Skip to the content
WQFN-38(6x4)

TPS25751DREFR

Texas InstrumentsExtended

Port power switch control、Internal regulator、Overcurrent Protection、ESD protection、PD protocol support、Downstream port power switch、BC1.2 protocol support、Error detection and recovery WQFN-38(6x4) USB HUB Controllers ROHS

Part id
ti/TPS25751DREFR
Category
USB HUB Controllers
Package
WQFN-38(6x4)
Pins
44
In stock
0 at JLCPCB (C30169739)
Used on
3 open-source boards

Overview

The TPS25751DREFR is a USB HUB Controller made by Texas Instruments in a WQFN-38(6x4) package with 44 pins. Port power switch control、Internal regulator、Overcurrent Protection、ESD protection、PD protocol support、Downstream port power switch、BC1.2 protocol support、Error detection and recovery WQFN-38(6x4) USB HUB Controllers ROHS.

JLCPCB lists it (part C30169739). 3 open-source boards in 3 repositories on GitHub use it.

Symbol

The library has no symbol for this part yet.

Footprint

The library has no footprint for this part yet.

From the datasheet

29
Supply, least
3 V · VIN_3V3, recommended operating min · p. 8
Supply, most
3.6 V · VIN_3V3, recommended operating max · p. 8
Supply, least
4.9 V · PP5V, recommended operating min · p. 8
Supply, most
5.5 V · PP5V, recommended operating max · p. 8
Supply, least
4 V · VBUS_IN and VBUS, recommended operating min · p. 8
Supply, most
22 V · VBUS_IN and VBUS, recommended operating max · p. 8
Supply, absolute maximum
4 V · VIN_3V3, absolute max · p. 7
Supply, absolute maximum
6 V · PP5V, absolute max · p. 7
Supply, absolute maximum
28 V · VBUS_IN and VBUS, absolute max · p. 7
Junction, hottest
175 °C · Operating junction temperature, absolute max · p. 7
Takes working
3 mA · VIN_3V3, Active Source mode, 3.3 V, typical · p. 11
Takes at most
6 mA · VIN_3V3, Active Sink mode, 3.3 V, max · p. 11
Takes asleep
58 µA · sum of VIN_3V3 and PP5V sleep currents, typical · p. 11
Gives
3 A · PP5V to VBUS sourcing output, max · p. 8
Gives
5 A · PPHV bidirectional load switch, rated max · p. 1
A pin gives at most
5 mA · GPIOx source current, absolute max · p. 7
Current limit
1.15 A · PP5V current limit, setting 0, min · p. 11
Current limit
1.61 A · PP5V current limit, setting 1, min · p. 11
Current limit
2.3 A · PP5V current limit, min · p. 11
Current limit
3.04 A · PP5V current limit, setting 3, min · p. 11
Current limit
3.22 A · PP5V current limit, setting 4, min · p. 11
Current limit
410 mA · VCONN short circuit current limit, setting 0, typical · p. 15
Current limit
600 mA · VCONN short circuit current limit, setting 1, typical · p. 15
Junction to air (QFN)
57.4 K/W · Sinking through PP_HV, typical · p. 10
Junction to air (QFN)
46.5 K/W · Sourcing through PP_5V, typical · p. 10
Junction to case (QFN)
30.5 K/W · Top, sinking through PP_HV, typical · p. 10
Junction to case (QFN)
20.3 K/W · Top, sourcing through PP_5V, typical · p. 10
Junction to board (QFN)
21.1 K/W · Sinking through PP_HV, typical · p. 10
Junction to board (QFN)
11.1 K/W · Sourcing through PP_5V, typical · p. 10

What it is and has

12
USB PD certification
USB-IF certified for PD3.1 · p. 1
USB-IF TID
10306 · p. 1
Battery charger control
Integrated I2C control for TI battery chargers · p. 1
Configuration
Web-based GUI and pre-configured firmware · p. 1
Programmable Power Supply
PPS source and sink · p. 1
Liquid detection
Measures directly at the Type-C connector · p. 1
Sourcing switch
Integrated 5 V, 3 A, 36 mΩ · p. 1
Bidirectional load switch
Integrated 20 V, 5 A, 16 mΩ · p. 1
CC pin tolerance
26 V · p. 1
GPIO
10 configurable · p. 1
BC1.2
Advertisement/detection support · p. 1
Package
QFN (REF), 4.0mm x 6.0mm · p. 1

Around it

7
cap 10 µF
between VIN_3V3 and GND; Nominal capacitance; minimum 5 uF; voltage rating 6.3 V; account for derating. · p. 9
cap 10 µF
between LDO_3V3 and GND; Nominal capacitance; range 5–25 uF; voltage rating 6.3 V; account for derating. · p. 9
cap 4.5–12 µF
between LDO_1V5 and GND; Voltage rating 4 V; account for derating. · p. 9
cap 4.7 µF
between VBUS and GND; Nominal capacitance; range 1–10 uF; voltage rating 25 V; higher capacitance recommended when configured to quickly disable sinking path. · p. 9
cap 120 µF
between PP5V and GND; Minimum capacitance; voltage rating 10 V; keep at least 10 uF tied directly to PP5V. · p. 9
cap 47 µF
between PPHV and GND; TPS25751D sink bulk capacitance; nominal 47 uF, maximum 100 uF; voltage rating 25 V. · p. 9
cap 400 pF
between CC1 and GND; Nominal total external capacitance; range 200–480 pF; voltage rating 6.3 V; includes capacitance to Type-C receptacle. · p. 9

