Skip to the content
29292929292929292929

CP2102-GMR

Silicon LabsJLCPCB preferred

-40℃~+85℃ 1Mbps 20mA 3V~3.6V 80uA Transceiver USB 2.0 WQFN-28-EP(5x5) USB Converters ROHS

Part id
silabs/CP2102-GMR
Category
USB Converters
Package
WQFN-28-EP(5x5)
Pins
29
In stock
51,411 at JLCPCB (C6568)
Used on
48 open-source boards

Overview

The CP2102-GMR is a USB Converter made by Silicon Labs in a WQFN-28-EP(5x5) package with 29 pins. -40℃~+85℃ 1Mbps 20mA 3V~3.6V 80uA Transceiver USB 2.0 WQFN-28-EP(5x5) USB Converters ROHS.

PCBKit's library has its KiCad symbol (dk_Interface-Controllers:CP2102-GMR_NRND, from Digikey) and its footprint (JLCPCB:WQFN-28_L5.0-W5.0-P0.50-BL-EP3.2, from Cdfer), ready for a KiCad board. 51,411 are in stock at JLCPCB (part C6568). 48 open-source boards in 43 repositories on GitHub use it.

Symbol

1DCD2RI3GND4D+5D-6VDD7REGIN8VBUS9RST10NC11SUSPEND12SUSPEND13NC14NC15NC16NC17NC18VPP18NC19NC20NC21NC22NC23CTS24RTS25RXD26TXD27DSR28DTR29GND_PAD
dk_Interface-Controllers:CP2102-GMR_NRNDFrom Digikey

Footprint

29292929292929292929
JLCPCB:WQFN-28_L5.0-W5.0-P0.50-BL-EP3.2From Cdfer

From the datasheet

11
Supply, least
3 V · VDD, recommended operating min · p. 6
Supply, most
3.6 V · VDD, recommended operating max · p. 6
Supply, least
4 V · REGIN, regulator enabled min · p. 8
Supply, most
5.25 V · REGIN, regulator enabled max · p. 8
Supply, absolute maximum
4.2 V · VDD, absolute max · p. 5
Works from
-40 °C · Ambient operating min · p. 6
Works up to
85 °C · Ambient operating max · p. 6
A pin gives at most
100 mA · RST or any I/O pin sinking, absolute max · p. 5
Junction to air (QFN-28)
32 K/W · typical, multilayer PCB with exposed pad soldered · p. 6
Data rate, most
921.6 kbit/s · UART baud rate max · p. 7
Data rate, most
12 Mbit/s · USB full-speed max · p. 1

What it is and has

7
Clock
Integrated; no external crystal required · p. 1
EEPROM
1024 bytes for USB configuration · p. 21
USB
USB 2.0 compliant, full-speed 12 Mbps · p. 1
UART buffers
576 byte receive; 640 byte transmit · p. 1
Package
RoHS-compliant 28-pin QFN, 5x5 mm · p. 1
Power-on reset
On-chip · p. 1
Voltage regulator
On-chip, 3.3 V output · p. 1

Around it

7
cap 1.0 µF
between REGIN and GND; REGIN decoupling; use with 0.1 uF in parallel. · p. 18
cap 0.1 µF
between REGIN and GND; Additional REGIN decoupling in parallel with 1.0 uF. · p. 18
cap 4.7 F
between VDD and GND; VDD decoupling shown in Figure 6; Figure 5 describes adding this capacitor when powering other devices from the on-chip regulator. · p. 18
cap 0.1 F
between VDD and GND; VDD decoupling shown in Figure 6. · p. 18
res 4.7 k
between RST and VDD; Optional pull-up to increase noise immunity. · p. 14
res 10 k
between SUSPEND and GND; Optional pull-down on the suspend output driven low during suspend; holds it low during initial power-on or reset. · p. 14
diode Littlefuse p/n SP0503BAHT or equivalent
between USB signals and GND; Avalanche transient voltage suppression array for ESD protection, as shown in Figure 5. · p. 14

