Skip to the content
12345678

PCA9517ADP

NXP SemiconductorsExtended

-40℃~+85℃ 2 2-Wire Bus 2-Wire Bus 2.7V~5.5V 400Kbps 6pF Auto-enable、Level shifting、Bus capacitance isolation、Hot-swap protection Driver、Buffer MSOP-8 Signal Buffers, Repeaters, Splitters ROHS

Part id
nxp/PCA9517ADP
Category
Signal Buffers, Repeaters, Splitters
Package
MSOP-8
Pins
8
In stock
63,172 at JLCPCB (C80799)
Used on
3 open-source boards

Overview

The PCA9517ADP is a signal Buffers, Repeaters, Splitter made by NXP Semiconductors in a MSOP-8 package with 8 pins. -40℃~+85℃ 2 2-Wire Bus 2-Wire Bus 2.7V~5.5V 400Kbps 6pF Auto-enable、Level shifting、Bus capacitance isolation、Hot-swap protection Driver、Buffer MSOP-8 Signal Buffers, Repeaters, Splitters ROHS.

PCBKit's library has its KiCad symbol (Analog & Interface:PCA9517AD, from CERN's library) and its footprint (Package_SO:MSOP-8_3x3mm_P0.65mm, from KiCad's library), ready for a KiCad board. 63,172 are in stock at JLCPCB (part C80799). 3 open-source boards in 2 repositories on GitHub use it.

Symbol

3SDAA2SCLA5EN1VCCA6SDAB7SCLB8VCCB4GND
Analog & Interface:PCA9517ADFrom CERN's library

Footprint

12345678
Package_SO:MSOP-8_3x3mm_P0.65mmFrom KiCad's library

From the datasheet

10
Supply, least
900 mV · VCC(A), recommended operating min · p. 10
Supply, most
5.5 V · VCC(A), recommended operating max · p. 10
Supply, least
2.7 V · VCC(B), recommended operating min · p. 10
Supply, absolute maximum
7 V · VCC(A), absolute max · p. 9
Works from
-40 °C · Ambient operating in free air min · p. 9
Works up to
85 °C · Ambient operating in free air max · p. 9
Junction, hottest
125 °C · Junction temperature absolute max · p. 9
Takes working
6 mA · sum of VCC(A) and VCC(B) supply currents, both channels HIGH, max · p. 10
A pin gives at most
50 mA · Port A or B input/output current absolute max · p. 9
Edge
20 ns · Port A LOW to HIGH output transition, typical · p. 11

What it is and has

10
Function
Level translating I2C-bus repeater · p. 1
Channels
2 bidirectional buffers; 400 pF on either side · p. 2
Interfaces
I2C-bus and SMBus · p. 2
Enable
Active HIGH · p. 2
I/O
Open-drain · p. 2
Bus features
Arbitration and clock stretching · p. 2
Powered-off behavior
High-impedance I2C-bus pins · p. 2
Clock frequency
0 Hz to 400 kHz; system frequency may be lower due to repeater delays · p. 2
ESD protection
Exceeds 5500 V HBM and 1000 V CDM · p. 2
Package options
SO8, TSSOP8 and HWSON8 · p. 2

Around it

3
res 10 kΩ
between SDAA and VCC(A); Port A pull-up in typical application. · p. 5
res 75 Ω
between SDAA and cable SDA; Series resistor in short-cable application. · p. 8
res 10 kΩ
between EN and VCC(B); Optional pull-up in short-cable application. · p. 8