Specifications

272
ParameterConditionsAs printedPage
Input voltage rangePP5Vmin -0.3 · max 6 V7
Input voltage rangeVIN_3V3min -0.3 · max 4 V7
Input voltage rangeADCIN1, ADCIN2min -0.3 · max 4 V7
Input voltage rangeVBUS_IN, VBUSmin -0.3 · max 28 V7
Input voltage rangeCC1, CC2min -0.5 · max 26 V7
Input voltage rangeGPIOxmin -0.3 · max 6 V7
Input voltage rangeI2Cc_SDA, I2Cc_SCL, I2Cc_IRQ, I2Ct_IRQ,I2Ct_SCL, I2Ct_SDAmin -0.3 · max 4 V7
Output voltage rangeLDO_1V5; do not apply voltage to this pinmin -0.3 · max 2 V7
Output voltage rangeLDO_3V3; do not apply voltage to this pinmin -0.3 · max 4 V7
Source currentPositive source current on CC1, CC2max 1 A7
Source currentGPIOxmax 0.005 A7
Operating junction temperature TJmin -40 · max 175 °C7
Storage temperature TSTGmin -55 · max 150 °C7
Input voltage rangePPHV; TPS25751Dmin -0.3 · max 28 V7
Source-to-source voltage VPPHV_VBUS_INTPS25751Dmax 28 V7
Sink currentTPS25751D; continuous current to/from VBUS_IN to PPHVmax 7 A7
Sink currentTPS25751D; pulsed current to/from VBUS_IN to PPHV; pulse duration ≤ 100 us and duty-cycle ≤ 1%max 10 A7
Operating junction temperature TJ_PPHVTPS25751D; PP_HV switchmin -40 · max 175 °C7
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±1000 Vmin -1000 · max 1000 V8
Electrostatic discharge V(ESD)Charged-device model (CDM), per ANSI/ESDA/JEDEC JS-002, all pins; ±500 Vmin -500 · max 500 V8
Input voltage range VITPS25751D; VIN_3V3min 3 · max 3.6 V8
Input voltage range VITPS25751D; PP5Vmin 4.9 · max 5.5 V8
Input voltage range VITPS25751D; ADCIN1, ADCIN2,VBUS_IN, VBUS, as printedmin 4 · max 22 V8
Input voltage range VITPS25751D; PPHVmin 0 · max 22 V8
I/O voltage range VIOTPS25751D; I2Cx_SDA, I2Cx_SCL, I2Cx_IRQ, ADCIN1, ADCIN2min 0 · max 3.6 V8
I/O voltage range VIOTPS25751D; GPIOxmin 0 · max 5.5 V8
I/O voltage range VIOTPS25751D; CC1, CC2min 0 · max 5.5 V8
Output current (from PP5V) IOTPS25751D; VBUSmax 3 A8
Output current (from PP5V) IOTPS25751D; CC1, CC2max 315 mA8
Output current (from LDO_3V3) IOTPS25751D; GPIOxmax 1 mA8
Operating junction temperature TJTPS25751Dmin -40 · max 125 °C8
Capacitance on VIN_3V3 CVIN_3V36.3 V voltage rating; NOM column recorded as typmin 5 · typ 10 uF9
Capacitance on LDO_3V3 CLDO_3V36.3 V voltage rating; NOM column recorded as typmin 5 · typ 10 · max 25 uF9
Capacitance on LDO_1V5 CLDO_1V54 V voltage ratingmin 4.5 · max 12 uF9
Capacitance on VBUS CVBUS25 V voltage rating; NOM column recorded as typmin 1 · typ 4.7 · max 10 uF9
Capacitance on PP5V CPP5V10 V voltage rating; keep at least 10 uF tied directly to PP5Vmin 120 uF9
Capacitance on PPHV Sink from VBUS CPPHVTPS25751D; 25 V voltage rating; NOM column recorded as typtyp 47 · max 100 uF9
Capacitance on CCy pins CCCy6.3 V voltage rating; includes all external capacitance to Type-C receptacle; NOM column recorded as typmin 200 · typ 400 · max 480 pF9
Junction-to-ambient thermal resistance RθJATPS25751D; QFN, 38 PINS; sinking through PP_HVtyp 57.4 °C/W10
Junction-to-ambient thermal resistance RθJATPS25751D; QFN, 38 PINS; sourcing through PP_5Vtyp 46.5 °C/W10
Junction-to-case (top) thermal resistance RθJC (top)TPS25751D; QFN, 38 PINS; sinking through PP_HVtyp 30.5 °C/W10
Junction-to-case (top) thermal resistance RθJC (top)TPS25751D; QFN, 38 PINS; sourcing through PP_5Vtyp 20.3 °C/W10
Junction-to-board thermal resistance RθJBTPS25751D; QFN, 38 PINS; sinking through PP_HVtyp 21.1 °C/W10
Junction-to-board thermal resistance RθJBTPS25751D; QFN, 38 PINS; sourcing through PP_5Vtyp 11.1 °C/W10
Junction-to-top characterization parameter ψJTTPS25751D; QFN, 38 PINS; sinking through PP_HVtyp 18.2 °C/W10
Junction-to-top characterization parameter ψJTTPS25751D; QFN, 38 PINS; sourcing through PP_5Vtyp 1 °C/W10
Junction-to-board characterization parameter ψJBTPS25751D; QFN, 38 PINS; sinking through PP_HVtyp 21.1 °C/W10
Junction-to-board characterization parameter ψJBTPS25751D; QFN, 38 PINS; sourcing through PP_5Vtyp 11.1 °C/W10
Junction-to-case (bottom GND pad) thermal resistance RθJC (bot_GND)TPS25751D; QFN, 38 PINStyp 1.8 °C/W10
Junction-to-case (bottom DRAIN pad) thermal resistance RθJC (bot_DRAIN)TPS25751D; QFN, 38 PINStyp 4.6 °C/W10
VBUS UVLO threshold VVBUS_UVLOrising; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 3.6 · max 3.9 V11
VBUS UVLO threshold VVBUS_UVLOfalling; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 3.5 · max 3.8 V11
VBUS UVLO threshold VVBUS_UVLOhysteresis; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vtyp 0.1 V11
Voltage required on VIN_3V3 for power on VVIN3V3_UVLOrising, VVBUS = 0min 2.56 · typ 2.66 · max 2.76 V11
Voltage required on VIN_3V3 for power on VVIN3V3_UVLOfalling, VVBUS = 0min 2.44 · typ 2.54 · max 2.64 V11
