SX1508BIULTRT
SEMTECHExtended
-40℃~+85℃ 1.425V~3.6V 15mA 1uA 4 400kHz 8 8mA I2C Interrupt Output Push-Pull、Open-drain Reset function、Cascading and address extension、Input anti-jitter、Keyboard matrix scanning、Built-in LED driver、IO level configurable、PWMOptocouplers QFN-20-EP(3x3) I/O Expanders ROHS
- Part id
- semtech/SX1508BIULTRT
- Category
- I, O Expanders
- Package
- QFN-20-EP(3x3)
- Pins
- 21
- In stock
- 70 at JLCPCB (C2652273)
Overview
The SX1508BIULTRT is an i, O Expander made by SEMTECH in a QFN-20-EP(3x3) package with 21 pins. -40℃~+85℃ 1.425V~3.6V 15mA 1uA 4 400kHz 8 8mA I2C Interrupt Output Push-Pull、Open-drain Reset function、Cascading and address extension、Input anti-jitter、Keyboard matrix scanning、Built-in LED driver、IO level configurable、PWMOptocouplers QFN-20-EP(3x3) I/O Expanders ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:SX1508BIULTRT, from EasyEDA) and its footprint (EasyEDA_Cloud:QFN-20_L3.0-W3.0-P0.40-TL-EP1.7, from EasyEDA), ready for a KiCad board. 70 are in stock at JLCPCB (part C2652273).
Symbol
Footprint
From the datasheet
10- Supply, least
- 1.425 V · VDDM, recommended operating min · p. 7
- Supply, most
- 3.6 V · VDDM, recommended operating max · p. 7
- Supply, least
- 1.2 V · VCC1,2, recommended operating min · p. 7
- Supply, absolute maximum
- 3.7 V · VDDM, absolute max · p. 7
- Works from
- -40 °C · Operating ambient temperature min · p. 7
- Works up to
- 85 °C · Operating ambient temperature max · p. 7
- Junction, hottest
- 125 °C · Junction temperature max · p. 7
- Takes working
- 177 µA · sum of VDDM, VCC1 and VCC2 typical; internal oscillator 2MHz, I²C inactive, no output load · p. 7
- A pin gives at most
- 15 mA · I/O output sink current max, VCC1,2 >= 2V · p. 7
- Data rate, most
- 400 kbit/s · I²C fast mode max · p. 13
What it is and has
13- GPIO channels
- 8 · p. 1
- Package
- QFN-UT-20 · p. 1
- LED intensity control
- 256-step PWM · p. 1
- LED blink control
- 224 On/Off values · p. 1
- LED breathing control
- 224 Fade In/Out values · p. 1
- Input debouncer
- Configurable · p. 1
- I/O pull resistors
- Programmable pull-up/pull-down · p. 1
- I/O output modes
- Push/pull or open-drain · p. 1
- I/O polarity
- Programmable · p. 1
- Interrupt output
- Open drain, active low, NINT · p. 1
- I²C slave addresses
- 4 user-selectable · p. 1
- Reset
- Power-on reset and NRESET input · p. 1
- Compliance
- Pb & Halogen Free, RoHS/WEEE compliant · p. 1
Specifications
74| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Main supply voltage Vmax_VDDM | min -0.4 · max 3.7 V | 7 | |
| Digital I/O pin supply voltage Vmax_VCC1-2 | min -0.4 · max 3.7 V | 7 | |
| Electrostatic handling HBM model (SX1508B) VES_HBM | SX1508B; tested according to JESD22-A114A | max 2000 V | 7 |
| Electrostatic handling CDM model VES_CDM | max 1000 V | 7 | |
| Electrostatic handling MM model (SX1508B) VES_MM | SX1508B | max 200 V | 7 |
| Operating ambient temperature range TA | min -40 · max 85 °C | 7 | |
| Junction temperature range TC | min -40 · max 125 °C | 7 | |
| Storage temperature range TSTG | min -55 · max 150 °C | 7 | |
| Main supply voltage VDDM | min 1.425 · max 3.6 V | 7 | |
| I/O banks supply voltage VCC1,2 | min 1.2 · max 3.6 V | 7 | |
| Main supply current IDDM | SX1508B, I²C inactive; Oscillator OFF | typ 1 · max 5 uA | 7 |
