IP5306_4.35V
INJOINICExtended
0℃~+70℃ 1 100uA 2.1A 4.35V 4.65V~5.5V Charging IC Lithium Battery 涓流充电、自动再充电、充电终止、欠压锁定、过放保护、Overcurrent Protection、Short-Circuit Protection、过压保护 SOP-8-EP Battery Management ROHS
- Part id
- injoinic/IP5306_4.35V
- Category
- Battery Management
- Package
- SOP-8-EP
- Pins
- 9
- In stock
- 1,783 at JLCPCB (C384572)
Overview
The IP5306_4.35V is a battery Management made by INJOINIC in a SOP-8-EP package with 9 pins. 0℃~+70℃ 1 100uA 2.1A 4.35V 4.65V~5.5V Charging IC Lithium Battery 涓流充电、自动再充电、充电终止、欠压锁定、过放保护、Overcurrent Protection、Short-Circuit Protection、过压保护 SOP-8-EP Battery Management ROHS.
PCBKit's library has its KiCad symbol (OLIMEX_Regulators:IP5306, from Olimex) and its footprint (OLIMEX_Regulators-FP:eSOP8L, from Olimex), ready for a KiCad board. 1,783 are in stock at JLCPCB (part C384572).
Symbol
Footprint
From the datasheet
15- Supply, least
- 4.65 V · VIN, recommended operating min · p. 4
- Supply, most
- 5.5 V · VIN, recommended operating max · p. 4
- Supply, least
- 3 V · BAT, boost battery operating min · p. 5
- Supply, most
- 4.4 V · BAT, boost battery operating max · p. 5
- Supply, absolute maximum
- 6 V · VIN, absolute max · p. 4
- Works from
- 0 °C · Ambient operating min · p. 4
- Works up to
- 70 °C · Ambient operating max · p. 4
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 4
- Takes working
- 3 mA · BAT, typical switching current at VBAT=3.7V, VOUT=5.0V, fs=500KHz · p. 5
- Takes asleep
- 100 µA · BAT, typical standby current at VIN=0V, VBAT=3.7V · p. 5
- Gives
- 2.4 A · Boost output rated max · p. 1
- Output
- 5 V · VOUT, typical boost output at VBAT=3.7V · p. 5
- Switches at
- 750 kHz · Typical charging switching frequency · p. 4
- Switches at
- 500 kHz · Typical boost switching frequency · p. 5
- Junction to air (ESOP8)
- 50 K/W · Junction to ambient, stated thermal resistance · p. 4
What it is and has
15- Synchronous boost and charging
- 2.4A boost, 2.1A charging · p. 1
- Boost efficiency
- Up to 92% · p. 1
- Charging efficiency
- Up to 91% · p. 1
- Power path management
- Supports simultaneous charging and discharging · p. 1
- Charging current adjustment
- Adaptive charging current and adapter adaptation · p. 1
- Battery indication
- 1, 2, 3 or 4 LEDs · p. 1
- Lighting
- Built-in lighting LED driver · p. 1
- Load detection
- Automatic phone insertion and removal detection · p. 1
- Automatic standby
- Recognizes load and automatically enters standby · p. 1
- Integrated power MOS
- Single inductor for charging and discharging · p. 1
- Output protection
- Overcurrent, overvoltage and short circuit · p. 1
- Input and battery protection
- Input overvoltage, overcharge, overdischarge and discharge overcurrent · p. 1
- Thermal protection
- System overtemperature protection · p. 1
- Package
- ESOP8 · p. 1
- Battery cell type
- 4.35V · p. 3
Specifications
35| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| 端口输入电压范围 VIN | min -0.3 · max 6 V | 4 | |
| 结温范围 TJ | min -40 · max 150 ℃ | 4 | |
| 存储温度范围 Tstg | min -60 · max 150 ℃ | 4 | |
| 热阻(结温到环境) θJA | ESOP8; single stated value | typ 50 ℃/W | 4 |
| 人体模型(HBM) ESD | Single stated rating | max 4 KV | 4 |
| 输入电压 VIN | min 4.65 · typ 5 · max 5.5 V | 4 | |
| 负载电流 I | min 0 · typ 2.4 A | 4 | |
| 工作环境温度 TA | min 0 · max 70 ℃ | 4 | |
| 输入电压 VIN | 充电系统; TA=25℃,L=1.0uH | min 4.65 · typ 5 · max 5.5 V | 4 |
| 充电电流 ICHRG | VIN 输入端电流; TA=25℃,L=1.0uH | typ 1.8 A | 4 |
