Skip to the content
1234567891011121314151617181920

AD8331ARQZ

Analog DevicesExtended

-4.5dB~55.5dB -40℃~+85℃ 1 120MHz 25mA 25mA 4.5V~5.5V 45mA 50000uV Differential VGA QSOP-20-150mil Programmable / Variable Gain Amplifiers (PGA/VGA) ROHS

Part id
adi/AD8331ARQZ
Category
Low Noise Amplifiers (LNA), RF
Package
QSOP-20-150mil
Pins
20
In stock
17 at JLCPCB (C203731)
Used on
8 open-source boards

Overview

The AD8331ARQZ is a low Noise Amplifiers (LNA), RF made by Analog Devices in a QSOP-20-150mil package with 20 pins. -4.5dB~55.5dB -40℃~+85℃ 1 120MHz 25mA 25mA 4.5V~5.5V 45mA 50000uV Differential VGA QSOP-20-150mil Programmable / Variable Gain Amplifiers (PGA/VGA) ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:AD8331ARQZ-RL, from EasyEDA) and its footprint (Package_SO:QSOP-20_3.9x8.7mm_P0.635mm, from KiCad's library), ready for a KiCad board. 17 are in stock at JLCPCB (part C203731). 8 open-source boards in 5 repositories on GitHub use it.

Symbol

1LMD2INH3VPSL4LON5LOP6COML7VIP8VIN9MODE10GAIN11VCM12RCLMP13HILO14VPOS15VOH16VOL17COMM18ENBV19ENBL20COMM
EasyEDA_Cloud:AD8331ARQZ-RLFrom EasyEDA

Footprint

1234567891011121314151617181920
Package_SO:QSOP-20_3.9x8.7mm_P0.635mmFrom KiCad's library

From the datasheet

8
Supply, least
4.5 V · VPSL, VPOS, recommended operating min · p. 6
Supply, most
5.5 V · VPSL, VPOS, recommended operating max · p. 6
Supply, absolute maximum
5.5 V · VPSL, VPOS, absolute max · p. 7
Works from
-40 °C · Operating temperature min · p. 7
Works up to
85 °C · Operating temperature max · p. 7
Takes working
25 mA · Quiescent current per channel typical · p. 6
Takes asleep
240 µA · Power-down current typical, VGA and LNA disabled · p. 6
Junction to air (RQ Package)
83 K/W · Junction to ambient, 4-layer JEDEC board · p. 7

What it is and has

13
Preamplifier
Ultralow noise preamplifier · p. 1
Voltage noise
0.74 nV/√Hz · p. 1
Current noise
2.5 pA/√Hz · p. 1
3 dB bandwidth
120 MHz · p. 1
Power
125 mW/channel · p. 1
LO gain range
−4.5 dB to +43.5 dB · p. 1
HI gain range
7.5 dB to 55.5 dB · p. 1
Output-referred noise
48 nV/√Hz typical · p. 1
Input impedance
Active input impedance matching · p. 1
ADC compatibility
Optimized for 10-bit/12-bit ADCs · p. 1
Output clamping
Selectable output clamping level · p. 1
Supply
Single 5 V supply operation · p. 1
Package
20-Lead QSOP · p. 8

