Skip to the content
12345678910111213141516

RA-01

Ai-ThinkerExtended

Part id
ai-thinker/RA-01
Category
LoRa Modules
Package
SMD-16P
Pins
16
In stock
2,933 at JLCPCB (C90040)
Used on
12 open-source boards

Overview

The RA-01 is a loRa Module made by Ai-Thinker in a SMD-16P package with 16 pins.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:RA-01, from EasyEDA) and its footprint (EasyEDA_Cloud:WIRELM-SMD_RA-01, from EasyEDA), ready for a KiCad board. 2,933 are in stock at JLCPCB (part C90040). 12 open-source boards in 8 repositories on GitHub use it.

Symbol

1ANT2GND33.3V4RESET5DIO06DIO17DIO28DIO39GND10DIO411DIO512SCK13MISO14MOSI15NSS16GND
EasyEDA_Cloud:RA-01From EasyEDA

Footprint

12345678910111213141516
EasyEDA_Cloud:WIRELM-SMD_RA-01From EasyEDA

From the datasheet

8
Supply, least
1.8 V · VDD, recommended operating min · p. 2
Supply, most
3.6 V · VDD, recommended operating max · p. 2
Works from
-40 °C · Operating temperature min, recommended environment · p. 2
Works up to
85 °C · Operating temperature max, recommended environment · p. 2
Takes working
12.15 mA · Receive average current, 433 MHz · p. 1
Takes at most
97 mA · Transmit average current, 470 MHz; largest stated · p. 1
Takes asleep
1.6 mA · Standby average current, 433 MHz · p. 1
Takes asleep
1.5 mA · Standby average current, 470 MHz · p. 1

What it is and has

9
Modulation
FSK, GFSK, MSK, GMSK, LoRa™, OOK · p. 1
Sensitivity
Down to -148 dBm · p. 1
SPI
Half-duplex · p. 1
Packet engine
Up to 256 bytes, CRC · p. 1
RSSI dynamic range
127 dB · p. 1
RF functions
Automatic RF signal detection, CAD mode, ultrafast AFC · p. 1
Shield
Shielding enclosure · p. 1
Antenna
Spring antenna · p. 1
Package
SMD-16 · p. 1

Specifications

17
ParameterConditionsAs printedPage
频率范围min 410 · max 525 MHz1
工作电压min 2.5 · typ 3.3 · max 3.7 V1
平均工作电流433MHz Tx; averagetyp 93 mA1
平均工作电流433MHz Rx; averagetyp 12.15 mA1
平均工作电流433MHz Stanbdby; averagetyp 1.6 mA1
平均工作电流470MHz Tx; averagetyp 97 mA1
平均工作电流470MHz Rx; averagetyp 12.15 mA1
平均工作电流470MHz Stanbdby; averagetyp 1.5 mA1
工作温度min -30 · max 85 °C1
存储环境<90%RHmin -40 · max 90 °C1
供电电压 VDDmin 1.8 · typ 3.3 · max 3.6 V2
工作温度 TOPRmin -40 · typ 20 · max 85 ℃2
IO电平 VIOmin 1.8 · typ 3.3 · max 3.6 V2
数字输入低电平 VILmax 0.2 V2
数字输入高电平 VIHmin 0.8 V2
数字输出低电平 VoLmax 0.1 V2
数字输出高电平 VoHmin 0.9 V2

Pins, by the datasheet

16
1 ANT
Antenna connection. · p. 2
2 GND
Ground. · p. 2
3 3.3V
3.3 V supply. · p. 2
4 RESET
Reset. · p. 2
5 DIO0
Software-configurable digital IO0. · p. 3
6 DIO1
Software-configurable digital IO1. · p. 3
7 DIO2
Software-configurable digital IO2. · p. 3
8 DIO3
Software-configurable digital IO3. · p. 3
9 GND
Ground. · p. 3
10 DIO4
Configurable digital IO4. · p. 3
11 DIO5
Software-configurable digital IO5. · p. 3
12 SCK
SPI clock input. · p. 3
13 MISO
SPI data output. · p. 3
14 MOSI
SPI data input. · p. 3
15 NSS
SPI chip-select input. · p. 3
16 GND
Ground. · p. 3

Open-source boards using it

12See all 12
  • 2 layers40 × 95.3 mmLora tracker, the printed circuit board in 3D

    Lora tracker

    sh123/esp32_loradv

    ESP32 based Codec2/OPUS DV hobby UHF 3d printed handheld transceiver aka walkie-talkie

    34 parts127GPL-2.0
  • 4 layers36.6 × 60.3 mmStratoSoar MK3.0, the printed circuit board in 3D

    StratoSoar MK3.0

    crnicholson/StratoSoar-MK3

    StratoSoar MK3, an autonomous glider meant for high-altitudes, accessible to everyone

    85 parts43
  • 2 layers94.8 × 67.2 mmArgo v9-stable rev4, the printed circuit board in 3D

    Argo v9-stable rev4

    SensorsINI/argo

    Code for Autonomous sail boat

    139 parts16
  • 2 layers75 × 87 mmNode, the printed circuit board in 3D

    Node

    stustanet/waschfreiheit

    Online status monitoring for washing machines

    103 parts5
  • 2 layers35.5 × 126 mmPlantMonitor, the printed circuit board in 3D

    PlantMonitor

    crnicholson/Plant-Monitor

    Plant Monitor is a way to view data from a remote humidity sensor on web interface, which then tells you when you need to water your plants plus the air humidity, soil humidity, air temp, and air pressure.

    50 parts2
  • 2 layers376.1 × 352.9 mmModule radio, the printed circuit board in 3D

    Module radio

    victorstoica114/ESP32-C3_Radio

    PlatformIO project for testing multiple radio modules with an ESP32-C3 board, an optional SSD1306 OLED display, and serial/AT-command based firmware variants.

    175 parts1MIT
  • 2 layers81.8 × 56.6 mmNode, the printed circuit board in 3D

    Node

    stustanet/waschfreiheit

    Online status monitoring for washing machines

    28 parts5
  • 2 layers31.2 × 52.3 mmGroundMonitor, the printed circuit board in 3D

    GroundMonitor

    crnicholson/Plant-Monitor

    Plant Monitor is a way to view data from a remote humidity sensor on web interface, which then tells you when you need to water your plants plus the air humidity, soil humidity, air temp, and air pressure.

    26 parts2

Questions

Is there a KiCad symbol and footprint for the RA-01?

Yes. The symbol is EasyEDA_Cloud:RA-01 and the footprint EasyEDA_Cloud:WIRELM-SMD_RA-01, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the RA-01?

SMD-16P, with 16 pins. Its footprint is drawn on this page.

Where is the RA-01 datasheet?

Ai-Thinker publishes it: the Datasheet link on this page opens it.

Where can I order the RA-01?

JLCPCB lists it as part C90040, with 2,933 in stock; the sellers' links on this page open their listings.

Which open-source boards use the RA-01?

12 boards in 8 repositories on GitHub; the most starred are listed on this page, with their KiCad files.