-uF capacitor placed close to the IC. · p. 3
2 ISET
Programs fast-charge current with a resistor to GND: 30 kΩ for 10 mA to 375 Ω for 800 mA; precharge and termination currents are 20% and 10% of fast-charge current. · p. 3
3 TS
Battery temperature qualification input; connect NTC thermistor to GND, or 10-kΩ resistor if temperature monitoring is unused; pulling below VTS_ENZ disables charging. · p. 3
4 GND
Ground pin. · p. 3
5 STAT
Charger status output with 10-kΩ pull-up: LOW during charging, HIGH when complete or disabled, blinking at 1 Hz for a fault. · p. 3
6 PG
Power-good output with 10-kΩ pull-up; pulls low when VIN > VIN_LOWV and VOUT + VSLEEPZ < VIN < VIN_OV. · p. 3
7 VSET
Programs OUT regulation voltage with an 18 kΩ to 100 kΩ pull-down resistor; values outside this range suspend charging; use ±1% tolerance and <200 ppm/ºC temperature coefficient. · p. 3
8 OUT
Battery connection with optional parallel system load; bypass to GND with at least 1-uF capacitor placed close to the IC. · p. 3
— Thermal Pad
Exposed heat-dissipation pad; solder to the board with vias connecting to a solid GND plane. · p. 3

Ordering codes, by the datasheet

4
BQ25170DSGR
WSON (DSG), 8 pins · 3000 units, LARGE T&R; operating temperature -40 to 125 °C · p. 28
BQ25170DSGR.A
WSON (DSG), 8 pins · 3000 units, LARGE T&R; operating temperature -40 to 125 °C · p. 28
BQ25170DSGRG4
WSON (DSG), 8 pins · 3000 units, LARGE T&R; operating temperature -40 to 125 °C · p. 28
BQ25170DSGRG4.A
WSON (DSG), 8 pins · 3000 units, LARGE T&R; operating temperature -40 to 125 °C · p. 28

Open-source boards using it

3
  • 2 layers28 × 95 mmCamera clicker, the printed circuit board in 3D

    Camera clicker

    tenderlove/camera-clicker

    WiFi client and remote shutter for Olympus OM-D cameras

    30 parts7Apache-2.0
  • 4 layers90 × 25 mmEsp home sensor, the printed circuit board in 3D

    Esp home sensor

    kamilix2003/esp-home-sensor

    ESP32 based battery powered home sensor

    98 partsMIT
  • 2 layers25 × 25 mmBattery charger, the printed circuit board in 3D

    Battery charger

    kamilix2003/esp-home-sensor

    ESP32 based battery powered home sensor

    29 partsMIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the BQ25170DSG?

Yes. The symbol is EasyEDA_Cloud:BQ25170JDSGR and the footprint EasyEDA_Cloud:WSON-8_L2.0-W2.0-P0.50-TL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the BQ25170DSG?

WSON-8(2x2), with 9 pins. Its footprint is drawn on this page.

Where is the BQ25170DSG datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the BQ25170DSG?

JLCPCB lists it as part C5208201, with 1,046 in stock; the sellers' links on this page open their listings.

What can replace the BQ25170DSG?

Parts like it in the library: the BQ24315DSG by Texas Instruments, the BQ25172DSG by Texas Instruments, the BQ25176MDSG by Texas Instruments and the BQ294700DSGR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the BQ25170DSG?

3 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.