6 layers160 × 100 mm
2 layers86 × 50 mm
Gate Emission Regulator
Zychlix/ECRThis is an emiter cathode current regulator. It works via affecting gate potential in reference to grounded anode
- Size
- 86 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 23
- Pads
- 84
- Tracks, vias
- 221, 5
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 7 Jun 2025
- Updated
- 16 Jun 2025
Overview
Gate Emission Regulator is an open-source printed circuit board by Zychlix, from the Zychlix/ECR repository on GitHub. It is a 2-layer board of 86 × 50 mm with 36 parts on 23 nets, routed with 221 tracks and 5 vias.
It is built around the TL074ACNSR, C0805C105K4PAC and RT0805FRD071ML, with the 1N4148WS, RT0805FRE07100RL and RT0805FRE0710RL among its other parts. Its parts include 13 resistors, 5 capacitors, 4 diodes, 4 connectors and 2 ICs. It belongs with the power boards of this library.
Main components
8
TL074ACNSR
SOP-14-208mil-20V~20V 0℃~+70℃ 1.4mA 100dB 10V~30V 18nV/√Hz@1kHz 18uV/℃ 20V/us 3MHz 3mV 4 5pA 65pA Short-Circuit Protection、EMI filtering/RF suppression SOP-14-208mil FET Input Amplifiers ROHSTexas InstrumentsFET Input Amplifiers
C0805C105K4PAC
080516V 1uF X5R ±10% 0805 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSKEMETMultilayer Ceramic Capacitors MLCC - SMD/SMT
RT0805FRD071ML
0805-55℃~+155℃ 125mW 150V 1MΩ Thin Film Resistor ±1% ±25ppm/℃ 0805 Chip Resistor - Surface Mount ROHSYAGEOChip Resistor - Surface Mount
1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching DiodesRT0805FRE07100RL
0805-55℃~+155℃ 100Ω 125mW 150V Thin Film Resistor ±1% ±50ppm/℃ 0805 Chip Resistor - Surface Mount ROHSYAGEOChip Resistor - Surface MountRT0805FRE0710RL
0805-55℃~+155℃ 10Ω 125mW 150V Thin Film Resistor ±1% ±50ppm/℃ 0805 Chip Resistor - Surface Mount ROHSYAGEOChip Resistor - Surface MountGRM2165C2A103JA01D
0805100V 10nF C0G ±5% 0805 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSMurataMultilayer Ceramic Capacitors MLCC - SMD/SMT
BD135
TO-126-3-55℃~+150℃ 1 NPN 1.25W 1.5A 100nA 250 45V 500mV 5V NPN TO-126-3 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
README.mdECR
Parts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 1u | Capacitor_SMD:C_0805_2012Metric | C2, C3, C4, C5 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R4, R11, R13 |
| 3 | 1M | Resistor_SMD:R_0805_2012Metric | R2, R3, R10 |
| 3 | 1N4148 | Diode_SMD:D_SOD-323F | D1, D2, D3 |
| 3 | 1k | Resistor_SMD:R_0805_2012Metric | R1, R5, R12 |
| 2 | 100R | Resistor_SMD:R_0805_2012Metric | R6, R9 |
| 2 | 10R | Resistor_SMD:R_0805_2012Metric | R7, R8 |
| 1 | 10k | Potentiometer_THT:Potentiometer_Alps_RK163_Single_Horizontal | RV3 |
| 1 | 10k | Potentiometer_THT:Potentiometer_Bourns_3296Y_Vertical | RV2 |
| 1 | 10n | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | BD135 | Package_TO_SOT_THT:TO-126-3_Vertical | Q1 |
| 1 | GAIN | MEMS_Passive:R_0805_2012Metric_Jumper_Open | SW1 |
| 1 | GATE | TestPoint:TestPoint_THTPad_2.5x2.5mm_Drill1.2mm | J2 |
| 1 | GND | TestPoint:TestPoint_THTPad_2.5x2.5mm_Drill1.2mm | J3 |
| 1 | Iwe | TestPoint:TestPoint_THTPad_2.5x2.5mm_Drill1.2mm | J4 |
| 1 | RED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | SW_SPST | MEMS_Passive:R_0805_2012Metric_Jumper_Open | SW2 |
| 1 | Screw_Terminal_01x03 | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mm | J1 |
| 1 | TL074 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U4 |
| 1 | ~ | MEMS_IC:P1-600 APD | U3 |
The 33 most common of 36 parts.
Questions
How big is the Gate Emission Regulator PCB?
It measures 86 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Gate Emission Regulator use?
36 parts, built around the TL074ACNSR, C0805C105K4PAC, RT0805FRD071ML and 1N4148WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gate Emission Regulator KiCad files?
From the Zychlix/ECR repository on GitHub, at the commit this page was made from: the board is Gate_Emission_Regulator.kicad_pcb and its schematic Gate_Emission_Regulator.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gate Emission Regulator design in my own project?
Its repository states no licence, so its author keeps all rights: ask Zychlix before reusing the design.
Similar boards
- 2 layers131.8 × 99.9 mm
- 2 layers81.9 × 62.5 mm
Lapse O Matic PCB
curiouselectric/Lapse-O-Matic
This is code, PCB and enclosure design for an ESP32_CAM based wildlife camera
40 parts44 - 2 layers98 × 83.8 mm
Projeto placa
phfbertoleti/placa_lorawan
Repositório oficial da placa LoRaWAN, um kit de desenvolvimento para protótipos IoT.
39 parts19MIT - 4 layers308 × 225.4 mm
- 2 layers117 × 95 mm
1 dc psu
arafat-siju/electronics-projects
A hardware-based fastest finger quiz system using digital logic ICs, featuring timer control, first-response detection, input lockout, and timeout indication.
50 parts - 2 layers70.3 × 57.5 mm
- 2 layers200 × 100 mm
