

EEE3088F PROJECT
The door unlocks if there is an object in close proximity and a certain sound is pplayed for some time. This is to be paired with a device that emits a sound, which is not in the scope of this project.
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 64
- Nets
- 96
- Pads
- 284
- Tracks, vias
- 337, 12
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 11 May 2026
- Updated
- 11 May 2026
Overview
EEE3088F PROJECT is an open-source printed circuit board by xNiDx, from the xNiDx/EEE3088F-PROJECT repository on GitHub, published under the MIT licence. It is a 2-layer board of 100 × 100 mm with 64 parts on 96 nets, routed with 337 tracks and 12 vias.
It is built around the CH340E, LM358M and VCNL36821S, with the AO3400A, AT24C256C-SSHL-T and FS312F-G among its other parts. Its parts include 14 resistors, 11 ICs, 10 capacitors, 2 diodes and 2 connectors. It belongs with the STM32 boards of this library.
Main components
8CH340E
MSOP-10150uA 20mA 2Mbps 3.3V、5V Transceiver USB 2.0 MSOP-10 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersLM358M
SOIC-8-16V~-1.5V、1.5V~16V 0℃~+70℃ 1MHz 2 20mA 2mV 3V~32V 45nA 500uA 5nA 7uV/℃ 85dB Built-in compensation SOIC-8 Operational Amplifier ROHSTexas InstrumentsOperational AmplifierVCNL36821S
SMD-8P-40℃~+85℃ 1.7V~3.6V 12bit 1mm 2.05mm 2.55mm I2C Light Intensity Low power/sleep mode、Adjustable gain control、Interrupt/event trigger、Built-in temperature compensation SMD-8P Ambient Light Sensors ROHSVishay IntertechnologyAmbient Light SensorsAO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsAT24C256C-SSHL-T
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 1MHz 256Kbit 40 Years 5ms Hardware write protection function、Noise suppression function I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROMFS312F-G
SOT-23-6-40℃~+85℃ 1 2.9V 2V~4.275V 3uA Lithium Battery Not supported Protection IC SOT-23-6 Battery Management ROHSFortune SemiconBattery ManagementLM2937L-33-TQ2-R
TO-263-3-40℃~+125℃ 1 100uVrms 10mA 26V 3.3V 500mA 500mV@(500mA) Fixed Over Temperature Protection、Short Circuit Protection Positive TO-263-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSUTCVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTP4056-42-ESOP8
ESOP-8-40℃~+85℃ 1 1A 2uA 4.2V 4V~8V Charging IC Lithium Battery Support ESOP-8 Battery Management ROHSTOPPOWERBattery Management
README
README.mdThe Project
Name
EEE3088F Team 20 "The Project" Sound/Proximity HAT
Description
Welcome to our project repository for a HAT (Hardware Attached on Top) that includes both a proximity and sound sensor for the STM32F0 series microcontroller. We are a team of 3 engineers who are passionate about embedded systems and hardware design. In this repository, you will find all the necessary resources to replicate our project and get started with your own HAT design.
The door unlocks if there is an object in close proximity and a certain sound is pplayed for some time. This is to be paired with a device that emits a sound, which is not in the scope of this project.
Features
Our HAT includes the following features:
- Proximity Sensor: We used the VCNL36821S proximity sensor to detect objects within a range of 2m. The sensor communicates with the microcontroller over I2C.
- Sound Sensor: We used the NSM2402AT-LL1 microphone to capture sound waves and convert them into digital signals. The microphone communicates with the microcontroller over an analog input.
Getting Started
To replicate our project, you will need the following components:
- STM32F0 series microcontroller
- VCNL36821S proximity sensor
- NSM2402AT-LL1 microphone
- PCB design software (we used KiCad)
You can find the schematic and PCB layout files in the /Main directory of this repository. Once you have assembled the components and flashed the firmware, you can test the HAT by running the demo code provided in the /Firmware directory.
Future Work
There are several ways to improve upon our design and add new features to the HAT. Some potential ideas include:
- Adding more sensors, such as temperature and humidity sensors
- Implementing wireless communication protocols, such as Bluetooth or Wi-Fi
- Developing a mobile app to interface with the HAT
Support
Roadmap
- Wk01 Project start
- Wk02 Concept Proposal
- Wk03 Design Proposal
- Wk04 Initial Schematic and Simulation Design
- Wk05 PCB Initial Designs
- Wk06 Peer review of PCB Design Reports
- Wk07 PCB Gerber Files Hand-in
- Wk08 Sensor Budget Tutorial
- Wk09 Draft final project design report
- Wk10 PCBs returned to students
- Wk11 Work on Report and Demo
- Wk12 Work on Report and Demo
- Wk13 Documentation and Software
- Wk14 Lab Demo / GA opportunity 2 (oral if required)
Credits
This project was made possible by the hard work and dedication of the following team members:
- Si Teng Wu: Microcontroller programmer
- Nüvit Ilkin Demirtaş: Sensing module design
- Joseph Stewart: Power systems design
License
This project is licensed under the MIT License.
Project status
Design Proposal --> Inital Design --> PCB Design --> PCB Gerbers
Parts
64| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | SIL_01x02_MALE | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | FP1, FP2, FP3, FP4, FP5, FP10, FP11, FP12, FP13, FP14, FP15, FP16, FP17, FP18, FP19, FP20 +4 |
| 5 | 0.1uF | Footprints:CAPC2012X140N | C3, C4, C5, C6, C7 |
| 4 | 0Ω | Resistor_SMD:R_1206_3216Metric | R6, R7, R8, R14 |
| 3 | 10kΩ | Resistor_SMD:R_0805_2012Metric | R1, R4, R5 |
| 3 | 10uF | Footprints:CAPC2012X135N | C8, C9, C10 |
| 3 | 1kΩ | Resistor_SMD:R_0805_2012Metric | R9, R10, R12 |
| 2 | 1.5kΩ | Resistor_SMD:R_0805_2012Metric | R2, R3 |
| 2 | 30pF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | AO3400A | Footprints:N MOSFET | U8, U10 |
| 2 | SIL_01x24_MALE | Connector_PinHeader_2.54mm:PinHeader_1x24_P2.54mm_Vertical | JP1, JP2 |
| 2 | Schottky | Footprints:DIOM5436X244N | D1, D2 |
| 1 | 1.2kΩ | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 100Ω | Resistor_SMD:R_0805_2012Metric | R13 |
| 1 | 18650 Connector | Footprints:BH-18650-B1BA002 | J2 |
| 1 | 8MHz Crystal | Footprints:CRYSTAL-SMD_L11.5-W4.8-LS12.7 | X1 |
| 1 | AT24C256C-SSHL-T | Footprints:SOIC127P600X175-8N | U1 |
| 1 | CH340E | Footprints:MSOP10 | U3 |
| 1 | FS312F-G | Footprints:FS312F-G | U9 |
| 1 | LM2937L-33-TQ2-R | Footprints:TO-263-3_L8.6-W10.2-P2.54-LS14.4-TL | U11 |
| 1 | LM358M | Footprints:SOIC127P599X175-8N | U6 |
| 1 | Micro USB | Footprints:USB_Conn_JLC_LCSC_C404969 | J1 |
| 1 | NSM2402AT-LL1 | Footprints:NSM2402AT-LL | U5 |
| 1 | Reset Switch (Push) | Footprints:SW_TS-1187A-B-A-B | S1 |
| 1 | SIL_01x10_MALE | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | JP3 |
| 1 | STM32F0 Target Sockets | Footprints:STM32F051C6T6 Sockets | U2 |
| 1 | TP4056-42-ESOP8 | Footprints:SOIC127P600X175-9N | U7 |
| 1 | VCNL36821S | Footprints:VCNL36821S | U4 |
Similar boards
- 2 layers121 × 73 mm

