Skip to the content

ASM330LHHXTR

STMicroelectronicsExtended

-40℃~+105℃ 1.71V~3.6V 13uA 3KB IMU (accelerometer + gyroscope) Motion event detection SPI、I2C X,Y,Z X,Y,Z ±16g ±4000dps VFLGA-14L(2.5x3) Accelerometers ROHS

Part id
st/ASM330LHHXTR
Category
Accelerometers
Package
VFLGA-14L(2.5x3)
Pins
14
In stock
1 at JLCPCB (C5267398)
Used on
11 open-source boards

Overview

The ASM330LHHXTR is an accelerometer made by STMicroelectronics in a VFLGA-14L(2.5x3) package with 14 pins. -40℃~+105℃ 1.71V~3.6V 13uA 3KB IMU (accelerometer + gyroscope) Motion event detection SPI、I2C X,Y,Z X,Y,Z ±16g ±4000dps VFLGA-14L(2.5x3) Accelerometers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:ASM330LHHXTR, from EasyEDA) and its footprint (EasyEDA_Cloud:LGA-14_L3.0-W2.5-P0.50-TL, from EasyEDA), ready for a KiCad board. 1 are in stock at JLCPCB (part C5267398). 11 open-source boards in 5 repositories on GitHub use it.

Symbol

1SDO/SA02MSDA3MSCL4INT15Vdd_IO6NC7GND8Vdd9INT210NC11NC12CS13SCL14SDA
EasyEDA_Cloud:ASM330LHHXTRFrom EasyEDA

Footprint

EasyEDA_Cloud:LGA-14_L3.0-W2.5-P0.50-TLFrom EasyEDA

From the datasheet

9
Supply, least
1.71 V · Vdd, recommended operating min · p. 13
Supply, most
3.6 V · Vdd, recommended operating max · p. 13
Supply, least
1.62 V · Vdd_IO, recommended operating min · p. 13
Supply, absolute maximum
4.8 V · Vdd, absolute max · p. 18
Works from
-40 °C · Operating temperature min · p. 13
Works up to
105 °C · Operating temperature max · p. 13
Takes working
1.3 mA · Gyroscope and accelerometer, ODR = 1.6 kHz, typical · p. 13
Takes at most
1.6 mA · Gyroscope and accelerometer, ODR = 1.6 kHz, max · p. 13
Takes asleep
5 µA · Gyroscope and accelerometer power-down, 25 °C, typical · p. 13

What it is and has

11
Qualification
AEC-Q100 qualified · p. 1
Accelerometer full scale
User-selectable up to ±16 g · p. 1
Gyroscope range
±125 to ±4000 dps · p. 1
Operating modes
High-performance and low-power · p. 1
Serial interfaces
I²C, MIPI I3C, SPI · p. 1
Finite state machine
Programmable · p. 1
Machine learning core
Embedded · p. 1
Interrupts
Smart programmable interrupts · p. 1
FIFO
3 KB · p. 1
Compliance
ECOPACK and RoHS compliant · p. 1
Sensor hub
Two internal and up to four external sensors · p. 4

Around it

2
cap 100 nF
between Vdd_IO and GND; Recommended filter capacitor. · p. 9
cap 10 μF
between Vdd and GND; Recommended supply capacitor, together with 100 nF. · p. 9

Specifications

23
ParameterConditionsAs printedPage
Supply voltage VddVdd = 3.0 V, T = -40 °C to +105 °C, up to gyroscope FS = ±2000 dps unless otherwise notedmin 1.71 · max 3.6 V13
Power supply for I/O Vdd_IOmin 1.62 · max 3.6 V13
Gyroscope and accelerometer current consumption GA_IddODR = 1.6 kHztyp 1.3 · max 1.6 mA13
Accelerometer current consumption in high-performance mode A_IddHPODR = 1.6 kHztyp 360 · max 530 uA13
Accelerometer current consumption in low-power mode LA_IddLMODR = 52 Hz, @25 °Ctyp 50 · max 150 uA13
Accelerometer current consumption in low-power mode LA_IddLMODR = 12.5 Hz, @25 °C; evaluated by characterization, not tested in productiontyp 14 uA13
Accelerometer current consumption in low-power mode LA_IddLMODR = 1.6 Hz, @25 °C; evaluated by characterization, not tested in productiontyp 7 uA13
Accelerometer current consumption in low-power mode LA_IddLMVdd = 1.71 V, ODR = 52 Hz, @25 °Ctyp 40 · max 150 uA13
Accelerometer current consumption in low-power mode LA_IddLMVdd = 1.71 V, ODR = 12.5 Hz, @25 °C; evaluated by characterization, not tested in productiontyp 11 uA13
Accelerometer current consumption in low-power mode LA_IddLMVdd = 1.71 V, ODR = 1.6 Hz, @25 °C; evaluated by characterization, not tested in productiontyp 5.5 uA13
Current consumption in low-power mode, combo mode LC_IddLMODR = 52 Hztyp 530 · max 800 uA13
Current consumption in low-power mode, combo mode LC_IddLMODR = 12.5 Hz, @25 °C; evaluated by characterization, not tested in productiontyp 475 uA13
Current consumption in low-power mode, combo mode LC_IddLMVdd = 1.71 V, ODR = 52 Hztyp 520 · max 800 uA13
Current consumption in low-power mode, combo mode LC_IddLMVdd = 1.71 V, ODR = 12.5 Hz, @25 °C; evaluated by characterization, not tested in productiontyp 470 uA13
Gyroscope and accelerometer current consumption during power-down IddPD@25 °Ctyp 5 · max 13 uA13
Turn-on time TonTime to obtain stable sensitivity within ±5% of final value switching from power-down to normal operationtyp 35 ms13
Low-level output voltage VOLIOL = 4 mA; evaluated by characterization, not tested in productionmax 0.2 V13
Operating temperature range Topmin -40 · max 105 °C13
Supply voltage Vddmin -0.3 · max 4.8 V18
Storage temperature range TSTGmin -40 · max 125 °C18
Acceleration g for 0.3 ms Sgmax 3000 g18
Electrostatic discharge protection (HBM) ESDmax 2 kV18
Input voltage on any control pin (including CS, SCL/SPC, SDA/SDI/SDO, SDO/SA0) VinMaximum = Vdd_IO +0.3 Vmin -0.3 V18

