2 layers51.7 × 43.6 mm
STM32F103C8T6 2 layer design (with optimization)
Ferid10/STM32F103C8T6-design
my pcb design where i made a stm 32 board with temprature and pressure sensor using both spi and i2c communication
38 parts
2 layers50 × 63 mm
Zenith Development Board
zenitheesc/Zenith-Development-Board3The Zenith Development Board was developed to serve as a first project for the new members of the group.
- Size
- 50 × 63 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 69
- Nets
- 71
- Pads
- 271
- Tracks, vias
- 679, 114
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 16 Jun 2021
- Updated
- 16 Jun 2021
Overview
Zenith Development Board is an open-source printed circuit board by zenitheesc, from the zenitheesc/Zenith-Development-Board repository on GitHub, published under the MIT licence. It is a 2-layer board of 50 × 63 mm with 69 parts on 71 nets, routed with 679 tracks and 114 vias.
It is built around the STM32F103C8T6, BMP280 and MPU-6050, with the USBLC6-2P6, BAS16GWX and DMG1012T among its other parts. Its parts include 26 resistors, 17 capacitors, 7 diodes, 6 connectors and 5 ICs. It belongs with the microcontroller boards boards and the STM32 boards of this library.
Main components
6
STM32F103C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 20KB 2V~3.6V 32 Bit 37 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure Sensors
MPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometers
USBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)
BAS16GWX
SOD-1231.25V@150mA 100V 215mA 4ns 500nA@80V Independent SOD-123 Switching Diodes ROHSNexperiaSwitching Diodes
DMG1012T
SOT-523-55℃~+150℃ 1 N-channel 1V 20V 280mW 300mΩ@4.5V、400mΩ@2.5V、500mΩ@1.8V 5.37pF 60.67pF 630mA 736.6pC@4.5V 9.68pF SOT-523 MOSFETs ROHSDiodes IncorporatedMOSFETs
README
Model/Hardware/README.mdZenith Development Board
Development board based on the STM32F103C8T6 developed to introduce the group members to circuits similar to those that can be used in the projects, including light, acceleration, rotation, pressure and temperature sensors, as well as actuators such as Mosfets, Relays and Leds.
Schematic
Layout
B.O.M.
| Component | Amount | Description |
|---|---|---|
| STM32F103C8T6 | 1 | Microcontroller |
| Crystal | 1 | 16MHz |
| MPU-6050 | 1 | Accelerometer and Gyroscope |
| BMP280 | 1 | Pressure and temperature sensor |
| LDR | 1 | Light Dependent Resistor |
| RGB-LED | 1 | Led SMD |
| Button | 2 | Push button |
| ESD suppressor | 2 | 652-CGA0603MLC-12E |
| Micro USB | 1 | Micro USB connector |
| ESD Protection | 1 | USBLC6-4SC6Y |
| Linear regulator | 1 | LD1117S33TR |
| Rele | 1 | G5V-1-DC5 |
| Mosfet | 1 | DMG1012T-7 |
Parts
69| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C3, C11, C13, C20, C21 |
| 5 | 4.7K | Resistor_SMD:R_0805_2012Metric | R10, R11, R12, R18, R19 |
| 4 | 100n | Capacitor_SMD:C_0805_2012Metric | C5, C7, C8, C9 |
| 4 | 10K | Resistor_SMD:R_0805_2012Metric | R4, R16, R17, R26 |
| 4 | 22 | Resistor_SMD:R_0805_2012Metric | R6, R7, R14, R15 |
| 4 | 330 | Resistor_SMD:R_0805_2012Metric | R2, R5, R9, R24 |
| 3 | 100 | Resistor_SMD:R_0805_2012Metric | R8, R22, R23 |
| 3 | SW_Push | Button_Switch_SMD:SW_SPST_TL3305A | SW1, SW2, SW3 |
| 3 | TVS | Diode_SMD:D_0603_1608Metric | D3, D4, D7 |
| 2 | 220 | Resistor_SMD:R_0805_2012Metric | R20, R21 |
| 2 | 30p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C14, C15 |
| 2 | LED_Small | LED_SMD:LED_0805_2012Metric | D1, D5 |
| 1 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13 |
| 1 | 0.1uF | Capacitor_SMD:C_1206_3216Metric | C16 |
| 1 | 1.5K | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 100nF | Capacitor_SMD:C_1206_3216Metric | C1 |
| 1 | 10nF | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | 10uF | Capacitor_SMD:C_1206_3216Metric | C2 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric | R25 |
| 1 | 2.2nF | Capacitor_SMD:C_0805_2012Metric | C17 |
| 1 | 4u7 | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | BAS16GWX | Diode_SMD:D_SOD-123 | D6 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | Conn_01x10_Female | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J2 |
| 1 | Conn_01x12_Female | Connector_PinSocket_2.54mm:PinSocket_1x12_P2.54mm_Vertical | J7 |
| 1 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J5 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_SeikoEpson_FA238-4Pin_3.2x2.5mm | Y1 |
| 1 | DMG1012T | Package_TO_SOT_SMD:SOT-523 | Q1 |
| 1 | G5V-1 | Relay_THT:Relay_SPDT_Omron_G5V-1 | K1 |
| 1 | LD1117S33TR_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | LDR07 | OptoDevice:R_LDR_5.1x4.3mm_P3.4mm_Vertical | R3 |
| 1 | LED_RGB | LED_SMD:LED_RGB_5050-6 | D2 |
| 1 | LOGO | LogosZenith:Logo_19,4mm | G*** |
| 1 | LOGO | LogosZenith:Logo_29,1mm | G*** |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U2 |
| 1 | STM32F103C8T6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U4 |
| 1 | Screw_Terminal_01x03 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-3-5.0-H_1x03_P5.00mm_Horizontal | J3 |
| 1 | USBLC6-2P6 | digikey-footprints:SOT23-6L | U1 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Amphenol_10103594-0001LF_Horizontal | J1 |
Questions
How big is the Zenith Development Board PCB?
It measures 50 × 63 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Zenith Development Board use?
69 parts, built around the STM32F103C8T6, BMP280, MPU-6050 and USBLC6-2P6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Zenith Development Board KiCad files?
From the zenitheesc/Zenith-Development-Board repository on GitHub, at the commit this page was made from: the board is Model/Hardware/Zenith_Development_Board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Zenith Development Board design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers50 × 50 mm
Flight Controller
sushs0305-arch/Flight-Controller-PCB-Design-using-STM32
Custom 2-layer flight controller PCB designed using KiCad based on the STM32F405RGTx microcontroller for drone and embedded robotics applications.
44 parts1 - 4 layers71.4 × 80.3 mm
Ex2
zaidhajji/Custom-Flight-Controller-Design-STM32F407-KiCad
Designed a custom flight controller board from schematic to layout: STM32F407VGTx MCU, MPU6050 IMU, BMP280 barometer, MicroSD logging, 6 servo/ESC outputs, and dual-stage power regulation.
93 parts - 2 layers55.9 × 58.2 mm
- 4 layers45.5 × 19.6 mm
Stm32 bluet pill
brendose/stm32_bluet_pill
This project is a 1.8V STM32WB55 Bluetooth Module with battery charging. The purpose of this project is to provide a development platform for mobile wearable devices.
93 parts1 - 4 layers65 × 75 mm
Stm devboard
AYUSH-pro-grammer/stm-devboard
A custom development board based on the STM32H573RIT6 microcontroller, created in KiCad that serves the purpose of learning about the hardware design, PCB layout, power supply and embedded systems.
70 parts - 4 layers25 × 50 mm
- 2 layers
