Skip to the content
12345678

MCP9808-E/MS

Microchip TechnologyExtended

-40℃~+125℃ 13bit 2.7V~5.5V 250ms I2C、SMBus ±0.5℃ MSOP-8 Temperature Sensors ROHS

Part id
microchip/MCP9808-E/MS
Category
Temperature Sensors
Package
MSOP-8
Pins
8
In stock
531 at JLCPCB (C129490)
Used on
27 open-source boards

Overview

The MCP9808-E/MS is a temperature Sensor made by Microchip Technology in a MSOP-8 package with 8 pins. -40℃~+125℃ 13bit 2.7V~5.5V 250ms I2C、SMBus ±0.5℃ MSOP-8 Temperature Sensors ROHS.

PCBKit's library has its KiCad symbol (Sensors:MCP9808-E/MS, from CERN's library) and its footprint (Package_SO:MSOP-8_3x3mm_P0.65mm, from KiCad's library), ready for a KiCad board. 531 are in stock at JLCPCB (part C129490). 27 open-source boards in 23 repositories on GitHub use it.

Symbol

1SDA2SCL5A26A17A03ALERT8VDD4GND
Sensors:MCP9808-E/MSFrom CERN's library

Footprint

12345678
Package_SO:MSOP-8_3x3mm_P0.65mmFrom KiCad's library

From the datasheet

10
Supply, least
2.7 V · VDD, recommended operating min · p. 3
Supply, most
5.5 V · VDD, recommended operating max · p. 3
Supply, absolute maximum
6 V · VDD, absolute max · p. 3
Works from
-40 °C · TA, operating min · p. 4
Works up to
125 °C · TA, operating max · p. 4
Junction, hottest
150 °C · TJ, absolute max · p. 3
Takes working
200 µA · VDD, operating typical · p. 3
Takes at most
400 µA · VDD, operating max · p. 3
Takes asleep
100 nA · VDD, shutdown typical · p. 3
Junction to air (8 引脚 MSOP)
211 K/W · junction to ambient typical · p. 4

What it is and has

6
Temperature accuracy
±0.25°C typical, -40°C to +125°C · p. 1
Temperature accuracy
±0.5°C maximum, -20°C to 100°C · p. 1
Temperature accuracy
±1°C maximum, -40°C to +125°C · p. 1
Measurement resolution
Selectable: +0.5°C, +0.25°C, +0.125°C, +0.0625°C · p. 1
Interface
2-wire I2C/SMBus · p. 1
Package options
2x3 DFN-8, MSOP-8 · p. 1

Around it

1
cap 0.1 µF 至 1 µF
between VDD and GND; Recommended high-frequency ceramic decoupling capacitor, placed as close as possible to the supply and ground pins. · p. 35

Specifications

32
ParameterConditionsAs printedPage
VDD VDDmax 6 V3
所有输入 / 输出引脚上的电压Lower limit: GND – 0.3Vmax 6 V3
储存温度min -65 · max 150 °C3
环境温度 (施加电源时)min -40 · max 125 °C3
结温 TJmax 150 °C3
所有引脚上的 ESD 保护HBMmax 4 kV3
所有引脚上的 ESD 保护MMmax 400 V3
每个引脚上的闩锁电流+25°C; ±200 mAmin -200 · max 200 mA3
温度传感器精度 TACY-20°C < TA ≤ +100°C; VDD = 3.3V; typical ±0.25°Cmin -0.5 · typ 0.25 · max 0.5 °C3
温度传感器精度 TACY-40°C < TA ≤ +125°C; VDD = 3.3V; typical ±0.25°Cmin -1 · typ 0.25 · max 1 °C3
温度转换时间 tCONV0.5°C/ 位; 33s/ 秒 (典型值)typ 30 ms3
温度转换时间 tCONV0.25°C/ 位; 15s/ 秒 (典型值)typ 65 ms3
温度转换时间 tCONV0.125°C/ 位; 7s/ 秒 (典型值)typ 130 ms3
温度转换时间 tCONV0.0625°C/ 位; 4s/ 秒 (典型值)typ 250 ms3
工作电压范围 VDDmin 2.7 · max 5.5 V3
工作电流 IDDtyp 200 · max 400 uA3
关断电流 ISHDNtyp 0.1 · max 2 uA3
上电复位 VPOR下降 VDD 的阈值typ 2.2 V3
电源抑制 Δ°C/ΔVDDVDD = 2.7V 至 5.5V, TA = +25°Ctyp -0.1 °C/V3
高电平电流 (泄漏电流) IOH报警输出; VOH = VDD (低电平有效,上拉电阻)max 1 uA3
低电平电压 VOL报警输出; IOL= 3 mA (低电平有效,上拉电阻)max 0.4 V3
热响应,从 +25°C (空气)至 +125°C (油浴) tRES8 引脚 MSOP; 达到 63% (+89°C)的时间typ 1.4 s3
输入电流 IINSCL、 SDA、 A0、 A1 和 A2; max ±5 uAmax 5 uA4
低电平电压 VOLSDA; IOL= 3 mAmax 0.4 V4
高电平电流 (泄漏电流) IOHSDA; VOH = 5.5Vmax 1 uA4
低电平电流 IOLSDA; VOL = 0.6Vmin 6 mA4
尖峰脉冲抑制 tSPSDA 和 SCL 输入max 50 ns4
电容 CINSDA 和 SCL 输入typ 5 pF4
规定温度范围 TA注 1:在该范围内工作时,不能使 TJ 超出最高结温 (+150°C)。min -40 · max 125 °C4
工作温度范围 TAmin -40 · max 125 °C4
储存温度范围 TAmin -65 · max 150 °C4
热阻, 8 引脚 MSOP θJA8 引脚 MSOPtyp 211 °C/W4