| 充电开关频率 fs | TA=25℃,L=1.0uH | typ 750 KHz | 4 |
| 涓流充电电流 ITRKL | VIN=5V,BAT=2.7V; TA=25℃,L=1.0uH | typ 100 mA | 4 |
| 涓流截止电压 VTRKL | TA=25℃,L=1.0uH | typ 2.9 V | 4 |
| 充电截止时间 TEND | TA=25℃,L=1.0uH | typ 24 Hour | 4 |
| 输入欠压保护 VUVLO | 上升电压; TA=25℃,L=1.0uH | typ 4.5 V | 4 |
| 欠压保护迟滞 VUVLOH | TA=25℃,L=1.0uH | typ 200 mV | 5 |
| 电池工作电压 VBAT | 升压系统; TA=25℃,L=1.0uH | min 3 · max 4.4 V | 5 |
| 开关工作电池输入电流 IBAT | VBAT=3.7V,VOUT=5.0V,fs=500KHz; TA=25℃,L=1.0uH | typ 3 mA | 5 |
| 开关工作电池输入电流 IBAT | VIN=5V,Device not switching; TA=25℃,L=1.0uH | typ 100 uA | 5 |
| DC 输出电压 VOUT | VBAT=3.7V; TA=25℃,L=1.0uH | typ 5 V | 5 |
| 输出电压纹波 ΔVOUT | VBAT=3.7V,VOUT=5.0V,fs=500KHz; TA=25℃,L=1.0uH | typ 100 mV | 5 |
| 升压开关频率 fs | TA=25℃,L=1.0uH | typ 500 KHz | 5 |
| 升压系统供电电流 Ivout | TA=25℃,L=1.0uH | typ 2.4 A | 5 |
| 负载过流检测时间 TUVD | 输出电压持续低于 4.4V; TA=25℃,L=1.0uH | typ 50 ms | 5 |
| 负载短路检测时间 TOCD | 输出电流持续大于 4A; TA=25℃,L=1.0uH | min 150 · max 200 us | 5 |
| PMOS 导通电阻 rDSON | 控制系统; TA=25℃,L=1.0uH | typ 35 mΩ | 5 |
| NMOS 导通电阻 rDSON | 控制系统; TA=25℃,L=1.0uH | typ 30 mΩ | 5 |
| 电池输入待机电流 ISTB | VIN=0V,VBAT=3.7V; TA=25℃,L=1.0uH | typ 100 uA | 5 |
| LED 照明驱动电流 Key | TA=25℃,L=1.0uH | typ 25 mA | 5 |
| LED 显示驱动电流 IL1, IL2, IL3 | TA=25℃,L=1.0uH | typ 10 mA | 5 |
| 负载自动检测时间 TloadD | 负载电流持续小于 45mA; TA=25℃,L=1.0uH | typ 32 s | 5 |
| 短按键唤醒时间 TOnDebounce | TA=25℃,L=1.0uH | typ 50 ms | 5 |
| 打开 light 时间 TKeylight | TA=25℃,L=1.0uH | typ 2 s | 5 |
| 热关断温度 TOTP | 上升温度; TA=25℃,L=1.0uH | typ 125 ℃ | 5 |
| 热关断温度迟滞 ΔTOTP | TA=25℃,L=1.0uH | typ 40 ℃ | 5 |
Pins, by the datasheet
9- 1 VIN
- DC5V 充电输入引脚 · p. 2
- 2 LED1
- LED 驱动引脚 · p. 2
- 3 LED2
- LED 驱动引脚 · p. 2
- 4 LED3
- LED 驱动引脚 · p. 2
- 5 KEY
- 按键输入,照明灯驱动复用;不需要按键时悬空。 · p. 8
- 6 BAT
- 升压输入引脚,连接锂电池正极。 · p. 2
- 7 SW
- DC-DC 开关引脚 · p. 2
- 8 VOUT
- 5V 升压输出引脚 · p. 2
- PowerPAD PowerPAD
- Connect to GND · p. 2
Ordering codes, by the datasheet
4- IP5306
- eSOP8 · 4.20V cell · p. 3
- IP5306_4.30V
- eSOP8 · 4.30V cell · p. 3
- IP5306_4.35V
- eSOP8 · 4.35V cell · p. 3
- IP5306_4.40V
- eSOP8 · 4.40V cell · p. 3
Parts like it
3IP5306
ESOP-80℃~+70℃ 1 100uA 2.1A 3V 4.2V 4.65V~5.5V Charging IC、Protection IC I2C Lithium Battery ESOP-8 Battery Management ROHSINJOINICBattery ManagementIP5306-I2C
ESOP-80℃~+70℃ 100uA 2.1A 4.2V 4.75V~5.5V Charging IC I2C Lithium Battery 恒流充电、恒压充电、涓流充电、自动再充电、充电终止、可编程充电电流、过放保护、Overcurrent Protection、Short-Circuit Protection、过压保护 ESOP-8 Battery Management ROHSINJOINICBattery ManagementIP5306-LC
ESOP-80℃~+70℃ 100uA 2.1A 4.2V 4.75V~5.5V Charging IC I2C Lithium Battery Not supported 恒流充电、涓流充电、自动再充电、充电终止、欠压锁定、过放保护、Overcurrent Protection、Short-Circuit Protection、过压保护 ESOP-8 Battery Management ROHSINJOINICBattery Management
Questions
Is there a KiCad symbol and footprint for the IP5306_4.35V?
Yes. The symbol is OLIMEX_Regulators:IP5306 and the footprint OLIMEX_Regulators-FP:eSOP8L, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the IP5306_4.35V?
SOP-8-EP, with 9 pins. Its footprint is drawn on this page.
Where is the IP5306_4.35V datasheet?
INJOINIC publishes it: the Datasheet link on this page opens it.
Where can I order the IP5306_4.35V?
JLCPCB lists it as part C384572, with 1,783 in stock; the sellers' links on this page open their listings.
What can replace the IP5306_4.35V?
Parts like it in the library: the IP5306 by INJOINIC, the IP5306-I2C by INJOINIC and the IP5306-LC by INJOINIC. Check their datasheets: a part that fits the footprint may still differ in its ratings.