Skip to the content
123456789101112131415161718

MCP2515-I/SO

Microchip TechnologyExtended

-40℃~+85℃ 1Mbps 1uA 2.7V~5.5V 5mA CAN Controller SPI SOIC-18-300mil CAN Controllers ROHS

Part id
microchip/MCP2515-I/SO
Category
CAN Controllers
Package
SOIC-18-300mil
Pins
18
In stock
3,564 at JLCPCB (C153782)
Used on
15 open-source boards

Overview

The MCP2515-I/SO is a CAN Controller made by Microchip Technology in a SOIC-18-300mil package with 18 pins. -40℃~+85℃ 1Mbps 1uA 2.7V~5.5V 5mA CAN Controller SPI SOIC-18-300mil CAN Controllers ROHS.

PCBKit's library has its KiCad symbol (tinkerforge:MCP2515, from Tinkerforge) and its footprint (Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm, from KiCad's library), ready for a KiCad board. 3,564 are in stock at JLCPCB (part C153782). 15 open-source boards in 10 repositories on GitHub use it.

Symbol

17nRESET16nCS15SO14SI13SCK12INT4TX0RTS5TX1RTS6TX2RTS11RX0BF10RX1BF18VDD9VSS1TXCAN2RXCAN3CLKOUT8OSC17OSC2
tinkerforge:MCP2515From Tinkerforge

Footprint

123456789101112131415161718
Package_SO:SOIC-18W_7.5x11.6mm_P1.27mmFrom KiCad's library

From the datasheet

11
Supply, least
2.7 V · VDD, recommended operating min, Industrial (I) · p. 72
Supply, most
5.5 V · VDD, recommended operating max, Industrial (I) · p. 72
Supply, absolute maximum
7 V · VDD, absolute max · p. 71
Works from
-40 °C · Industrial (I), operating ambient min · p. 72
Works up to
85 °C · Industrial (I), operating ambient max · p. 72
Takes working
5 mA · Active supply current, typical · p. 1
Takes at most
10 mA · Operating current max, VDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO open · p. 72
Takes asleep
1 µA · Sleep mode standby current, typical · p. 1
Data rate, most
1 Mbit/s · CAN V2.0B data rate max · p. 1
Takes working
10 mA · VDD operating current max, 5.5 V, FOSC = 25 MHz, FCLK = 1 MHz, SO open · p. 72
Takes asleep
5 µA · Standby current max, Sleep mode, -40°C to +85°C · p. 72

What it is and has

7
CAN
CAN V2.0B, 1 Mb/s · p. 1
Acceptance filters
Six 29-bit filters · p. 1
Acceptance masks
Two 29-bit masks · p. 1
SPI
10 MHz · p. 1
SPI modes
0,0 and 1,1 · p. 1
CAN
V2.0B, 1 Mb/s · p. 1
Interface
SPI · p. 1

