Skip to the content
12345678910111213

MD1213K6-G

Microchip TechnologyExtended

-40℃~+85℃ 0V~300mV 2 2A 2A 3V~5V 4.5V~13V 550uA 6ns 6ns 7ns 7ns MOSFET QFN-12-EP(4x4) Gate Drivers ROHS

Part id
microchip/MD1213K6-G
Category
Gate Drivers
Package
QFN-12-EP(4x4)
Pins
13
In stock
287 at JLCPCB (C621434)
Used on
5 open-source boards

Overview

The MD1213K6-G is a gate Driver made by Microchip Technology in a QFN-12-EP(4x4) package with 13 pins. -40℃~+85℃ 0V~300mV 2 2A 2A 3V~5V 4.5V~13V 550uA 6ns 6ns 7ns 7ns MOSFET QFN-12-EP(4x4) Gate Drivers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:MD1210K6-G, from EasyEDA) and its footprint (EasyEDA_Cloud:QFN-12_L4.0-W4.0-P0.80-BL-EP1.7, from EasyEDA), ready for a KiCad board. 287 are in stock at JLCPCB (part C621434). 5 open-source boards in 3 repositories on GitHub use it.

Symbol

1INA2VL3INB4GND5VSS16VSS27OUTB8VH9OUTA10VDD211VDD112OE13EP
EasyEDA_Cloud:MD1210K6-GFrom EasyEDA

Footprint

12345678910111213
EasyEDA_Cloud:QFN-12_L4.0-W4.0-P0.80-BL-EP1.7From EasyEDA

From the datasheet

12
Supply, least
4.5 V · VDD–VSS, recommended operating min; 2.5V ≤ VDD ≤ 13V · p. 4
Supply, most
13 V · VDD–VSS, recommended operating max; 2.5V ≤ VDD ≤ 13V · p. 4
Supply, least
5.5 V · VSS, recommended operating min · p. 4
Supply, absolute maximum
13.5 V · VDD–VSS, absolute max · p. 4
Supply, absolute maximum
500 mV · VSS, absolute max · p. 4
Works from
-40 °C · operating ambient min · p. 5
Works up to
85 °C · operating ambient max · p. 5
Junction, hottest
125 °C · junction temperature max · p. 5
Takes working
30.48 mA · sum of VDD1, VDD2 and VH typical average currents; one channel at 5 MHz, no load · p. 4
Edge
6 ns · output rise time typical; CLOAD = 1000 pF · p. 5
Junction to air (12-lead QFN)
47 K/W · typical; 1 oz. 4-layer 3” x 4” PCB with thermal pad and thermal via array · p. 5
Junction to case (12-lead QFN)
7 K/W · thermal resistance to case typical · p. 5

What it is and has

8
Output timing
6 ns rise and fall time with 1000 pF load · p. 1
Peak output current
2 A source and sink · p. 1
Logic compatibility
1.8 V to 5 V CMOS · p. 1
Supply voltage
4.5 V to 13 V total · p. 1
Logic threshold
Smart logic threshold · p. 1
Channels
Two matched channels · p. 1
Output swing
Can swing below ground · p. 1
Package
12-lead QFN · p. 12

Around it

2
cap not specified
between VDD1 and GND; Ceramic bypass capacitor to the ground plane with short leads; place close to supply pins. A common capacitor may serve VDD1 and VDD2. · p. 8
cap up to 1 µF
between VH and GND; Ceramic bypass capacitor next to the chip pin; a series ferrite bead may prevent supply-lead resonance. · p. 8

