Skip to the content
12345678PAD

TP4056-MS

MSKSEMIExtended

-40℃~+85℃ 1 1A 4.2V 4.2V~5.5V 70uA Charging IC Constant current charging、Constant voltage charging、Trickle charging、Automatic recharge、Charge termination、Programmable charging current、Soft-start、Under-voltage lockout Lithium Battery Support SOP-8-EP Battery Management ROHS

Part id
msksemi/TP4056-MS
Category
Battery Management
Package
SOP-8-EP
Pins
9
In stock
119,981 at JLCPCB (C7473158)
Used on
10 open-source boards

Overview

The TP4056-MS is a battery Management made by MSKSEMI in a SOP-8-EP package with 9 pins. -40℃~+85℃ 1 1A 4.2V 4.2V~5.5V 70uA Charging IC Constant current charging、Constant voltage charging、Trickle charging、Automatic recharge、Charge termination、Programmable charging current、Soft-start、Under-voltage lockout Lithium Battery Support SOP-8-EP Battery Management ROHS.

PCBKit's library has its KiCad symbol (pimoroni-ics:TP4056, from Eagle libraries) and its footprint (pimoroni-ics:SO08-PAD-300, from Eagle libraries), ready for a KiCad board. 119,981 are in stock at JLCPCB (part C7473158). 10 open-source boards in 6 repositories on GitHub use it.

Symbol

4VCC8CE7CHRG6STDBY5BAT1TEMP2PROG3GNDPADGND
pimoroni-ics:TP4056From Eagle libraries

Footprint

12345678PAD
pimoroni-ics:SO08-PAD-300From Eagle libraries

From the datasheet

11
Supply, least
4.2 V · VCC, recommended operating min · p. 4
Supply, most
9 V · VCC, recommended operating max · p. 4
Supply, absolute maximum
9 V · VCC, absolute max · p. 2
Works from
-40 °C · Operating ambient min · p. 2
Works up to
85 °C · Operating ambient max · p. 2
Junction, hottest
145 °C · Junction temperature absolute max · p. 2
Takes working
150 µA · VCC charging-mode own supply current typical, RPROG=1K · p. 4
Takes asleep
70 µA · VCC standby current typical, charging terminated · p. 4
Gives
1 A · Programmable charging current max · p. 2
A pin gives at most
1 mA · PROG pin current absolute max · p. 2
Output
4.2 V · Fixed float voltage typical · p. 12

What it is and has

12
Charging current
Programmable up to 1000mA · p. 2
Charging mode
Constant current / constant voltage · p. 2
Thermal regulation
Temperature-adaptive charging rate · p. 2
Automatic recharge
Supported · p. 2
Protection
Lithium battery reverse-polarity protection · p. 2
Supply adaptation
Supported · p. 2
Status indication
Dual charging status outputs; battery absence and fault indication · p. 2
Charge termination
C/10 · p. 2
Trickle charging
2.9V threshold · p. 2
Soft start
Limits inrush current · p. 2
Battery temperature monitoring
Supported · p. 2
Package
8-pin SOP-8-EP with thermal pad · p. 2

Around it

2
res Selected for required charging current
between PROG and GND; RPROG programs the charging current. · p. 6
res 0.5 欧姆
between Input supply and VCC; Recommended for larger charging currents to reduce chip heating; use size 1206 or larger. · p. 9