Specifications

51
ParameterConditionsAs printedPage
electrostatic discharge, HBMPCA9517A; exceeds stated valuemin 5.5 kV1
supply voltage port B VCC(B)2.7 V to 5.5 Vmin -0.5 · max 7 V9
supply voltage port A VCC(A)adjustablemin -0.5 · max 7 V9
voltage on an input/output pin VI/Oport A and port B; enable pin (EN)min -0.5 · max 7 V9
input/output current II/Oport A; port Bmax 50 mA9
input current IIEN, VCC(A), VCC(B), GNDmax 50 mA9
total power dissipation Ptotmax 100 mW9
storage temperature Tstgmin -55 · max 125 C9
ambient temperature Tamboperating in free airmin -40 · max 85 C9
junction temperature Tjmax 125 C9
supply voltage port B VCC(B)min 2.7 · max 5.5 V10
supply voltage port A VCC(A)LOW-level supply voltagemin 0.9 · max 5.5 V10
supply current on pin VCC(A) ICC(VCC(A))max 1 mA10
HIGH-level supply current ICCHboth channels HIGH; VCC = 5.5 V; SDAn = SCLn = VCCtyp 1.5 · max 5 mA10
LOW-level supply current ICCLboth channels LOW; VCC = 5.5 V; one SDA and one SCL = GND; other SDA and SCL opentyp 1.5 · max 5 mA10
contention port A supply current ICC(A)cVCC = 5.5 V; SDAn = SCLn = VCCtyp 1.5 · max 5 mA10
HIGH-level input voltage VIHSDAB and SCLBmax 5.5 V10
LOW-level input voltage VILSDAB and SCLB; first LOW levelmin -0.5 V10
contention LOW-level input voltage VILcSDAB and SCLB; second and subsequent LOW levelsmin -0.5 · typ 0.4 V10
input clamping voltage VIKSDAB and SCLB; II = 18 mAmax -1.2 V10
LOW-level input current IILSDAB and SCLB; SDA, SCL; VI = 0.2 Vmax 10 A10
LOW-level output voltage VOLSDAB and SCLB; IOL = 100 A or 6 mAmin 0.47 · typ 0.52 · max 0.6 V10
difference between LOW-level output and LOW-level input voltage contention VOLVILcSDAB and SCLB; guaranteed by designmax 70 mV10
HIGH-level output leakage current ILOHSDAB and SCLB; VO = 3.6 Vmax 10 A10
input/output capacitance CioSDAB and SCLB; VI = 3 V or 0 V; VCC = 3.3 Vtyp 6 · max 7 pF10
input/output capacitance CioSDAB and SCLB; VI = 3 V or 0 V; VCC = 0 Vtyp 6 · max 7 pF10
HIGH-level input voltage VIHSDAA and SCLAmax 5.5 V10
LOW-level input voltage VILSDAA and SCLA; with envelope noise must be below 0.3VCC(A)min -0.5 V10
input clamping voltage VIKSDAA and SCLA; II = 18 mAmax -1.2 V10
LOW-level input current IILSDAA and SCLA; SDA, SCL; VI = 0.2 Vmax 10 A10
LOW-level output voltage VOLSDAA and SCLA; IOL = 6 mAtyp 0.1 · max 0.2 V10
HIGH-level output leakage current ILOHSDAA and SCLA; VO = 3.6 Vmax 10 A10
input/output capacitance CioSDAA and SCLA; VI = 3 V or 0 V; VCC = 3.3 Vtyp 6 · max 7 pF10
input/output capacitance CioSDAA and SCLA; VI = 3 V or 0 V; VCC = 0 Vtyp 6 · max 7 pF10
LOW-level input voltage VILEnablemin -0.5 V11
HIGH-level input voltage VIHEnablemax 5.5 V11
LOW-level input current on pin EN IIL(EN)VI = 0.2 V, EN; VCC = 3.6 Vtyp -10 · max -30 A11
input leakage current ILIEnablemin -1 · max 1 A11
input capacitance CiEnable; VI = 3.0 V or 0 Vtyp 6 · max 7 pF11
LOW to HIGH propagation delay tPLHport B to port A; Figure 13min 100 · typ 170 · max 250 ns11
HIGH to LOW propagation delay tPHLport B to port A; Figure 11; VCC(A)  2.7 Vmin 30 · typ 80 · max 110 ns11
HIGH to LOW propagation delay tPHLport B to port A; Figure 11; VCC(A)  3 Vmin 10 · typ 66 · max 300 ns11
LOW to HIGH output transition time tTLHport A; Figure 11min 10 · typ 20 · max 30 ns11
HIGH to LOW output transition time tTHLport A; Figure 11; VCC(A)  2.7 Vmin 1 · typ 77 · max 105 ns11
HIGH to LOW output transition time tTHLport A; Figure 11; VCC(A)  3 Vmin 20 · typ 70 · max 175 ns11
LOW to HIGH propagation delay tPLHport A to port B; Figure 12min 25 · typ 53 · max 110 ns11
HIGH to LOW propagation delay tPHLport A to port B; Figure 12min 60 · typ 79 · max 230 ns11
LOW to HIGH output transition time tTLHport B; Figure 12min 120 · typ 140 · max 170 ns11
HIGH to LOW output transition time tTHLport B; Figure 12min 30 · typ 48 · max 90 ns11
set-up time tsuEN HIGH before START conditionmin 100 ns11
hold time thEN HIGH after STOP conditionmin 100 ns11