Voltage required on VIN_3V3 for power on VVIN3V3_UVLOhysteresistyp 0.12 V11
Voltage on LDO_3V3 VLDO_3V3VVIN_3V3 = 0 V, 10 uA ≤ ILOAD ≤ 18 mA, VBUS ≥ 3.9 Vmin 3 · typ 3.4 · max 3.6 V11
Rdson of VIN_3V3 to LDO_3V3 RLDO_3V3ILDO_3V3 = 50 mA; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmax 1.4 Ω11
Voltage on LDO_1V5 VLDO_1V5up to maximum internal loading condition; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 1.49 · typ 1.5 · max 1.65 V11
Current into VIN_3V3 IVIN_3V3,ActSrcActive Source mode: VVBUS = 5.0 V, VVIN_3V3 = 3.3 V; no GPIO loadingtyp 3 mA11
Current into VIN_3V3 IVIN_3V3,ActSnkActive Sink mode: 22 V ≥ VVBUS ≥ 4.0 V, VVIN_3V3 = 3.3 V; no GPIO loadingtyp 3 · max 6 mA11
Current into VIN_3V3 IVIN_3V3,IdlSrcIdle Source mode: VVBUS = 5.0 V, VVIN_3V3 = 3.3 V; no GPIO loadingtyp 1 mA11
Current into VIN_3V3 IVIN_3V3,IdlSnkIdle Sink mode: 22 V ≥ VVBUS ≥ 4.0 V, VVIN_3V3 = 3.3 V; no GPIO loadingtyp 1 mA11
Power drawn into PP5V and VIN_3V3 in Modern Standby Sink Mode PMstbySnkCCm floating, VCCn = 0.4 V, VPP5V = 5 V, VVIN_3V3 = 3.3 V, VVBUS = 5.0 V, GATE_VBUS, GATE_VSYS disabled, and TJ = 25°C; no GPIO loadingtyp 4.1 mW11
Power drawn into PP5V and VIN_3V3 in Modern Standby Source Mode PMstbySrcCCm floating, CCn tied to GND through 5.1 kΩ, VPP5V = 5 V, VVIN_3V3 = 3.3 V, IVBUS = 0, TJ = 25°C; no GPIO loadingtyp 4.5 mW11
Current into PP5V IPP5V,SleepSleep mode: VPA_VBUS = 0 V, VVIN_3V3 = 3.3 V; no GPIO loadingtyp 2 uA11
Current into VIN_3V3 IVIN_3V3,SleepSleep mode: VVBUS = 0 V, VVIN_3V3 = 3.3 V; no GPIO loadingtyp 56 uA11
Resistance from PP5V to VBUS RPP_5VILOAD = 3 A, TJ = 25°C; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vtyp 36 · max 38 mΩ11
Resistance from PP5V to VBUS RPP_5VILOAD = 3 A,TJ = 125°C; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vtyp 36 · max 53 mΩ11
VBUS to PP5V leakage current IPP5V_REVVPP5V = 0 V, VVBUS = 5.5 V, PP_5V disabled, TJ ≤ 85°C, measure IPP5Vmax 5 uA11
PP5V to VBUS leakage current IPP5V_FWDVPP5V = 5.5 V, VVBUS = 0 V, PP_5V disabled, TJ ≤ 85°C, measure IVBUSmax 15 uA11
Current limit setting ILIM5VConfigure to setting 0; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 1.15 · max 1.36 A11
Current limit setting ILIM5VConfigure to setting 1; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 1.61 · max 1.9 A11
Current limit setting ILIM5V3.0 V ≤ VVIN_3V3 ≤ 3.6 V; setting unspecified in rowmin 2.3 · max 2.7 A11
Current limit setting ILIM5VConfigure to setting 3; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 3.04 · max 3.58 A11
Current limit setting ILIM5VConfigure to setting 4; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 3.22 · max 3.78 A11
PP5V to VBUS current sense accuracy IVBUS3.64 A ≥ IVBUS ≥ 1 A; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 3.05 · typ 3.5 · max 3.75 A/V12
RCP clears and PP_5V starts turning on when VVBUS – VPP5V < VPP_5V_RCP. Measure VVBUS – VPP5V VPP_5V_RCP3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 10 · max 20 mV12
Response time to VBUS short circuit tiOS_PP_5VVBUS to GND through 10 mΩ, CVBUS = 0; 3.0 V ≤ VVIN_3V3 ≤ 3.6 Vtyp 1.15 us12
Response time to VVBUS > VOVP4RCP tPP_5V_ovpEnable PP_5V, IRpDef being drawn from PP5V, configure VOVP4RCP to setting 2, ramp VVBUS from 4V to 20 V at 100 V/ms, CPP5V = 2.5 uF, measure time from OVP detection until reverse current < 100 mAtyp 4.5 us12
Response time to VPP5V < VPP5V_UVLO, PP_VBUS is deemed off when VVBUS < 0.8 V tPP_5V_uvloRL = 100 Ω, no external capacitance on VBUStyp 4 us12
Response time to VPP5V < VVBUS + VPP_5V_RCP tPP_5V_rcpVPP5V = 5.5 V, IRpDef being drawn from PP5V, enable PP_5V, configure VOVP4RCP to setting 2, ramp VVBUS from 4 V to 21.5 V at 10 V/us, measure VPP5V. CPP5V = 104 uF, CVBUS=10 uF, measure time from RCP detection until reverse current < 100 mAtyp 0.7 us12
Current clamping deglitch time tILIM3.0 V ≤ VVIN_3V3 ≤ 3.6 Vtyp 5.1 ms12
From enable signal to VBUS at 90% of final value tONRL = 100 Ω, VPP5V = 5 V, CL = 0min 2.3 · typ 3.3 · max 4.3 ms12
From disable signal to VBUS at 10% of final value tOFFRL = 100 Ω, VPP5V = 5 V, CL = 0min 0.3 · typ 0.45 · max 0.6 ms12
VBUS from 10% to 90% of final value tRISERL = 100 Ω, VPP5V = 5 V, CL = 0min 1.2 · typ 1.7 · max 2.2 ms12
VBUS from 90% to 10% of initial value tFALLRL = 100 Ω, VPP5V = 5 V, CL = 0min 0.06 · typ 0.1 · max 0.14 ms12
Comparator mode RCP threshold, VPPHV - VVBUS VRCPTPS25751D; Setting 0, 4 V ≤ VVBUS ≤ 22 V, VVIN_3V3 ≤ 3.63 Vmin 2 · typ 6 · max 10 mV12
Comparator mode RCP threshold, VPPHV - VVBUS VRCPTPS25751D; setting 1, 4 V ≤ VVBUS ≤ 22 V, VVIN_3V3 ≤ 3.63 Vmin 4 · typ 8 · max 12 mV12
Comparator mode RCP threshold, VPPHV - VVBUS VRCPTPS25751D; Setting 2, 4 V ≤ VVBUS ≤ 22 V, VVIN_3V3 ≤ 3.63 Vmin 6 · typ 10 · max 14 mV12
