

Filltest
- Size
- 191 × 130 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 193
- Nets
- 138
- Pads
- 712
- Tracks, vias
- 0, 12
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 17 Feb 2026
- Updated
- 7 Nov 2026
Overview
Filltest is an open-source printed circuit board by zOnlyKroks, from the zOnlyKroks/pcb-consortium repository on GitHub, published under the CC0-1.0 licence. It is a 4-layer board of 191 × 130 mm with 193 parts on 138 nets.
It is built around the TPS54531DDA, BQ25798RQMR and CAT24C512WI-GT3, with the TPS25751DREFR, BQ7791501PW and LM339 among its other parts. Its parts include 85 capacitors, 54 resistors, 11 ICs, 9 diodes and 5 connectors.
Main components
12TPS54531DDA
SO-8-40℃~+85℃@(TA) 1 110uA 3.5V~28V 570kHz 5A 800mV~26.04V Adjustable Buck Buck Built-in No SO-8 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersBQ25798RQMR
QFN-29(4x4)-40℃~+85℃ 17uA 1~4 3.6V~24V 5A Charging IC I2C Lithium Battery Support QFN-29(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementCAT24C512WI-GT3
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.8V~5.5V 100 Years 1MHz 512Kbit 5ms I2C SOIC-8 EEPROM ROHSonsemiEEPROMTPS25751DREFR
WQFN-38(6x4)Port power switch control、Internal regulator、Overcurrent Protection、ESD protection、PD protocol support、Downstream port power switch、BC1.2 protocol support、Error detection and recovery WQFN-38(6x4) USB HUB Controllers ROHSTexas InstrumentsUSB HUB ControllersBQ7791501PW
TSSOP-24-40℃~+85℃ 2.9V 2uA 3V~25V 3~5 4.2V 50mA 60mA Support TSSOP-24 Battery Management ROHSTexas InstrumentsBattery ManagementLM339
SOP-140℃~+70℃ 1.1mA 1.5mV 150ns 2.3nA 2V~32V 32V 57nA DTL、TTL、CMOS Four channels Open Collector SOP-14 Comparators ROHSJSMSEMIComparatorsME6211C33M5G-N
SOT-23-5-40℃~+150℃ 1 120mV@(100mA) 3.3V 500mA 50uVrms 60uA 6V 70dB@(1kHz) Fixed Over Current Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMICRONEVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTL431B
SOT-23-20℃~+70℃@(Ta) 150mA 1uA 2.5V~36V 2.5V~36V 250uA Adjustable Parallel ±0.3% SOT-23 Voltage Reference ROHShongjiachengVoltage ReferenceAON6512
PDFN-8(5.2x5.6)1 N-channel 1.327nF 1.7mΩ@10V 150A 175pF 2V 3.43nF 30V 53nC@10V 83W PDFN-8(5.2x5.6) MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsTVS2200DRV
WSON-6-EP(2x2)-40℃~+125℃ 1.12kW@8/20us 105pF 22V 25.9V 28V 3.5nA 40A@8/20us IEC 61000-4-2、IEC 61000-4-5 TVS Unidirectional WSON-6-EP(2x2) ESD and Surge Protection (TVS/ESD) ROHSTexas InstrumentsESD And Surge Protection (TVS/ESD)TYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB ConnectorsSS54
SMA(DO-214AC)-55℃~+125℃ 1mA@40V 40V 550mV@5A 5A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
README.mdPCB / Circuit Designs
Support & Issues
If something is broken, unclear, or you need help assembling:
- Open a GitHub Issue
- I’ll try to help when I can
Use at your own risk 🙂
Parts
193| Qty | Value | Footprint | References |
|---|---|---|---|
| 32 | 10uF 50V | Capacitor_SMD:C_1206_3216Metric | C201, C208, C209, C210, C211, C214, C215, C216, C220, C221, C222, C223, C224, C226, C227, C301 +16 |
| 21 | 100nF | Capacitor_SMD:C_0603_1608Metric | C103, C104, C105, C106, C107, C108, C109, C110, C212, C213, C217, C225, C228, C312, C313, C317 +5 |
| 9 | 100R | Resistor_SMD:R_0603_1608Metric | R102, R103, R104, R105, R106, R112, R113, R204, R304 |
| 9 | 10k | Resistor_SMD:R_0603_1608Metric | R107, R108, R110, R203, R303, R407, R408, R409, R416 |
| 8 | 18650 | PowerbankV2:BatteryHolder_BH-18650-B1BA002 | BT101, BT102, BT103, BT104, BT105, BT106, BT107, BT108 |
| 6 | 10uF | Capacitor_SMD:C_0603_1608Metric | C202, C203, C204, C302, C303, C304 |