Specifications

57
ParameterConditionsAs printedPage
Ambient Temperature under Bias TBIASmin -55 · max 125 °C5
Storage Temperature TSTGmin -65 · max 150 °C5
Voltage on VDD with respect to GND VDDmin -0.3 · max 4.2 V5
Maximum Total Current through VDD and GNDmax 500 mA5
Maximum Output Current sunk by RST or any I/O pinmax 100 mA5
Voltage on any I/O Pin, VBUS, or RST with respect to GNDCP2102min -0.3 · max 5.8 V5
Supply Voltage VDD–40 to +85 °Cmin 3 · typ 3.3 · max 3.6 V6
Supply Current - USB Pull-up IPUVDD = 3.0 to 3.6 V, –40 to +85 °Ctyp 200 · max 230 uA6
Specified Operating Temperature Range TAmin -40 · max 85 °C6
Thermal Resistance θJAQFN-28; multi-layer PCB with exposed pad soldered to a PCB padtyp 32 °C/W6
Supply Current—Normal IREGINCP2102; Normal Operation; VREG Enabled; VDD = 3.0 to 3.6 V, –40 to +85 °C; add USB pull-up current for totaltyp 20 · max 26 mA6
Supply Current—Suspended IREGINCP2102; Bus Powered; VREG Enabled; VDD = 3.0 to 3.6 V, –40 to +85 °C; add USB pull-up current for totaltyp 80 · max 100 uA6
Baud RateVDD = 3.0 to 3.6 V, –40 to +85 °Cmax 921600 bps7
Input Leakage Current ILVDD = 3.0 to 3.6 V, –40 to +85 °Ctyp 25 · max 50 uA7
Output Low Voltage VOLCP2102; IOL = 10 uA; VDD = 3.0 to 3.6 V, –40 to +85 °Cmax 0.1 V7
Output Low Voltage VOLCP2102; IOL = 8.5 mA; VDD = 3.0 to 3.6 V, –40 to +85 °Cmax 0.6 V7
Output Low Voltage VOLCP2102; IOL = 25 mA; VDD = 3.0 to 3.6 V, –40 to +85 °Ctyp 1 V7
Input High Voltage VIHCP2102; VDD = 3.0 to 3.6 V, –40 to +85 °Cmin 2 V7
Input Low Voltage VILCP2102; VDD = 3.0 to 3.6 V, –40 to +85 °Cmax 0.8 V7
VDD Ramp Time tRMPTime to VDD ≥ 2.7 V; –40 to +85 °Cmax 1 ms7
RST Low Time to Generate a System Reset tRSTL–40 to +85 °Cmin 15 us7
Input Voltage Range VREGINCP2102; –40 to +85 °Cmin 4 · max 5.25 V8
Output Voltage VDDOUTCP2102; Output Current = 1 to 100 mA; –40 to +85 °Cmin 3 · typ 3.3 · max 3.6 V8
VBUS Detection Input Threshold VVBUSTHCP2102; –40 to +85 °Cmin 1 · typ 1.8 · max 2.9 V8
Bias CurrentCP2102; –40 to +85 °Ctyp 90 uA8
Output High Voltage VOHTransmitter; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 2.8 V8
Output Low Voltage VOLTransmitter; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmax 0.8 V8
Output Crossover Point VCRSTransmitter; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 1.3 · max 2 V8
Output Impedance (CP2102) ZDRVDriving High; VDD = 3.0 V to 3.6 V, –40 to +85 °Ctyp 38 8
Output Impedance (CP2102) ZDRVDriving Low; VDD = 3.0 V to 3.6 V, –40 to +85 °Ctyp 38 8
Pull-up Resistance RPUFull Speed (D+ Pull-up); VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 1.425 · typ 1.5 · max 1.575 k8
Pull-up Resistance RPULow Speed (D- Pull-up); VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 1.425 · typ 1.5 · max 1.575 k8
Output Rise Time TRLow Speed; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 75 · max 300 ns8
Output Rise Time TRFull Speed; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 4 · max 20 ns8
Output Fall Time TFLow Speed; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 75 · max 300 ns8
Output Fall Time TFFull Speed; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 4 · max 20 ns8
Differential Input Sensitivity VDIReceiver; | (D+) - (D-) |; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 0.2 V8
Differential Input Common Mode Range VCMReceiver; VDD = 3.0 V to 3.6 V, –40 to +85 °Cmin 0.8 · max 2.5 V8
Voltage on any I/O Pin, VBUS, or RST with respect to GND, MaximumCP2102; VDD > 3.0 Vmax 5.8 V21
Voltage on any I/O Pin, VBUS, or RST with respect to GND, MaximumCP2102; VDD not poweredmax 5.8 V21
Supply Current—Normal, Typical IREGINCP2102; Normal Operation; VREG Enabledtyp 20 mA21
Supply Current—Normal, Maximum IREGINCP2102; Normal Operation; VREG Enabledmax 26 mA21
Supply Current—Suspended, Typical IREGINCP2102; Bus Powered; VREG Enabledtyp 80 uA21
Supply Current—Suspended, Maximum IREGINCP2102; Bus Powered; VREG Enabledmax 100 uA21
Output Low Voltage, Maximum VOLCP2102; IOL = 8.5 mAmax 0.6 V21
Output Low Voltage, Typical VOLCP2102; IOL = 25 mAtyp 1 V21
Input High Voltage, Minimum VIHCP2102min 2 V21
Input Low Voltage, Maximum VILCP2102max 0.8 V21
Regulator Input Voltage Range, Minimum VREGINCP2102min 4 V22
Regulator Output Voltage, Minimum VDDOUTCP2102; Output Current = 1 to 100 mAmin 3 V22
Regulator Output Voltage, Typical VDDOUTCP2102; Output Current = 1 to 100 mAtyp 3.3 V22
VBUS Detection Input Threshold, Minimum VVBUSTHCP2102min 1 V22
VBUS Detection Input Threshold, Typical VVBUSTHCP2102typ 1.8 V22
VBUS Detection Input Threshold, Maximum VVBUSTHCP2102max 2.9 V22
Regulator Bias Current, TypicalCP2102typ 90 uA22
USB Transceiver Output Impedance, Typical ZDRVCP2102; Driving Hightyp 38 Ω22
USB Transceiver Output Impedance, Typical ZDRVCP2102; Driving Lowtyp 38 Ω22