| Main supply current IDDM | SX1508B, I²C inactive; Internal osc. (2MHz) | typ 175 · max 235 uA | 7 |
| Main supply current IDDM | SX1508B, I²C inactive; External osc. (32kHz) | typ 10 uA | 7 |
| I/O banks supply current ICC1,2 | No load connected to outputs and inputs fixed to VCC1,2 or GND | typ 1 · max 2 uA | 7 |
| High level input voltage VIH | I/Os set as Input; VCC1,2 >= 2V; min = 0.7*VCC1,2; 5.5 V max with RegHighInput enabled and VCCx min = 1.65V, else 3.6 V | max 5.5 V | 7 |
| High level input voltage VIH | I/Os set as Input; VCC1,2 < 2V; min = 0.8*VCC1,2; 5.5 V max with RegHighInput enabled and VCCx min = 1.65V, else 3.6 V | max 5.5 V | 7 |
| Low level input voltage VIL | I/Os set as Input; VCC1,2 >= 2V; max = 0.3*VCC1,2 | min -0.4 V | 7 |
| Low level input voltage VIL | I/Os set as Input; VCC1,2 < 2V; max = 0.2*VCC1,2 | min -0.4 V | 7 |
| Input leakage current ILEAK | I/Os set as Input; Assuming no active pull-up/down | min -1 · max 1 uA | 7 |
| Input capacitance CI | I/Os set as Input | max 10 pF | 7 |
| Low level output voltage VOL | I/Os set as Output | min -0.4 · max 0.3 V | 7 |
| High level output source current IOH | I/Os set as Output; VCC1,2 >= 2V | max 8 mA | 7 |
| High level output source current IOH | I/Os set as Output; VCC1,2 < 2V | max 2 mA | 7 |
| Low level output sink current IOL | I/Os set as Output; VCC1,2 >= 2V | max 15 mA | 7 |
| Low level output sink current IOL | I/Os set as Output; VCC1,2 < 2V | max 8 mA | 7 |
| Output data valid timing tPV | Cf. Figure 8 | max 425 ns | 8 |
| Low level output voltage VOL | NINT (Output) | min -0.4 · max 0.3 V | 8 |
| Low level output sink current IOLM | NINT (Output); VDDM >= 2V | max 8 mA | 8 |
| Low level output sink current IOLM | NINT (Output); VDDM < 2V | max 4 mA | 8 |
| Interrupt valid timing tIV | NINT (Output); From input data change | max 4 us | 8 |
| Interrupt reset timing tIR | NINT (Output); From RegInterruptSource clearing | max 4 us | 8 |
| Low level input voltage VILM | NRESET (Input); VDDM >= 2V; max = 0.3*VDDM | min -0.4 V | 8 |
| Low level input voltage VILM | NRESET (Input); VDDM < 2V; max = 0.2*VDDM | min -0.4 V | 8 |
| Input leakage current ILEAK | NRESET (Input) | min -1 · max 1 uA | 8 |
| Input capacitance CI | NRESET (Input) | max 10 pF | 8 |
| Power-On-Reset voltage VPOR | Cf. Figure 6 | typ 0.8 V | 8 |
| Low brown-out voltage VDROPL | Cf. Figure 6 | typ 0.2 V | 8 |
| Reset time tRESET | Cf. Figure 6 | max 2.5 ms | 8 |
| Reset pulse from host uC tPULSE | Cf. Figure 6 | min 200 ns | 8 |
| Low level input voltage VILM | ADDR0, ADDR1 (Inputs); VDDM >= 2V; max = 0.3*VDDM | min -0.4 V | 8 |
| Low level input voltage VILM | ADDR0, ADDR1 (Inputs); VDDM < 2V; max = 0.2*VDDM | min -0.4 V | 8 |
| Input leakage current ILEAK | ADDR0, ADDR1 (Inputs) | min -1 · max 1 uA | 8 |
| Input capacitance CI | ADDR0, ADDR1 (Inputs) | max 10 pF | 8 |
| Low level input voltage VILMO | OSCIO (Input/Output); VDDM >= 2V; max = 0.3*VDDM | min -0.4 V | 8 |
| Low level input voltage VILMO | OSCIO (Input/Output); 1.425V =< VDDM < 2V; max = 0.2*VDDM | min -0.4 V | 8 |
| Low level input voltage VILMO | OSCIO (Input/Output); VDDM < 1.425V; max = 0.1*VDDM | min -0.4 V | 8 |
| Input leakage current ILEAK | OSCIO (Input/Output) | min -1 · max 1 uA | 8 |