Specifications

78
ParameterConditionsAs printedPage
GainSingle-ended input to differential outputtyp 19 dB4
GainInput to output (single-ended)typ 13 dB4
Input ResistanceRIZ = 280 Ωtyp 50 Ω4
Input ResistanceRIZ = 412 Ωtyp 75 Ω4
Input ResistanceRIZ = 562 Ωtyp 100 Ω4
Input ResistanceRIZ = 1.13 kΩtyp 200 Ω4
Input ResistanceRIZ = ∞typ 6 kΩ4
Input Capacitancetyp 13 pF4
Output ImpedanceSingle-ended, either outputtyp 5 Ω4
−3 dB Small Signal BandwidthVOUT = 0.2 V p-ptyp 130 MHz4
Slew Ratetyp 650 V/us4
Input Voltage NoiseRS = 0 Ω, HI or LO gain, RIZ = ∞, f = 5 MHztyp 0.74 nV/√Hz4
Input Current NoiseRIZ = ∞, HI or LO gain, f = 5 MHztyp 2.5 pA/√Hz4
Noise Figure — Active Termination Matchf = 10 MHz, LOP output; RS = RIN = 50 Ωtyp 3.7 dB4
Noise Figure — Unterminatedf = 10 MHz, LOP output; RS = 50 Ω, RIZ = ∞typ 2.5 dB4
Harmonic Distortion at LOP1 or LOP2 — HD2VOUT = 0.5 V p-p, single-ended, f = 10 MHztyp -56 dBc4
Harmonic Distortion at LOP1 or LOP2 — HD3VOUT = 0.5 V p-p, single-ended, f = 10 MHztyp -70 dBc4
Output Short-Circuit CurrentPin LON, Pin LOPtyp 165 mA4
−3 dB Small Signal BandwidthAD8331; VOUT = 0.2 V p-ptyp 120 MHz4
−3 dB Large Signal BandwidthAD8331; VOUT = 2 V p-ptyp 110 MHz4
Slew RateAD8331; LO gaintyp 300 V/us4
Slew RateAD8331; HI gaintyp 1200 V/us4
Input Voltage NoiseRS = 0 Ω, HI or LO gain, RIZ = ∞, f = 5 MHztyp 0.82 nV/√Hz4
Noise Figure — Active Termination MatchVGAIN = 1.0 V; RS = RIN = 50 Ω, f = 10 MHz, measuredtyp 4.15 dB4
Noise Figure — Active Termination MatchVGAIN = 1.0 V; RS = RIN = 200 Ω, f = 5 MHz, simulatedtyp 2 dB4
Noise Figure — UnterminatedVGAIN = 1.0 V; RS = 50 Ω, RIZ = ∞, f = 10 MHz, measuredtyp 2.5 dB4
Noise Figure — UnterminatedVGAIN = 1.0 V; RS = 200 Ω, RIZ = ∞, f = 5 MHz, simulatedtyp 1 dB4
Output-Referred NoiseAD8331; VGAIN = 0.5 V, LO gaintyp 48 nV/√Hz4
Output-Referred NoiseAD8331; VGAIN = 0.5 V, HI gaintyp 178 nV/√Hz4
Output Impedance, PostamplifierDC to 1 MHztyp 1 Ω4
Output Signal Range, Postamplifier — DifferentialRL ≥ 500 Ω, unclampedtyp 4.5 V p-p5
Output Offset VoltageAD8331; Differential, VGAIN = 0.5 Vmin -50 · max 50 mV5
Output Offset VoltageAD8331; Common modemin -125 · typ -25 · max 100 mV5
Output Short-Circuit Currenttyp 45 mA5
Harmonic Distortion — HD2AD8331; VGAIN = 0.5 V, VOUT = 1 V p-p, HI gain; f = 1 MHztyp -88 dBc5
Harmonic Distortion — HD3AD8331; VGAIN = 0.5 V, VOUT = 1 V p-p, HI gain; f = 1 MHztyp -85 dBc5
Harmonic Distortion — HD2AD8331; VGAIN = 0.5 V, VOUT = 1 V p-p, HI gain; f = 10 MHztyp -68 dBc5
Harmonic Distortion — HD3AD8331; VGAIN = 0.5 V, VOUT = 1 V p-p, HI gain; f = 10 MHztyp -65 dBc5
Input 1 dB Compression PointVGAIN = 0.25 V, VOUT = 1 V p-p, f = 1 MHz to 10 MHztyp 1 dBm5
Two-Tone Intermodulation Distortion (IMD3)AD8331; VGAIN = 0.72 V, VOUT = 1 V p-p, f = 1 MHztyp -80 dBc5
Two-Tone Intermodulation Distortion (IMD3)AD8331; VGAIN = 0.5 V, VOUT = 1 V p-p, f = 10 MHztyp -72 dBc5
Output Third-Order InterceptAD8331; VGAIN = 0.5 V, VOUT = 1 V p-p, f = 1 MHztyp 38 dBm5
Output Third-Order InterceptAD8331; VGAIN = 0.5 V, VOUT = 1 V p-p, f = 10 MHztyp 33 dBm5
Overload RecoveryVGAIN = 1.0 V, VIN = 50 mV p-p/1 V p-p, f = 10 MHztyp 5 ns5
Absolute Gain Error0.05 V < VGAIN < 0.10 Vmin -1 · typ 0.5 · max 2 dB5
Absolute Gain Error0.10 V < VGAIN < 0.95 Vmin -1 · max 1 dB5
Absolute Gain Error0.95 V < VGAIN < 1.0 Vmin -2 · typ -1 · max 1 dB5
Gain Scaling Factor0.10 V < VGAIN < 0.95 Vmin 48.5 · typ 50 · max 51.5 dB/V5
Input Impedancetyp 10 MΩ5
Response Time48 dB gain change to 90% full scaletyp 500 ns5
Input ResistanceCurrent limited to ±1 mAtyp 30 Ω5
Output CM Offset VoltageVCM = 2.5 Vmin -125 · typ -25 · max 100 mV5
Logic Level to Enable PowerPIN ENBL, PIN ENBVmin 2.25 · max 5 V6
Logic Level to Disable PowerPIN ENBL, PIN ENBVmin 0 · max 1 V6
Input ResistancePin ENBLtyp 40 kΩ6
Input ResistancePin ENBVtyp 70 kΩ6
Power-Up Response TimeVINH = 30 mV p-ptyp 300 us6
Power-Up Response TimeVINH = 150 mV p-ptyp 4 ms6
Logic Level to Select HI Gain Rangemin 2.25 · max 5 V6
Logic Level to Select LO Gain Rangemin 0 · max 1 V6
Input Resistancetyp 50 kΩ6
Logic Level for Positive Gain Slopemin 0 · max 1 V6
Logic Level for Negative Gain Slopemin 2.25 · max 5 V6
Input Resistancetyp 200 kΩ6
Supply VoltageAD8331; VPSL, VPOSmin 4.5 · typ 5 · max 5.5 V6
Quiescent Current per ChannelAD8331min 20 · typ 25 mA6
Power Dissipation per ChannelAD8331; No signaltyp 125 mW6
Power-Down CurrentAD8331; VGA and LNA disabledmin 50 · typ 240 · max 400 uA6
LNA CurrentAD8331 (ENBL); Each channelmin 7.5 · typ 11 · max 15 mA6
VGA CurrentAD8331 (ENBV)min 7.5 · typ 14 · max 20 mA6
PSRRVGAIN = 0 V, f = 100 kHztyp -68 dB6
Supply Voltage (VPSn, VPSV, VPSL, VPOS)AD8331; VPSL, VPOSmax 5.5 V7
GAIN Voltagemax 2.5 V7
Power DissipationRQ Package (AD8331); 4-layer JEDEC board (2S2P)max 0.78 W7
Operating Temperature Rangemin -40 · max 85 °C7
Storage Temperature Rangemin -65 · max 150 °C7
Lead Temperature (Soldering 60 sec)Soldering 60 secmax 300 °C7
θJA θJARQ Package (AD8331); 4-layer JEDEC board (2S2P)max 83 °C/W7

