
ESP32
KirtiChickamath/ESP32-IoT-sensor-board
ESP32- IoT sensor board. 4-layer PCB, designed in KiCad . Features LiPo charging, USB-C, SPI flash, SD card, BME280, and more.

This repository contains the complete hardware design of a custom ESP32-C3 based Smart Sensor Board, including schematics, PCB layout, and documentation. The design integrates robust power management, multiple sensors, data storage, USB connectivity, and auto-programming , making it suitable for IoT, data logging, and embedded systems development.
ESP-32 C3 demo project004 is an open-source printed circuit board by YUKESH0620, from the YUKESH0620/ESP32-C3-Sensor-PCB repository on GitHub, published under the MIT licence. It is a 4-layer board of 93.8 × 58.9 mm with 93 parts on 80 nets, routed with 778 tracks and 133 vias.
It is built around the ESP32-C3-WROOM-02-H4, MCP73871EV and BME280, with the MAX4466EXK+T, W25Q32JVSSIQ and GSD090012SEU among its other parts. Its parts include 33 resistors, 25 capacitors, 7 ICs, 6 diodes and 5 connectors. It belongs with the sensors and measurement boards and the ESP32 and RISC-V boards of this library.
This repository contains the complete hardware design of a custom ESP32-C3 based Smart Sensor Board, including schematics, PCB layout, and documentation.
The design integrates robust power management, multiple sensors, data storage, USB connectivity, and auto-programming, making it suitable for IoT, data logging, and embedded systems development.
USB-C / Li-Po Battery
│
MCP73831 Charger
│
+5V Rail
│
LM1117-3.3 LDO
│
+3.3V Rail
│
ESP32-C3 MCU
│ │ │ │
│ │ │ Microphone + MAX4466
│ │ BME280 (I2C)
│ LDR (ADC)
SD Card (SPI)
|
SPI Flash| Ref | Component | Value / Part |
|---|---|---|
| U1 | ESP32 MCU | ESP32-C3-WROOM-02 |
| U2 | Env Sensor | BME280 |
| U3 | USB-UART | CP2102N |
| U4 | Charger IC | MCP73831 |
| U5 | LDO Regulator | LM1117-3.3 |
| U6 | SPI Flash | W25Q32 |
| U7 | Mic Amplifier | MAX4466 |
| J1 | USB Connector | USB Type-C |
| J2 | Battery Connector | JST-PH-2 |
| J3 | SD Card Socket | SPI SD |
| Ref | Value | Purpose |
|---|---|---|
| R1 | 10kΩ | MCP73831 PROG |
| R2 | 10kΩ | MCP73831 PROG |
| R3 | 5.1kΩ | USB-C CC pull-down |
| R4 | 5.1kΩ | USB-C CC pull-down |
| R5 | 2kΩ | MCP73831 status |
| R6 | 20kΩ | MCP73831 status |
| R7 | 470Ω | Charging LED |
| R8 | 470Ω | Charged LED |
| R9 | 470Ω | Fault LED |
| R10 | 470Ω | Power LED |
| R11 | 1kΩ | USB VBUS link |
| R12 | 22.1kΩ | USB detection |
| R13 | 47.5kΩ | USB detection |
| R15 | 47k | Biasing resistor |
| R23 | 10kΩ | LDR voltage divider |
| R24 | 4.7kΩ | I²C pull-up |
| R25 | 4.7kΩ | I²C pull-up |
| R26 | 2kΩ | Mic bias |
| R27 | 1MΩ | Mic amp gain |
| R28 | 2kΩ | Mic bias |
| R29 | 1MΩ | Mic amp gain |
| R30 | 10kΩ | Mic amp |
| R31 | 2.2kΩ | Mic feedback |
| R32 | 10kΩ | Reset pull-up |
| R33 | 10kΩ | DTR control |
| R34 | 10kΩ | RTS control |
| Ref | Value | Purpose |
|---|---|---|
| C1 | 0.1µF | USB decoupling |
| C2 | 0.1µF | LDO input |
| C3 | 10µF | LDO bulk |
| C4 | 10µF | LDO output |
| C5 | 0.1µF | LDO output |
| C6 | 1µF | MCP73831 |
| C7 | 10µF | ESP32 supply |
| C8 | 0.1µF | ESP32 decoupling |
| C10 | 0.1µF | Sensor decoupling |
| C14 | 0.1µF | Flash decoupling |
| C15 | 0.1µF | BME280 |
| C17 | 10nF | Mic coupling |
| C18 | 0.1µF | Mic supply |
| C19 | 1µF | Mic amp |
| C20 | 0.1µF | Mic feedback |
| C21 | 0.1µF | BOOT debounce |
| C22 | 1µF | RESET debounce |
Note: Functional validation will be performed after PCB fabrication.
Yukesh S
Embedded Systems Enthusiast
This project is licensed under the MIT License.
You are free to use, modify, distribute, and commercialize this design, provided that the original copyright notice and license text are included.
See the LICENSE file for full details.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 0.1u | Capacitor_SMD:C_0805_2012Metric | C1, C2, C5, C8, C10, C13, C14, C15, C16, C18, C20, C21, C23 |
| 7 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R19, R23, R32, R33, R34 |
| 6 | 470 | Resistor_SMD:R_0805_2012Metric | R7, R8, R9, R10, R14, R18 |
| 4 | 10u | Esp-32_sensor_Board004_Footprints:T491A | C3, C4, C7, C12 |
| 4 | 50 | Resistor_SMD:R_0805_2012Metric | R15, R16, R20, R22 |
| 3 | 10n | Capacitor_SMD:C_0805_2012Metric | C17, C24, C25 |
| 3 | 1u | Capacitor_SMD:C_0805_2012Metric | C6, C11, C22 |
| 3 | 2k | Resistor_SMD:R_0805_2012Metric | R5, R26, R28 |
| 3 | LTST-C170KRKT | Esp-32_sensor_Board004_Footprints:LEDC2012X120N | LED1, LED4, LED6 |
| 2 | 0ZCH0110AF2E | Esp-32_sensor_Board004_Footprints:FUSC3226X100N | F1, F2 |
| 2 | 1M | Resistor_SMD:R_0805_2012Metric | R27, R29 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric | R11, R30 |
| 2 | 4k7 | Resistor_SMD:R_0805_2012Metric | R24, R25 |
| 2 | 5k1 | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q2, Q3 |
| 2 | LTST-C170GKT | Esp-32_sensor_Board004_Footprints:LEDC2012X120N | LED2, LED5 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C19 |
| 1 | 20k | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 22k | Resistor_SMD:R_0805_2012Metric | R31 |
| 1 | 22k1 | Resistor_SMD:R_0805_2012Metric | R12 |
| 1 | 35WR100KLFTR | Esp-32_sensor_Board004_Footprints:TRIM_35WR100KLFTR | R17 |
| 1 | 4.7u | Esp-32_sensor_Board004_Footprints:T491A | C9 |
| 1 | 47k5 | Resistor_SMD:R_0805_2012Metric | R13 |
| 1 | B2B-PH-SM4-TB | Esp-32_sensor_Board004_Footprints:JST_B2B-PH-SM4-TB | J2 |
| 1 | BME280 | Esp-32_sensor_Board004_Footprints:PSON65P250X250X100-8N | U2 |
| 1 | Boot | Esp-32_sensor_Board004_Footprints:SW_TL3305AF260QG | S1 |
| 1 | CMC-5042PF-AC | Esp-32_sensor_Board004_Footprints:CUI_CMC-5042PF-AC | MK1 |
| 1 | CP2102N-Axx-xQFN20 | Esp-32_sensor_Board004_Footprints:QFN50P400X400X100-21N | U4 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | Conn_01x05_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | ESP32-C3-WROOM-02-H4 | Esp-32_sensor_Board004_Footprints:MODULE_ESP32-C3-WROOM-02-H4 | U3 |
| 1 | GSD090012SEU | Esp-32_sensor_Board004_Footprints:AMPHENOL_GSD090012SEU | J3 |
| 1 | LM1117MPX-3.3 | Esp-32_sensor_Board004_Footprints:VREG_LM1117MPX-3.3 | VR1 |
| 1 | LTST-C170TBKT | Esp-32_sensor_Board004_Footprints:LEDC2012X120N | LED3 |
| 1 | MAX4466EXK | Esp-32_sensor_Board004_Footprints:SOT65P210X110-5N | U7 |
| 1 | MCP73871 | Esp-32_sensor_Board004_Footprints:QFN50P400X400X100-21N | U1 |
| 1 | Reset | Esp-32_sensor_Board004_Footprints:SW_TL3305AF260QG | S2 |
| 1 | SS-52400-002 | Esp-32_sensor_Board004_Footprints:BELFUSE_SS-52400-002 | J1 |
| 1 | TEMT6000X01 | Esp-32_sensor_Board004_Footprints:TRANS_TEMT6000X01 | Q1 |
| 1 | Test CS | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | Test CS-SD | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | Test MISO | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | Test MOSI | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | Test SCLK | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | W25Q32JVSSIQ | Esp-32_sensor_Board004_Footprints:SOIC127P790X216-8N | U6 |
The 90 most common of 93 parts.

