Skip to the content
33

SX1255IWLTRT

SEMTECHExtended

-40℃~+85℃ 18mA 2.7V~3.6V 400MHz~510MHz 434MHz 60mA 7dBm 802.15.4 SPI transceiver QFN-32-EP(5x5) RF Transceiver ICs ROHS

Part id
semtech/SX1255IWLTRT
Category
RF Transceiver ICs
Package
QFN-32-EP(5x5)
Pins
33
In stock
68 at JLCPCB (C89372)
Used on
8 open-source boards

Overview

The SX1255IWLTRT is a RF Transceiver IC made by SEMTECH in a QFN-32-EP(5x5) package with 33 pins. -40℃~+85℃ 18mA 2.7V~3.6V 400MHz~510MHz 434MHz 60mA 7dBm 802.15.4 SPI transceiver QFN-32-EP(5x5) RF Transceiver ICs ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:SX1255IWLTRT, from EasyEDA) and its footprint (EasyEDA_Cloud:QFN-32_L5.0-W5.0-P0.50-BL-EP3.1, from EasyEDA), ready for a KiCad board. 68 are in stock at JLCPCB (part C89372). 8 open-source boards in 6 repositories on GitHub use it.

Symbol

1VR_PA2VBAT13VR_ANA14GND5VR_DIG6XTA7GND8XTB9Reset10CLK_OUT11CLK_IN12Q_IN13I_IN14Q_OUT15I_OUT16VBAT217SCK18MISO19MOSI20NSS21DIO022DIO123DIO224DIO325VR_ANA226GND27RF_IN28GND29RF_ON30RF_OP31GND32VBAT333Ground
EasyEDA_Cloud:SX1255IWLTRTFrom EasyEDA

Footprint

33
EasyEDA_Cloud:QFN-32_L5.0-W5.0-P0.50-BL-EP3.1From EasyEDA

From the datasheet

11
Supply, least
2.7 V · VBAT, recommended operating min · p. 9
Supply, most
3.6 V · VBAT, recommended operating max · p. 9
Supply, absolute maximum
3.9 V · VBAT, absolute maximum supply voltage · p. 9
Works from
-40 °C · Operating temperature min · p. 9
Works up to
85 °C · Operating temperature max · p. 9
Junction, hottest
125 °C · Junction temperature absolute max · p. 9
Takes working
18 mA · Receive mode typical, 3.3 V, 25 °C · p. 10
Takes at most
90 mA · Transmit mode max at -5 dBm output · p. 10
Takes asleep
200 nA · Sleep mode typical · p. 10
Takes asleep
1.15 mA · Standby mode typical, crystal oscillator enabled · p. 10
Junction to air (MLPQW-32)
23.8 K/W · Typical, still air, 4-layer FR4 PCB · p. 41

What it is and has

12
I and Q modulation
Fully flexible modulator and demodulator · p. 1
Duplex operation
Half or full-duplex · p. 1
RX LNA
Bullet proof · p. 1
Filtering
Analog TX and RX pre-filtering · p. 1
I2S
Decimated I&Q signal · p. 1
TX FIR-DAC filter
Programmable tap · p. 1
Materials
Pb-free, Halogen Free · p. 1
Compliance
RoHS / WEEE · p. 1
Package
MLPQ-W 5 x 5 mm, 32 lead · p. 6
ESD
Class 2, JEDEC JESD22-A114-C, Human Body Model, all pins · p. 9
ESD
Class III, JEDEC JESD22-C101-C, Charged Device Model, all pins · p. 9
Transceiver
Low power digital I and Q RF multi-PHY mode · p. 1

