
BOOSTV2
zhaque3/DC-DC-Boost-Converter
A repository consisting of the PCB Design and firmware for DC-DC Boost converter on the University of Alberta EcoCar vehicle.

A repository consisting of the PCB Design and firmware for DC-DC Boost converter on the University of Alberta EcoCar vehicle.
BOOSTV3 is an open-source printed circuit board by zhaque3, from the zhaque3/DC-DC-Boost-Converter repository on GitHub. It is a 4-layer board of 100 × 100 mm with 199 parts on 105 nets, routed with 989 tracks and 777 vias.
It is built around the MCP6007-E/SN, LM51231QRGRRQ1 and AZ1117IH-3.3, with the AZ1117IH-5.0, ESDALC6V1W5 and MCP2542FD among its other parts. Its parts include 55 capacitors, 46 resistors, 22 diodes, 21 ICs and 4 transistors. It belongs with the power boards of this library.
Project: DC Boost Board — a programmable boost converter for the University of Alberta EcoCar 2025 Prototype Vehicle. The vehicle (Sally) won first place at the Shell Eco Marathon 2025 in the Hydrogen Fuel Cell Prototype Category.
Purpose: This board takes the vehicle's hydrogen fuel cell output voltage (nominally 24 V) and provides a controllable boosted output (typical target: 48 V) for the motor controller and motor. It includes measurement (voltage/current sensing), safety/protection (eFuses and monitoring), an MCU running FreeRTOS for control and telemetry, a simple local UI (OLED + push buttons), and CAN bus communication with other boards on the vehicle and wireless base station.
SET_VOLT value to an appropriate DAC code.The firmware running on the DC Boost Board is FreeRTOS based and implemented entirely in app_freertos.c.
The system is structured as a set of independent FreeRTOS tasks, each responsible for a specific functional domain: power control, sensing, user interface, and vehicle communication.
app_freertos.c)StartDefaultTask)SET_VOLT) with bounds checking based on input voltage.StartAdcConv)startScreenPrint)StartTRKPin)SET_VOLT into a proportional DAC output corresponding to the desired boost output voltage.StartStatusLED)| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100n | Capacitor_SMD:C_0603_1608Metric | C10, C20, C21, C22, C23, C24, C28, C34, C35, C36, C37, C38, C39, C40, C43 |
| 9 | 7.5k | Resistor_SMD:R_0603_1608Metric | R16, R20, R21, R22, R23, R34, R35, R38, R39 |
| 8 | 1u | Capacitor_SMD:C_0603_1608Metric | C8, C9, C42, C44, C47, C48, C53, C54 |
| 8 | NTMFS4D0N08XT1G | ecocad_lib_footprints:PowerMosDFNHybrid | U4, U5, U6, U7, U8, U9, U10, U11 |
| 6 | 220R | Resistor_SMD:R_0603_1608Metric | R13, R14, R15, R17, R18, R19 |
| 6 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2, FID3, FID4, FID5, FID6 |
| 6 | MountingHole | MountingHole:MountingHole_3.5mm | H1, H2, H3, H4, H5, H6 |
| 5 | LOGO | LOGO | G***, G***, G***, G***, G*** |
| 4 | 22u | Capacitor_SMD:C_0805_2012Metric | C4, C5, C6, C7 |
| 4 | Blue | LED_SMD:LED_0603_1608Metric | D7, D8, D13, D14 |
| 4 | Green | LED_SMD:LED_0603_1608Metric | D6, D9, D16, D18 |
| 4 | MMSZ5226B-7-F | ecocad_lib_footprints:D_SOD_123_M | D1, D2, D19, D20 |
| 4 | Red | LED_SMD:LED_0603_1608Metric | D5, D10, D15, D17 |
| 4 | SI2302A-TPMSCT-ND | ecocad_lib_footprints:SOT-23-3_Adjusted | Q1, Q2, Q3, Q4 |
| 3 | 100k | Resistor_SMD:R_0603_1608Metric | R2, R9, R10 |
| 3 | 10n | Capacitor_SMD:C_0603_1608Metric | C13, C32, C41 |
| 3 | 10u | Capacitor_SMD:C_1210_3225Metric | C29, C30, C31 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric | R25, R26, R28 |
| 3 | 1k2 | Resistor_SMD:R_0603_1608Metric | R29, R30, R31 |
| 3 | 22u | Capacitor_SMD:C_0603_1608Metric | C17, C49, C50 |
| 3 | 470u | ecocad_lib_footprints:CAP_PAN_10X20_PAN | C1, C2, C3 |
| 3 | 470u | ecocad_lib_footprints:CAP_YX_16X31P5_RUB | C25, C26, C27 |
| 2 | 0u1 | Capacitor_SMD:C_0603_1608Metric | C16, C55 |
| 2 | 10 | Resistor_SMD:R_0603_1608Metric | R46, R47 |
| 2 | 10u | Capacitor_SMD:C_0603_1608Metric | C45, C46 |
| 2 | 12k | Resistor_SMD:R_0603_1608Metric | R32, R36 |
| 2 | 200k | Resistor_SMD:R_0603_1608Metric | R3, R8 |
| 2 | 2n2 | Capacitor_SMD:C_0603_1608Metric | C51, C52 |
| 2 | 30k | Resistor_SMD:R_0603_1608Metric | R33, R37 |