Comparator mode RCP threshold, VPPHV - VVBUS VRCPTPS25751D; Setting 3, 4 V ≤ VVBUS ≤ 22 V, VVIN_3V3 ≤ 3.63 Vmin 8 · typ 12 · max 16 mV12
Soft start slew rate for GATE_VSYS, setting 0 SSTPS25751D; 4 V ≤ VVBUS ≤ 22 V, ILOAD = 100 mA, 500 pF < CGATE_VSYS < 16 nF, measure slope from 10% to 90% of final VSYS valuemin 0.35 · typ 0.41 · max 0.47 V/ms13
Soft start slew rate for GATE_VSYS, setting 1 SSTPS25751D; 4 V ≤ VVBUS ≤ 22 V, ILOAD = 100 mA, 500 pF < CGATE_VSYS < 16 nF, measure slope from 10% to 90% of final VSYS valuemin 0.67 · typ 0.81 · max 0.95 V/ms13
Soft start slew rate for GATE_VSYS, setting 2 SSTPS25751D; 4 V ≤ VVBUS ≤ 22 V, ILOAD = 100 mA, 500 pF < CGATE_VSYS < 16 nF, measure slope from 10% to 90% of final VSYS valuemin 1.33 · typ 1.7 · max 2 V/ms13
Soft start slew rate for GATE_VSYS, setting 3 SSTPS25751D; 4 V ≤ VVBUS ≤ 22 V, ILOAD = 100 mA, 500 pF < CGATE_VSYS < 16 nF, measure slope from 10% to 90% of final VSYS valuemin 2.8 · typ 3.3 · max 3.8 V/ms13
VBUS overvoltage protection for RCP programmable range VOVP4RCPOVP detected when VVBUS > VOVP4RCPmin 5 · max 24 V14
Hysteresis VOVP4RCPH3.0 V ≤ VVIN_3V3 ≤ 3.6 Vmin 1.75 · typ 2 · max 2.25 %14
Ratio of OVP4RCP input used for OVP4VSYS comparator. rOVP × VOVP4VSYS = VOVP4RCP rOVPsetting 0typ 1 V/V14
Ratio of OVP4RCP input used for OVP4VSYS comparator. rOVP × VOVP4VSYS = VOVP4RCP rOVPsetting 1typ 0.95 V/V14
Ratio of OVP4RCP input used for OVP4VSYS comparator. rOVP × VOVP4VSYS = VOVP4RCP rOVPsetting 2typ 0.9 V/V14
Ratio of OVP4RCP input used for OVP4VSYS comparator. rOVP × VOVP4VSYS = VOVP4RCP rOVPsetting 3typ 0.875 V/V14
VBUS overvoltage protection range for VSYS protection VOVP4VSYSOVP detected when rOVP × VVBUS > VOVP4RCPmin 5 · max 27.5 V14
Hysteresis VOVP4VSYSVBUS falling, % of VOVP4VSYS, rOVP setting 0min 1.75 · typ 2 · max 2.25 %14
Hysteresis VOVP4VSYSVBUS falling, % of VOVP4VSYS, rOVP setting 1min 1.8 · typ 2.1 · max 2.4 %14
Hysteresis VOVP4VSYSVBUS falling, % of VOVP4VSYS, rOVP setting 2min 1.9 · typ 2.2 · max 2.5 %14
Hysteresis VOVP4VSYSVBUS falling, % of VOVP4VSYS, rOVP setting 3min 2 · typ 2.3 · max 2.6 %14
Voltage required on PP5V VPP5V_UVLOrisingmin 3.9 · typ 4.1 · max 4.3 V14
Voltage required on PP5V VPP5V_UVLOfallingmin 3.8 · typ 4 · max 4.2 V14
Voltage required on PP5V VPP5V_UVLOhysteresistyp 0.1 V14
VBUS discharge current IDSCHVVBUS = 22 V, measure IVBUSmin 4 · max 15 mA14
Unattached CCy open circuit voltage while Rp enabled, no load VOC_3.3Type-C Source (Rp pullup); VLDO_3V3 > 2.302 V, RCC = 47 kΩmin 1.85 V14
Attached CCy open circuit voltage while Rp enabled, no load VOC_5Type-C Source (Rp pullup); VPP5V > 3.802 V, RCC = 47 kΩmin 2.95 V14
Unattached reverse current on CCy IRevVCCy = 5.5 V, VCCx = 0 V, VLDO_3V3_UVLO < VLDO_3V3 < 3.6 V, VPP5V = 3.8 V, measure current into CCymax 10 uA14
Unattached reverse current on CCy IRevVCCy = 5.5 V, VCCx = 0 V, VLDO_3V3_UVLO < VLDO_3V3 < 3.6 V, VPP5V = 0, TJ ≤ 85°C, measure current into CCymax 10 uA14
Current source - USB Default IRpDef0 < VCCy < 1.0 V, measure ICCymin 64 · typ 80 · max 96 uA14
Current source - 1.5 A IRp1.54.75 V < VPP5V < 5.5 V, 0 < VCCy < 1.5 V, measure ICCymin 166 · typ 180 · max 194 uA14
Current source - 3.0 A IRp3.04.75 V < VPP5V < 5.5 V, 0 < VCCy < 2.45 V, measure ICCymin 304 · typ 330 · max 356 uA14
Open/Default detection threshold when Rd applied to CCy VSNK1Type-C Sink (Rd pulldown); risingmin 0.2 · max 0.24 V14
Open/Default detection threshold when Rd applied to CCy VSNK1fallingmin 0.16 · max 0.2 V15
Hysteresis VSNK1Open/Default detection threshold when Rd applied to CCytyp 0.04 V15
Default/1.5-A detection threshold VSNK2fallingmin 0.62 · max 0.68 V15
Default/1.5-A detection threshold VSNK2risingmin 0.63 · typ 0.66 · max 0.69 V15
Hysteresis VSNK2Default/1.5-A detection thresholdtyp 0.01 V15
1.5-A/3.0-A detection threshold when Rd applied to CCy VSNK3fallingmin 1.17 · max 1.25 V15
1.5-A/3.0-A detection threshold when Rd applied to CCy VSNK3risingmin 1.22 · max 1.3 V15
Hysteresis VSNK31.5-A/3.0-A detection threshold when Rd applied to CCytyp 0.05 V15
Rd pulldown resistance RSNK0.25 V ≤ VCCy ≤ 2.1 V, measure resistance on CCymin 4.6 · max 5.6 kΩ15
VCONN discharge resistance RVCONN_DIS0V ≤ VCCy ≤ 5.5 V, measure resistance on CCymin 4 · max 6.12 kΩ15
Dead battery Rd clamp VCLAMPVVIN_3V3 = 0 V, 64 uA < ICCy < 96 uAmin 0.25 · max 1.32 V15
Dead battery Rd clamp VCLAMPVVIN_3V3 = 0 V, 166 uA < ICCy < 194 uAmin 0.65 · max 1.32 V15
Dead battery Rd clamp VCLAMPVVIN_3V3 = 0 V, 304 uA < ICCy < 356 uAmin 1.2 · max 2.18 V15
Resistance from CCy to GND when configured as open ROpenVVBUS = 0, VVIN_3V3 = 3.3 V, VCCy = 5 V, measure resistance on CCymin 500 kΩ15