| Input capacitance CI | OSCIO (Input/Output) | max 10 pF | 8 |
| Low level output voltage VOL | OSCIO (Input/Output) | min -0.4 · max 0.3 V | 8 |
| High level output source current IOHM | OSCIO (Input/Output); VDDM >= 2V | max 8 mA | 8 |
| High level output source current IOHM | OSCIO (Input/Output); VDDM < 2V | max 2 mA | 8 |
| Low level output sink current IOLM | OSCIO (Input/Output); VDDM >= 2V | max 8 mA | 8 |
| Low level output sink current IOLM | OSCIO (Input/Output); VDDM < 2V | max 4 mA | 8 |
| Low level output voltage VOL | SCL (Input) and SDA (Input/Output) | min -0.4 · max 0.3 V | 8 |
| Low level output sink current IOLM | SCL (Input) and SDA (Input/Output); VDDM >= 2V | max 8 mA | 8 |
| Low level output sink current IOLM | SCL (Input) and SDA (Input/Output); VDDM < 2V | max 4 mA | 8 |
| Low level input voltage VILM | SCL (Input) and SDA (Input/Output); VDDM >= 2V; max = 0.3*VDDM | min -0.4 V | 8 |
| Low level input voltage VILM | SCL (Input) and SDA (Input/Output); VDDM < 2V; max = 0.2*VDDM | min -0.4 V | 8 |
| SCL clock frequency fSCL | max 400 kHz | 9 | |
| Hold time (repeated) START condition tHD;STA | min 0.6 us | 9 | |
| LOW period of the SCL clock tLOW | min 1.3 us | 9 | |
| HIGH period of the SCL clock tHIGH | min 0.6 us | 9 | |
| Set-up time for a repeated START condition tSU;STA | min 0.6 us | 9 | |
| Data hold time tHD;DAT | Maximum applies only if device does not stretch LOW period of SCL | min 0 · max 0.9 us | 9 |
| Data set-up time tSU;DAT | Fast mode; Standard mode requires tSU;DAT ≥ 250 ns | min 100 ns | 9 |
| Rise time of both SDA and SCL tr | min = 20+0.1Cb; Cb is total capacitance of one bus line in pF | max 300 ns | 9 |
| Fall time of both SDA and SCL tf | min = 20+0.1Cb; Cb is total capacitance of one bus line in pF; faster fall-times allowed if mixed with Hs-mode devices | max 300 ns | 9 |
| Set-up time for STOP condition tSU;STO | min 0.6 us | 9 | |
| Bus free time between a STOP and START condition tBUF | min 1.3 us | 9 | |
| Capacitive load for each bus line Cb | max 400 pF | 9 | |
| Pulse width of spikes suppressed by the input filter tSP | max 50 ns | 9 | |
| Programmable pull-up/down resistors for IO[0-7] RPULL | typ 42 kΩ | 9 | |
| Oscillator frequency fOSC | Internal | min 1.3 · typ 2 · max 2.6 MHz | 9 |
| Oscillator frequency fOSC | External from OSCIN (40-60% duty cycle) | max 2.6 MHz | 9 |
Pins, by the datasheet
21- 1 NRESET
- Active low reset input. · p. 4
- 2 SDA
- I2C serial data line. · p. 4
- 3 SCL
- I2C serial clock line. · p. 4
- 4 ADDR0
- Address input bit 0, connect to VDDM or GND. · p. 4
- 5 I/O[0]
- Input at power-on; programmable I/O and LED intensity control (PWM). · p. 4
- 6 I/O[1]
- Input at power-on; programmable I/O and LED intensity control (PWM). · p. 4
- 7 VCC1
- Supply voltage for Bank A I/O[3-0]. · p. 4
- 8 GND
- Ground Pin. · p. 4
- 9 I/O[2]
- Input at power-on; programmable I/O and LED intensity control (PWM), Blinking. · p. 4
- 10 I/O[3]
- Input at power-on; programmable I/O and LED intensity control (PWM), Blinking, Breathing (Fade In/Out). · p. 4
- 11 NINT
- Active low interrupt output. · p. 4
- 12 ADDR1
- Address input bit 1, connect to VDDM or GND. · p. 4
- 13 OSCIO
- Oscillator input/output, can also be used as GPO; programmable through I2C. · p. 4