| 2 | 4k7 | Resistor_SMD:R_0603_1608Metric | R40, R41 |
| 2 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C19, C33 |
| 2 | ACS713xLCTR-30A | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1, U12 |
| 2 | BAT54S | Package_TO_SOT_SMD:SOT-23 | D21, D24 |
| 2 | BLUE | LED_SMD:LED_0603_1608Metric | D11, D12 |
| 2 | G*** | kibuzzard-67392652 | kibuzzard-67392652, kibuzzard-67392652 |
| 2 | MCP6007 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2, U20 |
| 2 | SW_SPDT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | SW1, SW2 |
| 2 | TPS259631 | Package_SO:TI_SO-PowerPAD-8 | U17, U18 |
| 2 | ~ | ecocad_lib_footprints:PowerPole15-45BoardEdge2x1 | U21, U22 |
| 1 | 1.461u | ecocad_lib_footprints:3u3_induc | L1 |
| 1 | 100n | Resistor_SMD:R_0603_1608Metric | C18 |
| 1 | 100p | Capacitor_SMD:C_0805_2012Metric | C12 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R24 |
| 1 | 13k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | 15n | Capacitor_SMD:C_0603_1608Metric | C14 |
| 1 | 25k | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 27k | Resistor_SMD:R_0603_1608Metric | R42 |
| 1 | 28k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 300R | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | 330n | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 3k | Resistor_SMD:R_0603_1608Metric | R43 |
| 1 | 3k6 | Resistor_SMD:R_0603_1608Metric | R44 |
| 1 | 470p | Capacitor_SMD:C_0603_1608Metric | C15 |
| 1 | 50k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 68k | Resistor_SMD:R_0603_1608Metric | R45 |
| 1 | 6k98 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 722u | ecocad_lib_footprints:1u5_res_ | R11 |
| 1 | 8k | Resistor_SMD:R_0603_1608Metric | R27 |
| 1 | AZ1117IH-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U16 |
| 1 | AZ1117IH-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U15 |
| 1 | ESDALC6V1W5 | ecocad_lib_footprints:SOT65P210X110-5N | IC1 |
| 1 | G*** | kibuzzard-67B8F697 | kibuzzard-67B8F697 |
| 1 | G*** | kibuzzard-67B58E58 | kibuzzard-67B58E58 |
| 1 | G*** | kibuzzard-6906855D | kibuzzard-6906855D |
| 1 | G*** | kibuzzard-67BA360B | kibuzzard-67BA360B |
| 1 | G*** | kibuzzard-67B58E6E | kibuzzard-67B58E6E |
| 1 | G*** | kibuzzard-6905B3C6 | kibuzzard-6905B3C6 |
| 1 | G*** | kibuzzard-67B540FD | kibuzzard-67B540FD |
| 1 | G*** | kibuzzard-67B37C45 | kibuzzard-67B37C45 |
| 1 | G*** | kibuzzard-6905B3A4 | kibuzzard-6905B3A4 |
| 1 | G*** | kibuzzard-67BA3C10 | kibuzzard-67BA3C10 |
| 1 | G*** | kibuzzard-69068C4B | kibuzzard-69068C4B |
| 1 | G*** | kibuzzard-67BA362A | kibuzzard-67BA362A |
| 1 | G*** | kibuzzard-6743FE8B | kibuzzard-6743FE8B |
| 1 | G*** | kibuzzard-69068C38 | kibuzzard-69068C38 |
| 1 | LM51231QRGRRQ1 | ecocad_lib_footprints:RGR0020C-MFG | U3 |
| 1 | LOGO | RB_FTP:ecocar_logo | G*** |
| 1 | MCP2542FD | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U13 |
| 1 | MMSZ5257BT1G | Diode_SMD:D_SOD-123 | D23 |
| 1 | MMSZ5266BT1G | Diode_SMD:D_SOD-123 | D22 |
The 186 most common of 199 parts.

zhaque3/DC-DC-Boost-Converter
A repository consisting of the PCB Design and firmware for DC-DC Boost converter on the University of Alberta EcoCar vehicle.

zhaque3/DC-DC-Boost-Converter
A repository consisting of the PCB Design and firmware for DC-DC Boost converter on the University of Alberta EcoCar vehicle.


MarkusVLA/Suunnattava-suuntamikrofoni
Suunnattava suuntamikrofoni on laite, jolla voidaan elektronisesti ohjata äänityksen suuntaa käännettävän suuntauksen avulla.

RWTH-EBC/OSIGBApp
Open-Source Internet of Things (IoT) Gateways for Building Automation Applications





It measures 100 × 100 mm and has 4 copper layers, 1.6 mm thick.
199 parts, built around the MCP6007-E/SN, LM51231QRGRRQ1, AZ1117IH-3.3 and AZ1117IH-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the zhaque3/DC-DC-Boost-Converter repository on GitHub, at the commit this page was made from: the board is DC-Boost Hardware/BOOSTV3/BOOSTV3.kicad_pcb and its schematic DC-Boost Hardware/BOOSTV2/BOOSTV2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask zhaque3 before reusing the design.