

Deck Mainboard
- Size
- 98 × 63.2 mm
- Copper layers
- 2
- Thickness
- 1.02 mm
- Parts
- 60
- Nets
- 90
- Pads
- 286
- Tracks, vias
- 599, 96
- Pours
- 21
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 12 Aug 2026
- Updated
- 20 Oct 2026
Overview
Deck Mainboard is an open-source printed circuit board by xKraZx, from the xKraZx/Pol-Deck repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 98 × 63.2 mm with 60 parts on 90 nets, routed with 599 tracks and 96 vias.
It is built around the RP2350B, W25Q128JVSIQ and AP2112K-3.3, with the USBLC6-2SC6 and ABM8-272-T3 among its other parts. Its parts include 21 capacitors, 14 resistors, 7 connectors, 5 ICs and 2 switches. It belongs with the computers and single-board computers boards and the RP2350 boards of this library.
Main components
5RP2350B
QFN-80-EP(10x10)48 Power-on reset (POR)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Integrated LDO、True random number generator (TRNG)、Hardware ECC check、Independent watchdog (IWDG) QFN-80-EP(10x10) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)ABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystals
README
README.mdPol-Deck
Parts
60| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 0.1u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C6, C7, C8, C9, C10, C11, C12, C13, C14, C16, C17, C18, C20 |
| 4 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R11, R12, R13, R14 |
| 4 | 4.7u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C2, C3, C15 |
| 4 | MH | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 2 | 0 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7, R9 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R6, R8 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C19, C21 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R3 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4, R5 |
| 2 | MH_P | MountingHole:MountingHole_3.2mm_M3_Pad | H5, H6 |
| 1 | 10u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C4 |
| 1 | 1u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5 |
| 1 | 3.3u | AOTA:AOTAB201610S3R3101T | L1 |
| 1 | 33 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
| 1 | ABM8-272-T3 | deckLib:ABM8-272-T3_ABR | X1 |
| 1 | ADDITIONAL PINS | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J6 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | APS6404L-3SQRx-SN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | BOOTSEL | Button_Switch_SMD:SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW2 |
| 1 | BUTTONS | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | DEBUG | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | DNP | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R10 |
| 1 | ENCODERS | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J3 |
| 1 | LCD | Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_Vertical | J4 |
| 1 | LED_G | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | PPTC | Fuse:Fuse_1812_4532Metric_Pad1.30x3.40mm_HandSolder | F1 |
| 1 | RESET | Button_Switch_SMD:SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW1 |
| 1 | RP2350B | Package_DFN_QFN:QFN-80-1EP_10x10mm_P0.4mm_EP3.4x3.4mm | U1 |
| 1 | SD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | SDO_SOD-123FL_ONS | D_sch:MBR120VLSFT1G | CR1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | deckLib:USB_C_vertical | J8 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U5 |
More from xKraZx/Pol-Deck
1- 2 layers98 × 62 mm

Similar boards
- 2 layers76.2 × 122.2 mm

Calculator full schematic revB
SCREAM325/TI_INFINITY
contains PCB file for PCBway and GCODE files for speaker case.
116 parts - 4 layers50 × 70 mm

- 4 layers165.5 × 51.6 mm

Panel
AlphaCassiopeiae/8800
Firmware and PCBs for aCassiopeiae, a minature Altair 8800 clone
222 parts1 - 4 layers96.5 × 85.5 mm

- 4 layers68.6 × 56 mm

Cartridge
coco-chameleon/chameleon-hardware
TRS-80 Color Computer cartridge emulator
95 partsCERN-OHL-W-2.0 - 2 layers121.5 × 70.7 mm

Atlas-11
hanshuebner/atlas-11
MOVED to code.netzhansa.com/hanshuebner/atlas-11. This GitHub mirror is archived.
44 partsMIT - 2 layers50 × 65 mm

RB Pirate
reza-bakhshi/RB-Pirate
RB-Pirate helps developers, makers, and hardware enthusiasts communicate with, analyze, and debug electronic devices directly from a terminal.
247 partsMIT - 4 layers15.7 × 40.1 mm

Pikey
Thenewtechgu/Pikey
My verson of a usb rubber ducky that can also be used as a storage device
49 parts
Questions
How big is the Deck Mainboard PCB?
It measures 98 × 63.2 mm and has 2 copper layers, 1.02 mm thick.
What parts does the Deck Mainboard use?
60 parts, built around the RP2350B, W25Q128JVSIQ, AP2112K-3.3 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Deck Mainboard KiCad files?
From the xKraZx/Pol-Deck repository on GitHub, at the commit this page was made from: the board is hardware/Deck_Mainboard/Deck_Mainboard.kicad_pcb and its schematic hardware/Deck_ButtonBoard/ButtonBoard/ButtonBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Deck Mainboard design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).