Resistance from CCy to GND when configured as open ROpenVVBUS = 5 V, VVIN_3V3 = 0, VCCy = 5 V, measure resistance on CCymin 500 kΩ15
Rdson of the VCONN path RPP_CABLEVPP5V = 5 V, IL = 250 mA, measure resistance from PP5V to CCymax 1.2 Ω15
Short circuit current limit ILIMVCSetting 0, VPP5V = 5 V, RL=10 mΩ, measure ICCymin 350 · typ 410 · max 470 mA15
Short circuit current limit ILIMVCSetting 1, VPP5V = 5 V, RL=10 mΩ, measure ICCymin 540 · typ 600 · max 660 mA15
Reverse leakage current through VCONN FET ICC2PP5VVCONN disabled, TJ ≤ 85°C, VCCy = 5.5 V, VPP5V = 0 V, VVBUS = 5 V, LDO forced to draw from VBUS, measure ICCymax 10 uA15
Overvoltage protection threshold for PP_CABLE VVC_OVPVPP5V risingmin 5.6 · typ 5.9 · max 6.2 V15
Reverse current protection threshold for PP_CABLE, sourcing VCONN through CCx VVC_RCPVPP5V ≥ 4.9 V, VCCy = VPP5V, VCCx risingmin 60 · typ 200 · max 340 mV15
Reverse current protection threshold for PP_CABLE, sourcing VCONN through CCx VVC_RCPVPP5V ≥ 4.9 V, VCCy ≤ 4 V, VCCx risingmin 210 · typ 340 · max 470 mV15
Current clamp deglitch time tVCILIM3.0 V ≤ VVIN_3V3 ≤ 3.6 Vtyp 1.3 ms15
Time to disable PP_CABLE after VPP5V > VVC_OVP or VCCx - VPP5V > VVC_RCP tPP_CABLE_FSDCL = 0typ 0.5 us15
From disable signal to CCy at 10% of final value tPP_CABLE_offIL = 250 mA, VPP5V = 5 V, CL = 0min 100 · typ 200 · max 300 us16
Response time to short circuit tiOS_PP_CABLEVPP5V = 5 V, for short circuit RL = 10 mΩtyp 2 us16
Transmit high voltage on CCy VTXHITransmitter; Standard External loadmin 1.05 · typ 1.125 · max 1.2 V16
Transmit low voltage on CCy VTXLOTransmitter; Standard External loadmin -75 · max 75 mV16
Transmit output impedance while driving the CC line using CCy ZDRIVERTransmitter; measured at 750 kHzmin 33 · typ 54 · max 75 Ω16
Rise time. 10 % to 90 % amplitude points on CCy, minimum is under an unloaded condition. Maximum set by TX mask tRiseTransmitter; CCCy = 520 pFmin 300 ns16
Fall time. 90 % to 10 % amplitude points on CCy, minimum is under an unloaded condition. Maximum set by TX mask tFallTransmitter; CCCy = 520 pFmin 300 ns16
OVP detection threshold for USB PD PHY VPHY_OVP0 ≤ VVIN_3V3 ≤ 3.6 V, 0 ≤ VPP5V ≤ 5.5 V, VVBUS ≥ 4 V. Initially VCC1 ≤ 5.5 V and VCC2 ≤ 5.5 V, then VCCx risesmin 5.5 · max 8.5 V16
Receiver input impedance on CCy ZBMCRXReceiver; does not include pullup or pulldown resistance from cable detect. Transmitter is Hi-Zmin 1 MΩ16
Receiver capacitance on CCy CCCCapacitance looking into the CC pin when in receiver mode; internal capacitance onlymax 120 pF16
Rising threshold on CCy for receiver comparator VRX_SNK_RSink mode (rising)min 499 · typ 525 · max 551 mV16
Rising threshold on CCy for receiver comparator VRX_SRC_RSource mode (rising)min 784 · typ 825 · max 866 mV16
Falling threshold on CCy for receiver comparator VRX_SNK_FSink mode (falling)min 230 · typ 250 · max 270 mV16
Falling threshold on CCy for receiver comparator VRX_SRC_FSource mode (falling)min 523 · typ 550 · max 578 mV16
Temperature shutdown threshold TSD_MAINTemperature risingmin 145 · typ 160 · max 175 °C17
Temperature shutdown threshold TSD_MAINHysteresistyp 15 °C17
Temperature controlled shutdown threshold. The power paths for each port sourcing from PP5V and PP_CABLE power paths have local sensors that disables them when the temperature is exceeded TSD_PP5VTemperature risingmin 135 · typ 150 · max 165 °C17
Temperature controlled shutdown threshold. The power paths for each port sourcing from PP5V and PP_CABLE power paths have local sensors that disables them when the temperature is exceeded TSD_PP5VHysteresistyp 10 °C17
Least significant bit LSB3.6-V max scaling, voltage divider of 3typ 14 mV17
Least significant bit LSB25.2-V max scaling, voltage divider of 21typ 98 mV17
Least significant bit LSB4.07-A max scalingtyp 16.5 mA17
Gain error GAIN_ERR0.05 V ≤ VADCINx ≤ 3.6 V, VADCINx ≤ VLDO_3V3; 0.05 V ≤ VGPIOx ≤ 3.6 V, VGPIOx ≤ VLDO_3V3min -2.7 · max 2.7 %17
Gain error GAIN_ERR2.7 V ≤ VLDO_3V3 ≤ 3.6 Vmin -2.4 · max 2.4 %17
Gain error GAIN_ERR0.6 V ≤ VVBUS ≤ 22 Vmin -2.1 · max 2.1 %17
Gain error GAIN_ERR1 A ≤ IVBUS ≤ 3 Amin -2.1 · max 2.1 %17
Offset error VOS_ERR0.05 V ≤ VADCINx ≤ 3.6 V, VADCINx ≤ VLDO_3V3; 0.05 V ≤ VGPIOx ≤ 3.6 V, VGPIOx ≤ VLDO_3V3; specified after voltage dividermin -4.1 · max 4.1 mV17
Offset error VOS_ERR2.7 V ≤ VLDO_3V3 ≤ 3.6 V; specified after voltage dividermin -4.5 · max 4.5 mV17
Offset error VOS_ERR0.6 V ≤ VVBUS ≤ 22 V; specified after voltage dividermin -4.1 · max 4.1 mV17
Offset error VOS_ERR1 A ≤ IVBUS ≤ 3 A; specified after voltage dividermin -4.5 · max 4.5 mA17
GPIOx high-Level input voltage GPIO_VIHUSB_P, USB_N; VLDO_3V3 = 3.3 Vmin 1.3 V17