- 14 VDDM
- Main supply voltage. · p. 4
- 15 I/O[4]
- Input at power-on; programmable I/O and LED intensity control (PWM). · p. 4
- 16 I/O[5]
- Input at power-on; programmable I/O and LED intensity control (PWM). · p. 4
- 17 VCC2
- Supply voltage for Bank B I/O[7-4]. · p. 4
- 18 GND
- Ground Pin. · p. 4
- 19 I/O[6]
- Input at power-on; programmable I/O and LED intensity control (PWM), Blinking. · p. 4
- 20 I/O[7]
- Input at power-on; programmable I/O and LED intensity control (PWM), Blinking, Breathing (Fade In/Out). · p. 4
- PAD GND
- Ground pad shown in package pinout. · p. 4
Ordering codes, by the datasheet
1- SX1508BIULTRT
- QFN-UT-20 · 8 I/Os; marking GAA2 · p. 1
Parts like it
8SX1502I087TRT
QFN-20-EP(3x3)-40℃~+85℃ 1.2V~5.5V 400kHz 8 I2C Interrupt Output QFN-20-EP(3x3) I/O Expanders ROHSSEMTECHI/O ExpandersSX1508QBIULTRT
QFN-20-EP(3x3)-40℃~+85℃ 1.425V~3.6V 400kHz I2C No Interrupt Output QFN-20-EP(3x3) I/O Expanders ROHSSEMTECHI/O ExpandersPCA9555PW
TSSOP-24-40℃~+85℃ 1.1uA 16 2.3V~5.5V 3mA 400kHz 8 I2C、SMBus Interrupt Output Reset function、Cascade and address expansion TSSOP-24 I/O Expanders ROHSNXP SemiconductorsI/O ExpandersAW9523BTQR
TQFN-24-EP(4x4)-40℃~+85℃ 100nA 16 2.4V~5.5V 20mA 4 400kHz 60mV I2C Interrupt Output Push-Pull、Open-drain Reset function、Cascading and address extension、Input anti-jitter、Built-in LED driver、IO level configurable TQFN-24-EP(4x4) I/O Expanders ROHSAWINICI/O ExpandersTCA6416ARTWR
WQFN-24-EP(4x4)-40℃~+85℃ 1.65V~5.5V 10mA 16 2 200mV 25mA 3uA 4.1V 400kHz I2C、SMBus Interrupt Output Push-Pull Reset function、Cascading and address extension、Built-in LED driver、IO level configurable WQFN-24-EP(4x4) I/O Expanders ROHSTexas InstrumentsI/O ExpandersTCA9535PW
TSSOP-24-40℃~+85℃ 1.5uA 1.65V~5.5V 10mA 16 25mA 400kHz 4V 8 I2C、SMBus Interrupt Output Push-Pull Reset function、Cascade and address expansion、Built-in LED driver TSSOP-24 I/O Expanders ROHSTexas InstrumentsI/O ExpandersTCA9555PW
TSSOP-24-40℃~+85℃ 1.65V~5.5V 10mA 16 25mA 3.5uA 400kHz 4V 500mV 8 I2C、SMBus Interrupt Output Push-Pull Reset function、Cascading and address extension、Built-in LED driver TSSOP-24 I/O Expanders ROHSTexas InstrumentsI/O ExpandersTCA6424ARGJR
VQFN-32-EP(5x5)-40℃~+85℃ 1.65V~5.5V 10mA 1uA 2 230mV 24 25mA 4.1V 400kHz I2C、SMBus Interrupt Output Push-Pull Reset function、Cascading and address extension、Built-in LED driver、IO level configurable VQFN-32-EP(5x5) I/O Expanders ROHSTexas InstrumentsI/O Expanders
Questions
Is there a KiCad symbol and footprint for the SX1508BIULTRT?
Yes. The symbol is EasyEDA_Cloud:SX1508BIULTRT and the footprint EasyEDA_Cloud:QFN-20_L3.0-W3.0-P0.40-TL-EP1.7, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the SX1508BIULTRT?
QFN-20-EP(3x3), with 21 pins. Its footprint is drawn on this page.
Where is the SX1508BIULTRT datasheet?
SEMTECH publishes it: the Datasheet link on this page opens it.
Where can I order the SX1508BIULTRT?
JLCPCB lists it as part C2652273, with 70 in stock; the sellers' links on this page open their listings.
What can replace the SX1508BIULTRT?
Parts like it in the library: the SX1502I087TRT by SEMTECH, the SX1508QBIULTRT by SEMTECH, the PCA9555PW by NXP Semiconductors and the AW9523BTQR by AWINIC. Check their datasheets: a part that fits the footprint may still differ in its ratings.