Skip to the content
12345

AP2205-W5

Diodes IncorporatedExtended

-40℃~+125℃@(Tj) 1 200mA 24V 30uVrms 500mV@(150mA) 500uA 60dB@(1kHz) Adjustable Over Current Protection、Thermal shutdown、Enable control、Reverse-polarity current protection Positive SOT-25 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
diodes/AP2205-W5
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
SOT-25
Pins
5
In stock
4,915 at JLCPCB (C3001658)
Used on
11 open-source boards

Overview

The AP2205-W5 is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Diodes Incorporated in a SOT-25 package with 5 pins. -40℃~+125℃@(Tj) 1 200mA 24V 30uVrms 500mV@(150mA) 500uA 60dB@(1kHz) Adjustable Over Current Protection、Thermal shutdown、Enable control、Reverse-polarity current protection Positive SOT-25 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:AP2205-W5-7_C3001658, from EasyEDA) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 4,915 are in stock at JLCPCB (part C3001658). 11 open-source boards in 8 repositories on GitHub use it.

Symbol

5VOUT4ADJ/NC3EN2GND1VIN
EasyEDA_Cloud:AP2205-W5-7_C3001658From EasyEDA

Footprint

12345
Package_TO_SOT_SMD:SOT-23-5From KiCad's library

From the datasheet

14
Supply, least
2.3 V · VIN, recommended operating min · p. 4
Supply, most
24 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
36 V · VIN, absolute max · p. 4
Junction, hottest
150 °C · Operating junction temperature, absolute max · p. 4
Takes working
36 µA · Ground current, typical at IOUT = 100uA · p. 5
Takes asleep
10 nA · Standby current, typical with VEN in OFF Mode · p. 5
Gives
150 mA · Output current max, VOUT ≦ 1.8V · p. 4
Gives
200 mA · Output current max, VOUT > 1.8V · p. 4
Dropout
100 mV · Dropout typical at IOUT = 100uA, VOUT ≥ 2.3V · p. 5
Dropout
270 mV · Dropout typical at IOUT = 50mA, VOUT ≥ 2.3V · p. 5
Dropout
320 mV · Dropout typical at IOUT = 100mA, VOUT ≥ 2.3V · p. 5
Dropout
360 mV · Dropout typical at IOUT = 150mA, VOUT ≥ 2.3V · p. 5
Junction to air (SOT25)
160 K/W · Junction to ambient, 2-layer FR-4 with 1.5cm*1.5cm thermal sink pad · p. 4
Junction to case (SOT25)
29 K/W · Junction to case · p. 4

What it is and has

6
Input voltage range
2.3V to 24V · p. 1
Output voltage range
1.24V to 22V · p. 1
Ripple rejection
60dB @ f = 1kHz · p. 1
Capacitor compatibility
Low ESR ceramic capacitor · p. 1
Protection
Thermal shutdown · p. 1
Compliance
Lead-free and RoHS compliant · p. 1

Specifications

36
ParameterConditionsAs printedPage
Supply Input Voltage VINmax 36 V4
Enable Input Voltage VCEmax 36 V4
Output Current IOUTmax 250 mA4
Lead Temperature (Soldering, 10sec) TLEADSoldering, 10secmax 260 °C4
Operating Junction Temperature TJmax 150 °C4
Thermal Resistance (Note 6) JASOT25; mounted on a 2-Layer FR-4 PCB board with 1.5cm*1.5cm thermal sink pad in free airmax 160 °C/W4
Thermal Resistance JCSOT25max 29 °C/W4
Storage Temperature Range TSTGmin -65 · max 150 °C4
ESD (Charge Device Model) —max 1000 V4
ESD (Human Body Model) —max 2000 V4
Supply Input Voltage VINmin 2.3 · max 24 V4
Operating Junction Temperature TJmin -40 · max 125 °C4
Output Current IOUTVOUT ≦ 1.8Vmax 150 mA4
Output Current IOUTVOUT > 1.8Vmax 200 mA4
Reference Voltage VREFVIN = VOUT+1V, TJ = +25°C, IOUT = 100uA, CIN = 1.0uF, COUT = 2.2uFmin 1.215 · typ 1.24 · max 1.265 V5
Input Voltage VINmin 2.3 · max 24 V5
Maximum Output Current IOUT(MAX)VIN-VOUT = 1V, VOUT = 98%  VOUTmin 200 · typ 250 mA5
Line Regulation VOUT/VINVOUT + 1V ≤ VIN ≤ 24Vtyp 0.05 %5
Load Regulation VOUT/VOUT1mA ≤ IOUT ≤ 200mAtyp 0.5 %5
Dropout Voltage (Note 7) VDROPIOUT = 100uA; valid when VOUT ≥ 2.3Vtyp 100 · max 150 mV5
Dropout Voltage (Note 7) VDROPIOUT = 50mA; valid when VOUT ≥ 2.3Vtyp 270 · max 350 mV5
Dropout Voltage (Note 7) VDROPIOUT = 100mA; valid when VOUT ≥ 2.3Vtyp 320 · max 460 mV5
Dropout Voltage (Note 7) VDROPIOUT = 150mA; valid when VOUT ≥ 2.3Vtyp 360 · max 500 mV5
Ground Current IGNDIOUT = 100uAtyp 36 uA5
Ground Current IGNDIOUT = 50mAtyp 0.5 mA5
Ground Current IGNDIOUT = 100mAtyp 1.3 mA5
Ground Current IGNDIOUT = 150mAtyp 2.5 mA5
Standby Current ISTDVIN = VOUT+1V; VEN in OFF Modetyp 0.01 · max 1 uA5
Power Supply Rejection Ration PSRRRipple 0.5VP-P; VIN = VOUT+1V; f = 100Hztyp 60 dB5
Power Supply Rejection Ration PSRRRipple 0.5VP-P; VIN = VOUT+1V; f = 1kHztyp 60 dB5
Output Voltage Temperature Coefficient ∆VOUT/(VOUT∆T)IOUT = 100uA; -40°C ≤ TJ ≤ +125°C; typical stated as ±100typ 100 ppm/°C5
RMS Output Noise VNOITJ = +25°C, 10Hz ≤ f ≤ 100kHztyp 30 uVRMS5
ADJ Pin Current IADJIOUT = 100uAtyp 0.5 uA5
EN Pin Current IENVEN = VOUT + 1Vtyp 3 uA5
EN “High” Voltage —EN Input Voltage “High”min 2 V5
EN “Low” Voltage —EN Input Voltage “Low”max 0.4 V5