Specifications

39
ParameterConditionsAs printedPage
Level Translator Supply Voltage VDD–VSSmin -0.5 · max 13.5 V4
Low-Side Supply Voltage VSSmin -7 · max 0.5 V4
Maximum Junction Temperature TJmax 125 °C4
Operating Ambient Temperature TAmin -40 · max 85 °C4
Storage Temperature TSmin -65 · max 150 °C4
Level Translator Supply Voltage VDD–VSS2.5V ≤ VDD ≤ 13Vmin 4.5 · max 13 V4
Level Translator Negative Supply Voltage VSSmin -5.5 · max 0 V4
VDD1 Quiescent Current IDD1QNo input transitionstyp 0.55 mA4
VDD2 Quiescent Current IDD2QNo input transitionsmax 10 uA4
VH Quiescent Current IHQNo input transitionsmax 10 uA4
VDD1 Average Current IDD1One channel on at 5 MHz, no loadtyp 0.88 mA4
VDD2 Average Current IDD2One channel on at 5 MHz, no loadtyp 6.6 mA4
VH Average Current IHOne channel on at 5 MHz, no loadtyp 23 mA4
Input Logic Voltage High VIHFor logic inputs INA and INB; Min. VOE–0.3max 5 V4
Input logic Voltage Low VILFor logic inputs INA and INBmin 0 · max 0.3 V4
Input Logic Current High IIHFor logic inputs INA and INBmax 1 uA4
Input Logic Current Low IILFor logic inputs INA and INBmax 1 uA4
OE Input Logic Voltage High VIHFor logic input OEmin 1.8 · max 5 V4
OE Input Logic Voltage Low VILFor logic input OEmin 0 · max 0.3 V4
OE Input Logic Impedance to GND RINFor logic input OEmin 12 · typ 20 · max 30 KΩ4
Logic Input Capacitance CINAll inputstyp 5 · max 10 pF4
Output Sink Resistance RSINKISINK = 50 mAmax 12.5 Ω4
Output Source Resistance RSOURCEISOURCE = 50 mAmax 12.5 Ω4
Peak Output Sink Current ISINKtyp 2 A4
Peak Output Source Current ISOURCEtyp 2 A4
Inputs or OE Rise and Fall Time tirfLogic input edge speed requirementmax 10 ns5
Propagation Delay when Output is from Low to High tPLHCLOAD = 1000 pF, input signal rise/fall time of 2 ns (See Timing Diagram and Figure 3-1.)typ 7 ns5
Propagation Delay when Output is from High to Low tPHLCLOAD = 1000 pF, input signal rise/fall time of 2 ns (See Timing Diagram and Figure 3-1.)typ 7 ns5
Propagation Delay OE to Outputs tPOECLOAD = 1000 pF, input signal rise/fall time of 2 ns (See Timing Diagram.)typ 9 ns5
Output Rise Time trCLOAD = 1000 pF, input signal rise/fall time of 2 ns (See Timing Diagram.)typ 6 ns5
Output Fall Time tfCLOAD = 1000 pF, input signal rise/fall time of 2 ns (See Timing Diagram.)typ 6 ns5
Rise and Fall Time Matching l tr–tf lFor each channeltyp 1 ns5
Propagation Low to High and High-to-low Matching l tPLH–tPHL lFor each channeltyp 1 ns5
Propagation Delay Match ∆tdmDevice-to-device delay matchtyp 2 ns5
Maximum Junction Temperature TJmax 125 °C5
Operating Ambient Temperature TAmin -40 · max 85 °C5
Storage Temperature TSmin -65 · max 150 °C5
12-lead QFN JA12-lead QFN; Note 1: On an 1 oz. 4-layer 3” x 4” PCB with thermal pad and thermal via arraytyp 47 °C/W5
Thermal Resistance to Case θJC12-lead QFNtyp 7 °C/W5

Pins, by the datasheet

13
1 INA
Controls OUTA when OE is high; input high drives VL and input low drives VH. · p. 7
2 VL
Supply voltage for N-channel output stage. · p. 7
3 INB
Controls OUTB when OE is high; input high drives VL and input low drives VH. · p. 7
4 GND
Logic input ground reference. · p. 7
5 VSS1
Low-side analog circuit and level translator supply; must be at the lowest chip potential and connected externally to the thermal pad. · p. 7
6 VSS2
Low-side gate drive supply; should be at the same potential as VSS1. · p. 7
7 OUTB
Drives an external N-channel MOSFET gate through a series capacitor; swings between VH and VL and goes to VL when OE is low. · p. 7
8 VH
Supply voltage for P-channel output stage. · p. 7
9 OUTA
Drives an external P-channel MOSFET gate through a series capacitor; swings between VH and VL and goes to VH when OE is low. · p. 7
10 VDD2
High-side gate drive supply voltage. · p. 7
11 VDD1
High-side analog circuit and level shifter supply; should be at the same potential as VDD2. · p. 7
12 OE
Output enable; when high, (VOE + VGND)/2 sets the INA and INB logic threshold; when low, OUTA is VH and OUTB is VL. · p. 7
Thermal Pad Thermal Pad
Index pad and thermal pad are internally connected; connect externally to VSS1 at pin 5. · p. 7

Ordering codes, by the datasheet

1
MD1213K6-G
12-lead (4x4) QFN · Lead (Pb)-free/RoHS-compliant; 5000/Reel · p. 12

Open-source boards using it

5
  • 4 layers87.1 × 78.2 mm3 in 1 Panel, the printed circuit board in 3D

    3 in 1 Panel

    kelu124/pic0rick

    An rp2040-based acquisition board for pulse-echo ultrasound

    115 parts116
  • 4 layers120 × 80 mmUltr4rick, the printed circuit board in 3D

    Ultr4rick

    kelu124/ultr4rick

    High-end version of the pic0rick

    269 parts4
  • 4 layers200 × 100 mmMinUS, the printed circuit board in 3D

    MinUS

    kelu124/minus

    Minimal ultrasound platform

    222 parts3
  • 2 layers87 × 22.3 mmPanel, the printed circuit board in 3D

    Panel

    kelu124/pic0rick

    An rp2040-based acquisition board for pulse-echo ultrasound

    46 parts116
  • 2 layers63.3 × 22.3 mmPMOD Pulser update, the printed circuit board in 3D

    PMOD Pulser update

    kelu124/pic0rick

    An rp2040-based acquisition board for pulse-echo ultrasound

    33 parts116

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the MD1213K6-G?

Yes. The symbol is EasyEDA_Cloud:MD1210K6-G and the footprint EasyEDA_Cloud:QFN-12_L4.0-W4.0-P0.80-BL-EP1.7, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MD1213K6-G?

QFN-12-EP(4x4), with 13 pins. Its footprint is drawn on this page.

Where is the MD1213K6-G datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MD1213K6-G?

JLCPCB lists it as part C621434, with 287 in stock; the sellers' links on this page open their listings.

What can replace the MD1213K6-G?

Parts like it in the library: the MD1210K6-G by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MD1213K6-G?

5 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.