Specifications

72
ParameterConditionsAs printedPage
VDD VDDmax 7 V71
All inputs and outputs w.r.t. VSSmin -0.6 V71
Storage temperaturemin -65 · max 150 °C71
Ambient temperature with power appliedmin -65 · max 125 °C71
Soldering temperature of leads10 secondsmax 300 °C71
Supply Voltage VDDIndustrial (I)min 2.7 · max 5.5 V72
Register Retention Voltage VRETmin 2.4 V72
High-Level Input Voltage VIHRXCANmin 2 V72
Low-Level Input Voltage VILRXCAN, TXnRTS Pinsmin -0.3 V72
Low-Level Input Voltage VILSCK, CS, SImin -0.3 V72
Low-Level Output Voltage VOLTXCAN; IOL = +6.0 mA, VDD = 4.5Vmax 0.6 V72
Low-Level Output Voltage VOLRXnBF Pins; IOL = +8.5 mA, VDD = 4.5Vmax 0.6 V72
Low-Level Output Voltage VOLSO, CLKOUT; IOL = +2.1 mA, VDD = 4.5Vmax 0.6 V72
Low-Level Output Voltage VOLINT; IOL = +1.6 mA, VDD = 4.5Vmax 0.6 V72
Input Leakage Current ILIAll I/O except OSC1 and TXnRTS pins; CS = RESET = VDD, VIN = VSS to VDDmin -1 · max 1 uA72
Input Leakage Current ILIOSC1 Pinmin -5 · max 5 uA72
Internal Capacitance (All Inputs and Outputs) CINTTAMB = 25°C, fC = 1.0 MHz, VDD = 0V; periodically sampled and not 100% testedmax 7 pF72
Operating Current IDDVDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO = Openmax 10 mA72
Standby Current (Sleep mode) IDDSIndustrial (I); CS, TXnRTS = VDD, Inputs tied to VDD or VSS, -40°C TO +85°Cmax 5 uA72
Clock-In Frequency FOSC4.5V to 5.5Vmin 1 · max 40 MHz73
Clock-In Frequency FOSC2.7V to 5.5Vmin 1 · max 25 MHz73
Clock-In Period TOSC4.5V to 5.5Vmin 25 · max 1000 ns73
Clock-In Period TOSC2.7V to 5.5Vmin 40 · max 1000 ns73
Duty Cycle (External Clock Input) TDUTYTOSH/(TOSH + TOSL)min 0.45 · max 0.55 —73
Wake-up Noise Filter TWFmin 100 ns73
RESET Pin Low Time trlmin 2 us73
CLKOUT Pin High Time thCLKOUTTOSC = 40 ns (Note 1)min 15 ns74
CLKOUT Pin Low Time tlCLKOUTTOSC = 40 ns (Note 1)min 15 ns74
CLKOUT Pin Rise Time trCLKOUTMeasured from 0.3 VDD to 0.7 VDD (Note 1)max 5 ns74
CLKOUT Pin Fall Time tfCLKOUTMeasured from 0.7 VDD to 0.3 VDD (Note 1)max 5 ns74
CLOCKOUT Propagation Delay tdCLKOUTNote 1max 100 ns74
Clock Frequency FCLKmax 10 MHz75
CS Setup Time TCSSmin 50 ns75
CS Hold Time TCSHmin 50 ns75
CS Disable Time TCSDmin 50 ns75
Data Setup Time TSUmin 10 ns75
Data Hold Time THDmin 10 ns75
CLK Rise Time TRNote 1: This parameter is not 100% tested.max 2 us75
CLK Fall Time TFNote 1: This parameter is not 100% tested.max 2 us75
Clock High Time THImin 45 ns75
Clock Low Time TLOmin 45 ns75
Clock Delay Time TCLDmin 50 ns75
Clock Enable Time TCLEmin 50 ns75
Output Valid from Clock Low TVmax 45 ns75
Output Hold Time THOmin 0 ns75
Output Disable Time TDISmax 100 ns75
All inputs and outputs w.r.t. VSSUpper limit: VDD +1.0Vmin -0.6 V71
Ambient temperature with power appliedAbsolute maximum ratingmin -65 · max 125 °C71
Soldering temperature of leads (10 seconds)10 secondsmax 300 °C71
Supply Voltage VDDIndustrial (I): TAMB = -40°C to +85°Cmin 2.7 · max 5.5 V72
Register Retention Voltage VRETIndustrial (I)min 2.4 V72
High-Level Input Voltage VIHRXCAN; upper limit: VDD + 1min 2 V72
Low-Level Input Voltage VILRXCAN, TXnRTS Pins; upper limit: .15 VDDmin -0.3 V72
Low-Level Input Voltage VILSCK, CS, SI; upper limit: 0.4 VDDmin -0.3 V72
Internal Capacitance (All Inputs and Outputs) CINTTAMB = 25°C, fC = 1.0 MHz, VDD = 0V (Note 1)max 7 pF72
Wake-up Noise Filter TWFIndustrial (I)min 100 ns73
RESET Pin Low Time trlIndustrial (I)min 2 us73
Clock Frequency FCLKIndustrial (I)max 10 MHz75
CS Setup Time TCSSIndustrial (I)min 50 ns75
CS Hold Time TCSHIndustrial (I)min 50 ns75
CS Disable Time TCSDIndustrial (I)min 50 ns75
Data Setup Time TSUIndustrial (I)min 10 ns75
Data Hold Time THDIndustrial (I)min 10 ns75
CLK Rise Time TRNote 1max 2 us75
CLK Fall Time TFNote 1max 2 us75
Clock High Time THIIndustrial (I)min 45 ns75
Clock Low Time TLOIndustrial (I)min 45 ns75
Clock Delay Time TCLDIndustrial (I)min 50 ns75
Clock Enable Time TCLEIndustrial (I)min 50 ns75
Output Valid from Clock Low TVIndustrial (I)max 45 ns75
Output Hold Time THOIndustrial (I)min 0 ns75
Output Disable Time TDISIndustrial (I)max 100 ns75

