Skip to the content

IST8310

iSentekExtended

-40℃~+85℃ 14bit 600uA I2C ±1.6mT ±2.5mT LGA-16(3x3) 3D Magnetic Sensors

Part id
isentek/IST8310
Category
3D Magnetic Sensors
Package
LGA-16(3x3)
Pins
16
In stock
3,582 at JLCPCB (C2683055)
Used on
16 open-source boards

Overview

The IST8310 is a 3D Magnetic Sensor made by iSentek in a LGA-16(3x3) package with 16 pins. -40℃~+85℃ 14bit 600uA I2C ±1.6mT ±2.5mT LGA-16(3x3) 3D Magnetic Sensors.

PCBKit's library has its KiCad symbol (Sensor_Magnetic:IST8310, from KiCad's library) and its footprint (Package_LGA:LGA-16_3x3mm_P0.5mm, from KiCad's library), ready for a KiCad board. 3,582 are in stock at JLCPCB (part C2683055). 16 open-source boards in 13 repositories on GitHub use it.

Symbol

1SCL2AVDD5CAD06CAD17VPP9VSS10C113DVDD14RST15DRDY16SDA
Sensor_Magnetic:IST8310From KiCad's library

Footprint

Package_LGA:LGA-16_3x3mm_P0.5mmFrom KiCad's library

From the datasheet

8
Supply, least
1.72 V · AVDD, recommended operating min · p. 10
Supply, most
3.6 V · AVDD, recommended operating max · p. 10
Supply, absolute maximum
3.6 V · AVDD, absolute max · p. 10
Works from
-40 °C · TA, recommended operating min · p. 10
Works up to
85 °C · TA, recommended operating max · p. 10
Takes working
1.2 mA · Full operation at 200 sps, typical · p. 10
Takes at most
1.2 mA · Full operation at highest stated rate, 200 sps, typical · p. 10
Takes asleep
10 µA · Standby current, typical · p. 10

What it is and has

11
Magnetic sensor
Single chip, 3-axis · p. 4
Package
3.0x3.0x1.0mm3, 16-pin LGA · p. 4
Interface
I2C slave, Fast Mode up to 400kHz · p. 4
Data output
14 bits · p. 4
Dynamic range
±1600uT (x, y-axis), ±2500uT (z-axis) · p. 4
Output data rate
Maximum 200Hz · p. 4
Hysteresis
<0.1%FS · p. 4
Sensitivity temperature drift
±0.016 %/ oK · p. 4
Offset temperature drift
0.024uT/ oK · p. 4
Temperature compensation
High precision · p. 4
Self-test
Built-in · p. 4

Around it

1
cap 0.1µF
between AVDD and GND; Ceramic, tied closely to the supply pin. · p. 10

Specifications

18
ParameterConditionsAs printedPage
Storage Temperature TSTGmin -40 · max 125 C10
Operating Temperature TAmin -40 · max 85 C10
Analog Supply Voltage AVDDmin -0.5 · max 3.6 V10
Digital Supply Voltage DVDDmin -0.5 · max 3.6 V10
Digital Input Voltage VINUpper limit: DVDD+0.3 Vmin -0.3 V10
Electrostatic Discharge Voltage VESD_HBMHuman Body Model (HBM)min -4000 · max 4000 V10
Electrostatic Discharge Voltage VESD_MMMachine Model (MM)min -350 · max 350 V10
Operating Temperature TAmin -40 · max 85 C10
Analog Supply Voltage AVDDmin 1.72 · typ 2.8 · max 3.6 V10
Digital Supply Voltage DVDDmin 1.72 · typ 1.8 · max 3.6 V10
Operating Current IDD3AFull operation, at 1 sps; TA=+25℃; AVDD=2.8V; DVDD=1.8Vtyp 20 uA10
Operating Current IDD3AFull operation, at 8 sps; TA=+25℃; AVDD=2.8V; DVDD=1.8Vtyp 72 uA10
Operating Current IDD3AFull operation, at 10 sps; TA=+25℃; AVDD=2.8V; DVDD=1.8Vtyp 80 uA10
Operating Current IDD3AFull operation, at 20 sps; TA=+25℃; AVDD=2.8V; DVDD=1.8Vtyp 140 uA10
Operating Current IDD3AFull operation, at 50 sps; TA=+25℃; AVDD=2.8V; DVDD=1.8Vtyp 320 uA10
Operating Current IDD3AFull operation, at 100 sps; TA=+25℃; AVDD=2.8V; DVDD=1.8Vtyp 600 uA10
Operating Current IDD3AFull operation, at 200 sps; TA=+25℃; AVDD=2.8V; DVDD=1.8Vtyp 1200 uA10
Standby Current ISTBTA=+25℃; AVDD=2.8V; DVDD=1.8Vtyp 10 uA10

Ordering codes, by the datasheet

1
IST8310
LGA – 16 pin · Tape and Reel: 5k pieces per reel · p. 21

Open-source boards using it

16See all 16
  • 4 layers66.3 × 40.2 mmCm4 drone, the printed circuit board in 3D

    Cm4 drone

    dridri/bcflight

    Raspberry Pi based drone flight controller and remote control

    56 parts175GPL-3.0
  • 6 layers39.5 × 39.5 mmLEVIA H7, the printed circuit board in 3D

    LEVIA H7

    piecol/LEVIA-H7

    Open hardware STM32H743 drone flight controller

    173 parts71CERN-OHL-S-2.0
  • 6 layers36 × 36 mmNewSkyH7-Air, the printed circuit board in 3D

    NewSkyH7-Air

    kuku-199/NewSky

    159 parts10Apache-2.0
  • 2 layers50 × 50 mmUpper board, the printed circuit board in 3D

    Upper board

    Peize-Liu/404APDdemo

    404 auto pilot drone demo

    125 parts9
  • 4 layers65 × 30 mmRbpi z hat, the printed circuit board in 3D

    Rbpi z hat

    chipiki/PXFmini_v2

    It's attempt to make a second version of died project PXFmini

    119 parts7
  • 6 layers22 × 42 mmLEVIA H7 M2, the printed circuit board in 3D

    LEVIA H7 M2

    piecol/LEVIA_H7_M2

    106 parts6CERN-OHL-S-2.0
  • 4 layers98.7 × 104 mmFlight Controller, the printed circuit board in 3D

    Flight Controller

    ThaoMinhHoang/350_Flight_controller

    ECTE350 storage room for Locus team

    233 parts3
  • 4 layers48.9 × 49.8 mmFC REV2, the printed circuit board in 3D

    FC REV2

    xXsenseiXx/KHATAF-F411

    Open-hardware 4-layer STM32F411 drone flight controller designed in KiCad for INAV and Betaflight.

    73 parts2

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the IST8310?

Yes. The symbol is Sensor_Magnetic:IST8310 and the footprint Package_LGA:LGA-16_3x3mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the IST8310?

LGA-16(3x3), with 16 pins. Its footprint is drawn on this page.

Where is the IST8310 datasheet?

iSentek publishes it: the Datasheet link on this page opens it.

Where can I order the IST8310?

JLCPCB lists it as part C2683055, with 3,582 in stock; the sellers' links on this page open their listings.

What can replace the IST8310?

Parts like it in the library: the IST8308 by iSentek. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the IST8310?

16 boards in 13 repositories on GitHub; the most starred are listed on this page, with their KiCad files.