Skip to the content
12345678

ATA6561-GAQW

Microchip TechnologyExtended

-40℃~+150℃ 12uA 4.5V~5.5V 5Mbps 70mA CAN Transceiver SOIC-8 CAN Transceivers ROHS

Part id
microchip/ATA6561-GAQW
Category
CAN Transceivers
Package
SOIC-8
Pins
8
In stock
6,302 at JLCPCB (C2929602)
Used on
3 open-source boards

Overview

The ATA6561-GAQW is a CAN Transceiver made by Microchip Technology in a SOIC-8 package with 8 pins. -40℃~+150℃ 12uA 4.5V~5.5V 5Mbps 70mA CAN Transceiver SOIC-8 CAN Transceivers ROHS.

PCBKit's library has its KiCad symbol (Gekkio_Interface_CAN_LIN:ATA6561-GAQW, from Gekkio) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 6,302 are in stock at JLCPCB (part C2929602). 3 open-source boards in 3 repositories on GitHub use it.

Symbol

1TXD2GND3VCC4RXD5VIO6CANL7CANH8STBY
Gekkio_Interface_CAN_LIN:ATA6561-GAQWFrom Gekkio

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

8
Supply, least
4.5 V · VCC, recommended operating min · p. 10
Supply, most
5.5 V · VCC, recommended operating max · p. 10
Supply, least
2.8 V · VIO, recommended operating min · p. 10
Supply, absolute maximum
5.5 V · VCC, absolute max · p. 10
Junction, hottest
150 °C · Virtual junction temperature, absolute max · p. 10
Takes asleep
13 µA · sum of VCC and VIO max standby currents · p. 10
Junction to air (8-Lead SOIC)
145 K/W · Virtual junction to ambient, typical · p. 14
Data rate, most
5 Mbit/s · CAN communication speed max · p. 1

What it is and has

6
CAN FD
Ready · p. 1
Communication speed
up to 5 Mbps · p. 1
Wake-up
Remote wake-up via CAN bus · p. 1
Fault detection
RXD recessive clamping detection · p. 1
Protection
Undervoltage detection on VCC and VIO · p. 1
Internal pull-ups
TXD and STBY pulled up to VIO · p. 6

Around it

2
cap 100 nF
between VIO and GND; Shown in the ATA6561 typical application. · p. 9
cap 22 μF
between VCC and GND; Shown in the ATA6561 typical application; size depends on the external voltage regulator used. · p. 9