Pins, by the datasheet

5
1 VIN
Supply input. · p. 1
2 GND
Ground. · p. 1
3 EN
Enable input. · p. 1
4 ADJ/NC
Adjustment or no connection, depending on version. · p. 1
5 VOUT
Regulated output. · p. 1

Open-source boards using it

11See all 11
  • 4 layers36 × 50.2 mmRacer, the printed circuit board in 3D

    Racer

    StuckAtPrototype/Racer

    These are structured into their own files. I could have used submodules, but decided against it.

    83 parts3.8kApache-2.0
  • 2 layers45 × 45 mmAirCube, the printed circuit board in 3D

    AirCube

    StuckAtPrototype/AirCube

    Works standalone out of the box. Pairs with Home Assistant in minutes. Other platforms are supported through community-contributed extensions.

    61 parts379Apache-2.0
  • 4 layers74.7 × 30 mmController, the printed circuit board in 3D

    Controller

    StuckAtPrototype/Thumbtroller

    77 parts305
  • 2 layers48 × 72 mmFlipklok, the printed circuit board in 3D

    Flipklok

    h-buter/Flipklok

    Welcome to the repository for my project as part of my Bachelor's degree in Electronics at Windesheim. This project involves creating a flip clock inspired by the design from the 1970s, which is synchronized using time…

    70 parts
  • 2 layers108 × 70 mmGlowpad, the printed circuit board in 3D

    Glowpad

    mjvarga/Interactive-Glowpad-PCB-Design

    A 5-pad capacitive touch board built around the ESP32-S3, featuring addressable RGB LEDs and piezo audio feedback.

    42 parts
  • 2 layers45 × 45 mmAirCube, the printed circuit board in 3D

    AirCube

    StuckAtPrototype/AirCube

    Works standalone out of the box. Pairs with Home Assistant in minutes. Other platforms are supported through community-contributed extensions.

    52 parts379Apache-2.0
  • 2 layers90 × 71 mmTd hv, the printed circuit board in 3D

    Td hv

    tdaede/td-crt

    tubes

    64 parts373
  • 2 layers70 × 79 mmIntegrated circuits, the printed circuit board in 3D

    Integrated circuits

    LilyTronics/lily_kicad_lib

    KiCad library by LilyTronics

    37 parts2MIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the AP2205-W5?

Yes. The symbol is EasyEDA_Cloud:AP2205-W5-7_C3001658 and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AP2205-W5?

SOT-25, with 5 pins. Its footprint is drawn on this page.

Where is the AP2205-W5 datasheet?

Diodes Incorporated publishes it: the Datasheet link on this page opens it.

Where can I order the AP2205-W5?

JLCPCB lists it as part C3001658, with 4,915 in stock; the sellers' links on this page open their listings.

What can replace the AP2205-W5?

Parts like it in the library: the SPX3819M5-L-5-0 by TECH PUBLIC, the BL8075CB5TR50 by BL, the DS8241-50S5 by DSTECH and the AP2204K-5.0TRG1(MS) by MSKSEMI. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AP2205-W5?

11 boards in 8 repositories on GitHub; the most starred are listed on this page, with their KiCad files.