Skip to the content
2 layers80 × 60 mmFroyIndoor, the printed circuit board in 3D

FroyIndoor

xrstf/froy2

ESP8266 + BME280/680 indoor/outdoor hygrometer

Size
80 × 60 mm
Copper layers
2
Thickness
1.6 mm
Parts
37
Nets
28
Pads
129
Tracks, vias
205, 23
Pours
3
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
21 Aug 2021
Updated
29 Jan 2022

Overview

FroyIndoor is an open-source printed circuit board by xrstf, from the xrstf/froy repository on GitHub. It is a 2-layer board of 80 × 60 mm with 37 parts on 28 nets, routed with 205 tracks and 23 vias.

It is built around the BME280 and FT232RL. Its parts include 13 resistors, 6 capacitors, 3 ICs, 3 diodes and 3 transistors.

Main components

2

README

README.md

Frøy - ESP8266+BME Hygrometer

This repository contains the source code, schematics and everything else for my personal fancy homegrown hygrometer (sensor that reports temperature, humidity and pressure).

Features

  • push or pull mode
  • supports BME280, BME680 and BMP280 chips
  • programming via USB (only for indoor variant, others need a standalone USB->UART converter)
  • webserver with Prometheus compatible /metrics endpoint
  • reconfiguration via USB or WiFi (i.e. curl -XPOST -d'{"new":"config"}' http://device/)
  • OTA pull support (Frøy pulls new firmware from a specified location)
  • TLS support (single fingerprint only)
  • relatively easy to solder by hand (nothing smaller than an 0805 package)

Mode of Operation

Both indoor and outdoor versions can work in one of two modes:

  • Pull Mode ("server mode") -- in this mode, Frøy is constantly running and connected to your WiFi. It provides an HTTP server and expects you to fetch the data whenever you need it (for example via Prometheus).
  • Push Mode -- in this mode, Frøy will make a measurement, connect to WiFi, send out the data to a preconfigured URL and then go to sleep for a configurable amount of time. Rinse and repeat.

The advantage of the Pull Mode is that the interval can be centralled controlled (if you have multiple devices). It also makes it easier to trigger an OTA, as Frøy is constantly listening for requests.

The advantage of the Push Mode is that Frøy doesn't need any Firewall rules to be reachable and it saves power (critical for the Outdoor version). Also, indoor versions in Pull Mode would considerable heat up (an ESP8266 that is connected to WiFi can be 35-40°C) and skew the sensor readings. So even for indoor versions it is advisable to use Push Mode instead.

While Frøy is not reachable in Push Mode (it never starts a webserver and you'd be pretty luck to send a request to it the moment it wakes up and before it goes back to sleep), it is still possible to reconfigurable Frøy remotely by putting the new configuration in the response to Frøy's push request.

Flavors

Frøy currently comes in three flavors:

Frøy Outdoor

This is the original project. It runs using a CR123 battery, which lasts roughly 3-5 months when reporting data every 15 minutes.

The case can be bought on Amazon: https://www.amazon.de/gp/product/B072M2JKGW/ -- I am not aware of any alternative sources. In case the product disappears, I saved the schematics in docs/images/froy-outdoor-case-drawings.jpg.

Frøy Indoor

This variant is powered by USB and suitable for indoor use.

Froy ForMen

This variant is powered by mains voltage and is suitable for locations where changing the battery regularly is not desirable.

The case can be bought on Amazon, for example https://www.amazon.de/gp/product/B07B9KY9X4/ -- alternatively search for "Snowsound case" on your favorite search engine.


Frøy was named after the character in the NRK series "Norsemen".