KirtiChickamath/ESP32-IoT-sensor-board
ESP32- IoT sensor board. 4-layer PCB, designed in KiCad . Features LiPo charging, USB-C, SPI flash, SD card, BME280, and more.

chopda15/ESP32-sensor-board
Custom-designed ESP32-C3 IoT PCB with integrated Li-ion charging, environmental sensing, data logging, USB-C connectivity, and power-efficient embedded system architecture.




andrewcnjuguna/ESP32_BME690
Multi-room ESP32-S3 environmental sensor node that streams air-quality data to a Node.js server over Wi-Fi. Built around the Bosch BME690 with auxiliary light, sound and battery monitoring.

BBIkal/ESP32_IOT_Project
A compact 4-layer mixed-signal PCB designed in KiCad 9, built around the ESP32-C3 module for IoT sensor applications.

EngMeesh/ESP32_IoT_Dev_Board
A custom 4-layer IoT development board based on the ESP32-C3, featuring integrated LiPo battery management, a CP2102N USB-UART bridge, MicroSD support, and onboard environmental/audio sensors for embedded engineering…
It measures 93.8 × 58.9 mm and has 4 copper layers, 1.6 mm thick.
93 parts, built around the ESP32-C3-WROOM-02-H4, MCP73871EV, BME280 and MAX4466EXK+T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the YUKESH0620/ESP32-C3-Sensor-PCB repository on GitHub, at the commit this page was made from: the board is hardware_v0.2_Improved/Kicad_files_v0.2/ESP-32 C3 demo project004.kicad_pcb and its schematic hardware/Schematic_view/ESP-32 C3 demo project004.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).