Specifications

70
ParameterConditionsAs printedPage
Maximum Supply Voltage VDDmrmin -0.5 · max 3.9 V9
Maximum Temperature Tmrmin -55 · max 115 °C9
Maximum Junction Temperature Tjmax 125 °C9
Maximum RF Input Level Pmrmax 6 dBm9
Operational Supply Voltage VDDopmin 2.7 · max 3.6 V9
Operational Temperature Topmin -40 · max 85 °C9
Load Capacitance on Digital Ports Clopmax 25 pF9
RF Input Level MLmax 0 dBm9
Supply Current in Sleep Mode IDDSLtyp 0.2 · max 1 uA10
Supply Current in Standby Mode IDDSTCrystal oscillator enabledtyp 1.15 · max 1.5 mA10
Supply Current in Receive Mode IDDRXtyp 18 · max 25 mA10
Supply Current in Transmit Mode IDDTXRFOutput Power = -5 dBmtyp 60 · max 90 mA10
Synthesizer Frequency Range FRProgrammablemin 400 · max 510 MHz10
Crystal Oscillator Frequency FXOSCSee Section 5min 32 · typ 36 · max 36.864 MHz10
Crystal Oscillator Wake-up Time TS_OSFrom sleep modetyp 300 · max 500 us10
RX Frequency Synthesizer Wake-up Time TS_FSCrystal Oscillator Enabledtyp 50 · max 150 us10
Frequency Synthesizer Step Size FSTEPFSTEP = FXOSC / 220min 30.5 · typ 34.3 · max 35.16 Hz10
RX Frequency Synthesizer Hop Time (to within 10 kHz of target frequency) TS_HOP_RX200 kHz steptyp 20 us10
RX Frequency Synthesizer Hop Time (to within 10 kHz of target frequency) TS_HOP_RX400 kHz steptyp 20 us10
RX Frequency Synthesizer Hop Time (to within 10 kHz of target frequency) TS_HOP_RX1.2 MHz steptyp 30 us10
RX Frequency Synthesizer Hop Time (to within 10 kHz of target frequency) TS_HOP_RX25 MHz steptyp 50 us10
RX Frequency Synthesizer Hop Time (to within 10 kHz of target frequency) TS_HOP_TX200 kHz steptyp 20 us10
External Clock Frequency for TX Synthesizer or DAC input clock FCLK_INSX1255 slave modemin 32 · max 36.864 MHz11
Transmitter Wake-up Time TS_TRFrequency synthesizer enabledtyp 120 us11
TX Maximum Output Power TXPmaxSaturated Powermin 4 · typ 7 dBm11
TX 1 dB Compression Point TXP1dBPeak Valuemin 2 · typ 5 dBm11
TX Output IP3 TXOIP3-5 dBm average output powermin 13 · typ 16 dBm11
Transmitter Phase Noise PHN10 kHz offset from carriertyp -110 dBc/Hz11
Transmitter Phase Noise PHN100 kHz offset from carriertyp -108 dBc/Hz11
Transmitter Phase Noise PHN1 MHz offset from carriertyp -128 dBc/Hz11
Transmitter Output Noise Floor PHNF10 MHz offset from carriermin -128 · typ -135 dBc/Hz11
Transmitter Integrated DSB Phase Noise PHNIDIntegrated bandwidth from 500 Hz to 125 kHztyp 0.2 · max 1.5 °RMS11
Transmitter IQ Gain Mismatch TXGMtyp 0.5 · max 1 dB11
Transmitter IQ Phase Mismatch TXPMtyp 1 · max 3 °11
Transmitter Analog Prefilter BW (DSB) TXBWANAProgrammable in 31 stepsmin 420 · max 1700 kHz11
Transmitter Analog Prefilter BW precision TXBWANAPrcmin -30 · max 30 %11
Transmitter FIR-DAC Taps TXBWDIFGProgrammablemin 24 · max 64 -11
TX LO Leakage (Before DC offset Calibration) TXLOADC rms input: -10 dBFStyp -8 dBc11
External Clock Frequency for RX ADC FCLK_INSX1255 slave modemin 32 · max 36.864 MHz11
External Clock Jitter Specification CLK_INJExternal clock. White noisemax 0.01 %11
Receiver Noise Figure RXNFMaximum LNA Gaintyp 4.5 · max 7 dB11
Receiver Noise Figure RXNFMaximum LNA Gain -6dBtyp 6.5 · max 9 dB11
Receiver Noise Figure RXNFMinimum LNA Gaintyp 38 · max 40 dB11
RX Gain Range RXGRAdjustable in 2 dB stepstyp 70 dB11
3rd Order Input Intercept Point IIP3Maximum LNA Gain; unwanted tones are 2 MHz and 3.8 MHz above the LOmin -28 · typ -23 dBm11
3rd Order Input Intercept Point IIP3Maximum LNA Gain -6dB; unwanted tones are 2 MHz and 3.8 MHz above the LOmin -21 · typ -16 dBm11
3rd Order Input Intercept Point IIP3Minimum LNA Gain; unwanted tones are 2 MHz and 3.8 MHz above the LOmin 10 · typ 20 dBm11
Receiver IQ Gain Mismatch RXGMtyp 0.5 · max 1 dB12
Receiver IQ Phase Mismatch RXPMtyp 0.5 · max 3 °12
Receiver Analog Prefilter BW (SSB) RXBWANAProgrammablemin 500 · max 1500 kHz12
Digital Input High Level VIHmin 0.8 VDD12
Digital Input Low Level VILmax 0.2 VDD12
Digital Output High Level VOHImax = 1 mAmin 0.9 VDD12
Digital Output Low Level VOLImax = -1 mAmax 0.1 VDD12
SCK Frequency FSCKmax 10 MHz12
SCK High Time tchmin 50 ns12
SCK Low Time tclmin 50 ns12
SCK Rise Time trisetyp 5 ns12
SCK Fall Time tfalltyp 5 ns12
MOSI Set-up Time tsetupFrom MOSI change to SCK rising edgemin 30 ns12
MOSI Hold Time tholdFrom SCK rising edge to MOSI changemin 60 ns12
NSS Set-up Time tnsetupFrom NSS falling edge to SCK rising edgemin 30 ns12
NSS Hold Time tnholdFrom SCK falling edge to NSS rising edgemin 100 ns12
NSS High Time Between SPI Access tnhighmin 20 ns12
Data Hold and Set-up Time tdatamin 250 ns12
Theta jaMLPQW-32; still air, 4-layer FR4 PCB, Jedec standardtyp 23.8 ° C/W41
XTAL Frequency FXOSCmin 32 · max 36.864 MHz37
XTAL Series Resistance RStyp 30 · max 140 Ω37
XTAL Shunt Capacitance C0typ 2.8 · max 7 pF37
External Foot Capacitance CLOADOn each pin XTA and XTBmin 8 · typ 16 · max 22 pF37