- 2 layers103 × 74.2 mm

LED CONTROLLER POT FO41B007FF584
manhoosbilli1/led-dimmer-pot-controller
Potentiometer-controlled LED dimmer board
42 parts - 2 layers

PLC V1
JosueHerrera05/Josue_Herrera_Electiva_2026_C2
Repositorio Electíva Diseño Mecatrónico 2026-C2
59 partsMIT - 2 layers96 × 70 mm

- 2 layers63.8 × 31.8 mm

18650 Battery Charging
Indhiraarunachalam/18650_Battery_Charging
18650 Lithium-Ion Battery Charging PCB designed using KiCad .
18 partsMIT - 2 layers28 × 17.1 mm

Tp4056 module
Roshan-khatri78/Electronics-Projects-KiCad-
A collection of my KiCad projects and PCB designs. These projects reflect my learning journey in electronics and PCB design.
19 parts2 - 2 layers40 × 20 mm

- 4 layers

Vibamix
CoolNamesAllTaken/vibamix
An interactive ePaper nametage for playing "will it blend" with arbitrary groups of people.
78 parts
Questions
How big is the EEE3088F PROJECT PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the EEE3088F PROJECT use?
64 parts, built around the CH340E, LM358M, VCNL36821S and AO3400A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the EEE3088F PROJECT KiCad files?
From the xNiDx/EEE3088F-PROJECT repository on GitHub, at the commit this page was made from: the board is Main/Main.kicad_pcb and its schematic Main/Main.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the EEE3088F PROJECT design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).