Pins, by the datasheet

8
1 VCC(A)
Port A supply voltage (0.9 V to 5.5 V). · p. 4
2 SCLA
Serial clock port A bus. · p. 4
3 SDAA
Serial data port A bus. · p. 4
4 GND
Supply ground (0 V). · p. 4
5 EN
Active HIGH repeater enable input. · p. 4
6 SDAB
Serial data port B bus. · p. 4
7 SCLB
Serial clock port B bus. · p. 4
8 VCC(B)
Port B supply voltage (2.7 V to 5.5 V). · p. 4

Ordering codes, by the datasheet

4
PCA9517AD
SO8 · 8-lead package; body width 3.9 mm; SOT96-1. · p. 2
PCA9517ADP
TSSOP8 (MSOP8) · 8-lead package; body width 3 mm; SOT505-1. · p. 2
PCA9517ADP/DG
TSSOP8 (MSOP8) · Electrically and mechanically equivalent to PCA9517ADP; initially produced with Dark Green package material. · p. 2
PCA9517ATP
HWSON8 · 8-terminal leadless package; body 2 × 3 × 0.8 mm; SOT1069-2. · p. 2

Open-source boards using it

3
  • 8 layers78 × 55 mmJetson AI Cam CopperPilot, the printed circuit board in 3D

    Jetson AI Cam CopperPilot

    CopperPilot/Jetson-AI-Cam-CopperPilot

    A carrier for Jetson Nano, Xavier NX and TX2 NX with two IMX219 cameras on a 39 mm stereo baseline, dual 4K outputs and CAN.

    305 parts15
  • 2 layers88.9 × 50.8 mmSSM3582, the printed circuit board in 3D

    SSM3582

    matt-txrx/HI-FI-USB-AUDIO-KIT

    45 parts1
  • 2 layers88.9 × 50.8 mmSSM3582 v02, the printed circuit board in 3D

    SSM3582 v02

    matt-txrx/HI-FI-USB-AUDIO-KIT

    45 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the PCA9517ADP?

Yes. The symbol is Analog & Interface:PCA9517AD and the footprint Package_SO:MSOP-8_3x3mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the PCA9517ADP?

MSOP-8, with 8 pins. Its footprint is drawn on this page.

Where is the PCA9517ADP datasheet?

NXP Semiconductors publishes it: the Datasheet link on this page opens it.

Where can I order the PCA9517ADP?

JLCPCB lists it as part C80799, with 63,172 in stock; the sellers' links on this page open their listings.

What can replace the PCA9517ADP?

Parts like it in the library: the TCA4311ADGK by Texas Instruments, the PI6ULS5V9617AUEX by Diodes Incorporated, the P82B96DGKR by Texas Instruments and the PCA9515BDGK by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the PCA9517ADP?

3 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.