Pins, by the datasheet

28
1 DCD
Data Carrier Detect control input, active low; may be left unconnected when unused. · p. 10
2 RI
Ring Indicator control input, active low; may be left unconnected when unused. · p. 10
3 GND
Ground. · p. 10
4 D+
USB D+. · p. 10
5 D–
USB D–. · p. 10
6 VDD
3.0–3.6 V supply input, or 3.3 V regulator output when the regulator is enabled. · p. 10
7 REGIN
5 V input to the on-chip voltage regulator. · p. 10
8 VBUS
Connect to USB VBUS; a 5 V signal indicates a USB network connection. · p. 10
9 RST
Device reset; open-drain output of internal POR or VDD monitor; drive low for at least 15 us to initiate reset. · p. 10
10 NC
Leave unconnected or tie to VDD. · p. 10
11 SUSPEND
Driven low in USB suspend; may be left unconnected when unused. · p. 10
12 SUSPEND
Driven high in USB suspend; may be left unconnected when unused. · p. 10
13 NC
Leave unconnected or tie to VDD. · p. 10
14 NC
Leave unconnected or tie to VDD. · p. 10
15 NC
Leave unconnected or tie to VDD. · p. 10
16 NC
Leave unconnected or tie to VDD. · p. 10
17 NC
Leave unconnected or tie to VDD. · p. 10
18 NC
Unused on CP2102; leave unconnected or tie to VDD; may connect to the VPP programming capacitor for CP2109 board compatibility. · p. 10
19 NC
Leave unconnected or tie to VDD. · p. 10
20 NC
Leave unconnected or tie to VDD. · p. 10
21 NC
Leave unconnected or tie to VDD. · p. 10
22 NC
Leave unconnected or tie to VDD. · p. 10
23 CTS
Clear To Send control input, active low; may be left unconnected when unused. · p. 10
24 RTS
Ready to Send control output, active low; may be left unconnected when unused. · p. 10
25 RXD
Asynchronous UART receive data input. · p. 10
26 TXD
Asynchronous UART transmit data output. · p. 10
27 DSR
Data Set Ready control input, active low; may be left unconnected when unused. · p. 10
28 DTR
Data Terminal Ready control output, active low; may be left unconnected when unused. · p. 10