Pins, by the datasheet

33
0 Ground
Exposed ground pad. · p. 8
1 VR_PA
Regulated supply for TX amplifier. · p. 8
2 VBAT1
VBAT supply voltage. · p. 8
3 VR_ANA1
Regulated supply for analog TX circuit. · p. 8
4 GND
Ground. · p. 8
5 VR_DIG
Regulated supply for digital circuit. · p. 8
6 XTA
Crystal pad. · p. 8
7 GND
Ground. · p. 8
8 XTB
Crystal pad / input for external clock. · p. 8
9 Reset
Reset. · p. 8
10 CLK_OUT
36 MHz digital clock output. · p. 8
11 CLK_IN
36 MHz digital clock input, SX1255 used in slave TX mode. · p. 8
12 Q_IN
Digital baseband data input for I (inphase) channel DAC. · p. 8
13 I_IN
Digital baseband data input for Q (quadrature) channel DAC. · p. 8
14 Q_OUT
Digital baseband data output from I (inphase) channel ADC. · p. 8
15 I_OUT
Digital baseband data output from Q (quadrature) channel ADC. · p. 8
16 VBAT2
VBAT supply voltage. · p. 8
17 SCK
SPI clock. · p. 8
18 MISO
Master In Slave Output SPI output. · p. 8
19 MOSI
Master Out Slave Input SPI input. · p. 8
20 NSS
SPI chip select. · p. 8
21 DIO0
Digital I/O, software configured. · p. 8
22 DIO1
Digital I/O, software configured. · p. 8
23 DIO2
Digital I/O, software configured. · p. 8
24 DIO3
Digital I/O, software configured. · p. 8
25 VR_ANA2
Regulated supply for analog RX circuit. · p. 8
26 GND
Ground. · p. 8
27 RF_IN
RX LNA input. · p. 8
28 GND
Ground. · p. 8
29 RF_ON
Differential TX Output, negative node. · p. 8
30 RF_OP
Differential TX Output, positive node. · p. 8
31 GND
Ground. · p. 8
32 VBAT3
VBAT supply for TX amplifier. · p. 8