Open-source boards using it

27See all 27
  • 4 layers72.4 × 95.3 mmDingoPDM, the printed circuit board in 3D

    DingoPDM

    corygrant/dingoPDM

    Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are available or the design can be used to build a DIY version.

    156 parts128MIT
  • 4 layers100 × 75 mmOpenHW DevKit, the printed circuit board in 3D

    OpenHW DevKit

    openhwfoundation/core-v-mcu-devkit

    This is the CORE-V MCU DevKit project, hosting the open-source artifacts for the CORE-V MCU Development Kit.

    235 parts18
  • 4 layers60 × 60 mmBLDC, the printed circuit board in 3D

    BLDC

    BetzDrive/bldc-controller-hardware

    Hardware design files for BLDC servo controller

    124 parts14
  • 4 layers42 × 42 mmDynossat edu obc, the printed circuit board in 3D

    Dynossat edu obc

    BHDynamics/dynossat-edu-obc

    DynOSSAT-EDU, educational PocketQube satellite On-Board Computer files

    60 parts14
  • 2 layers46 × 84 mmVocore breakout, the printed circuit board in 3D

    Vocore breakout

    electroniceel/vocore2-breakout

    Breakout-board for the VoCore2

    88 parts11CC-BY-4.0
  • 4 layers105 × 38 mmPrintalyzer uvdensitometer, the printed circuit board in 3D

    Printalyzer uvdensitometer

    dektronics/printalyzer-uvdensitometer

    UV/VIS Reflection and Transmission Densitometer for Photographic Darkroom Use

    101 parts6
  • 2 layers98.8 × 97.4 mmNeOSensorV4 panel, the printed circuit board in 3D

    NeOSensorV4 panel

    fthiebolt/neOCampus-arduino

    neOCampus Arduino | home of the neOSensors end-devices

    278 parts5
  • 2 layers100 × 100 mmEvse, the printed circuit board in 3D

    Evse

    artashesamatuni/coreEVSE

    coreEVSE KiCad hardware project

    118 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP9808-E/MS?

Yes. The symbol is Sensors:MCP9808-E/MS and the footprint Package_SO:MSOP-8_3x3mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP9808-E/MS?

MSOP-8, with 8 pins. Its footprint is drawn on this page.

Where is the MCP9808-E/MS datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP9808-E/MS?

JLCPCB lists it as part C129490, with 531 in stock; the sellers' links on this page open their listings.

What can replace the MCP9808-E/MS?

Parts like it in the library: the DS18B20U by UMW, the LM75BDP(UMW) by UMW, the DS18B20U-15(MY) by Mysentech and the TMP175AIDGKR(UMW) by UMW. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP9808-E/MS?

27 boards in 23 repositories on GitHub; the most starred are listed on this page, with their KiCad files.