GPIOx low-level input voltage GPIO_VILUSB_P, USB_N; VLDO_3V3 = 3.3 Vmax 0.54 V17
GPIOx input hysteresis voltage GPIO_HYSUSB_P, USB_N; VLDO_3V3 = 3.3 Vmin 0.09 V17
GPIOx leakage current GPIO_ILKGUSB_P, USB_N; VGPIOx = 3.45 Vmin -1 · max 1 uA17
GPIOx internal pullup GPIO_RPUUSB_P, USB_N; Pullup enabledmin 50 · typ 100 · max 150 kΩ17
GPIOx internal pulldown GPIO_RPDUSB_P, USB_N; Pulldown enabledmin 50 · typ 100 · max 150 kΩ17
GPIOx input deglitch GPIO_DGUSB_P, USB_Ntyp 20 · max 50 ns17
GPIOx output high voltage GPIO_VOHGPIO0-7 (Outputs); VLDO_3V3 = 3.3 V, IGPIOx= -2 mAmin 2.9 V17
GPIOx output low voltage GPIO_VOLGPIO0-7 (Outputs); VLDO_3V3 = 3.3 V, IGPIOx = 2 mAmax 0.4 V17
ADCINx leakage current ADCIN_ILKGADCIN1, ADCIN2; VADCINx ≤ VLDO_3V3min -1 · max 1 uA18
Time from LDO_3V3 going high until ADCINx is read for configuration tBOOTADCIN1, ADCIN2typ 10 ms18
DCD source current IDP_SRCDATA CONTACT DETECT; VLDO_3V3 = 3.3 Vmin 7 · typ 10 · max 13 uA18
DCD pulldown resistance RDM_DWNDATA CONTACT DETECT; VUSB_N = 3.6 Vmin 14.25 · typ 20 · max 24.8 kΩ18
DCD pulldown resistance RDP_DWNDATA CONTACT DETECT; VUSB_P = 3.6 Vmin 14.25 · typ 20 · max 24.8 kΩ18
Threshold for no connection VLGC_HIDATA CONTACT DETECT; VUSB_P ≥ VLGC_HI, VLDO_3V3 = 3.3 V, RUSB_P = 300 kΩmin 2 · max 3.6 V18
Threshold for connection VLGC_LODATA CONTACT DETECT; VUSB_N ≤ VLGC_LO, VLDO_3V3 = 3.3 V, RUSB_P = 24.8 kΩmin 0 · max 0.8 V18
VDX_SRC current limit VDX_ILIMAdvertisement and Detectionmin 250 · max 400 uA18
Sink Current IDX_SNKAdvertisement and Detection; VUSB_P ≥ 250 mVmin 25 · typ 75 · max 125 uA18
Sink Current IDX_SNKAdvertisement and Detection; VUSB_N ≥ 250 mVmin 25 · typ 75 · max 125 uA18
Dedicated Charging Port Resistance RDCP_DATAdvertisement and Detection; 0.5 V ≤ VUSB_P ≤ 0.7 V, 25 uA ≤ IUSB_N ≤ 175 uAmax 200 Ω18
Low level output voltage OD_VOL_IRQI2Ct_IRQ; IOL = 2 mAmax 0.4 V18
Leakage Current OD_LKG_IRQI2Ct_IRQ; Output is Hi-Z, VI2Cx_IRQ = 3.45 Vmin -1 · max 1 uA18
High-Level input voltage IRQ_VIHI2Cc_IRQ; VLDO_3V3 = 3.3 Vmin 1.3 V18
High-Level input voltage threshold IRQ_VIH_THRESHI2Cc_IRQ; VLDO_3V3 = 3.3 Vmin 0.72 · max 1.3 V18
low-level input voltage IRQ_VILI2Cc_IRQ; VLDO_3V3 = 3.3 Vmax 0.54 V18
low-level input voltage threshold IRQ_VIL_THRESHI2Cc_IRQ; VLDO_3V3 = 3.3 Vmin 0.54 · max 1.08 V18
input hysteresis voltage IRQ_HYSI2Cc_IRQ; VLDO_3V3 = 3.3 Vmin 0.09 V18
input deglitch IRQ_DEGI2Cc_IRQtyp 20 ns18
I2C3m_IRQ leakage current IRQ_ILKGI2Cc_IRQ; VI2C3m_IRQ = 3.45 Vmin -1 · max 1 uA18
Input low signal VILSDA and SCL Common Characteristics (Controller, Target); VLDO_3V3 = 3.3 Vmax 0.54 V18
Max output low current IOLSDA and SCL Common Characteristics (Controller, Target); VOL = 0.4 Vmin 15 mA18
Max output low current IOLSDA and SCL Common Characteristics (Controller, Target); VOL = 0.6 Vmin 20 mA18
Fall time from 0.7 × VDD to 0.3 × VDD tfSDA and SCL Common Characteristics (Controller, Target); VDD = 1.8 V, 10 pF ≤ Cb ≤ 400 pFmin 12 · max 80 ns18
Fall time from 0.7 × VDD to 0.3 × VDD tfSDA and SCL Common Characteristics (Controller, Target); VDD = 3.3 V, 10 pF ≤ Cb ≤ 400 pFmin 12 · max 150 ns18
I2C pulse width suppressed tSPSDA and SCL Common Characteristics (Controller, Target)max 50 ns18
Capacitive load for each bus line (external) Cbmax 400 pF19
Clock frequency for target fSCLSSDA and SCL Standard Mode Characteristics (Target); VDD = 1.8 V or 3.3 Vmax 100 kHz19
Valid data time tVD;DATSDA and SCL Standard Mode Characteristics (Target); Transmitting Data, VDD = 1.8 V or 3.3 V, SCL low to SDA output validmax 3.45 us19
Valid data time of ACK condition tVD;ACKSDA and SCL Standard Mode Characteristics (Target); Transmitting Data, VDD = 1.8 V or 3.3 V, ACK signal from SCL low to SDA (out) lowmax 3.45 us19
Clock frequency for target fSCLSSDA and SCL Fast Mode Characteristics (Target); VDD = 1.8 V or 3.3 Vmin 100 · max 400 kHz19
Valid data time tVD;DATSDA and SCL Fast Mode Characteristics (Target); Transmitting data, VDD = 1.8 V, SCL low to SDA output validmax 0.9 us19
Valid data time of ACK condition tVD;ACKSDA and SCL Fast Mode Characteristics (Target); Transmitting data, VDD = 1.8 V or 3.3 V, ACK signal from SCL low to SDA (out) lowmax 0.9 us19
Clock frequency for Fast Mode Plus fSCLSTarget; VDD = 1.8 V or 3.3 V; controller must control fSCLS to ensure tLOW > tVD; ACKmin 400 · max 800 kHz19
Valid data time tVD;DATFast Mode Plus (Target); Transmitting data, VDD = 1.8 V or 3.3 V, SCL low to SDA output validmax 0.55 us19
Valid data time of ACK condition tVD;ACKFast Mode Plus (Target); Transmitting data, VDD = 1.8 V or 3.3 V, ACK signal from SCL low to SDA (out) lowmax 0.55 us19
Clock low time tLOWVDD = 3.3 Vmin 1.3 us19