Open-source boards using it

15See all 15
  • 6 layers235.1 × 213.7 mmQuiver PT3 Main PCB rounded, the printed circuit board in 3D

    Quiver PT3 Main PCB rounded

    Arrow-air/project-quiver

    Project Quiver documentation, designs, and project artifacts.

    164 parts617CERN-OHL-S-2.0
  • 2 layers144 × 59.5 mmSteeringmodule, the printed circuit board in 3D

    Steeringmodule

    ZeniteSolar/MDE22

    Esse módulo tem como objetivo controlar a direção da rabeta da embarcação Guarapuvu II, da equipe Zênite Solar do IFSC.

    88 parts2
  • 4 layers154 × 154 mmDC Controller STM32, the printed circuit board in 3D

    DC Controller STM32

    andymartell/Prius-STM32-DC-Motor-Contoller

    STM32 based DC Motor Controller using Prius Gen 3 hardware

    293 parts
  • 4 layers236.1 × 156.9 mmImpeller18, the printed circuit board in 3D

    Impeller18

    buglalis/degree

    764 parts
  • 2 layers130 × 115 mmObd2-simulator, the printed circuit board in 3D

    Obd2-simulator

    FilipRaic/obd2-simulator

    Open-source OBD-II simulator board: emulates a vehicle ECU per SAE J1979 and ISO 15031-5 over CAN. ESP32-S3 + MCP2515, 21 simulated parameters, DTC bank with MIL.

    107 partsMIT
  • 2 layers127.1 × 67.1 mmBlinCAN, the printed circuit board in 3D

    BlinCAN

    metalhead777/blinCAN

    A 24 channel LED driver with CAN bus interface and Arduino-style microcontroller.

    103 partsCC-BY-SA-4.0
  • 4 layers210.6 × 220 mmCMAIN PCB, the printed circuit board in 3D

    CMAIN PCB

    Arrow-air/project-caribou

    Project Caribou documentation, designs, and project artifacts.

    248 parts177CERN-OHL-S-2.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP2515-I/SO?

Yes. The symbol is tinkerforge:MCP2515 and the footprint Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP2515-I/SO?

SOIC-18-300mil, with 18 pins. Its footprint is drawn on this page.

Where is the MCP2515-I/SO datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP2515-I/SO?

JLCPCB lists it as part C153782, with 3,564 in stock; the sellers' links on this page open their listings.

What can replace the MCP2515-I/SO?

Parts like it in the library: the XL2515 by XINLUDA, the MCP2515T-E/SO-TUDI by Tudi, the MCP2515T-I/SO-HX by ZHHXDZ and the MCP2515T-I/SO-TUDI by Tudi. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP2515-I/SO?

15 boards in 10 repositories on GitHub; the most starred are listed on this page, with their KiCad files.