Specifications

67
ParameterConditionsAs printedPage
DC Voltage at CANH, CANL VCANH, VCANLmin -27 · max 42 V10
Transient Voltage at CANH, CANL VCANH, VCANLaccording to ISO 7637 part 2min -150 · max 100 V10
DC Voltage on all other pins VXmin -0.3 · max 5.5 V10
ESD according to IBEE CAN EMC - Test specification following IEC 61000-4-2Pin CANH, CANLmin -8 · max 8 kV10
ESDHBM following STM5.1 with 1.5 kΩ/100 pF; Pins CANH, CANL to GNDmin -6 · max 6 kV10
Component-Level ESDHBM according to ANSI/ESD STM5.1, JESD22-A114, AEC-Q100 (002)min -4 · max 4 kV10
CDM ESD STM 5.3.1min -750 · max 750 V10
ESD Machine Model AEC-Q100-RevF(003)min -200 · max 200 V10
Virtual Junction Temperature TvJmin -40 · max 150 °C10
Storage Temperature Range Tstgmin -55 · max 150 °C10
Supply Voltage VVCCSupply, Pin VCCmin 4.5 · max 5.5 V10
Supply Current in Normal Mode IVCC_recRecessive, VTXD = VVIOmin 2 · max 5 mA10
Supply Current in Normal Mode IVCC_domDominant, VTXD = 0Vmin 20 · typ 50 · max 70 mA10
Supply Current in Standby Mode IVCC_STBYVVCC = VVIO, VTXD = VNSIL = VVIOmax 12 uA10
Supply Current in Standby Mode IVCC_STBYTa = +25°C (Note 3)typ 7 uA10
Undervoltage Detection Threshold on Pin VCC Vuvd(VCC)min 2.75 · max 4.5 V10
Supply Voltage on Pin VIO VVIOATA6561min 2.8 · max 5.5 V10
Supply Current on Pin VIO IIO_recATA6561; Normal and Silent modes; Recessive, VTXD = VVIOmin 10 · typ 80 · max 250 uA10
Supply Current on Pin VIO IIO_rdomATA6561; Normal and Silent modes; Dominant, VTXD = 0Vmin 50 · typ 350 · max 500 uA10
Supply Current on Pin VIO IIO_STBYATA6561; Standby modemax 1 uA10
Undervoltage Detection Threshold on Pin VIO Vuvd(VIO)ATA6561min 1.3 · max 2.7 V10
Low-Level Input Voltage VILMode Control Input, Pin STBY; maximum 0.3 x VVIOmin -0.3 V11
Pull-Up Resistor to VIO RpuPin STBY; VSTBY = 0Vmin 75 · typ 125 · max 175 kΩ11
High-Level Leakage Current ILPin STBY; VSTBY = VVIOmin -2 · max 2 uA11
Low-Level Input Voltage VILCAN Transmit Data Input, Pin TXD; maximum 0.3 x VVIOmin -0.3 V11
Pull-Up Resistor to VIO RTXDPin TXD; VTXD = 0Vmin 20 · typ 35 · max 50 kΩ11
High-Level Leakage Current ITXDPin TXD; Normal mode, VTXD = VVIOmin -2 · max 2 uA11
Input Capacitance CTXDPin TXD; Note 3typ 5 · max 10 pF11
High-Level Output Current IOHPin RXD; Normal mode, VRXD = VVIO – 0.4V, VVIO = VVCCmin -8 · max -1 mA11
Low-Level Output Current IOLPin RXD; Normal mode, VRXD = 0.4V, bus dominantmin 2 · max 12 mA11
Dominant Output Voltage IIOVTXD = 0V, t < tto(dom)TXD, pin CANHmin 2.75 · typ 3.5 · max 4.5 V11
Dominant Output Voltage IIOVTXD = 0V, t < tto(dom)TXD, pin CANLmin 0.5 · typ 1.5 · max 2.25 V11
Bus Differential Output Voltage VO(diff)busVTXD = 0V, t < tto(dom)TXD, RL = 45Ω to 65Ωmin 1.5 · max 3 V11
Bus Differential Output Voltage VO(diff)busVVCC = 4.75V to 5.25V, VTXD = VVIO, receive, no loadmin -50 · max 50 mV11
Recessive Output Voltage VO(rec)Normal and Silent modes, VTXD = VVIO, no load; typical 0.5 x VVCCmin 2 · max 3 V11
Recessive Output Voltage VO(rec)Standby mode, VTXD = VVIO, no loadmin -0.1 · max 0.1 V11
Differential Receiver Threshold Voltage Vth(RX)difNormal and Silent modes (HSC), Vcm(CAN) = –27V to +27Vmin 0.5 · typ 0.7 · max 0.9 V12
Differential Receiver Threshold Voltage Vth(RX)difStandby mode (WUC), Vcm(CAN) = –27V to +27V (Note 1)min 0.4 · typ 0.7 · max 1 V12
Differential Receiver Hysteresis Voltage (HSC) Vhys(RX)difNormal and Silent modes (HSC), Vcm(CAN) = –27V to +27V (Note 1)min 50 · typ 120 · max 200 mV12
Dominant Output Current IIO(dom)VTXD = 0V, t < tto(dom)TXD, VVCC = 5V, pin CANH, VCANH = 0Vmin -100 · max -35 mA12
Dominant Output Current IIO(dom)VTXD = 0V, t < tto(dom)TXD, VVCC = 5V, pin CANL, VCANL = 5V/40Vmin 35 · max 100 mA12
Recessive Output Current IIO(rec)Normal and Silent modes, VTXD = VVIO, no load, VCANH = VCANL = –27V to +32Vmin -5 · max 5 mA12
Leakage Current IIO(rec)VVCC = VVIO = 0V, VCANH = VCANL = 5Vmin -5 · typ 0 · max 5 uA12
Input Resistance Rimin 9 · typ 15 · max 28 kΩ12
Input Resistance Deviation ∆RiBetween VCANH and VCANLmin -1 · typ 0 · max 1 %12
Differential Input Resistance Ri(dif)min 19 · typ 30 · max 56 kΩ12
Differential Input Resistance Ri(dif)TvJ < +125°Cmin 20 · typ 30 · max 56 kΩ12
Common-Mode Input Capacitance Ci(cm)Note 3max 20 pF12
Differential Input Capacitance Ci(dif)Note 3max 10 pF12
Delay Time from TXD to Bus Dominant td(TXD-busdom)Normal mode (Note 2)min 40 · max 130 ns12
Delay Time from TXD to Bus Recessive td(TXD-busrec)Normal mode (Note 2)min 40 · max 130 ns12
Delay Time from Bus Dominant to RXD td(busdom-RXD)Normal and Silent modes (Note 2)min 20 · max 100 ns12
Delay Time from Bus Recessive to RXD td(busrec-RXD)Normal and Silent modes (Note 2)min 20 · max 100 ns12
Propagation Delay from TXD to RXD tPD(TXD-RXD)Normal mode, Rising edge at pin TXDmin 40 · max 210 ns13
Propagation Delay from TXD to RXD tPD(TXD-RXD)Normal mode, Falling edge at pin TXDmin 40 · max 200 ns13
Propagation Delay from TXD to RXD tPD(TXD-RXD)Normal mode, Rising edge at pin TXD, RL = 120Ω, CL = 200 pF (Note 3)max 300 ns13
Propagation Delay from TXD to RXD tPD(TXD-RXD)Normal mode, Falling edge at pin TXD, RL = 120Ω, CL = 200pF (Note 3)max 300 ns13
TXD Dominant Time-Out Time tto(dom)TXDVTXD = 0V, Normal modemin 0.8 · max 3 ms13
Bus Wake-Up Time-Out Time tto_busStandby modemin 0.8 · max 3 ms13
Minimum Dominant/Recessive Bus Wake-Up Time twakeStandby modemin 0.75 · typ 3 · max 5 us13
Delay Time for Standby Mode to Normal Mode Transition tdel(stby-norm)Falling edge at pin STBY; NSIL = HIGHmax 47 us13
Delay Time for Normal Mode to Standby Mode Transition tdel(norm-stby)Rising edge at pin STBY; NSIL = HIGH (Note 3)max 5 us13
Debouncing Time for Recessive Clamping State Detection tRC_detV(CANH-CANL) > 900 mV; RXD = HIGH (Note 3)typ 90 ns13
Recessive Bit Time on Pin RXD tBit(RXD)Normal mode, tBit(TXD) = 500 ns (Note 3)min 400 · max 550 ns13
Recessive Bit Time on Pin RXD tBit(RXD)Normal mode, tBit(TXD) = 200 nsmin 120 · max 220 ns13
Thermal Resistance Virtual Junction to Ambient RthvJA8-Lead SOICtyp 145 K/W14
Thermal Shutdown of Bus Drivers TJsd8-Lead SOICmin 150 · typ 175 · max 195 °C14

