

Flip Flop Modul
- Size
- 68.5 × 70 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 58
- Pads
- 158
- Tracks, vias
- 342, 10
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 13 May 2022
- Updated
- 14 Aug 2024
Overview
Flip Flop Modul is an open-source printed circuit board by yannickbock, from the yannickbock/saba repository on GitHub. It is a 2-layer board of 68.5 × 70 mm with 48 parts on 58 nets, routed with 342 tracks and 10 vias.
It is built around the ATMEGA8A-AU, LM78L05 and BC547. Its parts include 25 resistors, 4 capacitors, 4 diodes, 3 connectors and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3ATMEGA8A-AU
TQFP-32(7x7)-40℃~+85℃ 10bit 16MHz 1KB 2.7V~5.5V 23 512Byte 8 Bit 8KB AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LM78L05
SOT-89-3-55℃~+125℃@(Tj) 1 1.7V 100mA 20V 42uV 49dB@(120Hz) 5V 6mA Fixed Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSKEXINVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBC547
TO-92Bipolar (BJT)Jiangsu Changjing Electronics Technology (CJ)
Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 10k | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R21, R22, R23, R24, R33, R34, R41, R42, R43, R44, R51, R52, R53, R54, R61, R62 |
| 10 | BC547 | TO_SOT_Packages_THT:TO-92_Molded_Wide_Oval | T32, T41, T42, T51, T52, T61, T1001, T1003, T1006, T1011 |
| 8 | 1k | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R11, R12, R13, R14, R1001, R1003, R1006, R1011 |
| 4 | 5V1 | Diode_THT:D_DO-35_SOD27_P10.16mm_Horizontal | D11, D12, D13, D14 |
| 2 | 100nF | Capacitors_SMD:C_0805 | C3, C4 |
| 2 | 2.2µF | Capacitors_SMD:C_0805 | C1, C2 |
| 1 | 10k | Resistors_SMD:R_0805 | R1 |
| 1 | ATmega8A-AU | Housings_QFP:LQFP-32_7x7mm_Pitch0.8mm | U1 |
| 1 | Conn_01x05 | Flip-Flop-Modul:Connector_01x05_5mm_Stocko_Horizontal | J1 |
| 1 | Conn_01x13 | Flip-Flop-Modul:Connector_01x13_5mm | J2 |
| 1 | ICSP | Pin_Headers:Pin_Header_Straight_2x03_Pitch2.54mm | J3 |
| 1 | LM78L05 | TO_SOT_Packages_SMD:SOT-89-3 | U2 |
More from yannickbock/saba
12- 2 layers252 × 267.5 mm

- 2 layers252 × 172.5 mm

- 2 layers137 × 102 mm

- 2 layers95 × 70 mm

- 2 layers195 × 95 mm

- 2 layers95 × 60 mm

- 2 layers275 × 98 mm
%2B9241/hardware/Skalen-Beleuchtung.kicad_pcb.jpg?size=s&soon)
- 2 layers137 × 102 mm

- 2 layers95 × 60 mm

- 2 layers155 × 47.5 mm

- 2 layers95 × 60 mm

- 2 layers80 × 70 mm

Similar boards
- 2 layers

- 2 layers72 × 108 mm

Dummyload
STWuRCA-diy/DUMMYLOAD_V2
Open-source electronic dummy load for testing high-voltage linear power supplies (tube amplifier PSUs). Adjustable current load, measurement and protection. Includes PCB, firmware and enclosure.
65 parts2 - 4 layers84.1 × 66 mm

- 2 layers40.5 × 55.4 mm

- 2 layers302 × 135 mm

- 2 layers49 × 43 mm

- 2 layers

MP Tracker
elektra42/freifunk-open-mppt
Open hard- and software solar maximum power point tracker
70 parts89 - 2 layers99.1 × 40 mm

Questions
How big is the Flip Flop Modul PCB?
It measures 68.5 × 70 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Flip Flop Modul use?
48 parts, built around the ATMEGA8A-AU, LM78L05 and BC547. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Flip Flop Modul KiCad files?
From the yannickbock/saba repository on GitHub, at the commit this page was made from: the board is Module/Flip-Flop-Modul/hardware/Flip-Flop-Modul.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Flip Flop Modul design in my own project?
Its repository states no licence, so its author keeps all rights: ask yannickbock before reusing the design.