Parts

37
QtyValueFootprintReferences
710kResistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolderR1, R2, R3, R4, R10, R12, R13
3100nFCapacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolderC2, C4, C6
312kResistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolderR8, R9, R11
3270Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolderR5, R6, R7
3Q_NPN_BECPackage_TO_SOT_SMD:SOT-23Q1, Q2, Q3
110nFCapacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolderC1
14.7uFCapacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolderC3
1470uFCapacitor_SMD:CP_Elec_10x12.5C5
1BME260_Breakoutxrstf:PinHeader_1x04_P2.54mm_VerticalJ2
1BME280xrstf:BME280_680_BMP280U2
1ESP-WROOM-02U__4MB_xrstf:ESP-WROOM-02UIC1
1FT232RLPackage_SO:SSOP-28_5.3x10.2mm_P0.65mmU1
1Ferrite_BeadInductor_SMD:L_1206_3216Metric_Pad1.42x1.75mm_HandSolderFB1
1LOGOxrstf:grouchoG***
1RXLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD3
1STATUSLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD1
1SW_SPSTButton_Switch_THT:SW_Tactile_SPST_Angled_PTS645Vx83-2LFSSW1
1TXLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD2
1USB_B_Minixrstf:USB_BWM_MIniUSB_THT_reicheltJ1

The 33 most common of 37 parts.

More from xrstf/froy

3
  • 2 layers78.9 × 47.2 mmFroyLogger, the printed circuit board in 3D

    FroyLogger

    xrstf/froy

    ESP8266 + BME280/680 indoor/outdoor hygrometer

    33 parts2
  • 2 layers77.6 × 47.2 mmFroyOutdoor, the printed circuit board in 3D

    FroyOutdoor

    xrstf/froy

    ESP8266 + BME280/680 indoor/outdoor hygrometer

    28 parts2
  • 2 layers105.6 × 57 mmFroyForMen, the printed circuit board in 3D

    FroyForMen

    xrstf/froy

    ESP8266 + BME280/680 indoor/outdoor hygrometer

    27 parts2

Similar boards

  • 2 layers98 × 60 mmNightStandClock, the printed circuit board in 3D

    NightStandClock

    LucasCanete/BasicClock

    A clock that shows the time and additionally the temperature and humidity

    64 parts
  • 2 layers100 × 140 mmWrectangle V4, the printed circuit board in 3D

    Wrectangle V4

    Wildcat-Rocket-Engineering-Club/WRECtangle

    WRECtangle code

    137 parts
  • 2 layers136.5 × 54.9 mmClimateSprinklerController, the printed circuit board in 3D

    ClimateSprinklerController

    kbx81/ClimateSprinklerController

    ESP32-based climate and sprinkler controller for use with ESPHome

    120 parts56
  • 2 layers68.8 × 53.6 mmZArduino, the printed circuit board in 3D

    ZArduino

    zmaker/arduino_cookbook

    gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

    46 parts269
  • 2 layers80.1 × 56.9 mmKwp1281tool, the printed circuit board in 3D

    Kwp1281tool

    mnaberez/vwradio

    Reverse engineering Volkswagen car radios

    33 parts133BSD-3-Clause
  • 2 layers45 × 69 mmUsbavrfloppy, the printed circuit board in 3D

    Usbavrfloppy

    jtsiomb/usbamigafloppy

    USB floppy controller for Amiga disks

    25 parts69CC-BY-SA-4.0
  • 2 layers100 × 71.8 mmBrutzelkarte, the printed circuit board in 3D

    Brutzelkarte

    jago85/Brutzelkarte_PCB

    Brutzelkarte - N64 Flash Cart PCB (KiCad)

    106 parts67GPL-3.0

Questions

How big is the FroyIndoor PCB?

It measures 80 × 60 mm and has 2 copper layers, 1.6 mm thick.

What parts does the FroyIndoor use?

37 parts, built around the BME280 and FT232RL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the FroyIndoor KiCad files?

From the xrstf/froy repository on GitHub, at the commit this page was made from: the board is kicad/FroyIndoor/FroyIndoor.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the FroyIndoor design in my own project?

Its repository states no licence, so its author keeps all rights: ask xrstf before reusing the design.