Ordering codes, by the datasheet

2
SX1255IWLTRT
MLPQW-32 · -40 to +85 C; 3000 per reel · p. 1
SX1255WS
- · -40 to +85 C; 1 Wafer · p. 1

Open-source boards using it

8
  • 2 layers65 × 30 mmSX1255 HAT hw, the printed circuit board in 3D

    SX1255 HAT hw

    M17-Project/SX1255_HAT-hw

    Raspberry Pi Zero shield with the SX1255 RF transceiver chip

    32 parts47
  • 4 layers65 × 30 mmMu cell bb, the printed circuit board in 3D

    Mu cell bb

    Jankyneering/mu-cell

    An open-source SDR base station

    85 parts22CC-BY-SA-4.0
  • 2 layers65 × 56.3 mmHAT with PA, the printed circuit board in 3D

    HAT with PA

    labdvm/SX1255-Tetra-TMO-HS-HAT

    Modified sdr transciever for digital and analog modes include Tetra-TMO

    89 parts13
  • 2 layers65 × 30 mmSX1255 HAT, the printed circuit board in 3D

    SX1255 HAT

    Jankyneering/SX1255_dev_hat

    Raspberry Pi Zero shield with the SX1255 RF transceiver chip. Based on M17's design.

    42 parts2CC-BY-SA-4.0
  • 2 layers65 × 56.3 mmHAT without PA, the printed circuit board in 3D

    HAT without PA

    labdvm/SX1255-Tetra-TMO-HS-HAT

    Modified sdr transciever for digital and analog modes include Tetra-TMO

    84 parts13
  • 6 layers31 × 30 mmSx1255-breakout, the printed circuit board in 3D

    Sx1255-breakout

    MTalon63/PCBs

    Misc. PCB designs

    17 parts2
  • 2 layers22.5 × 37.5 mmSx1255-breakout, the printed circuit board in 3D

    Sx1255-breakout

    MTalon63/PCBs

    Misc. PCB designs

    23 parts2
  • 2 layers65 × 30 mmLoRaFlux RF HAT, the printed circuit board in 3D

    LoRaFlux RF HAT

    MAHESH-THILAK-K/ADDITIONAL-PROJECT

    34 parts1Apache-2.0

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the SX1255IWLTRT?

Yes. The symbol is EasyEDA_Cloud:SX1255IWLTRT and the footprint EasyEDA_Cloud:QFN-32_L5.0-W5.0-P0.50-BL-EP3.1, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the SX1255IWLTRT?

QFN-32-EP(5x5), with 33 pins. Its footprint is drawn on this page.

Where is the SX1255IWLTRT datasheet?

SEMTECH publishes it: the Datasheet link on this page opens it.

Where can I order the SX1255IWLTRT?

JLCPCB lists it as part C89372, with 68 in stock; the sellers' links on this page open their listings.

What can replace the SX1255IWLTRT?

Parts like it in the library: the SX1211I084TRT by SEMTECH. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the SX1255IWLTRT?

8 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.