Specifications

45
ParameterConditionsAs printedPage
输入电源电压 VCCmin -0.3 · max 9 V2
PROG PROGUpper limit VCC+0.3Vmin -0.3 V2
BAT BATmin -4.35 · max 7 V2
CHRG CHRGmin -0.3 · max 10 V2
STDBY STDBYmin -0.3 · max 10 V2
TEMP TEMPmin -0.3 · max 10 V2
CE CEmin -0.3 · max 10 V2
PROG 引脚电流max 1000 uA2
最大结温max 145 ℃2
工作环境温度范围min -40 · max 85 ℃2
贮存温度范围min -65 · max 125 ℃2
引脚温度焊接时间 10 秒max 260 ℃2
输入电源电压 VCC整个工作温度范围min 4.2 · typ 5 · max 9 V4
输入电源电流 ICC充电模式,RPROG=1K;整个工作温度范围;VCC=5Vtyp 150 · max 500 uA4
输入电源电流 ICC待机模式 (充电终止);整个工作温度范围;VCC=5Vtyp 70 · max 120 uA4
输入电源电流 ICC停机模式 (RPROG 未连,VCC<VBAT,或 VCC<VUV);整个工作温度范围typ 70 · max 120 uA4
稳 定 输出 (浮充) 电压 VFLOALTP4056-MS,4.2V;0℃≤TA≤85℃;VCC=5Vmin 4.158 · typ 4.2 · max 4.242 V4
BAT 引脚电流 IBATRPROG=2K,电流模式,VBAT=4.0V;整个工作温度范围;VCC=5Vmin 450 · typ 500 · max 550 mA4
BAT 引脚电流 IBATRPROG=1K,电流模式,VBAT=4.0V;整个工作温度范围;VCC=5Vmin 950 · typ 1000 · max 1060 mA4
BAT 引脚电流 IBAT待机模式,VBAT=VFLOAL;整个工作温度范围;VCC=5Vmin 0 · typ -2 · max -6 uA4
BAT 引脚电流 IBAT停机模式 (RPROG 未连);TA=25℃,VCC=5V;typ ±1,max ±2typ 1 · max 2 uA4
BAT 引脚电流 IBAT睡眠模式,VCC=0V;TA=25℃typ -1 · max -2 uA4
涓 流充 电电 流 ITRIKLVBAT<VTRIKL,RPROG=1k;整个工作温度范围;VCC=5Vmin 200 · typ 230 · max 260 mA4
涓流充电门限电压 VTRIKLRPROG=1k,VBAT 上升;TA=25℃,VCC=5Vmin 2.8 · typ 2.9 · max 3 V4
涓流充电迟滞电压 VTRHYSRPROG=1k;TA=25℃,VCC=5Vmin 60 · typ 80 · max 100 mV4
VCC 欠 压 闭 锁 门 限 V UV从 VCC 低至高;整个工作温度范围typ 3.6 V4
VCC 欠 压 闭 锁 迟 滞 VUVHYS整个工作温度范围min 150 · typ 200 · max 300 mV4
VCC-VBAT 闭 锁 门 限 电 压 VASDVCC 从低到高;TA=25℃min 60 · typ 100 · max 140 mV4
VCC-VBAT 闭 锁 门 限 电 压 VASDVCC 从高到低;TA=25℃min 5 · typ 30 · max 50 mV4
C/ 10 终止电流门限 ITERMRPROG=2.4K;整个工作温度范围;VCC=5Vmin 60 · typ 70 · max 80 mA4
C/ 10 终止电流门限 ITERMRPROG=1k;整个工作温度范围;VCC=5Vmin 120 · typ 130 · max 140 mA4
PROG 引 脚 电 压 VPROGRPROG=1k,电流模式;整个工作温度范围;VCC=5Vmin 0.9 · typ 1 · max 1.1 V4
CHRG 引脚输出低电压 CHRGICHRG = 5 mA;TA=25℃,VCC=5Vtyp 0.3 · max 0.6 V4
STDBY 引 脚 输 出 低 电 平 STDBYISTDBY =5 mA;TA=25℃,VCC=5Vtyp 0.3 · max 0.6 V4
TEMP 引 脚 高 端 翻 转 电 压 VTEMP- HTA=25℃,VCC=5Vtyp 80 · max 82 %VCC4
TEMP 引 脚 低 端 翻 转 电 压 VTEMP- LTA=25℃,VCC=5Vmin 43 · typ 45 %VCC4
再充电电池门限电压 Δ VRECHRGVFLOAT- VRECHRG;TA=25℃,VCC=5Vmin 80 · typ 110 · max 140 mV4
限定 温度 模式 中的 结温 TLIMTA=25℃,VCC=5Vtyp 145 ℃4
功率 FET“导通”电阻 RON在 VCC 与 BAT 之间;TA=25℃,VCC=5Vtyp 550 mΩ4
软启 动时 间 ts sIBAT=0 至 IBAT=1100V/RPROG;TA=25℃,VCC=5Vtyp 20 us4
再充电比较器滤波时间 RECHARGEVBAT 高至低;TA=25℃,VCC=5Vmin 0.8 · typ 2 · max 4 ms4
终止比较器滤波时间 TERMIBAT 降至 ICHG/10 以下;TA=25℃,VCC=5Vmin 0.8 · typ 2 · max 4 ms4
PROG 引 脚 上 拉 电 流 IPROGTA=25℃,VCC=5Vtyp 2 uA4
Vcc 自 适 应 启 动 电 压 VADPTTA=25℃,VCC=5Vtyp 4.3 V4
电池反向漏电流 IBAT电池反接,VIN=5V;TA=25℃typ 2.5 · max 5 mA4