Pins, by the datasheet

14
1 SDO/SA0
SPI 4-wire serial data output; least significant bit of the I²C device address and MIPI I3C static address. · p. 9
2 MSDA
Mode 1: connect to Vdd_IO or GND. Mode 2: I²C serial data master. · p. 9
3 MSCL
Mode 1: connect to Vdd_IO or GND. Mode 2: I²C serial clock master. · p. 9
4 INT1
Programmable interrupt 1; set to 1 when used as a MIPI I3C pure slave. · p. 39
5 Vdd_IO
Power supply for I/O pins. · p. 9
6 NC
Connect to Vdd_IO or GND or leave unconnected. · p. 9
7 GND
0 V supply. · p. 9
8 Vdd
Power supply. · p. 9
9 INT2
Programmable interrupt 2 or data enable; mode 2 also supports I²C master external synchronization signal MDRDY. · p. 9
10 NC
Leave electrically unconnected and soldered to PCB. · p. 9
11 NC
Leave electrically unconnected and soldered to PCB. · p. 9
12 CS
Interface selection: high enables I²C/MIPI I3C and leaves SPI idle; low enables SPI and disables I²C/MIPI I3C. · p. 9
13 SCL
I²C/MIPI I3C serial clock or SPI serial port clock SPC. · p. 9
14 SDA
I²C/MIPI I3C serial data, SPI serial data input SDI, or 3-wire serial data output SDO. · p. 9

Ordering codes, by the datasheet

1
ASM330LHHXTR
LGA-14L · Tape and reel; -40 to +105 °C; 2.5 x 3.0 x 0.83 mm3. · p. 1

Open-source boards using it

11See all 11
  • 4 layers55 × 45 mmSensor Board, the printed circuit board in 3D

    Sensor Board

    antholuo/vehicle-daq

    Vehicle data-acquisition system: ESP32-C6 sensor nodes stream IMU and GPS over ESP-NOW to a bridge; the bridge forwards data over USB to a Raspberry Pi, which logs CSV, runs optional AHRS, and supports track capture…

    50 parts1
  • 2 layers50 × 35 mmController module, the printed circuit board in 3D

    Controller module

    InputBlackBoxOutput/INGAME

    Virtual reality controller for playing FPS games

    73 partsMIT
  • 4 layers75 × 75 mmOnboarding, the printed circuit board in 3D

    Onboarding

    Pandas020/Onboarding

    56 parts
  • 4 layers66.7 × 37.6 mmL0destar, the printed circuit board in 3D

    L0destar

    m4rkw/l0destar

    l0destar open-source tracker project

    88 parts43
  • 4 layers66.7 × 37.6 mmL0destar, the printed circuit board in 3D

    L0destar

    m4rkw/l0destar

    l0destar open-source tracker project

    112 parts43
  • 4 layers65.4 × 34.4 mmL0destar, the printed circuit board in 3D

    L0destar

    m4rkw/l0destar

    l0destar open-source tracker project

    73 parts43
  • 4 layers66.7 × 37.6 mmL0destar, the printed circuit board in 3D

    L0destar

    m4rkw/l0destar

    l0destar open-source tracker project

    110 parts43
  • 4 layers66.7 × 37.6 mmL0destar, the printed circuit board in 3D

    L0destar

    m4rkw/l0destar

    l0destar open-source tracker project

    139 parts43

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ASM330LHHXTR?

Yes. The symbol is EasyEDA_Cloud:ASM330LHHXTR and the footprint EasyEDA_Cloud:LGA-14_L3.0-W2.5-P0.50-TL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ASM330LHHXTR?

VFLGA-14L(2.5x3), with 14 pins. Its footprint is drawn on this page.

Where is the ASM330LHHXTR datasheet?

STMicroelectronics publishes it: the Datasheet link on this page opens it.

Where can I order the ASM330LHHXTR?

JLCPCB lists it as part C5267398, with 1 in stock; the sellers' links on this page open their listings.

What can replace the ASM330LHHXTR?

Parts like it in the library: the LSM6DSK320X by STMicroelectronics, the ICM-42688P-HXY by HXY MOSFET, the ICM-42688-P by TDK InvenSense and the LSM6DSVE by STMicroelectronics. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ASM330LHHXTR?

11 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.