Pins, by the datasheet

8
1 TXD
Transmit Data Input. · p. 8
2 GND
Ground Supply. · p. 8
3 VCC
Supply Voltage. · p. 8
4 RXD
Receive Data Output; reads out data from the bus lines. · p. 8
5 VIO
Supply Voltage for the I/O Level Adapter; the VIO and VCC lines are internally connected. · p. 8
6 CANL
Low-Level CAN Bus Line. · p. 8
7 CANH
High-Level CAN Bus Line. · p. 8
8 STBY
Standby Mode Control Input. · p. 8

Ordering codes, by the datasheet

1
ATA6561-GAQW
SOIC8 · AEC-Q100 qualified; standby mode; VIO pin for compatibility with 3.3V and 5V microcontrollers. · p. 2

Open-source boards using it

3
  • 2 layers84.7 × 75.8 mmEsp bluepill board, the printed circuit board in 3D

    Esp bluepill board

    ar216-2355/esp_bluepill_board

    できること - DCモーター 6台 駆動 - 電磁弁 4台 駆動 - ステッピングモーター 1台 駆動 - NeoPixel 1台(使えるか未確認) 駆動 - CAN通信可能 - PA10をHIGHにすることでUSB通信可能

    71 parts
  • 4 layers160 × 80 mmPIC18F ETH, the printed circuit board in 3D

    PIC18F ETH

    EBOThor/DTS_Board

    Digital to Synchro board

    281 partsMIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ATA6561-GAQW?

Yes. The symbol is Gekkio_Interface_CAN_LIN:ATA6561-GAQW and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ATA6561-GAQW?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the ATA6561-GAQW datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the ATA6561-GAQW?

JLCPCB lists it as part C2929602, with 6,302 in stock; the sellers' links on this page open their listings.

What can replace the ATA6561-GAQW?

Parts like it in the library: the TJA1051T/3/1J by NXP Semiconductors, the SN65HVD230D by Texas Instruments, the TJA1042T/1J by NXP Semiconductors and the CA-IF1051S by Chipanalog. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ATA6561-GAQW?

3 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.