Pins, by the datasheet

9
1 TEMP
电池温度检测输入端;接地可禁止电池温度监测。 · p. 3
2 PROG
恒流充电电流设置和充电电流监测端。 · p. 3
3 GND
地线。 · p. 3
4 VCC
输入电压正输入端。 · p. 3
5 BAT
电池连接端。 · p. 3
6 STDBY
电池充电完成指示端。 · p. 3
7 CHRG
充电中状态指示端。 · p. 3
8 CE
芯片使能输入端。 · p. 3
EP 散热片焊盘
可接地或者悬空,不可接其他电位。 · p. 3

Ordering codes, by the datasheet

1
TP4056-MS
SOP-8-EP · 4.2V output; tray packing, 4000pcs · p. 12

Open-source boards using it

10See all 10
  • 4 layersCABadge V2 1, the printed circuit board in 3D

    CABadge V2 1

    nbtca/CABadge

    CABadge 计协电子吧唧:基于 ESP32-S3 的开源圆屏互动徽章,支持动态壁纸、触摸交互、Wi-Fi/BLE 和趣味小应用,提供 PCB、3D 打印外壳、固件及配套工具。

    110 parts15MIT
  • 4 layers45 × 34.8 mmKywy Micro, the printed circuit board in 3D

    Kywy Micro

    KOINSLOT-Inc/kywy-hardware

    kywy hardware files

    92 parts1
  • 2 layers190 × 188 mmLi ion charger panel, the printed circuit board in 3D

    Li ion charger panel

    SolderedElectronics/Li-ion-charger-hardware-design

    Hardware design, BOM, gerbers and 3D files for Li-ion-charger designed by Soldered Electronics.

    1,812 parts1
  • 2 layers59 × 70 mmProject draft, the printed circuit board in 3D

    Project draft

    AnnaLukose/EEE3088F-Project-2025-Group-37

    The final design kicad files are available in the KICAD FILES folder. Previous versions are also available in the draft 1 and draft 2 zip folders.

    72 parts
  • 2 layers35 × 70 mmFlightRecorder, the printed circuit board in 3D

    FlightRecorder

    Ash1of1/FlightRecorder

    FR-1 is a standalone rocket telemetry module. It samples pressure/altitude, temperature, acceleration, and gyro data, and serves a live dashboard over its own WiFi network — no internet, router, or app install required.

    37 parts
  • 2 layers61.5 × 100.3 mmStair lights, the printed circuit board in 3D

    Stair lights

    ogruendel/stair-lights

    80 parts
  • 2 layers22 × 38 mmLI ION Charger, the printed circuit board in 3D

    LI ION Charger

    SolderedElectronics/Li-ion-charger-hardware-design

    Hardware design, BOM, gerbers and 3D files for Li-ion-charger designed by Soldered Electronics.

    43 parts1
  • 2 layers38 × 22 mmLI ION Charger, the printed circuit board in 3D

    LI ION Charger

    SolderedElectronics/Li-ion-charger-hardware-design

    Hardware design, BOM, gerbers and 3D files for Li-ion-charger designed by Soldered Electronics.

    43 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TP4056-MS?

Yes. The symbol is pimoroni-ics:TP4056 and the footprint pimoroni-ics:SO08-PAD-300, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TP4056-MS?

SOP-8-EP, with 9 pins. Its footprint is drawn on this page.

Where is the TP4056-MS datasheet?

MSKSEMI publishes it: the Datasheet link on this page opens it.

Where can I order the TP4056-MS?

JLCPCB lists it as part C7473158, with 119,981 in stock; the sellers' links on this page open their listings.

What can replace the TP4056-MS?

Parts like it in the library: the TP4056 by UMW, the TP4056 by JSMSEMI, the TP4056X-42-ESOP8 by TOPPOWER and the TP4056-MS-N1 by MSKSEMI. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TP4056-MS?

10 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.