Clock high time tHIGHVDD = 3.3 Vmin 0.6 us19
VBUS UVLO threshold VVBUS_UVLOrisingmin 3.6 · max 3.9 V11
VBUS UVLO threshold VVBUS_UVLOfallingmin 3.5 · max 3.8 V11
VBUS UVLO threshold VVBUS_UVLOhysteresistyp 0.1 V11
Rdson of VIN_3V3 to LDO_3V3 RLDO_3V3ILDO_3V3 = 50 mAmax 1.4 Ω11
Voltage on LDO_1V5 VLDO_1V5up to maximum internal loading conditionmin 1.49 · typ 1.5 · max 1.65 V11
Current into VIN_3V3 IVIN_3V3,ActSrcActive Source mode: VVBUS = 5.0 V, VVIN_3V3 = 3.3 Vtyp 3 mA11
Current into VIN_3V3 IVIN_3V3,ActSnkActive Sink mode: 22 V ≥ VVBUS ≥ 4.0 V, VVIN_3V3 = 3.3 Vtyp 3 · max 6 mA11
Current into VIN_3V3 IVIN_3V3,IdlSrcIdle Source mode: VVBUS = 5.0 V, VVIN_3V3 = 3.3 Vtyp 1 mA11
Current into VIN_3V3 IVIN_3V3,IdlSnkIdle Sink mode: 22 V ≥ VVBUS ≥ 4.0 V, VVIN_3V3 = 3.3 Vtyp 1 mA11
Power drawn into PP5V and VIN_3V3 in Modern Standby Sink Mode PMstbySnkCCm floating, VCCn = 0.4 V, VPP5V = 5 V, VVIN_3V3 = 3.3 V, VVBUS = 5.0 V, GATE_VBUS, GATE_VSYS disabled, and TJ = 25°Ctyp 4.1 mW11
Power drawn into PP5V and VIN_3V3 in Modern Standby Source Mode PMstbySrcCCm floating, CCn tied to GND through 5.1 kΩ, VPP5V = 5 V, VVIN_3V3 = 3.3 V, IVBUS = 0, TJ = 25°Ctyp 4.5 mW11
Current into PP5V IPP5V,SleepSleep mode: VPA_VBUS = 0 V, VVIN_3V3 = 3.3 Vtyp 2 uA11
Current into VIN_3V3 IVIN_3V3,SleepSleep mode: VVBUS = 0 V, VVIN_3V3 = 3.3 Vtyp 56 uA11
Resistance from PP5V to VBUS RPP_5VILOAD = 3 A, TJ = 25°Ctyp 36 · max 38 mΩ11
Resistance from PP5V to VBUS RPP_5VILOAD = 3 A,TJ = 125°Ctyp 36 · max 53 mΩ11
Current limit setting ILIM5VConfigure to setting 0min 1.15 · max 1.36 A11
Current limit setting ILIM5VConfigure to setting 1min 1.61 · max 1.9 A11
Current limit setting ILIM5Vmin 2.3 · max 2.7 A11
Current limit setting ILIM5VConfigure to setting 3min 3.04 · max 3.58 A11
Current limit setting ILIM5VConfigure to setting 4min 3.22 · max 3.78 A11
Hysteresis VOVP4RCPHmin 1.75 · typ 2 · max 2.25 %14
Hysteresis VSNK1typ 0.04 V15
Hysteresis VSNK2typ 0.01 V15
Hysteresis VSNK3typ 0.05 V15
Current clamp deglitch time tVCILIMtyp 1.3 ms15
Transmit high voltage on CCy VTXHIStandard External loadmin 1.05 · typ 1.125 · max 1.2 V16
Transmit low voltage on CCy VTXLOStandard External loadmin -75 · max 75 mV16
Transmit output impedance while driving the CC line using CCy ZDRIVERmeasured at 750 kHzmin 33 · typ 54 · max 75 Ω16
Rise time. 10 % to 90 % amplitude points on CCy, minimum is under an unloaded condition. Maximum set by TX mask tRiseCCCy = 520 pFmin 300 ns16
Fall time. 90 % to 10 % amplitude points on CCy, minimum is under an unloaded condition. Maximum set by TX mask tFallCCCy = 520 pFmin 300 ns16
Receiver input impedance on CCy ZBMCRXDoes not include pullup or pulldown resistance from cable detect. Transmitter is Hi-Zmin 1 MΩ16
Offset error VOS_ERR0.05 V ≤ VADCINx ≤ 3.6 V, VADCINx ≤ VLDO_3V3; 0.05 V ≤ VGPIOx ≤ 3.6 V, VGPIOx ≤ VLDO_3V3; specified after the voltage dividermin -4.1 · max 4.1 mV17
Offset error VOS_ERR2.7 V ≤ VLDO_3V3 ≤ 3.6 V; specified after the voltage dividermin -4.5 · max 4.5 mV17
Offset error VOS_ERR0.6 V ≤ VVBUS ≤ 22 V; specified after the voltage dividermin -4.1 · max 4.1 mV17
Offset error VOS_ERR1 A ≤ IVBUS ≤ 3 A; specified after the voltage dividermin -4.5 · max 4.5 mA17
GPIOx leakage current GPIO_ILKGVGPIOx = 3.45 Vmin -1 · max 1 uA17
GPIOx internal pullup GPIO_RPUPullup enabledmin 50 · typ 100 · max 150 kΩ17
GPIOx internal pulldown GPIO_RPDPulldown enabledmin 50 · typ 100 · max 150 kΩ17
GPIOx input deglitch GPIO_DGtyp 20 · max 50 ns17
Time from LDO_3V3 going high until ADCINx is read for configuration tBOOTtyp 10 ms18
DCD source current IDP_SRCVLDO_3V3 = 3.3 Vmin 7 · typ 10 · max 13 uA18
DCD pulldown resistance RDM_DWNVUSB_N = 3.6 Vmin 14.25 · typ 20 · max 24.8 kΩ18
DCD pulldown resistance RDP_DWNVUSB_P = 3.6 Vmin 14.25 · typ 20 · max 24.8 kΩ18
Threshold for no connection VLGC_HIVUSB_P ≥ VLGC_HI, VLDO_3V3 = 3.3 V, RUSB_P = 300 kΩmin 2 · max 3.6 V18
Threshold for connection VLGC_LOVUSB_N ≤ VLGC_LO, VLDO_3V3 = 3.3 V, RUSB_P = 24.8 kΩmin 0 · max 0.8 V18
Sink Current IDX_SNKVUSB_P ≥ 250 mVmin 25 · typ 75 · max 125 uA18
Sink Current IDX_SNKVUSB_N ≥ 250 mVmin 25 · typ 75 · max 125 uA18
Dedicated Charging Port Resistance RDCP_DAT0.5 V ≤ VUSB_P ≤ 0.7 V, 25 uA ≤ IUSB_N ≤ 175 uAmax 200 Ω18
I2C3m_IRQ leakage current IRQ_ILKGVI2C3m_IRQ = 3.45 Vmin -1 · max 1 uA18
Max output low current IOLSDA and SCL; VOL = 0.4 Vmin 15 mA18
Max output low current IOLSDA and SCL; VOL = 0.6 Vmin 20 mA18
Fall time from 0.7 × VDD to 0.3 × VDD tfSDA and SCL; VDD = 1.8 V, 10 pF ≤ Cb ≤ 400 pFmin 12 · max 80 ns18
Fall time from 0.7 × VDD to 0.3 × VDD tfSDA and SCL; VDD = 3.3 V, 10 pF ≤ Cb ≤ 400 pFmin 12 · max 150 ns18
I2C pulse width suppressed tSPSDA and SCLmax 50 ns18