| 6 | 1k | Resistor_SMD:R_0603_1608Metric | R101, R116, R208, R308, R411, R412 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C101, C102, C412, C413 |
| 4 | 2.2k | Resistor_SMD:R_0603_1608Metric | R201, R202, R301, R302 |
| 4 | 330pF | Capacitor_SMD:C_0603_1608Metric | C206, C207, C306, C307 |
| 4 | 47nF | Capacitor_SMD:C_0603_1608Metric | C218, C219, C318, C319 |
| 4 | 47uF 10V | Capacitor_SMD:C_1206_3216Metric | C408, C409, C410, C411 |
| 4 | 4x10k | Resistor_SMD:R_Array_Convex_4x0603 | RN201, RN202, RN301, RN302 |
| 4 | 6.8k | Resistor_SMD:R_0603_1608Metric | R417, R418, R419, R420 |
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3 | H401, H402, H403, H404 |
| 3 | 10k B3380 | Resistor_SMD:R_0603_1608Metric | RT101, RT201, RT301 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R109, R406 |
| 2 | 10nF | Capacitor_SMD:C_0603_1608Metric | C403, C404 |
| 2 | 1M | Resistor_SMD:R_0603_1608Metric | R115, R117 |
| 2 | 1nF | Capacitor_SMD:C_0603_1608Metric | C230, C330 |
| 2 | 2.2uH | PowerbankV2:L_7.0x6.6_MWSA0603S | L201, L301 |
| 2 | 22uF 25V | Capacitor_SMD:C_0805_2012Metric | C205, C305 |
| 2 | 27k | Resistor_SMD:R_0603_1608Metric | R207, R307 |
| 2 | 30.1k | Resistor_SMD:R_0603_1608Metric | R206, R306 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric | R114, R410 |
| 2 | 4.7uF 25V | Capacitor_SMD:C_0805_2012Metric | C229, C329 |
| 2 | 5.23k | Resistor_SMD:R_0603_1608Metric | R205, R305 |
| 2 | AON6512 | PowerbankV2:PDFN-8_5x6_AON6512 | Q101, Q102 |
| 2 | BQ25798RQM | Package_DFN_QFN:Texas_RQM0029A_VQFN-29_4x4mm_P0.4mm | U203, U303 |
| 2 | CAT24C512WI | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U202, U302 |
| 2 | CHG | LED_SMD:LED_0603_1608Metric | D202, D302 |
| 2 | EE_PROG | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J202, J302 |
| 2 | EE_PWR | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP201, JP301 |
| 2 | TPS25751DREF | PowerbankV2:Texas_REF0038A_WQFN-38-2EP_6x4mm_P0.4_Via0.3 | U201, U301 |
| 2 | TVS2200 | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | D201, D301 |
| 2 | TYPE-C-31-M-12 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J201, J301 |
| 1 | 1.5k | Resistor_SMD:R_0603_1608Metric | R413 |
| 1 | 1.96k | Resistor_SMD:R_0603_1608Metric | R404 |
| 1 | 1/4 | LED_SMD:LED_0603_1608Metric | D402 |
| 1 | 10.5k | Resistor_SMD:R_0603_1608Metric | R403 |
| 1 | 130k | Resistor_SMD:R_0603_1608Metric | R402 |
| 1 | 15k | Resistor_SMD:R_0603_1608Metric | R414 |
| 1 | 2.2nF | Capacitor_SMD:C_0603_1608Metric | C406 |
| 1 | 2/4 | LED_SMD:LED_0603_1608Metric | D403 |
| 1 | 20A | PowerbankV2:Fuse_10.3x3.2_1032 | F101 |
| 1 | 22pF | Capacitor_SMD:C_0603_1608Metric | C407 |
| 1 | 2mR | Resistor_SMD:R_2512_6332Metric | R111 |
| 1 | 3/4 | LED_SMD:LED_0603_1608Metric | D404 |
| 1 | 37.4k | Resistor_SMD:R_0603_1608Metric | R405 |
| 1 | 4.7uH | PowerbankV2:L_11x10_TMPA1004S | L401 |
| 1 | 4/4 | LED_SMD:LED_0603_1608Metric | D405 |
| 1 | 470k | Resistor_SMD:R_0603_1608Metric | R118 |
| 1 | 51k | Resistor_SMD:R_0603_1608Metric | R415 |
| 1 | 665k | Resistor_SMD:R_0603_1608Metric | R401 |
| 1 | BQ7791501 | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U101 |
| 1 | GAUGE | PowerbankV2:SW_TS-1187A_5.1x5.1 | SW402 |
| 1 | LM339 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U403 |
| 1 | ME6211C33M5G | Package_TO_SOT_SMD:SOT-23-5 | U402 |
| 1 | PD_HOST | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J401 |
| 1 | PD_RESET | PowerbankV2:SW_TS-1187A_5.1x5.1 | SW401 |
| 1 | SS54 | Diode_SMD:D_SMA | D401 |
| 1 | TL431B | Package_TO_SOT_SMD:SOT-23 | U404 |
| 1 | TPS54531DDA | Package_SO:TI_SO-PowerPAD-8_ThermalVias | U401 |
More from zOnlyKroks/pcb-consortium
12- 4 layers66 × 155 mm

