Skip to the content
12345

ADP7118AUJZ-3.3-R7

Analog DevicesExtended

-40℃~+125℃ 1 11uVrms 140uA 200mA 200mV@(200mA) 20V 3.3V 88dB@(10kHz) Fixed Over Current Protection、Soft Start、Enable、Thermal Shutdown Positive TSOT-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
adi/ADP7118AUJZ-3.3-R7
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
TSOT-5
Pins
5
In stock
3,177 at JLCPCB (C194022)
Used on
5 open-source boards

Overview

The ADP7118AUJZ-3.3-R7 is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Analog Devices in a TSOT-5 package with 5 pins. -40℃~+125℃ 1 11uVrms 140uA 200mA 200mV@(200mA) 20V 3.3V 88dB@(10kHz) Fixed Over Current Protection、Soft Start、Enable、Thermal Shutdown Positive TSOT-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:ADPL44002AUJZ-1.8-R7, from EasyEDA) and its footprint (Package_TO_SOT_SMD:TSOT-23-5, from KiCad's library), ready for a KiCad board. 3,177 are in stock at JLCPCB (part C194022). 5 open-source boards in 5 repositories on GitHub use it.

Symbol

5VOUT4SENSE/ADJ3EN1VIN2GND
EasyEDA_Cloud:ADPL44002AUJZ-1.8-R7From EasyEDA

Footprint

12345
Package_TO_SOT_SMD:TSOT-23-5From KiCad's library

From the datasheet

16
Supply, least
2.7 V · VIN, recommended operating min · p. 3
Supply, most
20 V · VIN, recommended operating max · p. 3
Supply, absolute maximum
24 V · VIN, absolute max · p. 5
Works from
-40 °C · Operating ambient min · p. 5
Works up to
125 °C · Operating ambient max · p. 5
Junction, hottest
150 °C · Junction temperature absolute max · p. 5
Takes working
50 µA · IGND typical, output enabled, no load · p. 3
Takes asleep
1.8 µA · IGND-SD typical, EN = GND · p. 3
Takes asleep
3 µA · IGND-SD typical, EN = GND, VIN = 20 V · p. 3
Gives
200 mA · Continuous output current max · p. 1
Current limit
360 mA · ILIMIT typical · p. 3
Output
3.3 V · Fixed 3.3 V option, nominal · p. 1
Dropout
30 mV · Typical at IOUT = 10 mA, table default VOUT = 5 V · p. 3
Dropout
200 mV · Typical at IOUT = 200 mA, table default VOUT = 5 V · p. 3
Junction to air (5引脚 TSOT)
170 K/W · Junction to ambient, four-layer board · p. 5
Junction to board (5引脚 TSOT)
43 K/W · ΨJB typical · p. 17

What it is and has

5
Output noise
11 μV rms · p. 1
Initial accuracy
±0.8% · p. 1
Enable
Precision enable · p. 1
Package options
2 mm × 2 mm 6-pin LFCSP, 8-pin SOIC, 5-pin TSOT · p. 1
Protection
Current limit and thermal overload protection · p. 17