Pins, by the datasheet

38
1 LDO_3V3
Supply output switched from VIN_3V3 or VBUS LDO; bypass with CLDO_3V3 to GND. · p. 5
2 ADCIN1
Configuration input; connect to a resistor divider to LDO_3V3. · p. 5
3 ADCIN2
Configuration input; connect to a resistor divider to LDO_3V3. · p. 5
4 LDO_1V5
CORE LDO output; bypass with CLDO_1V5 to GND; cannot source current to external circuits. · p. 5
5 GPIO0
General purpose digital I/O; tie to ground when unused. · p. 5
6 GPIO1
General purpose digital I/O; tie to ground when unused. · p. 5
7 GPIO2
General purpose digital I/O; tie to ground when unused. · p. 5
8 I2Ct_SDA
I2C target serial data input/output; pull up through a resistor; may be grounded if unused. · p. 5
9 I2Ct_SCL
I2C target serial clock input; pull up through a resistor; may be grounded if unused. · p. 5
10 I2Ct_IRQ
Active low I2C target interrupt; connect through a pull-up resistor; configurable as GPIO10; tie to ground if unused. · p. 5
11 GND
Ground; connect to ground plane. · p. 5
12 GND
Ground; connect to ground plane. · p. 5
13 GPIO11
General purpose digital I/O; tie to ground when unused. · p. 5
14 GND
Ground; connect to ground plane. · p. 5
15 DRAIN
Connects to drain of internal FET. · p. 5
16 I2Cc_SDA
I2C controller serial data input/output; pull up through a resistor; can be grounded if unused. · p. 5
17 I2Cc_SCL
I2C controller serial clock output; pull up through a resistor; can be grounded if unused. · p. 5
18 I2Cc_IRQ
Active low I2C controller interrupt; connect through a pull-up resistor; do not tie to GND when unused; configurable as GPIO12. · p. 5
19 GPIO3
General purpose digital I/O; tie to ground when unused. · p. 5
20 PPHV
High-voltage sinking node in the system. · p. 5
21 PPHV
High-voltage sinking node in the system. · p. 5
22 PPHV
High-voltage sinking node in the system. · p. 5
23 VBUS_IN
5-V to 20-V input. · p. 5
24 VBUS_IN
5-V to 20-V input. · p. 5
25 VBUS_IN
5-V to 20-V input. · p. 5
26 GPIO4/USB_P/LD1
General purpose digital I/O, D+ for BC1.2, or Type-C liquid detection; tie to ground when unused. · p. 5
27 GPIO5/USB_N/LD2
General purpose digital I/O, D- for BC1.2, or Type-C liquid detection; tie to ground when unused. · p. 5
28 CC1
USB Type-C I/O; filter noise with recommended CCCy capacitor to GND. · p. 5
29 CC2
USB Type-C I/O; filter noise with recommended CCCy capacitor to GND. · p. 5
30 DRAIN
Connects to drain of internal FET. · p. 5
31 GND
Ground; connect to ground plane. · p. 5
32 VBUS
5-V output from PP5V input to LDO; bypass with CVBUS to GND. · p. 5
33 VBUS
5-V output from PP5V input to LDO; bypass with CVBUS to GND. · p. 5
34 PP5V
5-V system supply to VBUS and supply for CCy pins as VCONN. · p. 5
35 PP5V
5-V system supply to VBUS and supply for CCy pins as VCONN. · p. 5
36 GPIO7
General purpose digital I/O; tie to ground when unused. · p. 5
37 GPIO6
General purpose digital I/O; tie to ground when unused. · p. 5
38 VIN_3V3
Supply for core circuitry and I/O; bypass with CVIN_3V3 to GND. · p. 5

Open-source boards using it

3
  • 2 layersUsb, the printed circuit board in 3D

    Usb

    wozniak-works/X1-palmrest-to-keyboard

    A custom replacement board for the Lenovo ThinkPad X1 Carbon palmrest to transform it to keyboard with integrated powerbank and usb hub.

    186 parts
  • 6 layers43.2 × 74.4 mmMonolith, the printed circuit board in 3D

    Monolith

    MidwestMotorBoy/Battery-Bank

    Monolith: an ultralight IP67 power bank for backpacking. 4S BAK 65E 21700 (91 Wh, under the 100 Wh airline limit), two bidirectional 100 W USB-C PD ports, Bluetooth LE (TI CC2340) with an iPhone app.

    289 parts
  • 4 layers191 × 130 mmFilltest, the printed circuit board in 3D

    Filltest

    zOnlyKroks/pcb-consortium

    193 partsCC0-1.0

Questions

What package is the TPS25751DREFR?

WQFN-38(6x4), with 44 pins.

Where is the TPS25751DREFR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS25751DREFR?

JLCPCB lists it as part C30169739, with 0 in stock; the sellers' links on this page open their listings.

Which open-source boards use the TPS25751DREFR?

3 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.