Open-source boards using it

48See all 48
  • 2 layers189.5 × 204.9 mmSmartSpin2k Panelized, the printed circuit board in 3D

    SmartSpin2k Panelized

    doudar/SmartSpin2k

    Transform your spin bike into a Smart Trainer!

    749 parts292GPL-2.0
  • 4 layers93.7 × 43.7 mmFlight Computer, the printed circuit board in 3D

    Flight Computer

    SunDevilRocketry/Flight-Computer

    General purpose flight computer for high powered rocketry projects.

    113 parts5
  • 2 layers45 × 20 mmLICHEE JACK USB DEBUGGER, the printed circuit board in 3D

    LICHEE JACK USB DEBUGGER

    KaliAssistant/Lichee-Jack-pcb

    Open hardware extension board for Lichee-Jack with battery, Ethernet, and LED integration.

    56 parts4GPL-3.0
  • 4 layers66.8 × 150 mmCooee Big brains, the printed circuit board in 3D

    Cooee Big brains

    DetectiveMittens/Cooee

    An open-source phone that can operate without GSM or LTE coverage. Utilising LoRa modulation and mesh networking to enable long range "off-grid" communication

    200 parts3GPL-2.0
  • 4 layers64 × 77 mmOBSPro, the printed circuit board in 3D

    OBSPro

    FabianSchwartau/OBSPro

    Version of the OpenBikeSensor hardware optimized for PCBA

    131 parts3LGPL-2.1
  • 2 layers191 × 125.5 mmXcku5p board, the printed circuit board in 3D

    Xcku5p board

    sjbar03/XCKU5P-Development-Notes

    Notes while learning how to develop with the Xilinx Ultrascale+ XCKU5P FPGA. Also notes on PCB design.

    96 parts3
  • 2 layers290 × 100 mmESP32-Wall Clock, the printed circuit board in 3D

    ESP32-Wall Clock

    SkullKill/ESP32-Wall-Clock-PCB

    ESP32 based 30cm Wall Mounted Clock. WiFi, NTP, SNMP, web interface, MicroUsb, Type-C, HG3613 Retrofit

    207 parts3GPL-3.0
  • 2 layers47 × 29.2 mmESP32 Dev Kit, the printed circuit board in 3D

    ESP32 Dev Kit

    BrijModi/ESP32-Dev-Kit-Clone

    A 2-layer PCB design of the ESP32 Dev Kit V1 (30-pin), created using KiCad 9.0. Includes complete schematics, layout, and BOM.

    26 parts2

Questions

Is there a KiCad symbol and footprint for the CP2102-GMR?

Yes. The symbol is dk_Interface-Controllers:CP2102-GMR_NRND and the footprint JLCPCB:WQFN-28_L5.0-W5.0-P0.50-BL-EP3.2, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the CP2102-GMR?

WQFN-28-EP(5x5), with 29 pins. Its footprint is drawn on this page.

Where is the CP2102-GMR datasheet?

Silicon Labs publishes it: the Datasheet link on this page opens it.

Where can I order the CP2102-GMR?

JLCPCB lists it as part C6568, with 51,411 in stock; the sellers' links on this page open their listings.

Which open-source boards use the CP2102-GMR?

48 boards in 43 repositories on GitHub; the most starred are listed on this page, with their KiCad files.