Around it

1
cap 2.2 μF
between VOUT and GND; Ceramic output capacitor for stability · p. 1

Specifications

44
ParameterConditionsAs printedPage
输入电压范围 VINmin 2.7 · max 20 V3
工作电源电流 IGNDIOUT = 0 uAtyp 50 · max 140 uA3
工作电源电流 IGNDIOUT = 10 mAtyp 80 · max 190 uA3
工作电源电流 IGNDIOUT = 200 mAtyp 180 · max 320 uA3
关断电流 IGND-SDEN = GNDtyp 1.8 uA3
关断电流 IGND-SDEN = GND,VIN = 20 Vtyp 3 uA3
关断电流 IGND-SDEN = GNDmax 10 uA3
输出电压精度 VOUTIOUT = 10 mA,TJ = 25°Cmin -0.8 · max 0.8 %3
输出电压精度 VOUT100 uA < IOUT < 200 mA,VIN = (VOUT + 1 V)至20 V,TJ = −40°C至+85°Cmin -1.2 · max 1.5 %3
输出电压精度 VOUT100 uA < IOUT < 200 mA,VIN = (VOUT + 1 V)至20 V;TJ = −40°C至+125°Cmin -1.8 · max 1.8 %3
电压调整率 ∆VOUT/∆VINVIN= (VOUT+ 1 V)至20 Vmin -0.015 · max 0.015 %/V3
负载调整率1 ∆VOUT/∆IOUTIOUT = 100 uA至200 mAtyp 0.002 · max 0.004 %/mA3
SENSE输入偏置电流 SENSEI-BIAS100 uA < IOUT < 200 mA,VIN = (VOUT + 1 V)至20 Vtyp 10 · max 1000 nA3
压差2 VDROPOUTIOUT = 10 mA;VOUT = 5 Vtyp 30 · max 60 mV3
压差2 VDROPOUTIOUT = 200 mA;VOUT = 5 Vtyp 200 · max 420 mV3
启动时间3 tSTART-UPVOUT = 5 Vtyp 380 us3
限流阈值4 ILIMIT输出电压降至额定典型值90%min 250 · typ 360 · max 460 mA3
热关断阈值 TSSDTJ上升typ 150 °C3
热关断迟滞 TSSD-HYStyp 15 °C3
输入电压上升 UVLORISEmax 2.69 V3
输入电压下降 UVLOFALLmin 2.2 V3
迟滞 UVLOHYStyp 230 mV3
逻辑高电平 ENHIGH2.7 V ≤ VIN ≤ 20 Vmin 1.15 · typ 1.22 · max 1.3 V3
逻辑低电平 ENLOW2.7 V ≤ VIN ≤ 20 Vmin 1.06 · typ 1.12 · max 1.18 V3
逻辑迟滞 ENHYS2.7 V ≤ VIN ≤ 20 Vtyp 100 mV3
漏电流 IEN-LKGEN = VIN或GND;2.7 V ≤ VIN ≤ 20 Vtyp 0.04 · max 1 uA3
延迟时间 tEN-DLYEN从0 V上升到VIN为0.1 × VOUT;2.7 V ≤ VIN ≤ 20 Vtyp 80 us3
输出噪声 OUTNOISE10 Hz至100 kHz,所有输出电压选项typ 11 uV rms3
电源抑制比 PSRR1 MHz,VIN = 7 V,VOUT = 5 Vtyp 50 dB3
电源抑制比 PSRR100 kHz,VIN = 7 V,VOUT = 5 Vtyp 68 dB3
电源抑制比 PSRR10 kHz,VIN = 7 V,VOUT = 5 Vtyp 88 dB3
VIN至GNDmin -0.3 · max 24 V5
VOUT至GND上限为VINmin -0.3 V5
EN至GNDmin -0.3 · max 24 V5
SENSE/ADJ至GNDmin -0.3 · max 6 V5
存储温度范围min -65 · max 150 °C5
结温(TJ) TJmax 150 °C5
工作环境温度(TA)范围 TAmin -40 · max 125 °C5
θJA θJA5引脚 TSOT;4层、4英寸× 3英寸电路板typ 170 °C/W5
ΨJB ΨJB5引脚 TSOT;4层板typ 43 °C/W5
θJA θJATSOT;覆铜面积50 mm²typ 152 °C/W17
θJA θJATSOT;覆铜面积100 mm²typ 146 °C/W17
θJA θJATSOT;覆铜面积500 mm²typ 131 °C/W17
ΨJB ΨJB5引脚 TSOTtyp 43 °C/W17

Open-source boards using it

5
  • 4 layers69.8 × 69.8 mmFreeEEG32, the printed circuit board in 3D

    FreeEEG32

    neuroidss/FreeEEG32-alpha1.0

    ALPHA1.0 TEST FAILED, USE NEW VERSION INSTEAD FreeEEG32 alpha1.0 32 channels mobile electroencephalography under GNU AGPL 24 bits, 4kSPS ADCs 4x AD7770 MCU STM32F427ZI WIFI ESP-12F (ESP8266) USB CP2102N Accel & hyro…

    217 parts39AGPL-3.0
  • 2 layers91.6 × 65 mmSCARA, the printed circuit board in 3D

    SCARA

    jobitjoseph/SCARA-Robot-Based-on-ESP32-C6

    SCARA Robot Based on ESP32-C6

    67 parts4
  • 2 layers72.5 × 55 mmB PSU 0x00, the printed circuit board in 3D

    B PSU 0x00

    EmilsSturitis/BPSU

    Bipolar power supply board, for op-amp's and other things

    78 parts1
  • 2 layers52 × 100 mmCellgrading, the printed circuit board in 3D

    Cellgrading

    jobitjoseph/CellGradingTool

    87 parts
  • 4 layers66 × 76.2 mmFreeEEG32-alpha2, the printed circuit board in 3D

    FreeEEG32-alpha2

    neuroidss/FreeEEG32-alpha2

    209 partsAGPL-3.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ADP7118AUJZ-3.3-R7?

Yes. The symbol is EasyEDA_Cloud:ADPL44002AUJZ-1.8-R7 and the footprint Package_TO_SOT_SMD:TSOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ADP7118AUJZ-3.3-R7?

TSOT-5, with 5 pins. Its footprint is drawn on this page.

Where is the ADP7118AUJZ-3.3-R7 datasheet?

Analog Devices publishes it: the Datasheet link on this page opens it.

Where can I order the ADP7118AUJZ-3.3-R7?

JLCPCB lists it as part C194022, with 3,177 in stock; the sellers' links on this page open their listings.

What can replace the ADP7118AUJZ-3.3-R7?

Parts like it in the library: the ME6211C33M5G-N by MICRONE, the SPX3819M5-L-3-3/TR by MaxLinear, the RT9013-33GB by RICHTEK and the XC6219B332MR by UMW. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ADP7118AUJZ-3.3-R7?

5 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.