- 2 layers117.1 × 40.9 mm

- 4 layers165 × 125 mm

- 4 layers170 × 90 mm

- 4 layers230 × 77.6 mm

- 6 layers100 × 100 mm

- 4 layers126.3 × 115.4 mm

- 4 layers64.5 × 74.8 mm

- 4 layers128 × 60 mm

- 2 layers112 × 68 mm

- 2 layers80 × 40.3 mm

- 4 layers49.9 × 99.8 mm

Similar boards
- 4 layers70 × 50 mm

BMS V3
Shubhroto-M/Vanguard-25-BMS
A 5S 20A Battery Management System featuring a dual-redundant safety architecture and a BQ7718 hardware kill switch.
99 parts - 4 layers100 × 27 mm

Props board v3
ephemeridis/props_board
ESP32 based control board for costumes and props featuring USB PD enabled charging
188 partsGPL-3.0 - 2 layers

Usb
wozniak-works/X1-palmrest-to-keyboard
A custom replacement board for the Lenovo ThinkPad X1 Carbon palmrest to transform it to keyboard with integrated powerbank and usb hub.
186 parts - 6 layers43.2 × 74.4 mm

Monolith
MidwestMotorBoy/Battery-Bank
Monolith: an ultralight IP67 power bank for backpacking. 4S BAK 65E 21700 (91 Wh, under the 100 Wh airline limit), two bidirectional 100 W USB-C PD ports, Bluetooth LE (TI CC2340) with an iPhone app.
289 parts - 2 layers130 × 75 mm

- 4 layers146 × 95 mm

- 4 layers100 × 100 mm

Smc power
efebasol/StepperMotorController
Rev A — single-motor bench prototype power board. Feeds the driver board (48 V), the stepper motor brake (24 V) and the logic (5 V / 3V3).
104 parts - 2 layers92.4 × 42.4 mm

Mw1
falseywinchnet/hf-active-antennas
Open-hardware HF receive-antenna amplifiers: zero-flux loop amp, loop LNA, mini-whip. LTspice models, KiCad boards, JLCPCB packages. see license
109 parts
Questions
How big is the Filltest PCB?
It measures 191 × 130 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Filltest use?
193 parts, built around the TPS54531DDA, BQ25798RQMR, CAT24C512WI-GT3 and TPS25751DREFR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Filltest KiCad files?
From the zOnlyKroks/pcb-consortium repository on GitHub, at the commit this page was made from: the board is Powerbank/V2/route/filltest.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Filltest design in my own project?
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).