Pins, by the datasheet

20
1 LMD
LNA midsupply bypass; connect a capacitor for midsupply HF bypass. · p. 8
2 INH
LNA input. · p. 8
3 VPSL
LNA 5 V supply. · p. 8
4 LON
LNA inverting output. · p. 8
5 LOP
LNA noninverting output. · p. 8
6 COML
LNA ground. · p. 8
7 VIP
VGA noninverting input. · p. 8
8 VIN
VGA inverting input. · p. 8
9 MODE
Gain slope logic input. · p. 8
10 GAIN
Gain control voltage. · p. 8
11 VCM
Common-mode voltage. · p. 8
12 RCLMP
Output clamping level. · p. 8
13 HILO
Gain range select (HI or LO). · p. 8
14 VPOS
VGA 5 V supply. · p. 8
15 VOH
Noninverting VGA output. · p. 8
16 VOL
Inverting VGA output. · p. 8
17 COMM
VGA ground. · p. 8
18 ENBV
VGA enable. · p. 8
19 ENBL
LNA enable. · p. 8
20 COMM
VGA ground. · p. 8

Open-source boards using it

8
  • 2 layers35 × 50 mmGoblin, the printed circuit board in 3D

    Goblin

    kelu124/echomods

    Open source ultrasound processing modules and building blocks

    60 parts463
  • 4 layers87.1 × 78.2 mm3 in 1 Panel, the printed circuit board in 3D

    3 in 1 Panel

    kelu124/pic0rick

    An rp2040-based acquisition board for pulse-echo ultrasound

    115 parts116
  • 2 layers122 × 64 mmCurrent probe, the printed circuit board in 3D

    Current probe

    stgloorious/current-probe

    Experimental AD8331 amplifier board for measuring transient CPU power consumption

    370 parts3CC-BY-SA-4.0
  • 4 layers85 × 54 mmMsi SDR ADC, the printed circuit board in 3D

    Msi SDR ADC

    kelu124/oshmri

    OpenSourceHardware - going to MRI

    92 parts2
  • 4 layers85 × 54 mmPICO ADC Test, the printed circuit board in 3D

    PICO ADC Test

    kelu124/pic0rick

    An rp2040-based acquisition board for pulse-echo ultrasound

    66 parts116
  • 2 layers50 × 20 mmCurrent probe, the printed circuit board in 3D

    Current probe

    stgloorious/current-probe

    Experimental AD8331 amplifier board for measuring transient CPU power consumption

    74 parts3CC-BY-SA-4.0
  • 4 layers85 × 54 mmPICO ADC Test, the printed circuit board in 3D

    PICO ADC Test

    kelu124/oshmri

    OpenSourceHardware - going to MRI

    59 parts2
  • 4 layers117 × 60 mmCw lite main, the printed circuit board in 3D

    Cw lite main

    nikitalita/cw-kicad-conversions

    334 parts

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the AD8331ARQZ?

Yes. The symbol is EasyEDA_Cloud:AD8331ARQZ-RL and the footprint Package_SO:QSOP-20_3.9x8.7mm_P0.635mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AD8331ARQZ?

QSOP-20-150mil, with 20 pins. Its footprint is drawn on this page.

Where is the AD8331ARQZ datasheet?

Analog Devices publishes it: the Datasheet link on this page opens it.

Where can I order the AD8331ARQZ?

JLCPCB lists it as part C203731, with 17 in stock; the sellers' links on this page open their listings.

What can replace the AD8331ARQZ?

Parts like it in the library: the AD8331ARQZ-R7 by Analog Devices. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AD8331ARQZ?

8 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.